Search

The global spread of COVID-19 as well as the worsening air pollution throughout the world have brought tremendous attention to the development of materials that can efficiently capture particulate matter. We suggest that the high porosity of electrospun filters composed of nanofibers could provide minimal obstruction to air flow, while their high tortuosity and surface area-to-volume ratio present an excellent platform to capture particulates. In this study, the removal of nanoscale particles via in-house fabricated cellulose nanofilters is significantly enhanced by chemically functionalizing the fibers' surface via the deposition of the bioinspired glue polydopamine (PDA) or the polycation poly(diallyldimethylammonium chloride) (PDADMAC). The effects of filter packing density, layering thickness, and chemistry on their performance, i.e., their filtration efficiency, most penetrating particle size (MPPS), particle fractional penetration percent, and performance in a high relative humidity environment, were investigated. When evaluated in an extremely hazardous environment (PM concentration ∼2000 μg m-3), the filtration efficiency, pressure drop, and quality factor for the cellulose nanofilters were measured to be >98.0%

We designed and synthesized epoxy-encapsulated microparticles with core-shell structures via suspension polymerization to enable high-efficiency, room-temperature cold spray processing. The soft core of the microparticles was comprised of a thermoset resin, diglycidyl ether of bisphenol A (DGEBA), which was optionally blended with the thermoplastic, poly(butyl acrylate); the protective shell was formed using polyurea. The composition, morphology, and thermal behavior of the microparticles were investigated. An inverse relationship between deposition efficiency and particle size was demonstrated by varying the surfactant concentration that was used during particle synthesis. We also determined that the microparticles that had pure resin as the core had the lowest viscosity, exhibited a decrease in the critical impact velocity required for adhesion, had the best flowability, and yielded a dramatic increase in deposition efficiency (56%). We have demonstrated that our in-house synthesized particles can form homogeneous, smooth, and fully coalesced coatings using room-temperature cold spray.

Dysfunction of the intestinal mucus barrier causes disorders such as ulcerative colitis and Crohn’s disease. The function of this essential barrier may be affected by the periodically changing luminal environment. We hypothesized that the pH and ion concentration in mucus control its porosity, molecular permeability, and the penetration of microbes. To test this hypothesis, we developed a scalable method to extract porcine small intestinal mucus (PSIM). The aggregation and porosity of PSIM were determined using rheometry, spectrophotometry, and microscopy. Aggregation of PSIM at low pH increased both the elastic (G′) and viscous (G″) moduli, and it slowed the transmigration of pathogenic Salmonella. Molecular transport was dependent on ion concentration. At moderate concentrations, many microscopic aggregates (2–5 μm in diameter) impeded diffusion. At higher concentrations, PSIM formed aggregate islands, increasing both porosity and diffusion. This in vitro model could lead to a better understanding of mucus barrier functions and improve the treatment of intestinal diseases.

Bacterial attachment and proliferation on surfaces threaten human health and negatively impact the medical, food processing, and marine industries. In this study, we synthetically produced bioinspi...

Electrospun biopolyelectrolyte nanofibers hold potential for use in a range of biomedical applications, but eliminating toxic chemicals involved in their production remains a key challenge. In this study, we successfully electrospun nanofibers from an aqueous complex coacervate solution composed of chitosan and hyaluronic acid. Experimentally, we investigated the effect of added salt and electrospinning apparatus parameters, such as how applied voltage affected fiber formation. We also studied how the addition of alcohol cosolvents affected the properties of the coacervate solution and the resulting nanofibers. Overall, we observed a trade-off in how the addition of salt and alcohol affected the phase behavior and rheology of the coacervates and, consequently, the size of the resulting fibers. While salt served to weaken electrostatic associations within the coacervate and decrease the precursor solution viscosity, the addition of alcohol lowered the dielectric constant of the system and strengthened these interactions. We hypothesize that the optimized concentration of alcohol accelerated the solvent evaporation during the electrospinning process to yield desirable nanofiber morphology. The smallest average nanofiber diameter was determined to be 115 ± 30 nm when coacervate samples were electrospun using an aqueous solvent containing 3 wt % ethanol and an applied voltage of 24 kV. These results demonstrate a potentially scalable strategy to manufacture electrospun nanofibers from biopolymer complex coacervates that eliminate the need for toxic solvents and could enable the use of these materials across a range of biomedical applications.

