Search

This study reports the preparation of cellulose nanocrystals (CNCs) from commercial bleached eucalyptus Kraft pulp (BEKP) using a hydrothermal treatment in the presence of maleic acid (MA), followed by high-pressure homogenization. Compared with conventional hydrolysis methods, this approach offers significant advantages, including lower acid concentration, higher yield, and milder processing conditions. CNCs were produced with a high yield (70-85 wt %) by high-pressure homogenization of hydrothermally treated BEKP fibers with 10-20 wt % maleic acid at 150 °C, giving rise to a stable translucent gel of CNCs with a rod-like morphology (200-400 nm length and 10-40 nm width). The reinforcing potential of the CNCs was also assessed by preparing nanocomposite films with CNC contents of up to 15 wt %, and the results were compared to commercial CNCs from CelluForce. Additionally, their biodegradability in aquatic media was assessed using biological oxygen demand, with results compared to those of neat cellulose fibers. The MA-assisted hydrothermal process is an environmentally friendly alternative to conventional CNC production methods, offering higher yields and enhanced thermal stability while preserving a strong reinforcing property.

Lignin-containing cellulose nanofibrils (LCNFs) have attracted great attention because the presence of lignin brought additional merits to cellulose nanofibrils including hydrophobicity, ultraviolet (UV)-shielding capacity, and reduced water sensitivity. In the present work, LCNFs with lignin content up to 21 wt % were prepared with a high yield exceeding 70 wt %, from neat date palm waste, by a hydrothermal treatment (HTT) at 120-150 °C in the presence of 20-30 wt % maleic acid, followed by high-pressure homogenization. The chemical composition, degree of polymerization, morphology, and colloidal and rheological properties of the LCNFs were investigated to understand how the HTT in the presence of MA affected the properties of the resulting LCNFs. Nanopapers prepared from the LCNF suspensions exhibited mechanical properties lower than those from lignin-free CNF-based nanopapers, yet with decreased hydrophilicity. A mechanism explaining how the HTT in the presence of MA facilitated the disintegration of the biomass into nanoscale material was proposed. Overall, the present work demonstrated a feasible and scalable approach for the sustainable production of LCNF suspensions from neat agricultural residues, with a high yield and a high lignin content, without any need to perform a preliminary partial delignification.

In the nanomedicine field, there is a need to widen the availability of nanovectors to compensate for the increasingly reported side effects of poly(ethene glycol). Nanovectors enabling cross-linking can further optimize drug delivery. Cross-linkable polyoxazolines are therefore relevant candidates to address these two points. Here we present the synthesis of coumarin-functionalized poly(2-alkyl-2-oxazoline) block copolymers, namely, poly(2-methyl-2-oxazoline)- block -poly(2-phenyl-2-oxazoline) and poly(2-methyl-2-oxazoline)- block -poly(2-butyl-2-oxazoline). The hydrophilic ratio and molecular weights were varied in order to obtain a range of possible behaviors. Their self-assembly after nanoprecipitation or film rehydration was examined. The resulting nano-objects were fully characterized by transmission electron microscopy (TEM), cryo-TEM, multiple-angle dynamic and static light scattering. In most cases, the formation of polymer micelles was observed, as well as, in some cases, aggregates, which made characterization more difficult. Cross-linking was performed under UV illumination in the presence of a coumarin-bearing cross-linker based on polymethacrylate derivatives. Addition of the photo-cross-linker and cross-linking resulted in better-defined objects with improved stability in most cases.

Due to its intrinsic electrical conductivity, polyaniline (PANI) is one of the most promising conducting polymers for high-performance applications in a wide range of technological fields. However, its poor dispersibility in water and organic solvents markedly imparts its processability and electrical conductivity. Herein, we report a green and one-step approach to preparing stable colloidal dispersions of highly dispersible hybrid nanoparticles by polymerizing PANI onto chitin nanocrystals (ChNCs) as biotemplates, via initiation through the surface amino groups of ChNCs. Evidence of the grafting of PANI onto ChNCs was supported by transmission electron microscopy (TEM), as well as Raman and Fourier transform infrared (FTIR) spectroscopies. Nanocomposite films were prepared by mixing the PANI- g -ChNCs with a waterborne poly(vinyl acetate) latex dispersion followed by casting and film formation at room temperature. The mechanical properties were tested as a function of the PANI- g -ChNC content. In addition, it was shown that at a proper content of PANI in ChNCs, and over a critical loading in the PANI- g -ChNCs, a conductive film was obtained, without sacrificing the reinforcing effect of the rodlike nanofiller. As a potential application, conductive waterborne adhesives for wood were prepared and the performance of the adhesives was tested. This research provides a facile route to fabricating a new class of hybrid nanofiller from a biobased origin, stable in water and easy to mix with waterborne dispersions, combining the merits of the ChNC nanofiller with the conductivity of PANI.

Stable biobased waterborne Pickering dispersions of acrylated epoxidized soybean oil (AESO) were developed using chitin nanocrystals (ChNCs) as sole emulsifier without any additives. Thin AESO-ChNC nanocomposite films were produced by UV-curing thin-coated layers of the AESO emulsion after water evaporation. The kinetics of photopolymerization were assessed by monitoring the consumption of the AESO acrylate groups by infrared spectroscopy (Fourier transform infrared (FTIR)). The curing was faster in the presence of ChNCs, with a disappearance of the induction period observed for neat AESO. The coating of AESO droplets with a thin layer of ChNCs was confirmed by scanning electron microscopy (SEM) observation. SEM and transmission electron microscopy (TEM) images revealed the honeycomb organization of ChNCs inside the cured AESO-ChNC films. The mechanical, thermal, and optical properties of the nanocomposite films were studied by dynamic mechanical analysis (DMA), tensile testing, differential scanning calorimetry (DSC), and transmittance measurement, as a function of ChNC content. The inclusion of ChNCs is strongly beneficial to increase the stiffness and strength of the cured films, without compromising its optical transparency. The ability of ChNCs to act as an emulsifier for AESO in replacement of synthetic surfactants and their strong reinforcing effect in UV-cured films offer new opportunities to produce waterborne stable dispersions from AESO for application in biobased coatings and adhesives.

