Search

The fabrication of most current thermal insulation materials from polymeric foams has created an unfavorable impact on the environment. With the aim of reducing the use of foam plastic, this paper focuses on honeycomb paperboard, an alternative thermal insulation material which is recyclable and cost-effective, and evaluates its heat transfer performance under different conditions. The experimental results show the effective thermal conductivity of honeycomb paperboard increases as the honeycomb height or the side length increases. This paper also establishes a novel theoretical model based on a newly developed convective heat transfer correlation to predict the effective thermal conductivity under different conditions. The model's results conform well to the experimental results, and the effect of convective heat transfer is investigated quantitatively using this model. As the vertical adiabatic boundary surfaces are replaced by honeycomb walls, the convection heat transfer strictly depends on the thermal boundary condition of the honeycomb walls and highly depends on honeycomb height and side length. • The novel theoretical models involving convective heat transfer are established under different conditions. • The different heat transfer paths are quantitatively investigated based on the proposed models. • Under the condition of hot-above and cold-below, convective heat transfer in honeycomb paperboard increases as the honeycomb height increases, but decreases as the side lengths increases. • Under the condition of cold-above and hot-below, convection heat transfer in honeycomb paperboard increases as the honeycomb height or the side length increases. [ABSTRACT FROM AUTHOR]

The environment inside a spacecraft, or a space habitat, can greatly differ from those on earth, affecting the burning behavior of solid fuels. Because in a gravity field there is a flame-induced buoyancy, it is very difficult to reproduce on Earth the environmental conditions of a spacecraft, or a habitat in the Moon or Mars, thus making fire testing and burning predictions harder. A potential alternative approach to overcome this problem is to reduce buoyancy effects by using reduced ambient pressure in normal gravity. The objective of this work is to explore the possibility of simulating the effect of gravity, and in turn buoyancy, through changes in ambient pressure, on upward/concurrent flame spread over a thin combustible solid. Comparisons with available data at different gravity levels are used to determine the extent to which low-pressure can be used to replicate flame spread characteristics at different gravities. Experiments of the upward/concurrent flame spread over thin Kimwipe paper sheets were conducted in normal gravity inside a pressure chamber with ambient pressures ranging between 100 and 30 kPa and a forced flow velocity of 10 cm/s. Results show that reductions of pressure slow down the flame spread over the paper surface, and also reduces flame intensity. Comparison with published partial gravity data shows that as the pressure is reduced, the normal gravity flame spread rate approaches that observed at different gravity levels. The data presented is correlated in terms of a mixed convection non-dimensional number that describes the convective heat transferred from the flame to the solid, and that also describes the primary mechanism controlling the spread of the flame. The correlation provides information about the similitudes of the flame spread process in variable pressure, flow velocity and gravity environments, providing guidance for potential ground-based testing for fire safety design in spacecraft. [ABSTRACT FROM AUTHOR]

Abstract: In the finite volume approach for incompressible flow and heat transfer, the discretization of the convection term and the treatment of the coupling between velocity and pressure are the two major issues affecting solution stability, accuracy and convergence rate. In this review paper, some recent advances made in the CFD/NHT & Enhanced Heat Transfer Center of Xi''an Jiaotong University, China, are presented and their applications in the study of heat transfer enhancement are also briefly summarized. [Copyright &y& Elsevier]

This research paper focuses on CFD analysis for comparative evaluation of different hybrid nanofluids (NFs): MWCNT-Al 2 O 3 /H 2 O, MWCNT-MgO/H 2 O, Al 2 O 3 -CuO/H 2 O performance as working fluid (WF) inside parabolic trough solar collector (PTSC). The performance of the collector is evaluated using different performance indicators, including Nusselt number (Nu), friction factor (f), and Performance Evaluation Criterion (PEC) for different Reynolds number (Re) (10000-50000). Among the investigated hybrid nanoparticles (NPs), MWCNT-Al 2 O 3 emerges as the most promising choice for significantly enhancing the system's thermal performance with the highest PEC value of 1.9. This outcome signifies the superior efficiency of MWCNT-Al₂O₃/H₂O hybrid NF in enhancing convective heat transfer, thus underlining the paramount significance of adopting them in thermal systems operating within the specified Re range. [ABSTRACT FROM AUTHOR]

This paper describes an accurate model of the Electrical Power Subsystem (EPS) of the Thermal Analysis Support and Environment Characterization Laboratory (TASEC-Lab), a university experiment developed for using in high-altitude balloon missions to measure and analyze the convection heat transfer. A Li-ion battery and two high efficient DC–DC converters have been characterized through laboratory tests and fitting to the experimental results. The developed mathematical models described in this paper are used to carry out accurate EPS simulations and are validated by comparison with the experimental data. • Design and modeling of the electrical power subsystem of a stratospheric balloon experiment. • New Li-lion battery discharging model that describes the three main parts: initial decay, linear, and exponential decay. • Formulation of a new DC/DC converter efficiency model. • Simulation and model validation of the electrical power subsystem. [ABSTRACT FROM AUTHOR]

Chemical ablation and mechanical erosion of hybrid rocket nozzles can cause loss of nozzle thermal protection material, resulting thrust reduction. In this paper, the chemical ablation and mechanical erosion mechanisms of nozzle thermal protection materials are studied through numerical simulation. For chemical ablation, a coupled thermal-mechanical-chemical model is established, considering three mechanisms: wall regression caused by non-homogeneous chemical reactions at the wall, convective heat transfer and fluid-structure interaction. For mechanical erosion, a Fluent DPM model and an Abaqus DEM model are established, which are investigated from the perspectives of empirical formula and solid mechanics mechanisms respectively, and validated against each other. The comprehensive effect of chemical ablation and mechanical erosion on the morphology of the nozzle is considered. The results show that both chemical ablation and mechanical erosion dominate the wall regression rate at the downstream of the converging section and upstream of the throat while the other location is only dominate by chemical ablation. After 5s of operation, thrust of rocket engine decreases by 5.8%. The Abaqus DEM model presented by this paper breaks the limitations of the empirical formulae due to the introduction of the material constitutive model and the failure criterion. • A coupled thermal-mechanical-chemical model is established. • Mechanical erosion is studied from perspective of empirical formula and the solid mechanics mechanism. • Comprehensive effect of chemical ablation and mechanical erosion on nozzle inner wall morphology is studied. [ABSTRACT FROM AUTHOR]