Antimicrobial biomaterials are critical to aid in the regeneration of oral soft tissue and prevent or treat localised bacterial infections. With the rising trend in antibiotic resistance, there is a pressing clinical need for new antimicrobial chemistries and biomaterial design approaches enabling on-demand activation of antibiotic-free antimicrobial functionality following an infection that are environment-friendly, flexible and commercially-viable. This study explores the feasibility of integrating a bioresorbable electrospun polymer scaffold with localised antimicrobial photodynamic therapy (aPDT) capability. To enable aPDT, we encapsulated a photosensitiser (PS) in polyester fibres in the PS inert state, so that the antibacterial function would be activated on-demand via a visible light source. Fibrous scaffolds were successfully electrospun from FDA-approved polyesters, either poly(epsilon-caprolactone (PCL) or poly[(rac-lactide)-co-glycolide] (PLGA) with encapsulated PS (either methylene blue (MB) or erythrosin B (ER)). The electrospun fibres achieved an ~100 wt.% loading efficiency of PS, which significantly increased their tensile modulus and reduced their average fibre diameter and pore size with respect to PS-free controls. In vitro, PS release varied between a burst release profile to limited release within 100 hours depending on the selected scaffold formulation. Exposure of PS-encapsulated PCL fibres to visible light successfully led to at least a 1 log reduction in E. coli viability after 60 minutes of light exposure whereas PS-free electrospun controls did not inactive microbes. This study successfully demonstrates the significant potential of PS-encapsulated electrospun fibres as photodynamically active biomaterial for antibiotic-free infection control.

Here, we demonstrate the anionic polymerization and the high reactivity of the novel monomer diethyl methylene malonate (DEMM). At room temperature and under atmospheric conditions, water and anionic functional groups (i.e., carboxyl, boronic, and phenol) quickly initiate DEMM. The polymerization of DEMM in water and the final molecular weight of the polymer were both demonstrated to be pH-dependent. Systematically, investigations were conducted to study the conversion rate of DEMM with various functional groups, and the polymerization was verified to occur with anionic groups using a carboxylate-initiated DEMM system. For coating applications, we also investigated a multifunctional derivative monomer called (DEMM)(6) that is an oligomeric polyester of DEMM esterified with butanediol that contains on average six repeat units of reactive DEMM (commercially known as Forza B3000 XP). The incorporation of 15 wt % (DEMM)(6) into latex containing methacrylate acid as a functional monomer yielded cross-linked coatings with a gel content of 76.25 wt % that had a 289% improvement in rub-resistance performance compared to controls (without (DEMM)(6)). This study provides a facile methodology to synthesize cross-linked latex coatings at room temperature.

