Search

The development of diplexers for ECRH has been pursued at a number of institutes because of their attractive variety of applications: Power combination, non-mechanical, electrically controlled switching (of combined beams) between launchers with tens of kHz, and discrimination of low-power ECE signals from high-power ECRH is feasible. In a first part, this paper reports on plasma experiments with a ring resonator (Mk IIa) at ASDEX Upgrade. Commissioning experiments on fast switching between two launchers for synchronous stabilization of neoclassical tearing modes, as well as in-line ECE measurements have been performed, and experimental issues and first results are discussed. A clear influence of the switching phase on the amplitude of the 3/2 NTM mode was measured, complete stabilization could, however, not be demonstrated yet mainly due to imperfect resonator control. Concepts for improved tracking of the diplexers to the gyrotron frequency are presented. In a second part, the design of diplexers with ring resonators matched to HE11 fields is briefly discussed; these devices can be connected to corrugated waveguides without any mode converters. A compact version (MQ IV) is under investigation, which is compatible with the ITER ECRH system (170 GHz, 63.5 mm waveguide, vacuum tight casing), with the final goal of high-power tests at the 170 GHz gyrotron facility at JAEA in Naka, Japan. First low-power test results are presented.

Sensitive millimeter wave diagnostics need often to be protected against unwanted radiation like, for example, stray radiation from high power Electron Cyclotron Heating applied in nuclear fusion plasmas. A notch filter based on a waveguide Bragg reflector (photonic band-gap) may provide several stop bands of defined width within up to two standard waveguide frequency bands. A Bragg reflector that reflects an incident fundamental TE11 into a TM1n mode close to cutoff is combined with two waveguide tapers to fundamental waveguide diameter. Here the fundamental TE11 mode is the only propagating mode at both ends of the reflector. The incident TE11 mode couples through the taper and is converted to the high order TM1n mode by the Bragg structure at the specific Bragg resonances. The TM1n mode is trapped in the oversized waveguide section by the tapers. Once reflected at the input taper it will be converted back into the TE11 mode which then can pass through the taper. Therefore at higher order Bragg resonances, the filter acts as a reflector for the incoming TE11 mode. Outside of the Bragg resonances the TE11 mode can propagate through the oversized waveguide structure with only very small Ohmic attenuation compared to propagating in a fundamental waveguide. Coupling to other modes is negligible in the non-resonant case due to the small corrugation amplitude (typically 0.05·λ0, where λ0 is the free space wavelength). A Bragg reflector for 105 and 140 GHz was optimized by mode matching (scattering matrix) simulations and manufactured by SWISSto12 SA, where the required mechanical accuracy of ± 5 μm could be achieved by stacking stainless steel rings, manufactured by micro-machining, in a high precision guiding pipe. The two smooth-wall tapers were fabricated by electroforming. Several measurements were performed using vector network analyzers from Agilent (E8362B), ABmm (MVNA 8-350) and Rohde&Schwarz (ZVA24) together with frequency multipliers. The stop bands around 105 GHz (- 55dB) and 140 GHz (-60dB) correspond to the TE11-TM12 and TE11-TM13 Bragg resonances. Experiments are in good agreement with theory.

Characteristics of ring resonator diplexers for high-power ECRH are briefly reviewed. Commissioning experiments performed on ASDEX Upgrade with the diplexer Mk IIa are presented, which demonstrate slow and fast switching of the power between two launchers, and thus the capability for efficient suppression of neoclassical tearing modes and simultaneous central heating of the plasma. The development of the compact diplexer Mk IIIb is discussed, and test results are presented. Finally, an evacuated design for 170 GHz is shown.

High-power resonant diplexers for millimetre waves have various promising applications in ECRH systems. The round-trip resonator length of a diplexer needs to be accurately tuned to match its prescribed functionality. For this purpose one of the mirrors in the FADIS MkIIa diplexer has been mounted on a motion system, in order to control the mirror to its desired location despite the presence of substantial disturbances. The mechanical properties and control strategy for the mirror motion system have been designed such as to meet the overall system requirements. The performance of the motion system has been experimentally validated in various high power mm-wave tests.