• Mixed convection for a viscoelastic fluid within a square enclosure containing a rotating cylinder was numerically simulated. • The Phan-Thien-Tanner (PTT) model was used to describe the viscoelastic fluid behavior via the OpenFOAM software. • The numerical divergence at high Weissenberg numbers was addressed using a log-conformation approach. • Elevating the Weissenberg number reduced the frictional torque by 54 % and raised the Nusselt number from −1.33 to 3.32. • As the Weissenberg number increased from 1 to 100, there was a significant decline in the tangential normal stress. This paper for the first time conducted numerical simulations for the mixed convective flow and heat transfer with a viscoelastic fluid within a square enclosure containing a rotating cylinder. The flow regime was considered laminar, two-dimensional, and transient, and the Phan-Thien-Tanner (PTT) model, recognized as one of the most accurate nonlinear models for viscoelastic fluids, was used to describe the viscoelastic fluid behavior, mathematically. Solving nonlinear fluid equations, predicting the complex properties of viscoelastic fluids using the constitutive equation of the PTT model, and considering viscous dissipation were the challenges of this research. Additionally, the paper addressed the numerical divergence at high Weissenberg numbers using a log-conformation approach based on a logarithmic variable change in the polymer stress equation. The effects of the Richardson, Weissenberg, and Brinkman numbers and the ratio of polymeric viscosity to total viscosity on fluid flow and heat transfer were investigated by solving the nonlinear equations via the finite volume method. This was accomplished using the rheoHeatFoam solver within the OpenFOAM software. Local and average heat transfer characteristics around the rotating cylinder were fully studied. The results showed that elevating the Weissenberg number enhances the shear-thinning effect and diminishes the effective viscosity of the fluid by 63 %, resulting in a 54 % reduction in both the shear stress around the cylinder and the frictional torque applied to it, as well as a decrease in the viscous dissipation. Furthermore, increasing the Weissenberg number raised the Nusselt number from -1.33 to 3.32, signifying a complete reversal in the direction of heat transfer. However, the shear-thinning effect became negligible when the Weissenberg number exceeded 100. Moreover, the tangential normal stress significantly increased with an increase in the Weissenberg number up to one. However, as the Weissenberg number increased from 1 to 100, there was a significant decline in the tangential normal stress. Consequently, at very high Weissenberg numbers, the tangential normal stress approached zero, resembling a Newtonian fluid. [ABSTRACT FROM AUTHOR]

A novel air-carrying energy radiant diffuse terminal is proposed, and the response of the terminal is investigated by field experiment and numerical simulation. This paper explores the dynamic operation characteristics of the new system to guide the optimal operation of the system. A transient simulation method of three factors (conduction, convection, and radiation) with dual-circulation (air-carrying energy zone and occupied zone) is put forward for the radiant diffuse terminal with a fresh air system. This transient simulation sets up the porous baffle model coupling radiation model concurrently, revealing the dynamic thermal performance for the system's response accurately, quickly, and comprehensively. This method avoids the limits for the complexity of mini porous (Pore size of 1 mm–3mm) geometric models and the transient uncertainty in multiple combination models. The results show that the average error between the convective-conductive model and the convective-conductive-radiative model is about 8% at five different heights. This system has high response performance, which can quickly heat the room while maintaining the comfort requirements of vertical temperature. The radiated heat transfer between the radiant diffuse terminal and the occupied zone is greater than the convective heat transfer (Radiation accounts for 74%). This system has a short response time, high energy efficiency, uniform airflow, and eliminates draught rating. Moreover, the indoor non-uniform transient thermal and humid environments, the thermal comfort, and air quality for the response of the terminal with fresh air system under four different diffuser placements are compared using computational fluid dynamic simulation. The results indicate that introducing heating strategies featuring higher-positioned fresh air inlet and lower-positioned recirculation return air outlet for this system leads to a temperature efficiency increase by 5%, velocity uniformity by 8%, and age of air reduction by 16–50% in human-breathed zone and the response time by 25%, which shows substantial potential for energy savings. The transient simulation and experiments in the paper are beneficial to optimize design parameters and carry out energy-saving applications of operation energy consumption for the response of this terminal with a fresh air system in the future. [Display omitted] • Dynamic feature of the new terminal system is explored by experiments and simulation. • The validated porous baffle model simplifies geometry modeling for mini perforations. • A new transient simulation method of dual-cycle three factors is proposed. • High performance of thermal and humid environment for the response of the system. [ABSTRACT FROM AUTHOR]

Nanochannels consisting of hot and cold walls with periodic rectangular and triangular nanostructures were simulated by molecular dynamics in this paper, the periodic size dimensionless parameters φ was defined to describe the dimension of nanostructures on the wall. The results show that the addition of nanostructures leads to the variation of mass density distribution of fluid near the wall. A hot wall with nanostructures can promote the appearance of a fluid high-potential area near it. The discrepant attraction for fluid from the wall caused by the different wall conditions leads to different flow characteristics in nanochannels. Fluid velocity growth rate near the hot wall is 10.5% higher than that near the cold wall. Average velocity of the fluid near the hot wall is 5.1% higher than that of fluid near the cold wall. A wall with rectangular nanostructures at φ = 0.28 shows minimum flow resistance among rough hot walls, while a wall with triangular nanostructures at φ = 0.14 has minimum flow resistance among rough cold walls. Heat is transferred from the hot wall to the cold wall through fluid flow. Wall conditions impact the heat transfer situation of fluid in flow boundary by changing the fluid mass density contribution. The addition of nanostructures and decrease of nanostructures size is beneficial for heat transfer while unfavorable for fluid flow, convective heat transfer was influenced by their combination. For a wall with 300 K, the addition of rectangular nanostructures at φ = 0.07 has the best convective heat transfer performance. For a wall with 200 K temperature, increasing triangular nanostructures at φ = 0.14 on the wall can reach the best convective heat transfer capacity. This paper can provide a theoretical foundation for the optimization of nanochannels to achieve best convective heat transfer ability. [ABSTRACT FROM AUTHOR]