We present here the grafting of thermoresponsive polyetheramines at the reducing ends of cellulose nanocrystals (CNCs) using a two-step protocol involving an end carboxylation followed by a peptide coupling with the primary amine moiety of the polyetheramine. In aqueous suspensions these end-modified CNCs became associated by their derivatized tips when the temperature was raised past a lower critical solution temperature (LCST), above which these polyetheramines are known to collapse and become hydrophobic. The CNC association was reversible when the temperature was lowered and the phenomenon of association/disassociation was totally reproducible in repeated temperature cycles as followed by dynamic light scattering (DLS). Small-angle neutron scattering (SANS) data revealed the presence of grafted chains with an extended conformation and showed the assembly of modified CNCs into swollen aggregates in suspension at T > LCST. Transmission electron microscopy (TEM) images confirmed that the once dispersed derivatized CNCs at low temperature became associated through their reducing ends above the LCST. At such temperatures, these modified CNCs attached themselves in a remarkable fashion, forming the arms of regular four-, five-, or six-branched stars.

In vitro polymerization of β-mannans is a challenging reaction due to the steric hindrance confered by the configuration of mannosyl residues and the thermodynamic instability of the β-anomer. Whatever the approach used to date-whether chemical, or enzymatic with glycosynthases and mannosyltransferases-pure β-1,4-mannans have never been synthesized in vitro. This has limited attempts to investigate their role in the production of plant and algal cell walls, in which they are highly abundant. It has also impeded the exploitation of their properties as biosourced materials. In this paper, we demonstrate that TM1225, a thermoactive glycoside phosphorylase from the hyperthermophile species Thermotoga maritima, is a powerful biocatalytic tool for the ecofriendly synthesis of pure β-1,4-mannan. The recombinant production of this enzyme and its biochemical characterization allowed us to prove that it catalyzes the reversible phosphorolysis of β-1,4-mannosides, and determine its role in the metabolism of the algal mannans on which T. maritima feeds in submarine sediments. Furthermore, after optimizing the reaction conditions, we exploited the synthetic ability of TM1225 to produce β-1,4-mannan in vitro. At 60 °C and from d-mannose 1-phosphate and mannohexaose, the enzyme synthesized mannoside chains with a degree of polymerization up to 16, which precipitated into lamellar single crystals. The X-ray powder diffraction and base-plane electron diffraction patterns of the lamellar crystals unambiguously show that the synthesized product belongs to the mannan I family previously observed in planta in pure linear mannans, such as those of the ivory nut. The in vitro formation of these mannan I crystals is likely determined by the high reaction temperature and the narrow chain length distribution of the insoluble chains.

The periodate oxidation of microfibrillated cellulose followed by a reduction treatment was implemented to produce a new type of sterically stabilized cellulosic nanocrystals, which were characterized at the molecular and colloidal length scales. Solid-state NMR data showed that these treatments led to objects consisting of native cellulose and flexible polyols resulting from the oxidation and subsequent reduction of cellulose. A consistent set of data from dynamic light scattering, turbidimetry, transmission electron microscopy, and small-angle X-ray scattering experiments further showed that stable neutral elongated nanoparticles composed of a crystalline cellulosic core surrounded by a shell of dangling polyol chains were produced. The dimensions of these biosourced nanocrystals could be controlled by the degree of oxidation of the parent dialdehyde cellulose sample. The purely steric origin of the colloidal stability of these nanoparticles is a strong asset for their use under conditions where electrostatics no longer provides colloidal stability.

The inline coupling of the field-amplified sample injection (FASI) to Taylor dispersion analysis (TDA) was used to characterize low-UV absorbing carboxylated silica nanoparticles (cNPs). The hydrodynamic diameters (D h ) were measured by using a commercial capillary electrophoresis instrument. The proposed methodology did not require any complicated instruments or chromophoric dye to increase the detection sensitivity. A practical method based on a half-Gaussian fitting was proposed for the data processing. The results obtained by this method were compared with those derived from dynamic light scattering (DLS) and transmission electron microscopy (TEM) analyses. From these results, it appeared that the size derived by TDA is in excellent agreement with those measured by DLS and TEM, as demonstrated by stable nanoparticles with narrow size distributions. Intermediate precision relative standard deviations less than 5% were obtained by FASI-TDA. The effect of the FASI-induced cNP peak dispersion on the reliability of the results was discussed in detail.

The interaction of 1,2 dioleolyl-sn-glycero-3-phosphatidylcholine (DOPC) vesicles with cellulose nanocrystals (CNCs) using several complementary techniques. Dynamic light scattering, zeta-potential, cryo-transmission electron microscopy and isothermal titration calorimetry (ITC) analyses confirmed the formation of pH-dependent CNC-liposome complexes. ITC was used to characterize the thermodynamic properties of this interaction. Positive values of enthalpy were found at pH lower than 5 where the charge sign of the constituents was opposite. The association was more pronounced at lower pH, as indicated by the higher values of association constant. We suggest that the positive enthalpy is derived from the release of counterions from the particle hydration shell during the association and that the charge of the vesicles plays a significant role in this interaction.

A series of β-cyclodextrin (βCD) amphiphilic derivatives with varying degrees of substitution were prepared by acylating βCDs on their secondary face using thermolysin to catalyze the transesterification. After dissolution in acetone, the βCD-C n derivatives (n = 8, 10, 12, 14) were nanoprecipitated in water, where they self-organized into structured particles that were characterized using cryo-transmission electron microscopy (cryo-TEM) images and small-angle X-ray scattering (SAXS) data. Two types of morphologies and ultrastructures were observed depending on the total degree of substitution (TDS) of the parent derivative. The molecules with TDS < 5 formed nanospheres with a multilamellar organization, whereas those with TDS > 5 self-assembled into barrel-like (n = 8, 10, 12) or more tortuous (n = 14) particles with a columnar inverse hexagonal structure. In particular, faceted βCD-C 14 particles (TDS = 7) appeared to be composed of several domains with different orientations that were separated by sharp interfaces. Ultrastructural models were proposed on the basis of cryo-TEM images and the analysis of the contrast distribution in different projections of the lattice. Complementary compression isotherm experiments carried out at the air-water interface also suggested that differences in the molecular conformation of the series of derivatives existed depending on whether TDS was lower or higher than 5.