Surface-associated transport of flowing bacteria, including cell rolling, is a mechanism for otherwise immobile bacteria to migrate on surfaces and could be associated with biofilm formation or the spread of infection. This work demonstrates how the moduli and/or local polymer concentration play critical roles in sustaining contact, dynamic adhesion, and transport of bacterial cells along a hydrogel or hydrated brush surface. In particular, stiffer more concentrated hydrogels and brushes maintained the greatest dynamic contact, still allowing cells to travel along the surface in flow. This study addressed how the mechanical properties, molecular architectures, and thicknesses of minimally adhesive poly(ethylene glycol) (PEG)-based coatings influence the flow-driven surface motion of Staphylococcus aureus MS2 cells. Three protein-repellant PEG-dimethylacrylate hydrogel films (∼100 μm thick) and two protein-repellant PEG brushes (8-16 nm thick) were sufficiently fouling-resistant to prevent the accumulation of flowing bacteria. However, the rolling or hopping-like motions of gently flowing S. aureus cells along the surfaces were specific to the particular hydrogel or brush, distinguishing these coatings in terms of their mechanical properties (with moduli from 2 to 1300 kPa) or local PEG concentrations (in the range 10-50% PEG). On the stiffer hydrogel coatings having higher PEG concentrations, S. aureus exhibited long runs of surface rolling, 20-50 μm in length, an increased tendency of cells to repeatedly return to some surfaces after rolling and escaping, and relatively long integrated contact times. By contrast, on the softer more dilute hydrogels, bacteria tended to encounter the surface for brief periods before escaping without return. The dynamic adhesion and motion signatures of the cells on the two brushes were bracketed by those on the soft and stiff hydrogels, demonstrating that PEG coating thickness was not important in these studies where the vertically oriented surfaces minimized the impact of gravitational forces. Control studies with similarly sized poly(ethylene oxide)-coated rigid spherical microparticles, that also did not arrest on the PEG coatings, established that the bacterial skipping and rolling signatures were specific to the S. aureus cells and not simply diffusive. Dynamic adhesion of the S. aureus cells on the PEG hydrogel surfaces correlated well with quiescent 24 h adhesion studies in the literature, despite the orientation of the flow studies that eliminated the influence of gravity on bacteria-coating normal forces.

Epoxy-based powder coatings are an attractive alternative to solvent-borne coatings. Here, in-house synthesized low glass transition temperature (Tg) particles containing epoxy resin and polymethyl methacrylate formed coatings at room temperature upon impact with a surface. Suspension polymerization was used to prepare particles as a function of diglycidyl ether of bisphenol A (DGEBA) and methyl methacrylate ratios. Higher incorporation of DGEBA decreased the Tg to below ~20°C and eliminated the need to heat the particles and/or aluminum substrates to form coatings. Using an electrostatic powder coating apparatus, a ~70% particle deposition efficiency was achieved on aluminum substrates heated to 200°C. Whereas, at room temperature, high-speed single particle impact experiments proved that particle bonding occurred at a critical velocity of 438 m/s, comparable to commercial cold spray technologies. The in-house synthesized particles used in this study hold potential in traditional and emerging additive manufacturing applications.

We present the first demonstration of the direct encapsulation of cargo into polyelectrolyte complex (PEC) fiber mats. This approach takes advantage of the intrinsic self-assembly characteristics of complex coacervates to simplify the formulation requirements to electrospin fibers containing a high loading and an even distribution of cargo. Two families of structurally similar fluorescent dyes were used as model cargo of varying hydrophobicity and charge and were encapsulated into coacervates of poly(4-styrenesulfonic acid, sodium salt) and poly(diallyldimethylammonium chloride). The coacervate phase behavior, dye partitioning, and resulting fibers were systematically investigated as a function of dye and salt concentration. Strong partitioning was facilitated by favorable electrostatic and π–π interactions but was adversely affected by increased salt. We further identified that dye and salt interactions can be treated as independent control parameters to modulate the properties and electrospinnability of...

We demonstrate antifouling ultrafiltration membranes with retained selectivity and pure water flux through the controlled deposition of zwitterionic polymers and poly(ethylene glycol) (PEG). Molecules for polymerization were immobilized on the membrane’s surface yet prevented from attaching to the membrane’s pores due to a backflow of nitrogen (N2) gas achieved using an in-house constructed apparatus that we named the polymer prevention apparatus, or “PolyPrev”. First, the operating parameters of the PolyPrev were optimized by investigating the polymerization of dopamine, which was selected due to its versatility in enabling further chemical reactions, published metrics for comparison, and its oxidative self-polymerization. Membrane characterization revealed that the polydopamine-modified membranes exhibited enhanced hydrophilicity; moreover, their size selectivity and pure water flux were statistically the same as those of the unmodified membranes. Because it is well documented that polydopamine coatings do not provide a long-lasting antifouling activity, poly(2-methacryloyloxyethyl phosphorylcholine) (polyMPC, Mn = 30 kDa) and succinimidyl-carboxymethyl-ester-terminated PEG (Mn = 40 kDa) were codeposited while dopamine was polymerizing to generate antifouling membranes. Statistically, the molecular-weight cutoff of the polyMPC- and PEG-functionalized membranes synthesized in the PolyPrev was equivalent to that of the unmodified membranes, and the pure water flux of the PEG membranes was equivalent to that of the unmodified membranes. Notably, membranes prepared in the PolyPrev with polyMPC and PEG decreased bovine serum albumin fouling and Escherichia coli attachment. This study demonstrates that by restricting antifouling chemistries from attaching within the pores of membranes, we can generate high-performance, antifouling membranes appropriate for a wide range of water treatment applications without compromising intrinsic transport properties.