The presence of magnetic field results in a reduction in natural convective heat transfer and entropy generation in cavities. The use of nanofluids improves the performance of thermal systems. The present paper discusses the impact of uniform and non-uniform magnetic fields on the second-law performance of nanofluid-filled and porous cavities, introduces artificial intelligence (AI) approaches, and examines the applications of AI in optimizing heat transfer and entropy generated in these systems. The mathematical formulation is presented in terms of the entropy generation for natural convection in cavities. This paper demonstrates the influences of various important non-dimensional parameters on entropy generation in cavities. Besides, advances in the second-law performance of cavities and the role of AI techniques in the field are discussed and future directions are provided. [ABSTRACT FROM AUTHOR]

Stratospheric ballooning flights are becoming more relevant due to these platforms can place payloads to an altitude above almost 99% of the atmosphere, where the environmental conditions are very similar to the space ones. From a thermal point of view, during the ascent phase convection is very relevant and, despite what a priori may be thought, depending on the element considered, convection may not be negligible at the float phase. With this in mind, the Thermal Analysis Support and Environment Characterization Laboratory (TASEC-Lab) was born. It is an experiment based on COTS, which consists in a 3U CubeSat-like experiment, which was launched onboard a stratospheric balloon in León (Spain) on 16th, July 2021. The upper unit of the 3U box contains a heated plate, with the aim of quantifying the relevance of convection during the flight. In this paper, the relevance of convection during the ascent phase is described, the correlation of in-flight temperature measurements with those provided by the thermal mathematical model developed in ESATAN-TMS is performed, using the air mass flow inside the cavity as a fitting parameter with a fitting error lower than 5 °C during the ascent phase. [ABSTRACT FROM AUTHOR]

• An analytical model for thermoelastic crack problems in a strip is developed. • Convective heat transfer on lateral surfaces of the strip is considered. • Analytical solutions for thermoelastic field at crack tips are obtained. • Convective heat transfer impacts the SIFs and energy release rate significantly. • It is helpful in improving the understanding of thermoelastic fracture mechanics. Most existing thermoelastic crack models commonly overlook the convective heat exchange occurring on the lateral surfaces of the structures being studied. Consequently, there is often a concern regarding the accurate estimation of temperature fields and the resulting thermal stresses. To address this concern, this paper presents a two-dimensional (2D) thermoelastic model for a cracked strip that incorporates convective heat transfer between the lateral surfaces and the ambient environment. The crack problem is reduced to a set of singular integral equations with Cauchy kernels which are solved numerically. Analytical solutions for temperature distribution, stress intensity factors (SIFs) and energy release rate at crack tips are obtained. The influence of the ratios of convective heat transfer coefficient to thermal conductivity and thickness to height of the strip on the key fracture parameters is investigated through the numerical results. It has been discovered that classical thermoelastic crack models often exhibit a significant underestimation of the SIFs and energy release rates for cracks located near the hot boundary of the strip. The analytical model proposed in this paper has significant potential to advance our understanding of thermoelastic fracture mechanics. [ABSTRACT FROM AUTHOR]

This paper presents numerical simulation of graphe nanoplatelet (GNP) – sodium dodecylbenzene sulfonate (SDBS) – water nanofluid with volumetric mass fractions of ϕ equal to 0–0.1%. The new microchannel is made of 2 layers and has sinusoidal cavities along with the heat sink. The study was conducted for Re = 50, 300, 700 and 1000 (laminar flow). Based on the results, higher Re leads to more convective heat transfer coefficient. Therefore, the value of temperature gradients decreases and on the other hand the effect of cooling fluid temperature in warm areas near solid wall becomes important. Using a higher value of Re results in the penetration of heat in the fluid layer decreases which in general will reduce the temperature of the outlet section in larger Re values. Also, larger Re value results in larger development length which is also a cause for lack of thermal development and dominance of the temperature of the coolant flow in the heat sink resulting in decreased outlet section temperature for higher Reynolds numbers. For Re = 50 and 300 because of lower fluid velocity, the effect of surface geometry factors such as sinusoidal paths or hollow parts (cavities) has a smaller influence on the pressure loss or friction factor of the flow. [ABSTRACT FROM AUTHOR]

Integrating nanotechnology into phase change materials (PCMs) has emerged as a novel approach to improving PCM thermal properties and performance in various thermal energy storage applications. Nanofluids, nanoparticle suspensions in a base fluid, have been identified as a promising method of increasing the thermal conductivity of PCMs and thus reducing thermal energy charging and discharging duration. This review paper investigates recent advances in incorporating nanotechnology into PCMs, focusing on their applications in the solar energy sector. Thermal conductivity, specific heat, viscosity, density, and convective heat transfer coefficient of nanofluids are discussed, as are the thermal properties of nano-enhanced PCMs (NEPCMs), including thermal conductivity, latent heat, specific heat, viscosity, supercooling, and phase-change temperature. The paper also gives an in-depth look at the uses of nanofluids and NEPCMs in solar collectors, photovoltaic/thermal (PV/T) systems, coolants, and desalination, emphasizing their potential to improve system efficiency. The review also considers the potential environmental and human health concerns connected with using nanofluids and NEPCMs, emphasizing the importance of rigorous evaluation and risk assessment in developing and applying these materials. Overall, the review provides valuable insights into the potential benefits and challenges of incorporating nanotechnology into PCMs and emphasizes the importance of ongoing research and development in this field to further advance the use of thermal energy storage technologies in various applications, including solar energy systems. [Display omitted] • Nanofluids and nanomaterials are considered as innovative heat transfer medium. • Phase change materials (PCMs) for harvesting thermal energy are scrutinized. • Recent developments and properties of nanofluids and nano-enhanced PCM. • Potential applications of nanofluids and nano-enhanced PCM are fully presented. • Environmental impacts and human health risks are comprehensively discussed. [ABSTRACT FROM AUTHOR]

Unsteady oblique stagnation-point flow and heat transfer of fractional Maxwell fluid with convective derivative towards an oscillating tensile plate are discussed in this paper. The fractional operator is introduced to material derivative for the first time to obtain a newly defined constitutive equation of Maxwell fluid. The Fourier's law is modified accordingly. The pressure gradient is innovatively obtained by solving the differential equation, which bases on the momentum equation away from the plate. Furthermore, the numerical solutions are acquired by virtue of the finite difference method combined with L1-algorithm. It turns out to be convergent through constructing numerical example. The influence of related parameters on the velocity and temperature are performed graphically in detail. Results show that the fluid velocity and temperature distributions tend to periodic oscillation near the plate. Both the velocity and the temperature reduce with the augment of fractional derivative parameters, which indicates the velocity and the temperature boundary layer become thinner. The smaller velocity relaxation time parameter leads to enhanced velocity, meaning that the pressure promotes the fluid velocity. It is evident that all the temperature curves have a tendency to increase first and then decrease with the diverse parameters due to the thermal relaxation characteristic. [ABSTRACT FROM AUTHOR]

