Search

Background: A green sample preparation method named deep eutectic solvent-based single drop microextraction (DES-SDME) was developed and optimized for determining trace metribuzin, dichlorvos, and fenthion., Methods: Two hundred seventy experimental runs were performed, and the optimal values of the five influential factors in the DES-SDME method were determined. The design of the study was based on one factor at a time and the peak area of high-performance liquid chromatography was used as a benchmark for comparing analysis results., Results: After optimizing the effective factors, the linearity range, detection limit and quantification limit of the method were determined by drawing calibration curves for the studied analytes., Conclusion: The results indicated the success of the developed method in obtaining acceptable figures of merit as a green preparation method with accuracy and precision., (Copyright© 2023 Pourhossein et al. Published by Tehran University of Medical Sciences.)

Background: Measurement of pesticides in biological matrices is become a serious challenge for researches because of their very low concentration in different matrices. The aim of this study was to develop a new sample preparation method with high accuracy and validity, simplicity and short retention time for determination of malathion., Methods: Dispersive liquid-liquid micro-extraction (DLLME) technique coupled with high-performance liquid chromatography equipped with ultraviolet detector (HPLC-UV) developed for trace extraction and determination of malathion pesticide in human urine samples. This study was done in 2017 at Tehran University of Medical Sciences, Tehran, Iran. One variable at a time (OVAT) method was used to optimize parameters affecting the malathion extraction. Different parameters such as extraction solvent, disperser solvent, and volume of the extraction solvent, volume of the disperser solvent, centrifugation time and speed, salt addition, and sample pH were studied and optimized., Results: Under the optimized conditions, the limit of detection and enrichment factor of the method were 0.5 μg L -1 and 200, respectively. The calibration curve was linear in the concentration range of 2-250 μg L -1 . The relative standard deviation for six replicate experiments at 200 μg L -1 concentration was less than 3%. The relative recoveries of spiked urine samples were 96.3%, 101.7% and 97.3% at three different concentration levels of 50, 200 and 1000 μg L -1 , respectively., Conclusion: DLLME procedure was successfully developed for the extraction of malathion from human urine samples. Compared to other extraction techniques, the proposed procedure had some advantages such as shorter extraction time, better reproducibility, and higher enrichment factor., Competing Interests: Conflict of interests The authors declare that there is no conflict of interest., (Copyright© Iranian Public Health Association & Tehran University of Medical Sciences.)

Background: 4-chloro-2-methylphenoxy acetic acid (MCPA) is one of the most important pesticides which is extensively used to control weeds in arable farmland. Exposure to this compound occurs in general population and persons who occupationally handle it. The aim of this present work was the preparation of MCPA imprinting polymer and its application as a selective sample preparation technique for trace determination of MCPA in biological and environmental samples., Methods: In this study, MCPA imprinting polymer was obtained by precipitation polymerization using methacrylic acid (the functional monomer), ethylene glycol dimethacrylate (the cross-linker), 2, 2'-azobisisobutyronitrile (the initiator) and MCPA (the template molecule) in acetonitrile solution. The MIP-NPs were characterized by thermogravimetric analysis and scanning electron microscopy. The optimization process was carried out applying batch method. After optimization of the parameters, affecting the adsorption and desorption of analyte, urine and different water samples were used to determine MCPA., Results: Imprinted MCPA molecules were removed from the polymeric structure using acetic acid in methanol (20:80 v/v %) as the eluting solvent. Both sorption and desorption process occur within 10 min. The maximum sorbent capacity of the molecular imprinted polymer is 87.4 mg g-1. The relative standard deviation and limit of detection for water samples by introduced selective solid phase extraction were 4.8% and 0.9 μg L-1, and these data for urine samples were 4.5% and 1.60 μg L-1, respectively., Conclusion: The developed method was successfully applied to determine MCPA in urine and different water samples.