Search

Plasma foci of compact sizes and operating with low energies (from tens of joules to few hundred joules) have found application in recent years and have attracted plasma-physics scientists and engineers for research in this direction. We are presenting a low energy and miniature plasma focus which operates from a capacitor bank of 8.4 μF capacity, charged at 4.2–4.3 kV and delivering approximately 52 kA peak current at approximately 60 nH calculated circuit inductance. The total circuit inductance includes the plasma focus inductance. The reported plasma focus operates at the lowest voltage among all reported plasma foci so far. Moreover the cost of capacitor bank used for plasma focus is nearly 20 U.S. dollars making it very cheap. At low voltage operation of plasma focus, the initial breakdown mechanism becomes important for operation of plasma focus. The quartz glass tube is used as insulator and breakdown initiation is done on its surface. The total energy of the plasma focus is approximately 75 J. The plasma focus system is made compact and the switching of capacitor bank energy is done by manual operating switch. The focus is operated with hydrogen and deuterium filled at 1–2 mbar. [ABSTRACT FROM AUTHOR]

A slow-wave delay line type air-core (nonmagnetic Nylon former) current transformer fabricated using silver epoxy for the measurement of currents of long pulse durations and few nanoseconds rise times is reported in this article. The advantage of using silver epoxy is that it fills all the voids between coil and shield and enhances the proximity of the coil to the shield, leading to a high value of distributed capacitance. Thus the transit time of the coil increases and it can measure fast current pulses of longer durations. Increasing the inductance of the coil can compensate for the resulting reduction in the sensitivity of the coil for matched termination. An easy experimental technique to find the value of the matched terminating resistor is also reported in this article. We have also done simulations of the slow wave current transformer using PSPICE. [ABSTRACT FROM AUTHOR]

The dielectric properties of MnFe2O4 and γ-Fe2O3 magnetic nanoparticles embedded in insulating matrices were investigated. The samples showed frequency dependent dielectric anomalies coincident with the magnetic blocking temperature and significant magnetocapacitance above this blocking temperature, as large as 0.4% at H=10 kOe. For both samples the magnetic field induced change in dielectric constant at high temperatures was proportional to the square of the sample magnetization. These measurements suggest that the dielectric properties of magnetic nanoparticles are closely related to the disposition of magnetic moments in the system. This magnetodielectric coupling is believed to arise from extrinsic effects, which are discussed in light of recent work relating magnetoresistive and magnetocapacitive behaviors. [ABSTRACT FROM AUTHOR]

The helical pulsed forming line (PFL) can generate longer duration rectangular pulse in a smaller length. A compact PFL using helical water line is designed and experimentally investigated. The impedance of the helical PFL is 22 ࡎ. The compactness is achieved in terms of reduction in length of the PFL by a factor of 5.5 using helical water PFL as compared to coaxial water PFL of same length. The helical PFL was pulsed charged to 200 kV using a high voltage pulse transformer in 4.5 μs and discharged into the matched 22 ࡎ resistive load through a self-breakdown pressurized spark gap switch. The rectangular voltage pulse of 100 kV, 260 ns (FWHM) is measured across the load. The effect of reduction in water temperature on the pulse width is also studied experimentally. The increase in pulse width up to 7% more is observed by reducing the temperature of the deionized water to 5 °C. It will further reduce the length of the PFL and make the system small for compact pulsed power drivers. [ABSTRACT FROM AUTHOR]

The experimental results of an air-core pulse transformer are presented, which is very compact (<10 Kg in weight) and is primed by a capacitor bank that is fabricated in such a way that the capacitor bank with its switch takes the shape of single-turn rectangular shaped primary of the transformer. A high voltage capacitor assembly (pulse-forming-line capacitor, PFL) of 5.1 nF is connected with the secondary of transformer. The transformer output voltage is 160 kV in its second peak appearing in less than 2 μS from the beginning of the capacitor discharge. The primary capacitor bank can be charged up to a maximum of 18 kV, with the voltage delivery of 360 kV in similar capacitive loads.