Combustion of iron powder is a promising option for clean and sustainable generation of heat and power. However, a fundamental understanding of the flame propagation mode is missing, especially under strong convection effects. In part I of this work, we analyzed the modes of flame propagation under weak convection effects and estimated the discreteness parameter as a ratio of the particle burn time to the conduction timescale. We found that both, the selection of temperature at which thermal properties are evaluated, and the selected length scale, are critical for a reliable prediction of the transitional particle spacing indicating the transition from the continuous to the discrete mode. In this paper, we extend our previous work by studying the effect of convection on inter-particle heat and mass transfer using boundary layer resolved numerical simulations. It is shown that for increasing convection, iron flames transition from the continuous to the discrete mode at higher particle distances. Taking into account both diffusion and convection-dominated heat transfer, an extension for the scaling of transitional particle spacing of part I is proposed. Furthermore, since iron flames could experience varying ranges of particle distances at different velocities in a practical flame, a regime diagram is constructed which is based on the Péclet number and the particle spacing with a boundary separating the two modes of flame propagation. The regime diagram offers orientation for simulations of large-scale flames using Euler–Lagrange methods where boundary layers around the particles are not resolved. [ABSTRACT FROM AUTHOR]

To deal with inverse nonlinear heat transfer problems in a two-dimensional heat conduction problem, this paper presents a hybrid approach combining fuzzy logic and the extended Kalman filter (EKF). The proposed algorithm has been applied to the real-time reconstruction of the temperature field, time-varying convective heat transfer coefficient, and time-varying boundary heat flux using temperature data from a set of sensors. The effects of the covariance of the initial estimation error, the time step of data acquisition by the sensors, and the number of installed sensors on the precision and stability of the estimation results has been investigated by numerical experiments. To compare and validate the results, all these parameters were investigated using the EKF method. The results show that the adaptive fuzzy extended Kalman filter (FEKF) method for estimating temperature, convection coefficient, and heat flux at the boundaries is precise and stable. The comparison shows that the performance of the FEKF method in parameter estimation is better than the EKF method, and the highest increase in precision and stability of the results is related to the convective heat transfer coefficient. [ABSTRACT FROM AUTHOR]

• A reservoir-assisted loop thermosyphon with a micro-grooved evaporator (MGTPLT) was fabricated. • Micro-grooved structures allowed faster startup and more stable operation of the MGTPLT. • The convection heat transfer ratio was proposed to evaluate the heat transfer enhancement. • The MGTPLT reduced evaporator temperatures and achieved thermal performance enhancement. The two-phase loop thermosyphon (TPLT) offers significant advantages in high-efficiency and long-distance heat transport for various thermal and energy-related applications without external power consumption. In this paper, the startup and heat transfer characteristics of a reservoir-assisted loop thermosyphon with a micro-grooved evaporator (MGTPLT) were experimentally investigated and compared with a loop thermosyphon having a smooth-tube evaporator (STPLT). R245fa was used as a working fluid at volumetric filling ratios of 50–80 %. The results demonstrated that the additional microgrooves allowed a shorter startup time characterized by a lower maximum temperature with respect to the temperature overshoot. Compared to the STPLT, the MGTPLT exhibited lower evaporator temperatures and better temperature uniformities; the micro-grooved structures could alleviate local intermittent dry-out at moderate and high levels of power input for filling ratios of 50 and 60 %. The addition of micro-grooved structures enhanced the heat transfer performance of the TPLT characterized by lower thermal resistances. The convection heat transfer ratio (CHTR) was proposed to evaluate the enhancement of the convection heat transfer within the evaporator region after using microgrooves. The CHTR showed a decreasing tend with increasing the power input. At moderate filling ratios, the value of the CHRT was greater than 1.1, and an approximately 18 % increase in the convection heat transfer was achieved under the combined condition of 60 % filling ratio and 250 W power input. The fundamental mechanism of heat transfer performance enhancement with the aid of micro-grooved structures was analyzed and elucidated. [ABSTRACT FROM AUTHOR]

• Presents an analytical solution for thermal spreading in a cylindrical body with spatially varying side wall cooling. • A series solution is derived, with coefficients shown to be the solution of a set of linear algebraic equations. • Impact of key non-dimensional parameters on temperature field and thermal resistance is investigated. • Results are shown to be in excellent agreement with past work for special cases. • Results are of relevance for edge cooling of microprocessor chips as well as batteries. Thermal spreading and constriction resistance play an important role in thermal management of a variety of engineering systems, including semiconductor devices. Moreover, thermal contact resistance at interfaces between materials is also governed by spreading and constriction processes. Most of the past literature on theoretical modeling of thermal spreading from a source into a larger body assumes an adiabatic side wall, whereas several recent thermal management problems involve active cooling at the side wall. This work addresses such scenarios by solving the thermal spreading problem in a finite thickness cylinder with spatially varying convective heat transfer on the side wall. An eigenfunction-based series solution for the temperature field is written, the coefficients of which are shown to be governed by a set of coupled algebraic equations. Results are shown to agree well with past work for special cases of the general analysis presented here. Thermal spreading resistance is computed for a number of practical scenarios, including step function, periodic and sinusoidal convective cooling on the side wall. In each case, it is shown that the temperature distribution is consistent with the nature of the spatially varying boundary condition. A key theoretical insight from this work is that under certain conditions, the classical definition of thermal spreading resistance may become negative due to the presence of two heat sinks in the problem. Therefore, analysis based on total resistance may be more appropriate. This work offers a significant generalization of past papers, making it possible to analyze realistic thermal management problems, in which, side wall cooling plays an important role. [ABSTRACT FROM AUTHOR]