The colloidal stability together with the tunable aggregation and viscoelastic properties of thermoresponsive polymer-grafted cellulose nanocrystals (CNCs) were investigated. TEMPO oxidation of CNCs followed by peptidic coupling in water were used to covalently graft thermosensitive Jeffamine polyetheramine M2005 chains onto the surface of CNCs. The resulting polymer-decorated particles (M2005-g-CNCs) exhibited new colloidal properties, by their ability to perfectly redisperse in water and organic solvents such as toluene, dichloromethane or DMF after freeze-drying. In addition, they presented an enhanced thermal stability when compared to that of sulfated or TEMPO-oxidized CNCs. Dynamic light scattering experiments were used to demonstrate that the thermally induced aggregation of M2005-g-CNCs was fully reversible and reproducible over many temperature cycles and that, most interestingly, the aggregation number could be tuned by varying the ionic strength and/or the pH of the medium, making the suspension multiresponsive. This property arises from the variations of the sign (attractive or repulsive) and the range of the different types (entropic, electrostatic, hydrophobic) of interaction forces between the thermosensitive polymer-decorated nanoparticles. The variation of the viscoelastic properties of M2005-g-CNCs suspensions as a function of temperature, probed by oscillatory rheology measurements of more concentrated suspensions, revealed a reversible temperature-triggered liquid-to-gel transition. Such enhanced functionalities pave the way to the design of advanced CNC-based materials benefiting both from the intrinsic characteristics of these biosourced particles and the new properties imparted by the stimuli-sensitive grafted chains.

Starch derivatives, such as starch-esters, are commonly used as alternatives to pure starch due to their enhanced mechanical properties. However, simple and efficient processing routes are still being sought out. In the present article, we report on a straightforward method for electrospinning high-amylose starch-formate nanofibers from 17 wt % aqueous formic acid (FA) dispersions. The diameter of the electrospun starch-formate fibers ranged from 80 to 300 nm. The electrospinnability window between starch gelatinization and phase separation was determined using optical microscopy and rheological studies. This window was shown to strongly depend on the water content in the FA dispersions. While pure FA rapidly gelatinized starch, yielding solutions suitable for electrospinning within a few hours at room temperature, the presence of water (80 and 90 vol % FA) significantly delayed gelatinization and dissolution, which deteriorated fiber quality. A complete destabilization of the electrospinning process was observed in 70 vol % FA dispersions. Optical micrographs showed that FA induced a disruption of starch granule with a loss of crystallinity confirmed by X-ray diffraction. As a result, starch fiber mats exhibited a higher elongation at break when compared to brittle starch films.

The present paper discusses the controlled self-assembly of sugar-containing block copolymer, maltoheptaose-block-polystyrene (MH(1.2k)-b-PS(4.5k)), into micellar nanoparticles of ca. 30 nm radius in aqueous media and their possibility of gold encapsulation. Micellar association of MH(1.2k)-b-PS(4.5k) into nanoparticles was demonstrated by mixing a large amount of water (MH-selective solvent) with a solution of MH(1.2k)-b-PS(4.5k) in a mixture of tetrahydrofuran (THF) (PS-selective solvent) and water with a certain weight fraction [4:1 (w/w) THF/water], where MH(1.2k)-b-PS(4.5k) exists as well-swollen single chains, followed by evaporation of THF. The mean hydrodynamic radii (Rh) of the nanoparticles were determined by dynamic light scattering (DLS) to be ca. 30 and 80 nm depending upon the method of preparation. The resulting nanoparticles were clearly visualized by transmission electron microscopy (TEM), atomic force microscopy (AFM), and field emission gun-scanning electron microscopy (FEG-SEM) imaging and complemented by nanoparticle tracking analysis (NTA) using a NanoSight instrument. The preliminary study of the self-assembly of MH(1.2k)-b-PS(4.5k) in the presence of gold nanoparticles functionalized with PS chains grafted on their surface indicated potential possibilities of encapsulation of gold nanoparticles into the block copolymer nanoparticles in aqueous media.

Glycogen biosynthesis requires the coordinated action of elongating and branching enzymes, of which the synergetic action is still not clearly understood. We have designed an experimental plan to develop and fully exploit a biomimetic system reproducing in vitro the activities involved in the formation of α(1,4) and α(1,6) glycosidic linkages during glycogen biosynthesis. This method is based on the use of two bacterial transglucosidases, the amylosucrase from Neisseria polysaccharea and the branching enzyme from Rhodothermus obamensis . The α-glucans synthesized from sucrose, a low cost agroresource, by the tandem action of the two enzymes, have been characterized by using complementary enzymatic, chromatographic, and imaging techniques. In a single step, linear and branched α-glucans were obtained, whose proportions, morphology, molar mass, and branching degree depended on both the initial sucrose concentration and the ratio between elongating and branching enzymes. In particular, spherical hyperbranched α-glucans with a controlled mean diameter (ranging from 10 to 150 nm), branching degree (from 10 to 13%), and weight-average molar mass (3.7 × 10(6) to 4.4 × 10(7) g.mol(-1)) were synthesized. Despite their structure, which is similar to that of natural glycogens, the mechanisms involved in their in vitro synthesis appeared to be different from those involved in the biosynthesis of native hyperbranched α-glucans.

