Search

Background: It is difficult to repair cartilage damage when cartilage undergoes trauma or degeneration. Cartilage tissue engineering is an ideal treatment method to repair cartilage defects, but at present, there are still some uncertainties to be researched in cartilage tissue engineering including the mechanical properties of the repaired region. Methods: In this study, using an agarose gel as artificial cartilage implanted into the cartilage defect and gluing the agarose gel to cartilage by using the medical bio-adhesive, the full-thickness and half-thickness defects models of articular cartilage in vitro repaired by tissue engineering were constructed. Strain behaviors of the repaired region were analyzed by the digital correlation technology under 5,10, 15, and 20% compressive load. Results: The axial normal strain (Ex) perpendicular to the surface of the cartilage and lateral normal strain (Ey) as well as shear strain (Exy) appeared obviously heterogeneous in the repaired region. In the full-defect model, Ex showed depth- dependent strain profiles where maximum Ex occurs at the low middle zone while in the half-defect mode, Ex showed heterogeneous strain profiles where maximum Ex occurs at the near deep zone. Ey and Exy at the interface site of both models present significantly differed from the host cartilage site. Ey and Exy exhibited region-specific change at the host, interface, and artificial cartilage sites in the superficial, middle, and deep zones due to the artificial cartilage implantation. Conclusion: Both defect models of cartilage exhibited a heterogeneous strain field due to the engineered cartilage tissue implant. The abnormal strain field can cause the cells within the repaired area to enter complex mechanical states which will affect the restoration of cartilage defects. [ABSTRACT FROM AUTHOR]

Background: Facet joints play a significant role in providing stability to the spine and they have been associated with low back pain symptoms and other spinal disorders. The influence of a follower load on biomechanics of facet joints is unknown. A comprehensive research on the biomechanical role of facets may provide insight into facet joint instability and degeneration.Method: A nonlinear finite element (FE) model of lumbar spine (L1-S1) was developed and validated to study the biomechanical response of facets, with different values of follower preload (0 N,500 N,800 N,1200 N), under loadings in the three anatomic planes. In this model, special attention was paid to the modeling of facet joints, including cartilage layer. The asymmetry in the biomechanical response of facets was also discussed. A rate of change (ROC) and an average asymmetry factor (AAF) were introduced to explore and evaluate the preload effect on these facet contact parameters and on the asymmetry under different loading conditions.Results: The biomechanical response of facets changed according to the loading condition. The preload amplified the facet force, contact area and contact pressure in flexion-extension; the same effect was observed on the ipsilateral facet while an opposite effect could be seen on the contralateral facet during lateral bending. For torsion loading, the preload increased contact area, decreased the mean contact pressure, but had almost no effect on facet force. However, all the effects of follower load on facet response became weaker with the increase of preload. The greatest asymmetry of facet response could be found on the ipsilateral side during lateral bending, followed by flexion, bending (contralateral side), extension and torsion. This asymmetry could be amplified by preload in the bending (ipsilateral), torsion loading group, while being reduced in the flexion group.Conclusions: An analysis combining patterns of contact pressure distribution, facet load, contact area and contact pressure can provide more insight into the biomechanical role of facets under various moment loadings and follower loads. The effect of asymmetry on facet joint response should be fully considered in biomechanical studies of lumbar spine, especially in post structures subjected to physiological loadings. [ABSTRACT FROM AUTHOR]

Background: Facet joints play a significant role in providing stability to the spine and they have been associated with low back pain symptoms and other spinal disorders. The influence of a follower load on biomechanics of facet joints is unknown. A comprehensive research on the biomechanical role of facets may provide insight into facet joint instability and degeneration., Method: A nonlinear finite element (FE) model of lumbar spine (L1-S1) was developed and validated to study the biomechanical response of facets, with different values of follower preload (0 N,500 N,800 N,1200 N), under loadings in the three anatomic planes. In this model, special attention was paid to the modeling of facet joints, including cartilage layer. The asymmetry in the biomechanical response of facets was also discussed. A rate of change (ROC) and an average asymmetry factor (AAF) were introduced to explore and evaluate the preload effect on these facet contact parameters and on the asymmetry under different loading conditions., Results: The biomechanical response of facets changed according to the loading condition. The preload amplified the facet force, contact area and contact pressure in flexion-extension; the same effect was observed on the ipsilateral facet while an opposite effect could be seen on the contralateral facet during lateral bending. For torsion loading, the preload increased contact area, decreased the mean contact pressure, but had almost no effect on facet force. However, all the effects of follower load on facet response became weaker with the increase of preload. The greatest asymmetry of facet response could be found on the ipsilateral side during lateral bending, followed by flexion, bending (contralateral side), extension and torsion. This asymmetry could be amplified by preload in the bending (ipsilateral), torsion loading group, while being reduced in the flexion group., Conclusions: An analysis combining patterns of contact pressure distribution, facet load, contact area and contact pressure can provide more insight into the biomechanical role of facets under various moment loadings and follower loads. The effect of asymmetry on facet joint response should be fully considered in biomechanical studies of lumbar spine, especially in post structures subjected to physiological loadings.