By combining antifouling shark-skin patterns with antibacterial titanium dioxide (TiO2) nanoparticles (NPs), we present a simple route toward producing durable multifunctional surfaces that decrease microbial attachment and inactivate attached microorganisms. Norland Optical Adhesive, a UV-crosslinkable adhesive material, was loaded with 0, 10, or 50 wt % TiO2 NPs from which shark-skin microstructures were imprinted using solvent-assisted soft nanoimprint lithography on a poly(ethylene terephthalate) (PET) substrate. To obtain coatings with an exceptional durability and an even higher concentration of TiO2 NPs, a solution containing 90 wt % TiO2 NPs and 10 wt % tetraethyl orthosilicate was prepared. These ceramic shark-skin-patterned surfaces were fabricated on a PET substrate and were quickly cured, requiring only 10 s of near infrared (NIR) irradiation. The water contact angle and the mechanical, antibacterial, and antifouling characteristics of the shark-skin-patterned surfaces were investigated as a function of TiO2 composition. Introducing TiO2 NPs increased the contact angle hysteresis from 30 to 100° on shark-skin surfaces. The hardness and modulus of the films were dramatically increased from 0.28 and 4.8 to 0.49 and 16 GPa, respectively, by creating ceramic shark-skin surfaces with 90 wt % TiO2 NPs. The photocatalytic shark-skin-patterned surfaces reduced the attachment of Escherichia coli by ~70% compared with smooth films with the same chemical composition. By incorporating as low as 10 wt % TiO2 NPs into the chemical matrix, over 95% E. coli and up to 80% Staphylococcus aureus were inactivated within 1 h UV light exposure because of the photocatalytic properties of TiO2. The photocatalytic shark-skin-patterned surfaces presented here were fabricated using a solution-processable and roll-to-roll compatible technique, enabling the production of large-area high-performance coatings that repel and inactivate bacteria.

Despite lacking visual, auditory, and olfactory perception, bacteria sense and attach to surfaces. Many factors, including the chemistry, topography, and mechanical properties of a surface, are known to alter bacterial attachment, and in this study, using a library of nine protein-resistant poly(ethylene glycol) (PEG) hydrogels immobilized on glass slides, we demonstrate that the thickness or amount of polymer concentration also matters. Hydrated atomic force microscopy and rheological measurements corroborated that thin (15 μm), medium (40 μm), and thick (150 μm) PEG hydrogels possessed Young's moduli in three distinct regimes, soft (20 kPa), intermediate (300 kPa), and stiff (1000 kPa). The attachment of two diverse bacteria, flagellated Gram-negative Escherichia coli and nonmotile Gram-positive Staphylococcus aureus was assessed after a 24 h incubation on the nine PEG hydrogels. On the thickest PEG hydrogels (150 μm), E. coli and S. aureus attachment increased with increasing hydrogel stiffness. However, when the hydrogel's thickness was reduced to 15 μm, a substantially greater adhesion of E. coli and S. aureus was observed. Twelve times fewer S. aureus and eight times fewer E. coli adhered to thin-soft hydrogels than to thick-soft hydrogels. Although a full mechanism to explain this behavior is beyond the scope of this article, we suggest that because the Young's moduli of thin-soft and thick-soft hydrogels were statistically equivalent, potentially, the very stiff underlying glass slide was causing the thin-soft hydrogels to feel stiffer to the bacteria. These findings suggest a key takeaway design rule; to optimize fouling-resistance, hydrogel coatings should be thick and soft.