The impact of including hydrophobically modified silica on the morphology of miniemulsified monomer mixtures and that of the resulting polymer particles was investigated, with emphasis placed on the distribution and localization of the inorganic phase. Silica nanoparticles with diameters of 20 and 78 nm were first modified with γ-methacryloxypropyl trimethoxysilane (γ-MPS) to favor their dispersion in methyl methacrylate (MMA)/n-butyl acrylate (BuA) and mixtures of varying MMA to BuA weight ratios. The monomer-silica dispersions were then emulsified by ultrasonication, and the resulting silica-loaded droplets were examined using cryo-transmission electron microscopy (cryo-TEM). This represents the first time such silica-loaded nanodroplets were examined in this way. The results of the cryo-TEM show that whereas the silica particles could easily be dispersed in MMA or a mixture of MMA and BuA to produce stable dispersions, the emulsification step promotes the (re)localization of the silica at the oil-water interfaces. It was also shown that not all droplets are equal; some droplets and particles contain no silica whereas others contain many silica particles. After the subsequent polymerization step, the silica was buried inside the latex particles., (© 2012 American Chemical Society)

Stable methyl methacrylate (MMA) miniemulsions were successfully prepared using for the first time cerium oxide (CeO(2)) nanoparticles as solid stabilizers in the absence of any molecular surfactant. The interaction between MMA droplets and CeO(2) nanoparticles was induced by the use of methacrylic acid (MAA) as a comonomer. Both MAA and CeO(2) contents played a key role on the diameter and the stability of the droplets formed during the emulsification step. Cryo-transmission electron microscopy (TEM) images of the suspensions formed with 35 wt % of CeO(2) showed the presence of polydisperse 50-150 nm spherical droplets. More surprisingly, some nonspherical (likely discoidal) objects that could be the result of the sonication step were also observed. The subsequent polymerization of these Pickering miniemulsion droplets led to the formation of composite PMMA latex particles armored with CeO(2). In all cases, the conversion was limited to ca. 85%, concomitant with a loss of stability of the latex for CeO(2) contents lower than 35 wt %. This stability issues were likely related to the screening of the cationic charges present on CeO(2) nanoparticles upon polymerization. TEM images showed mostly spherical particles with a diameter ranging from 100 to 400 nm and homogeneously covered with CeO(2). Besides, for particles typically larger than 200 nm, a buckled morphology was observed supporting the presence of residual monomer at the end of the polymerization and consistent with the limited conversion. The versatility of these systems was further demonstrated using 35 wt % of CeO(2) and replacing MMA by n-butyl acrylate (BA) either alone or in combination with MMA. Stable monomer emulsions were always obtained, with the droplet size increasing with the hydrophobicity of the oil phase, pointing out the key influence of the wettability of the solid stabilizer. The polymerization of Pickering miniemulsion stabilized by CeO(2) nanoparticles proved to be an efficient strategy to form armored composite latex particles which may find applications in coating technology., (© 2012 American Chemical Society)

Agarose hydrogels filled with cellulose nanowhiskers were strained in uniaxial stretching under different humidity conditions. The orientation of the cellulose whiskers was examined before and after testing with an X-ray laboratory source and monitored in situ during loading by synchrotron X-ray diffraction. The aim of this approach was to determine the process parameters for reorienting the cellulose nanowhiskers toward a preferential direction. Results show that a controlled drying of the hydrogel is essential to establish interactions between the matrix and the cellulose nanowhiskers which allow for a stress transfer during stretching and thereby promote their alignment. Rewetting of the sample after reorientation of the cellulose nanowhiskers circumvents a critical increase of stress. This improves the extensibility of the hydrogel and is accompanied by a further moderate alignment of the cellulose nanowhiskers. Following this protocol, cellulose nanowhiskers with an initial random distribution can be reoriented toward a preferential direction, creating anisotropic nanocomposites.

The behavior of β-lactoglobulin (β-Lg) during heat treatments depends on the environmental conditions. The influence of the presence or absence of a reducing sugar, namely, glucose, on the modification of the protein during heating has been studied using fluorescence, polyacrylamide gel electrophoresis (PAGE), size-exclusion chromatography (SEC), and transmission electron microscopy. Glycated products were formed during heating 24 h at 90 °C and pH 7. The fluorescence results revealed an accumulation of the advanced Maillard products and the formation of aggregates during heating. PAGE and SEC data suggested that the products in the control samples were essentially composed of covalently linked fibrillar aggregates and that their formation was faster than that for glycated samples. We showed that glucose affected the growing step of covalent aggregates but not the initial denaturation/aggregation step of native protein. Glucose-modified proteins formed a mixture of short fibrils and polydisperse aggregates. Our results revealed that β-Lg forms fibrils at neutral pH after heating and that glucose slows the formation of these fibrils.

Nanoparticles of amphiphilic α-, β-, and γ-cyclodextrins were obtained by formulation of cyclodextrins enzymatically transesterified with vinyl decanoate. The product of this synthesis is a mixture of bioesterified cyclodextrins with various degrees of substitution (DS) presenting for a same DS different regio-isomers. In a first step, the efficiency of a MALDI-TOF procedure to characterize the average molecular weight of the derivative bulk mixture was demonstrated by comparing the results with those obtained from complementary NMR and HPLC techniques. In a second step, the ultrastructure of nanoparticles prepared from three different batches of synthesis was investigated and correlated with the average molecular weight and DS of the parent derivative.

The grafting of thermosensitive amine-terminated statistical polymers onto the surface of cellulose nanocrystals (CNCs) was achieved by a peptidic coupling reaction, leading to unusual properties like colloidal stability at high ionic strength, surface activity, and thermoreversible aggregation. We have used a large variety of experimental techniques to investigate the properties of the polymer-decorated CNCs at different length-scales and as a function of the different reaction parameters. A high grafting density could be obtained when the reaction was performed in DMF rather than water. Infrared and solid-state NMR spectroscopy data unambiguously demonstrated the covalent character of the bonding between the CNCs and the macromolecules, whereas TEM images showed a preserved individualized character of the modified objects. Dynamic light scattering and zeta potential measurements were also consistent with individual nanocrystals decorated by a shell of polymer chains. Surface tension measurements revealed that CNCs became surface-active after the grafting of thermosensitive amines. Decorated CNCs were also stable against high electrolyte concentrations. A thermoreversible aggregation was also observed, which paves the way for the design of stimuli-responsive biobased nanocomposite materials.