As a phase change material, ice slurry has been successfully applied in HVAC&R systems due to its high energy storage density. The heat exchangers are the key equipment realizing energy conversion of ice slurry. In HVAC&R systems, U-tubes are frequently used in shell and tube heat exchanger. However, there are few studies on thermo-fluidic characteristics of ice slurry in U-tubes. Therefore, the thermo-fluidic characteristics of ice slurry in U-tubes are numerically studied in this paper using Euler-Euler approach. The results indicated that as enlarging the inlet ice content and velocity, the ice concentration distribution becomes more uniform along in vertical profile. Due to the secondary flow in bend section, the ice concentration decreases in the inner wall and increases in the outer wall as the inlet velocity increases; At the high Reynolds number, the inlet ice content and ice particle diameter have a more significant fluence on pressure drop (Δ p). The local heat transfer coefficient (h lo) in bend section exhibits a tendency of first increasing and then decreasing, with the maximum value of h lo occurs at θ = 90° of the bend section. Finally, a correlation is suggested between the average resistance coefficient (f ave) and local Nusselt number (Nu lo). • The melting process of ice slurry in U-tubes is investigated. • The factors affecting thermo-fluidic behavior of ice slurry in U-tubes are discussed. • This peak value of h lo is located within the bending section at an angle of θ = 90°. • The correlation of f ave and Nu lo in U-tubes is obtained for ice slurry. [ABSTRACT FROM AUTHOR]

In this paper, by means of the finite element method, the MHD free convection flow of non-Newtonian nanoliquid inside a halved annulus enclosure considering a constant heat flux is being applied to the straight walls has been analyzed. The enclosure is loaded with water and nanoparticles of alumina (Al 2 O 3) the combination of these tows produces a liquid that shows shear-thinning behavior. The governing parameters of this study are the Rayleigh number (103 ≤ Ra ≤ 106), inclination angle (0 ≤ α ≤ 90), power-law index (0.6 ≤ n ≤ 1) and Hartmann number (0 ≤ Ha ≤ 100). The outcomes indicate that the inclination angle of the cavity and the Hartmann number can be considered as effective control parameters at different Rayleigh numbers. While the magnetic field is applied the velocity field retarded and hence convection heat transfer and the Nusselt number diminished, and the increment of power-law index prompts the heat transfer to drop. It is shown that the power-law index and Hartmann reduces the local Nusselt number. Also, the average Bejan numbers corresponding of active parameters are discussed in this study. [ABSTRACT FROM AUTHOR]

Long Duration Balloons are suitable platforms for scientific research to study the Earth and the Solar System. From the thermal point of view, these platforms are analysed at the floating altitude using data of the thermal environmental conditions considering the local characteristics and the seasonal variability. Nevertheless, depending on the launch site conditions and the launch day time, the minimum temperatures could appear during the ascent phase. This is because the balloon-payload system is exposed to free air and the convective heat transfer could drive the thermal behaviour of the onboard equipment. This analysis requires a dynamic study of the balloon trajectory for determining the relative speed with respect to the air as well as an appropriate thermal modelling considering the radiative and convective heat transfer. The aim of this paper is to explain the main characteristics of the ascent phase from a thermal point of view and to show how an ascent phase analysis for a Long Duration Balloon system can be performed using ESATAN-TMS. In order to give examples for the explanation the full process has been particularized to the SUNRISE III mission. • Thermal modelling of a generic payload onboard a Long Duration Balloon for ascent phase analysis. • Determination of the balloon film influence on the payload thermal behaviour. • Determination of the worst-case relative wind speed on the balloon-borne system for forced convection estimations. • Thermal analysis of SUNRISE III mission during the ascent phase using ESATAN-TMS. [ABSTRACT FROM AUTHOR]

This paper aims to numerically investigate the effects of turbulence-inducing elements with various geometries in a double pipe Heat Exchanger (HEX). The water is considered as a working fluid and the flow is turbulent. Also, CFD simulation has been carried out by finite volume method within commercial software. In the first section, the various geometries, including smooth tube, corrugated tube, tube with spherical elements, and a tube with axial fins, are evaluated. Subsequently, the heat transfer characteristics of two various hybrid nanoparticles comprise Ag-MoS 2 and Fe 3 O 4 -SiO 2 , are compared. Ultimately, the optimized geometry has been selected for adding hybrid nanoparticles of Ag-MoS 2 to enhancing heat transfer performance. The obtain results indicate that the double tube heat exchanger with the spherical elements has the best thermal performance. In addition, with changing the Reynolds number from 4000 to 13,000 in the optimized model with Ag-MoS 2 1%, the convective heat transfer coefficient enhances 62.21%. [ABSTRACT FROM AUTHOR]

Highlights • Particle image velocimetry (PIV) was used to capture flow characteristics near heat transfer fins. • A large eddy simulation (LES) provided deeper insight into the flow structures occurring around the fins. • Near wall turbulence and flow patterns responsible for heat transfer enhancement were discussed. • Two unsolved problems on micro-fins were addressed. Abstract Internally enhanced surfaces such as micro-fins are an important class of heat transfer enhancement in commercial applications. Many research papers discuss the design and optima of these surfaces. However, most previous studies have demonstrated only the macro relationship between the geometries of the micro-fins and heat transfer. The need for a deeper understanding of these fins arose from some currently unsolved problems that limit future development of enhanced surfaces. First, why are increases of heat transfer larger than area increases in micro-finned tubes in most cases? Second, why do internally micro-finned tubes typically have lower heat-transfer-enhanced ratios in laminar and transition flows? This work presents a novel method to analyze the detailed relationship between flow characteristics and heat transfer for one type of micro-fin. The goal of the paper was not to find a new Reynolds number-based correlation, but to find flow patterns responsible for heat transfer enhancement and understand the mechanisms that cause this. First, this paper introduces comprehensive experimental measurements including particle image velocimetry (PIV), measurement of the heat transfer coefficient and accuracy of pressure-drop measurements, all used to validate numerical approaches. Validated large eddy simulations (LES) are then used to predict flow characteristics and coherent structures (Q criterion). The numerical simulation includes both heat conduction in the metal structure and heat convection on the solid–fluid interface. Finally, the paper documents how the flow structures link with the enhancement of heat transfer in the micro-finned duct. [ABSTRACT FROM AUTHOR]