In this study, we have improved membrane performance by enhancing ultrafiltration membranes with electrospun nanofibers. The high-porosity nanofiber layer provides a tailorable platform that does not affect the base membrane structure. To decouple the effects that nanofiber chemistry and morphology have on membrane performance, two polymers commonly used in the membrane industry, cellulose and polysulfone, were electrospun into a layer that was 50 μm thick and consisted of randomly accumulated 1-μm-diameter fibers. Fouling resistance was improved and selectivity was retained by ultrafiltration membranes enhanced with a layer of either cellulose or polysulfone nanofibers. Potentially because of their better mechanical integrity, the polysulfone nanofiber-membranes demonstrated a higher pure-water permeance across a greater range of transmembrane pressures than the cellulose nanofiber-membranes and control membranes. This work demonstrates that nanofiber-enhanced membranes hold potential as versatile materials platforms for improving the performance of ultrafiltration membranes.

In this study, we exploit the excellent fouling resistance of polymer zwitterions and present electrospun nanofiber mats surface functionalized with poly(2-methacryloyloxyethyl phosphorylcholine) (polyMPC). This zwitterionic polymer coating maximizes the accessibility of the zwitterion to effectively limit biofouling on nanofiber membranes. Two facile, scalable methods yielded a coating on cellulose nanofibers: (i) a two-step sequential deposition featuring dopamine polymerization followed by the physioadsorption of polyMPC, and (ii) a one-step codeposition of polydopamine (PDA) with polyMPC. While the sequential and codeposited nanofiber mat assemblies have an equivalent average fiber diameter, hydrophilic contact angle, surface chemistry, and stability, the topography of nanofibers prepared by codeposition were smoother. Protein and microbial antifouling performance of the zwitterion modified nanofiber mats along with two controls, cellulose (unmodified) and PDA coated nanofiber mats were evaluated by dynamic protein fouling and prolonged bacterial exposure. Following 21 days of exposure to bovine serum albumin, the sequential nanofiber mats significantly resisted protein fouling, as indicated by their 95% flux recovery ratio in a water flux experiment, a 300% improvement over the cellulose nanofiber mats. When challenged with two model microbes Escherichia coli and Staphylococcus aureus for 24 h, both zwitterion modifications demonstrated superior fouling resistance by statistically reducing microbial attachment over the two controls. This study demonstrates that, by decorating the surfaces of chemically and mechanically robust cellulose nanofiber mats with polyMPC, we can generate high performance, free-standing nanofiber mats that hold potential in applications where antifouling materials are imperative, such as tissue engineering scaffolds and water purification technologies.

In this study, we exploit the high silver ion exchange capability of Linde Type A (LTA) zeolites and present, for the first time, electrospun nanofiber mats decorated with in-house synthesized silver (Ag(+)) ion exchanged zeolites that function as molecular delivery vehicles. LTA-Large zeolites with a particle size of 6.0 μm were grown on the surface of the cellulose nanofiber mats, whereas LTA-Small zeolites (0.2 μm) and three-dimensionally ordered mesoporous-imprinted (LTA-Meso) zeolites (0.5 μm) were attached to the surface of the cellulose nanofiber mats postsynthesis. After the three zeolite/nanofiber mat assemblies were ion-exchanged with Ag(+) ions, their ion release profiles and ability to inactivate Escherichia coli (E. coli) K12 were evaluated as a function of time. LTA-Large zeolites immobilized on the nanofiber mats displayed more than an 11 times greater E. coli K12 inactivation than the Ag-LTA-Large zeolites that were not immobilized on the nanofiber mats. This study demonstrates that by decorating nanometer to micrometer scale Ag(+) ion-exchanged zeolites on the surface of high porosity, hydrophilic cellulose nanofiber mats, we can achieve a tunable release of Ag(+) ions that inactivate bacteria faster and are more practical to use in applications over powder zeolites.