Model A-type amylose single crystals were prepared by recrystallizing dextrins from acid-hydrolyzed native starch and narrow fractions of short chains of enzymatically synthesized amylose, in dilute water/acetone solutions. In most cases, spindle-shaped crystals with a sharp, round or flat apical end were formed, organized in rosettes or fan-like assemblies. The morphology and crystal size were shown to strongly depend on the average degree of polymerization (DP), distribution width (DW), and degree of branching of the chains. The largest and most clearly faceted single crystals were prepared using fractions of synthetic amylose. Typically, 5-10 μm long crystals were obtained from fractions with 17 ≤ DP ≤ 20 and DW ≤ 8. Chains with DP > 40 and a high polydispersity formed ill-defined networks of smaller crystallites. Fractions of branched and more polydisperse limit dextrins yielded crystals smaller than those obtained from narrow fractions of synthetic amylose. The morphological analysis of faceted single crystals combined with electron diffraction data confirmed that the double helices were oriented along the long dimension of the crystal and packed into lamellae with a parallelogram cross section defined by the a and b directions of the monoclinic unit cell of A-amylose. The lamellae are stacked along the c-axis that is oriented parallel but opposite to the growth direction of the crystal.

The B-->A phase transition in native starch granules and spherocrystals prepared from DP 20-40 synthetic amylose chains was investigated in situ at intermediate moisture content (20-30%) by wide-angle synchrotron X-ray scattering, using a temperature-controlled pressure cell. The transition in native starch was monitored at hydrostatic pressures of 1.6-11.0 MPa and occurred in a temperature range of 90-110 degrees C. The transition temperature increased with increasing amylose content and the transition was incomplete in amylose-rich starch. The B-->A transition in highly crystalline amylose spherocrystals was monitored at pressures between 2.0 and 28.5 MPa. The transition temperature was higher than in native starch, ranging from 125 to 135 degrees C. At 2.0 MPa, after conversion, the hydrated spherocrystals melted at 185 degrees C. Surprisingly, at the same pressure, in excess water, the spherocrystals did not solubilize but converted to allomorph A at 100 degrees C and melted at 160 degrees C. For all samples, the transition occurred in a matter of minutes and a higher pressure decreased the transition temperature. For the first time, thermal expansion coefficients were estimated for A- and B-amylose at intermediate moisture. A strong thermal anisotropy was observed for A-amylose, the expansion being higher along the b-axis than along the a-axis of the monoclinic unit cell. This anisotropy was attributed to the fact that, in the b-direction, amylose double helices lie at the same height along the chain axis while, in the a-direction, they are more closely packed in a zigzag fashion.

Endo-beta-1,4-xylanases (EC 3.2.1.8) are the main enzymes involved in the hydrolysis of xylans, the most abundant hemicelluloses in plant biomass. However, the development of efficient endoxylanases for use in biorefinery processes is currently hampered by insufficient knowledge regarding the impact of the cell wall network organization on the action of the enzyme at the supramolecular level. The action pattern of a GH11 endoxylanase from Thermobacillus xylanilyticus (Tx-xyl) was investigated by means of in vitro reconstituted model systems which can mimic certain cell wall structures. The action of Tx-xyl was evaluated on polymer assemblies displaying increasing complexity using delignified glucuronoarabinoxylan (GAX), then GAX-DHP model complexes obtained by oxidative polymerization of coniferyl alcohol into dehydrogenation polymers (DHP: lignin model compounds) in the presence of GAX. At a high concentration of GAX, interchain associations are formed leading to high molecular weight aggregates. These structures did not appear to affect the action of endoxylanase, which induces disaggregation of the self-aggregates along with polymer depolymerization. To mimic lignin-carbohydrate interactions, two different GAX-DHP nanocomposites were prepared and incubated with endoxylanase. In both cases, free GAX was hydrolyzed, while the GAX-DHP complexes appeared to be resistant. In the case of the noncovalently linked GAX-DHP(ZL) complexes, enzyme action favored a decrease in particle size, owing to the removal of their relatively exposed carbohydrate chains, whereas the complex supramolecular organization of the covalently linked GAX-DHP(ZT) complexes severely hampers the enzyme's access to carbohydrate. Overall, these results establish the negative impact of DHP on the endoxylanase action and provide new knowledge regarding the limitations of the enzyme action in the lignocellulose bioconversion processes.

Cotton cellulose nanocrystals with different aspect ratios have been dispersed in cyclohexane as a model apolar solvent, using surfactants. Above a critical concentration, which was higher than that in water, the suspensions spontaneously phase separated into a chiral nematic mesophase. According to Onsager's theory, the phase separation is controlled by the aspect ratio, while being influenced by the polydispersity. The sample with the highest aspect ratio did not show any phase separation but instead shows an anisotropic gel phase at high concentration. Experimental critical concentrations were found to be much lower than the predicted ones, revealing an attractive interaction between the rods. Chiral nematic pitches as small as 2 mum were found to be much lower than those measured in water, due to stronger chiral interactions in the apolar medium.