Abstract This paper presents analyses of complex flows and heat transfer induced by twin oblique turbulent slot-jets of different directions (divergent, convergent or parallel) impinging a heated wall. A comparison of the heat transfer characteristics between perpendicular and three cases of twin oblique jets (parallel, convergent and divergent). The twin slot jets are located on a confining adiabatic wall at a distance of 8 slot jet width. Convective heat is investigated numerically examining the effect of Reynolds number (Re) and jet inclination angle (α). This problem is relevant to a wide range of practical applications including nuclear engineering devices, manufacturing, material processing, electronic cooling, drying paper or textile, tempering of glass, etc. All computations are performed using two dimensional large eddy simulations (LES) approach with Smagorinsky sub-grid scale (SGS) models. For all directions and inclinations of the jets, the location of the stagnation points is changed and hence, the location and magnitude of the maximum Nusselt number on the heated wall vary. When Reynolds number increases, Nusselt number is improved for all types of inclination. The averaged Nusselt number shows that the perpendicular impingement gives better heat transfer than that of the oblique jets. The poor heat transfer is obtained for the parallel oblique jets. For the same angle, divergent jets give smallest heat transfer than the convergent jets. Graphical abstract Twin-jets flow configuration. (a) Perpendicular (b) Divergent (c) Parallel (d) Convergent. Image 1 Highlights • Four types of flow patterns of impinging twin jet are studied by Large Dissipation Simulation. • Nusselt number is enhanced for all types of inclination for increasing Reynolds number. • Averaged Nusselt number of the perpendicular impingement gives better heat transfer than that of the oblique jets. • The poor heat transfer is obtained for the parallel oblique jets. • For the same angle, divergent jets give smallest heat transfer than the convergent jets. [ABSTRACT FROM AUTHOR]

Highlights • Transport characteristics in porous media are reviewed, including flow and heat transfer. • Transport phenomena of nanofluids are comprehensively summarized, involving heat conduction, convection and radiation. • Transport literatures for the combination of nanofluid and porous medium are classified and concerned. • Phase change heat transfer of nanofluids and porous media are summarized for liquid-gas type and solid-liquid type. • This review involves conduction, convection, radiation and phase change for specified media. Abstract Increasing the heat transfer rate of heat transfer equipment is an ever-lasting topic in thermal engineering. Due to the advantages of light weight, high specific surface, high thermal conductivity, metal foam is a good extending surface for heat transfer enhancement. Nanofluid has a higher thermal conductivity than the traditional base fluid, so it can be used as an efficient heat transfer medium. This paper focuses on various flow and heat transfer modes of nanofluid, metal foam and the combination of the two, with the physical properties of nanofluid and metal foam summarized. The characteristics of flow and heat transfer are introduced. The motivation of this review paper is to arouse the researchers to pay attention to the basic transport understandings for the heat transfer enhancement of nanofluids in porous media. The knowledge reviewed in this paper is useful for improving the performance of compact heat exchangers, and heat sinks for cooling electronics with porous media and nanofluids. [ABSTRACT FROM AUTHOR]

Highlights • Vertical fins contribute to melting by enhancing natural convection mechanism. • Extending fin length is more beneficial than increasing number of fins. • The cases with longer fins could have a higher overall heat transfer coefficient. • The compromise in energy density could be minor due to sensible energy gain. Abstract This paper investigates the effect of vertical fins, as an enhancement technique, on the heat transfer rate and energy density of a latent heat thermal energy storage system. This contributes with knowledge on the interaction of heat transfer surface with the storage material for optimizing storage capacity (energy) and power (heat transfer rate). For the assessment, numerical modeling is employed to study the melting process in a two-dimensional rectangular cavity. The cavity is considered heated isothermally from the bottom with surface temperatures of 55 ˚C, 60 ˚C or 70 ˚C, while the other surfaces are insulated from the surrounding. Aluminum and lauric acid are considered as fin/enclosure material and phase change material, respectively. Vertical fins attached to the bottom surface are employed to enhance the charging rate, and a parametric study is carried out by varying the fin length and number of fins. Thus, a broad range of data is provided to analyze the influence of fin configurations on contributing natural convection patterns, as well as the effects on melting time, enhanced heat transfer rate and accumulated energy. The results show that in addition to increasing the heat transfer surface area, the installation of vertically oriented fins does not suppress the natural convection mechanism. This is as opposed to horizontal fins which in previous studies have shown tendencies to reduce the impact of natural convection. This paper also highlights how using longer fins offers a higher rate of heat transfer and a better overall heat transfer coefficient rather than increasing the number of fins. Also, fins do not only enhance the heat transfer performance in the corresponding melting time, but also maintain similar total amount of stored energy as compared to the no-fin case. This paper discusses how this is the result of the enhanced heat transfer allowing a larger portion of sensible heat to be recovered. For example, in the case with long fins, the relative mean power enhancement is about 200% with merely 6% capacity reduction, even though the amount of PCM in the cavity has been reduced by 12% as compared to the no-fin case. Although the basis for these results stems from the principles of thermodynamics, this paper is bringing it forward with design consideration. This is because despite its importance for making appropriate comparisons among heat transfer enhancement techniques in latent heat thermal energy storage, it has not been previously discussed in the literature. In the end, the aim is to accomplish robust storage systems in terms of power and energy density. [ABSTRACT FROM AUTHOR]

Abstract In this paper, a simple one-dimensional heat transfer model for the nanofluid-based direct absorption parabolic trough collector (NDAPTC) was developed, which was quick to solve, easy to understand, and unnecessary to solve the complicated differential equations. In an actual system, the vacuum condition between the inner tube and glass cover may be changed gradually over time. Therefore, a continuous function for calculating the convective heat transfer in the annulus from near vacuum to atmospheric pressure was established. Combined with it, the derived heat transfer model was suited to evaluating the long-running thermal performance of a NDAPTC quickly. The heat transfer model for a conventional indirect absorption parabolic trough collector (CIAPTC) was also constructed, aiming at comparing the heat transfer processes of this two kinds of collectors. Both the heat transfer models were validated by the test data from the reference. Additionally, the effects of physical parameters, operational and weather conditions on the collector thermal performance were analyzed. It was shown that improvement of the glass transmittance and emittance was crucial to raise the collector efficiency, especially at a higher inlet temperature. The pressure change in the annulus affected the collector thermal performance greatly, thus it tried to avoid the vacuum damage. The collector efficiency was raised with the solar irradiance and ambient temperature increasing and wind velocity reducing, which was more sensible to these weather conditions at a higher inlet temperature and pressure in the annulus. The results in this paper were useful for guiding the collector improvements and engineering designs theoretically, and were beneficial for cleaner production in civil and industrial heat utilization further. Highlights • A one-dimensional heat transfer model for the novel NDAPTC was developed. • A continuous convective heat transfer function in the annulus was derived. • The model was simple and feasible compared to the results from other research. • Effects of glass properties, operation and weather conditions on η c were studied. • The results were useful for evaluating collector long-running thermal performance. [ABSTRACT FROM AUTHOR]