Clinically, biofilm-associated infections commonly form on intravascular catheters and other hydrogel surfaces. The overuse of antibiotics to treat these infections has led to the spread of antibiotic resistance and underscores the importance of developing alternative strategies that delay the onset of biofilm formation. Previously, it has been reported that during surface contact, bacteria can detect surfaces through subtle changes in the function of their motors. However, how the stiffness of a polymer hydrogel influences the initial attachment of bacteria is unknown. Systematically, we investigated poly(ethylene glycol) dimethacrylate (PEGDMA) and agar hydrogels that were twenty times thicker than the cumulative size of bacterial cell appendages, as a function of Young’s moduli. Soft (44.05 – 308.5 kPa), intermediate (1495 – 2877 kPa), and stiff (5152 – 6489 kPa) hydrogels were synthesized. Escherichia coli and Staphylococcus aureus attachment onto the hydrogels was analyzed using confocal microscopy after 2 and 24 hr incubation periods. Independent of hydrogel chemistry and incubation time, E. coli and S. aureus attachment correlated positively to increasing hydrogel stiffness. For example, after a 24 hr incubation period, there were 52% and 82% less E. coli adhered to soft PEGDMA hydrogels, than to the intermediate and stiff PEGDMA hydrogels, respectively. A 62% and 79% reduction in the area coverage by the Gram-positive microbe S. aureus occurred after 24 hr incubation on the soft versus intermediate and stiff PEGDMA hydrogels. We suggest that hydrogel stiffness is an easily tunable variable that, potentially, could be used synergistically with traditional antimicrobial strategies to reduce early bacterial adhesion, and therefore the occurrence of biofilm-associated infections.

Biopolymer hydrogels are important materials for wound healing and cell culture applications. While current synthetic polymer hydrogels have excellent biocompatibility and are nontoxic, they typically function as a passive matrix that does not supply any additional bioactivity. Chitosan (CS) and pectin (Pec) are natural polymers with active properties that are desirable for wound healing. Unfortunately, the synthesis of CS/Pec materials have previously been limited by harsh acidic synthesis conditions, which further restricted their use in biomedical applications. In this study, a zero-acid hydrogel has been synthesized from a mixture of chitosan and pectin at biologically compatible conditions. For the first time, we demonstrated that salt could be used to suppress long-range electrostatic interactions to generate a thermoreversible biopolymer hydrogel that has temperature-sensitive gelation. Both the hydrogel and the solution phases are highly elastic, with a power law index of close to -1. When dried hydrogels were placed into phosphate buffered saline solution, they rapidly rehydrated and swelled to incorporate 2.7× their weight. As a proof of concept, we removed the salt from our CS/Pec hydrogels, thus, creating thick and easy to cast polyelectrolyte complex hydrogels, which proved to be compatible with human marrow-derived stem cells. We suggest that our development of an acid-free CS/Pec hydrogel system that has excellent exudate uptake, holds potential for wound healing bandages.

Biofilm-associated infections are one of the leading causes of death in the United States. Although infections may be treated with antibiotics, the overuse of antibiotics has led to the spread of antibiotic resistance. Many natural antimicrobial compounds derived from edible plants are safe for human use and target bacteria nonspecifically. Therefore, they may impair biofilm formation with less evolutionary pressure on pathogens. Here, we explore the use of two natural antimicrobial compounds, cinnamaldehyde (CA, from cinnamon) and carvacrol (CARV, from oregano), for biofilm prevention. We have fabricated and characterized films that incorporate CA and CARV into the biodegradable, FDA-approved polymer poly(lactic-co-glycolic acid), PLGA. The addition of CA and CARV to PLGA films not only adds antimicrobial activity but also changes the surface properties of the films, making them more hydrophilic and therefore more resistant to bacterial attachment. An addition of 0.1% CA to a PLGA film significantly impairs biofilm development by Staphylococcus aureus, and 0.1% CARV in PLGA significantly decreases biofilm formation by both Escherichia coli and S. aureus. Pseudomonas aeruginosa, which is less susceptible to CA and CARV, was not affected by the addition of 0.1% CA or CARV to the PLGA coatings; however, P. aeruginosa biofilm was significantly reduced by 1.0% CA. These results indicate that both CA and CARV could potentially be used in low concentrations as natural additives in polymer coatings for indwelling devices to delay colonization by bacteria.