We report the synthesis of fully biodegradable polymeric nanoparticles presenting mannose residues at their surface and their interaction with lectins. A simple and versatile method was used to reach the surface functionalization of poly(D,L-lactic acid) (PLA) nanoparticles by mannose moieties: It consists in using an amphiphilic mannosylated poly(ethylene oxide)-b-poly(E-caprolactone) (PEO-b-PCL) diblock copolymer as a bioresorbable surface modifier in a simple nanoprecipitation-evaporation procedure. The size and zeta potential of the nanoparticles were found to depend on the molar copolymer/PLA ratio, demonstrating the influence of the copolymer on the formation of the nanoparticles. The bioavailability of the mannose residues as specific recognition sites on the nanoparticle surface could be demonstrated by a modified enzyme-linked lectin assay (ELLA) using biotin-labeled lectins which interact specifically with alpha-D-mannopyrannoside derivatives. Besides specific interaction by lectin-mannose complex formation, nonspecific adsorption of the proteins on the nanoparticle surface was observed. These results were fully supported by isothermal titration calorimetry experiments which suggested that the balance between specific and nonspecific interactions can be controlled by the amount of glycosylated polymer used for the preparation of the nanoparticles. Such nanoparticles are expected to be specifically recognized by mannose receptors, which are highly expressed in cells of the immune system. The targeting properties of these carrier systems combined with their potential adjuvant effects due to their size in the range of 200-300 nm make them attractive candidates as vaccine delivery systems.

The nano-organized LipoParticle assemblies, consisting of polymer particles coated with lipid layers, are investigated with the aim of evidencing the impact of the particle chemical nature on their physicochemical behavior. To this end, these colloidal systems are elaborated from anionic submicrometer poly(styrene) (P(St)) or poly(lactic acid) (PLA) particles, and lipid mixtures composed of zwitterionic 1,2-dipalmitoyl- sn-glycero-3-phosphocholine (DPPC) and cationic 1,2-dipalmitoyl-3-trimethylammonium-propane (DPTAP). As revealed by various experimental techniques, such as quasielastic light scattering, zeta potential measurements, transmission electron microscopy, and 1H NMR spectroscopy, the features of both LipoParticle systems are similar when cationic lipid formulations (DPPC/DPTAP mixtures) are used. This result emphasizes the major role of electrostatic interactions as driving forces in the assembly elaboration process. Conversely, the assemblies prepared only with the zwitterionic DPPC lipid are strongly dependent on the particle chemical nature. The structural characteristics of the assemblies based on PLA particles are not controlled and correspond to aggregates, contrary to P(St) particles. To understand this specific phenomenon, and to consequently improve the final organization of these assemblies which are potentially of great interest in biotechnology and biomedicine, numerous investigations are carried out such as the studies of the impact of the ionic strength and the pH of the preparation media, as well as the presence of ethanol (involved in the PLA particle synthesis) or the mean size of the lipid vesicles. From the resulting data and according to the nature of spherical solid support, hydrophobic effects, hydrogen bonds, or dipole-dipole interactions would also appear to influence the LipoParticle elaboration in the case of zwitterionic lipid formulation.

The shape and size distribution of crystalline nanoparticles resulting from the sulfuric acid hydrolysis of cellulose from cotton, Avicel, and tunicate were investigated using transmission electron microscopy (TEM) and atomic force microscopy (AFM) as well as small- and wide-angle X-ray scattering (SAXS and WAXS). Images of negatively stained and cryo-TEM specimens showed that the majority of cellulose particles were flat objects constituted by elementary crystallites whose lateral adhesion was resistant against hydrolysis and sonication treatments. Moreover, tunicin whiskers were described as twisted ribbons with an estimated pitch of 2.4-3.2 microm. Length and width distributions of all samples were generally well described by log-normal functions, with the exception of tunicin, which had less lateral aggregation. AFM observation confirmed that the thickness of the nanocrystals was almost constant for a given origin and corresponded to the crystallite size measured from peak broadening in WAXS spectra. Experimental SAXS profiles were numerically simulated, combining the dimensions and size distribution functions determined by the various techniques.

A novel bioeliminable amphiphilic poly(ethylene oxide)-b-poly(epsilon-caprolactone) (PEO-b-PCL) diblock copolymer end-capped by a mannose residue was synthesized by sequential controlled polymerization of ethylene oxide and epsilon-caprolactone, followed by the coupling of a reactive mannose derivative to the PEO chain end. The anionic polymerization of ethylene oxide was first initiated by potassium 2-dimethylaminoethanolate. The ring-opening polymerization of epsilon-caprolactone was then initiated by the omega-hydroxy end-group of PEO previously converted into an Al alkoxide. Finally, the saccharidic end-group was attached by quaternization of the tertiary amine alpha-end-group of the PEO-b-PCL with a brominated mannose derivative. The copolymer was fully characterized in terms of chemical composition and purity by high-resolution NMR spectroscopy and size exclusion chromatography. Furthermore, measurements with a pendant drop tensiometer showed that both the mannosylated copolymer and the non-mannosylated counterpart significantly decreased the dichloromethane/water interfacial tension. Moreover, these amphiphilic copolymers formed monodisperse spherical micelles in water with an average diameter of approximately 11 nm as measured by dynamic light scattering and cryo-transmission electron microscopy. The availability of mannose as a specific recognition site at the surface of the micelles was proved by isothermal titration microcalorimetry (ITC), using the BclA lectin (from Burkholderia cenocepacia), which interacts selectively with alpha-D-mannopyranoside derivatives. The thermodynamic parameters of the lectin/mannose interaction were extracted from the ITC data. These colloidal systems have great potential for drug targeting and vaccine delivery systems.

Lamellar square single crystals of V-amylose were obtained by adding alpha-naphthol to metastable dilute aqueous solutions of synthetic amylose chains with an average degree of polymerization of 100. The morphology and structure of the crystals were studied using low-dose transmission electron microscopy including high-resolution imaging, as well as electron and X-ray diffraction. The crystals are crystallized in a tetragonal P4(1)2(1)2 or P4(3)2(1)2 space group with unit cell parameters, calculated from X-ray diffraction data, a = b = 2.2844 nm (+/-0.0005) and c = 0.7806 nm (+/-0.001), implying the presence of two amylose chains per unit cell. High-resolution lattice images of the crystals confirmed that the amylose chains were crystallized as 8-fold helices corresponding to the repeat of four maltosyl units.