The combination of the high conductivity of nanofluids with the huge accessible surface area of open-cell metal foam would indeed be a superb heat exchange technology. While individual ingredients of this technology have been separately investigated, the combination of the two has received only scant attention. Actually, there are only few studies that are focused on nanofluids flow and heat transfer in metal foam. This paper is intended to serve as an orientation for researchers who are interested in both nanofluids heat transfer and metal foam. The paper thus includes discussion of various aspects of nanofluids and their heat-transfer applications, as well as fundamentals of flow and heat transfer of ordinary fluids in metal foam. A section on recent heat transfer studies in metal foam is included, and another section on pore-scale modeling of transport in metal foam is provided. Nanofluids are presented in terms of their definition, brief history, preparation methods, theoretical models, properties, and engineering applications related to heat transfer. The paper then moves to describe metal foam and its morphology, as well as current understanding and theoretical treatment of flow and heat transfer in this class of highly-porous media. Key heat transfer and flow properties of the foam are outlined. The paper also presents the case for nanofluids forced convection heat transfer in open channels to serve as a background for the more complex case that involves heat transfer in porous media in general. The case of forced convection of nanofluids in metal foam in particular is presented next. Studies including complex effects, e.g. magnetism, are briefly described. Based on the above information, some key findings, conclusions and recommendations are made for interested researches. [ABSTRACT FROM AUTHOR]

• A 3D printer is designed for on-orbit servicing/manufacturing missions. • A thermal control strategy that uses P and fuzzy PI controllers is designed. • The PEEK material is selected to study the thermal control performances. • The simulation results show that the 3D printer is feasible to work on-orbit. On-orbit manufacturing can reduce the cost and time needed by space exploration missions because in-situ maintenance activities can be achieved without the need for additional launches. Furthermore, recent developments in materials science in terms of better mechanical and thermal performance have allowed this application to become a potential reality. However, the deployment of on-orbit manufacturing presents several challenges, including the lack of convective heat transfer and human intervention. This paper proposes an on-orbit 3D printing device capable of operating at a temperature up to 400 °C in the vacuum environment. To validate its feasibility for on-orbit manufacturing, we designed four extruders with different characteristics. We investigated the temperature profiles across the extruders under the vacuum condition through a heat transfer model. Based on the thermal analysis, a thermal control method, which combines the Proportion (P) and Fuzzy Proportion and Integration (Fuzzy PI) strategies, is designed to regulate the 3D printing device operation. With the extrusion rate of 8654.6 mm3 /h and the printing temperature at 400 °C, the melting and solidification status of the PEEK (Polyether ether ketone) material is verified. [ABSTRACT FROM AUTHOR]

Automated Fiber Placement (AFP) is a key additive manufacturing process for the production of complex composite structures. This study focuses on the in-situ AFP process for thermoplastic composites with Hot Gas Torch (HGT), which includes heating, consolidation, and solidification steps. Temperature control is critical to achieving high quality parts as it affects bond quality, crystallization, and solidification. However, previous studies have oversimplified convective heat transfer by assuming a constant coefficient, resulting in discrepancies between simulations and experiments. This paper introduces a novel distribution function to model the convective heat transfer coefficient, thereby improving temperature predictions. An optimization loop is used to determine the parameters of the function, which ensures agreement with experimental data. The proposed approach accurately predicts the temperature distribution, which is validated against unseen experimental results. By incorporating the distribution of the convective heat transfer coefficient, this study improves the understanding of heat transfer mechanisms in AFP for thermoplastic composites, leading to improved manufacturing processes and part quality. [ABSTRACT FROM AUTHOR]

• An unstructured lattice Boltzmann model is proposed to solve radiative transfer in homogeneous media. • The equilibrium distribution function is reconstructed on the interfaces of the unstructured grids. • The unstructured LB model is stable and accurate for steady and transient radiative transfer in homogeneous media with complex geometries. • The unstructured LB model can greatly reduce the computational time compared to the standard LB model. In the past decades, the lattice Boltzmann method (LBM) has been a great success in convection and heat conduction. Recently, based on its advanced numerical properties, LBM has some progress in radiative transfer. Some lattice Boltzmann (LB) models for radiative transfer have been established successively. However, all these LB models for radiative transfer are standard LB models which are limited to uniform Cartesian grids. The unstructured LB model for radiative transfer is still lacking. The unstructured model is important for radiative transfer problems in complex geometric enclosures. Developing an unstructured LB model for radiative transfer is of great significance. This paper proposes an unstructured LB model for radiative transfer in homogeneous media. We establish this model by using the Chapman-Enskog (CE) analysis and the finite volume discretization. In this model, the equilibrium distribution function is reconstructed on interfaces of unstructured grids. Through the CE analysis, we rigorously derive the radiative transfer equation (RTE) from the proposed unstructured LB model. Several numerical cases are conducted to test the performance of the unstructured LB model. Numerical results show that the present unstructured LB model is stable and accurate for solving steady and transient radiative transfer in homogeneous media with complex geometries. Besides, the proposed unstructured LB model can greatly reduce the computational time compared to the standard LB model due to eliminating the streaming process on the uniform lattice. [ABSTRACT FROM AUTHOR]

Ice accretion simulation is an important research technology for aircraft icing problems. Air flow field prediction of an iced aircraft is an essential step of ice accretion simulation. However, commonly used turbulence models have difficulty predicting the large flow separation of the iced aircraft, which makes air flow field calculation insufficiently accurate and further affects the ice accretion simulation. In this paper, the influence of air flow field computation on ice accretion simulation of airfoils is numerically studied. Several different turbulence models are applied to predict air flow fields of iced airfoils. Then, the Eulerian method of water droplets, integral boundary layer method and Myers model are used to simulate ice accretion. Different airfoils with several icing conditions, including glaze ice and rime ice cases, are numerically tested and compared with experimental data. The results show that the separating shear layer fixed k − ω model is more accurate than other turbulence models in predicting the pressure distribution of the iced airfoil, especially the leading-edge suction peak. Thus, a more reasonable droplet collection efficiency distribution and convective heat transfer distribution can be obtained, yielding a more consistent ice height compared with the experimental data. [ABSTRACT FROM AUTHOR]