Polymer coatings featuring nonleaching antibacterial agents are needed to significantly reduce bacterial colonization and subsequent biofilm formation. Previously, single-walled carbon nanotubes (SWNTs) have been reported to be strong antimicrobial agents that kill microbes on contact. However, the antibacterial activity of freestanding polymer mats with a low weight percent of incorporated SWNTs has not been demonstrated. In this study, four different weight percents of well characterized, small diameter (0.8 nm) SWNTs were incorporated into electrospun polysulfone (PSf) mats. Electrospun PSf-SWNT mats were observed to be flexible and composed of continuous, cylindrical, and randomly oriented fibers. SEM micrographs revealed that SWNT ends were distributed along the longitudinal fiber axis. Loss of bacteria (Escherichia coli) viability was observed to directly correlate to increased SWNT incorporation within the mat, ranging from 18% for 0.1 wt % SWNTs to 76% for 1.0 wt % SWNTs. Time-dependent bacterial cytotoxicity studies indicated that the antimicrobial action of the PSf-SWNT mats occurs after a short contact time of 15 min or less. This study demonstrates the potential applicability of electrospun PSf-SWNT mats as antibacterial coatings.

In the present study, we have electrospun various grades of chitosan and cross-linked them using a novel method involving glutaraldehyde (GA) vapor, utilizing a Schiff base imine functionality. Chemical, structural, and mechanical analyses have been conducted by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and Kawabata microtensile testing, respectively. Additionally, the solubilities of the as-spun and cross-linked chitosan mats have been evaluated;solubility was greatly improved after cross-linking. SEM images displayed evidence that unfiltered low, medium, and high molecular weight chitosans, as well as practical-grade chitosan, can be electrospun into nanofibrous mats. The as-spun medium molecular weight chitosan nanofibers have a Young's modulus of 154.9 +/- 40.0 MPa and display a pseudo-yield point that arose due to the transition from the pulling of a fibrous mat with high cohesive strength to the sliding and elongation of fibers. As-spun mats were highly soluble in acidic and aqueous solutions. After cross-linking, the medium molecular weight fibers increased in diameter by an average of 161 nm, have a decreased Young's modulus of 150.8 +/- 43.6 MPa, and were insoluble in basic, acidic, and aqueous solutions. Though the extent to which GA penetrates into the chitosan fibers is currently unknown, it is evident that the cross-linking resulted in increased brittleness, a color change, and the restriction of fiber sliding that resulted in the loss of a pseudo-yield point.

Chitin is a nitrogen-rich polysaccharide that is abundant in crustaceans, mollusks, insects, and fungi and is the second most abundant organic material found in nature next to cellulose. Chitosan, the N-deacetylated derivative of chitin, is environmentally friendly, nontoxic, biodegradable, and antibacterial. Fibrous mats are typically used in industries for filter media, catalysis, and sensors. Decreasing fiber diameters within these mats causes many beneficial effects such as increased specific surface area to volume ratios. When the intrinsically beneficial effects of chitosan are combined with the enhanced properties of nanofibrous mats, applications arise in a wide range of fields, including medical, packaging, agricultural, and automotive. This is particularly important as innovative technologies that focus around bio-based materials are currently of high urgency, as they can decrease dependencies on fossil fuels. We have demonstrated that Schiff base cross-linked chitosan fibrous mats can be produced utilizing a one-step electrospinning process that is 25 times faster and, therefore, more economical than a previously reported two-step vapor-cross-linking method. These fibrous mats are insoluble in acidic, basic, and aqueous solutions for 72 h. Additionally, this improved production method results in a decreased average fiber diameter, which measures 128 +/- 40 nm. Chemical and structural analyses were conducted utilizing Fourier transform infrared spectroscopy, solubility studies, and scanning electron microscopy.