Coniferyl alcohol (G monomer) and a mixture of coniferyl alcohol/sinapyl alcohol (GS monomers, 1/1 ratio) were polymerized to dehydrogenation polymers (DHPs) in presence of two structurally related heteroxylans (HX) differing only in their phenolic substitution patterns. One (HX-40) was enriched in ferulate (FA) while the other (HX-90) was almost devoid of FA. The morphology of the resulting nanoparticles was studied by transmission electron microscopy whereas formation of particles was followed by size exclusion chromatography with online multiangle laser light scattering. HX-40-DHP-G- and HX-40-DHP-GS-derived particles display complex morphological patterns whereas HX-90-DHP-G and HX-90-DHP-GS present rather spherical shapes. The determination of particle sizes and molar masses showed that HX-90 samples formed denser particles than HX-40 ones. These differences are discussed in relation to the ferulate substitution level.

The recombinant amylosucrase from Neisseria polysaccharea was used to glucosylate glycogen particles in vitro in the presence of sucrose as the glucosyl donor. The morphology and structure of the resulting insoluble products were shown to strongly depend on the initial sucrose/glycogen weight ratio. For the lower ratio (1.14), all glucose molecules produced from sucrose were transferred onto glycogen, yielding a slight elongation of the external chains and their organization into small crystallites at the surface of the glycogen particles. With a high initial sucrose/glycogen ratio (342), the external glycogen chains were extended by amylosucrase, yielding dendritic nanoparticles with a diameter 4-5 times that of the initial particle. A partial crystallization of the elongated chains induced a "shrinkage" of the nanospheres. The synthesis of linear alpha-(1,4) chains occurred simultaneously, yielding semicrystalline fibrous entities. All products displayed a B-type crystal structure. The kinetics of chain elongation and aggregation were thoroughly investigated in order to explain how the action of amylosucrase resulted in such different structures. These results emphasize the potentiality of amylosucrase in the design of original carbohydrate-based dendritic nanoparticles.

Never-dried native celluloses (bleached sulfite wood pulp, cotton, tunicin, and bacterial cellulose) were disintegrated into individual microfibrils after oxidation mediated by the 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) radical followed by a homogenizing mechanical treatment. When oxidized with 3.6 mmol of NaClO per gram of cellulose, almost the totality of sulfite wood pulp and cotton were readily disintegrated into long individual microfibrils by a treatment with a Waring Blendor, yielding transparent and highly viscous suspensions. When observed by transmission electron microscopy, the wood pulp and cotton microfibrils exhibited a regular width of 3-5 nm. Tunicin and bacterial cellulose could be disintegrated by sonication. A bulk degree of oxidation of about 0.2 per one anhydroglucose unit of cellulose was necessary for a smooth disintegration of sulfite wood pulp, whereas only small amounts of independent microfibrils were obtained at lower oxidation levels. This limiting degree of oxidation decreased in the following order: sulfite wood pulp > cotton > bacterial cellulose, tunicin.

Native cellulose has been oriented in an ac electric field at both the macroscopic and colloidal level. Ramie fiber fragments suspended in chloroform have been shown to point along the field. Cellulose microcrystal suspensions in cyclohexane have also been allowed to evaporate in an electric field and have exhibited a high degree of orientation when further examined by TEM and electron diffraction. Similarly, cellulose whisker suspensions showed increasing birefringence with increasing field strength and displayed interference Newton colors that saturated at around 2000 V cm(-)(1). A high degree of order of this suspension was also obtained by evaluating the induced birefringence with color charts.

The synthesis of decanoate beta-cyclodextrin esters (beta-CDd) and hexanoate beta-cyclodextrin esters (beta-CDh) was biocatalyzed by thermolysin from native beta-cyclodextrin (beta-CD) and vinyl hexanoate or vinyl decanoate used as acyl donors. The products were chemically characterized by infrared, NMR, and mass spectrometry. Both beta-CDd and beta-CDh esters were identified as a mixture of beta-CD preferentially substituted on the C2 position by the corresponding acyl chain. The degree of substitution varied from 2 to 7 for beta-CDd and from 4 to 8 for beta-CDh. The ability of beta-CD esters to self-organize into nanoparticles was tested using a nanoprecipitation technique in various solvents. The mean size diameter and polydispersity measured by quasi-elastic light scattering were dramatically affected by the nature of solvent (acetone, ethanol, or tetrahydrofuran) used in the nanoprecipitation technique. When directly observed using cryo-transmission electron microscopy, beta-CDh appeared as uniformly dense nanospheres, whereas beta-CDd exhibited a multilamellar onion-like organization. A structural model was rationalized for the beta-CDd nanoparticles.

The morphology of micelles formed from blends of linear and cyclic poly(styrene-b-isoprene) (PS-b-PI) block copolymers has been investigated in solution using dynamic light scattering (DLS) and in thin solid deposits by atomic force microscopy (AFM) and transmission electron microscopy under cryogenic conditions (cryo-TEM). Micelles of the pure cyclic PS(290)-b-PI(110) copolymers are wormlike cylindrical objects built by unidirectional aggregation of 33 nm wide sunflower micelles, while the linear block copolymer having the same volume fraction and molar mass forms spherical micelles 40 nm in diameter. The DLS, AFM, and cryo-TEM results consistently show that the addition of the linear copolymer (even for amounts as low as 5% w/w) to the cyclic copolymer rather favors the formation of spherical micelles at the expense of the cylindrical aggregates. Those results clearly show that the linear block copolymer chains can be used to stabilize the thermodynamically unstable elementary sunflower micelle. The thermal stability of the micelles (from the pure copolymers and from the blends) has been examined in solid deposits with in situ AFM measurements. Coalescence starts at about 70 degrees C, and the surface roughness shows a two-step decrease toward a fully homogeneous and flat structure.

The synthesis, characteristics, and properties of amphipatic, water-soluble dendrigrafts, with a polystyrene core and polystyrene-b-poly(methyl vinyl ether) (PS-b-PMVE) diblock as external branches, are described. The dendrigrafts are observed by AFM and TEM as egglike or long cylindrical objects which can self-organize intramolecularly in segregated subdomains forming flowerlike or strings of flowerlike objects. In organic solvents the dendrigrafts behave as fully soluble isolated macromolecules and show in water a low critical solubility temperature (LCST) at t > 30 degrees C. The ability of the amphiphilic PS-b-PMVE dendrigrafts to complex and transport in water organic (pyrene) and metallo-organic (manganese tetraphenyl porphyrin) molecules is investigated. The possibility to stabilize the high oxidation state of metallo-porphyrin complexes through their encapsulation into the dendrigraft is shown.

The recombinant amylosucrase from Neisseria polysaccharea was used to synthesize in vitro amylose from sucrose as unique substrate. The morphology and structure of the insoluble residue were shown to depend only on the initial sucrose concentration (100, 300, or 600 mM), which controlled both the chain length and concentration at the precipitation stage. The average degree of polymerization (DP) in the precipitated product varied from 58 for the lowest initial sucrose concentration (100 mM) to 45 and 35 for higher sucrose concentrations (300 and 600 mM, respectively). The shorter chains (DP 35 and 45), produced in high yields (54 and 24 g/L respectively), precipitated as polycrystalline aggregates with exceptional crystallinity, without optimization of the reaction medium for crystallization. The longer chains (DP 58), produced in lower amount (2.9 g/L), formed networks similar to those observed for amylose gels. All synthesized products displayed a B-type crystal structure. Their melting behavior was also studied, the thermostability being higher for the precipitate containing the longer chains. Further thermal treatments were shown to still improve the crystallinity and yield substrates usable as new standards for the determination of the relative crystallinity of starchy products. The kinetics of chain elongation and aggregation were thoroughly investigated in order to explain how the action of amylosucrase resulted in such different amylose structures. These results emphasize the potentiality of amylosucrase in the design of amylodextrins with controlled morphology, structure, and physicochemical properties.

A series of samples having the mannan II character were prepared by either (i) desincrusting stems of Acetabularia crenulata, or (ii) acetylating these stems, followed by dissolution and recrystallization under deacetylation conditions, or (iii) recrystallizing at low temperature the alkali soluble fraction of ivory nut mannan. The samples were characterized by transmission electron microscopy, X-ray and electron diffraction analysis together with (13)C CP/MAS NMR spectroscopy. Whereas the A. crenulata stems consisted of a mixture of mannan I and mannan II, the recrystallized samples were all of the hydrated mannan II family and occurred in a ribbonlike morphology where the mannan chains were organized with their molecular axis perpendicular to the ribbon long axis. The recrystallized ivory nut mannan samples presented X-ray and electron diffraction diagrams, together with (13)C solid-state NMR spectra recorded at 95% RH, different from those of recrystallized A. crenulata recorded under the same RH conditions. They corresponded therefore to a new allomorph of the mannan II family. Despite this difference, when the recrystallized samples were in an aqueous environment, they revealed an additional well-defined perhydrated phase, which showed the same (13)C solid-state NMR spectrum for both samples. As this phase, which gave 6-band NMR spectra with narrow line-width and low T1, had no counterpart in X-ray diffraction, it was attributed to specific amorphous segments of mannan chains, gaining some mobility when swollen in water. When the samples were totally dried, their NMR spectra lost their resolution, thus indicating the role played by water for the structural organization of the crystalline and amorphous components of mannan II.

Debranching and crystallization occurring during the enzymatic treatment of 25% (w/v) aqueous solutions of maltodextrins by isoamylase at 52 degrees C were studied. The morphology as well as the crystal and molecular structures of the precipitates formed at different stages of the reaction were characterized. Two types of resulting products, differing in terms of structure and morphology, were evidenced. A loose B-type network, containing linear and branched chains of highest molecular weight, was mainly formed during the first 12 h of reaction, whereas aggregates of A-type lamellar crystals, made of short linear chains, were predominantly obtained between 12 and 48 h. The aggregation behavior as a function of temperature and molecular weight distribution of such substrates was discussed and compared to that of related starch products.

The detailed ultrastructure of a new type of resistant starch and the way that it is modified during hydrolysis by alpha-amylases were studied by transmission electron microscopy (TEM) on model starch crystals. The selected substrates were waxy maize starch lintners and A-type crystals prepared from low degree of polymerization (DP) amylose. A model describing the stacking of double helices is proposed for A-type low DP amylose crystals. The enzymatic hydrolysis of both lintners and low DP crystals has been shown to occur by the side of double helices and not their ends. The results were transposed to a new type of resistant starch (RS) produced by debranching maltodextrins in concentrated solutions. This product presents A-type crystallinity contrary to all other known classified RS. Moreover it consists of low DP chains similar to the model crystals studied and yields similar electron diffraction patterns to those of A-type low DP crystals. The similarities in the morphology of these substrates with that of the studied RS led us to attribute its resistance to its particularly dense and compact morphology, resulting from the epitaxial growth of elementary crystalline A-type platelets. In the resulting structure, the accessibility of double helices to alpha-amylase is strongly reduced by aggregation.

Colloidal aqueous suspensions of starch nanocrystals were prepared by submitting native granules from A-type amylopectin-rich waxy maize to a hydrochloric acid hydrolysis. The insoluble residue contains polydisperse and more or less individualized platelet nanocrystals corresponding to the lamellae formed by the association of amylopectin side branches into parallel arrays of double helices. After 2 weeks of hydrolysis, 5-7 nm thick lamellae still connected by alpha(1-->6) linkages were seen edge-on using transmission electron microscopy. As the hydrolysis progressed up to 6 weeks, more alpha(1-->6) branching points located in the inter-lamellar areas were severed and the platelets were thus observed in planar view. Despite a variety of shapes, characteristic geometrical features of the nanocrystalsa were recognized, such as marked 60-65 degrees acute angles and constituting parallelepipedal blocks with a length of 20-40 nm and a width of 15-30 nm. X-ray and electron diffraction showed that these nanoplatelets retain the crystalline A-type of the parent granules.