In the context of the rapid expansion of large-scale subterranean engineering projects, such as underground hydropower stations, mines, and deeply buried subway stations, optimizing heat exchange between air-intake tunnel rock and air has become crucial for enhancing the overall energy efficiency of these underground structures. This study addresses the gap in calculating tunnel heat exchange, particularly the lack of reference values for convective heat transfer and mass transfer coefficients. By analyzing empirical data collected over the past two decades from 14 extensive air-intake tunnels of underground buildings, this paper introduces a novel approach for solving fitting formulas for convective heat transfer coefficients along air-intake tunnels, utilizing empirical data. This methodology utilizes an improved center-moving average data smoothing technique, a comprehensive slope data filtering method, and a novel fitting formula model. It effectively eliminates noise and accurately represents general convective heat transfer behavior within tunnels, especially in the entry segments. Using this method, a fitting formula for the convective heat transfer coefficient along the air-intake tunnel was obtained based on data from 14 tunnels, which can explain 72.3% of data variability. Its reliability was proven using independent measured data. It is tailored for large-scale air-intake tunnels, taking into account actual geometries, wall roughness, entrance effects, and a broad range of wind speeds. The study also presents a dependable method for calculating convective mass transfer coefficients using the proposed fitting formula. The findings provide more precise and practical methods for computing convective heat transfer and mass transfer coefficients in large-scale air-intake tunnels, demonstrating significant practical engineering value. • Method proposed based on large tunnel measurements and detailed data processing. • A calculation method for mass transfer coefficients is also provided and validated. • Convective heat transfer coefficient formula derived from tests data on 14 tunnels. • Study aids ventilation in major underground works like hydropower and mines. [ABSTRACT FROM AUTHOR]

• An enhanced heat transfer structure is proposed, which can improve efficiency by 29 %. • The performance of the new structure was investigated by numerical simulation. • Experimental tests were conducted to prove the effectiveness of the new structure. To enhance the heat transfer efficiency of the helically coiled tubes heat exchangers, this paper proposes a double shell-passes structure designed for a multi-layer helically coiled tubes heat exchanger. Numerical simulation is employed to investigate the performance of the Double Shell-passes Multi-layer Helically Coiled Tubes Heat Exchanger (DSMHCTHE). Furthermore, an experimental test system is constructed to validate the simulation results, exploring the performance under different operating conditions. A comparative analysis is conducted with the traditional Multi-Layer Helical Tube Heat Exchanger (MHCTHE). The results indicate that, under identical experimental conditions, the heat transfer rate and thermal effectiveness of DSMHCTHE increased by 5.1 % to 12.9 %. The overall heat transfer coefficient showed an improvement ranging from 21.5 % to 29.0 %, while the shell-side heat transfer coefficient increased by 36.2 % to 47.5 %. However, the shell-side pressure drop increased by 60.7 % to 83.4 %. Utilizing the heat exchanger's comprehensive performance as the evaluation criterion, it was observed that DSMHCTHE exhibited superior comprehensive performance. In comparison to MHCTHE, the comprehensive performance of DSMHCTHE improved by 12 %. The design of the double shell-passes configuration has shown significant enhancements in both convective heat transfer and overall performance, highlighting the superior application potential of DSMHCTHE. [ABSTRACT FROM AUTHOR]

The following paper presents a simple method of determining the presence, distribution and values of heat losses from external building walls as thermodynamic partitions using a Thermal Imaging Camera (TIC). According to Fourier's equation, the value of heat loss is proportional to the temperature gradient ∂ t /∂ y | y=0 in air in the y direction perpendicular to the heated surface. Unfortunately, air temperature cannot be measured with a TIC, as gases do not emit thermal radiation. It is therefore suggested that a grid placed vertically in the air and perpendicularly to the heated surface should be used as a detector of temperature field. Warmed by convective air flows, such a grid becomes a source of infrared radiation. The temperature distribution reproduced on the grid constructed from thin strands of a low thermal conductivity material is sufficiently distinct and sharp to be recorded with a TIC. The correctness of the TIC method has been tested in laboratory conditions on the example of a vertical heating plate, as well as in real-life conditions − on a single pane of glass serving as a building partition. When compared to the works of other authors, the result obtained as Nu  = 0.571· Ra 0.25 relation reveals a satisfactory correlation for the heating plate, while estimated temperature distributions and heat fluxes from the room to the surface of thermodynamic partition wall Q loss,conv,in and on the outside of the building Q loss,conv,ext successfully and quite precisely correlate (5–7% for both internal and external sides) with theoretical calculations. Therefore, the TIC method proposed in this paper can significantly extend the range of application of TICs in energy audits, especially for buildings [ABSTRACT FROM AUTHOR]

This review paper presents an overview of transpired solar collectors (TSCs) - a clean energy technology that has gained considerable attention due to its potential to minimise building energy demand and contribute to achieving net zero emissions. The review is mainly focused on scrutinising the disparities in heat and mass transfer mechanisms, specifically the impact of homogeneous and inhomogeneous suction flow distributions on the TSC, encompassing performance improvement methods, performance assessment, and optimisation strategies for TSCs. The inconsistency between the theoretical and real-world performance of TSCs was observed, attributed to the high turbulence wind with non-uniform speed distribution and suction flow interactions with the main flow in the plenum. Corrugations on the absorber improved thermal performance but increased wind heat loss on the exterior surface, which could be mitigated by adding glazing to corrugated TSCs. The review highlighted the flexibility of integrating TSCs with other technologies, including coupling with separate phase change material (PCM) thermal energy storage units, which outperformed those placing the PCM plate into the plenum. Moreover, integrating TSCs with desiccant wheel cooling systems showed some interesting results in terms of cost and payback period, while integration with heat pump systems could reduce electricity consumption, but it was not recommended in cold climates. Exergetic analysis has been frequently used to determine thermodynamic losses of TSCs and it could provide a more accurate performance assessment when integrating TSCs with power generation systems. The review identified several research gaps in related study fields and provided recommendations, encompassing dimensionless analysis of the relationships between wind effect and heat transfer of TSC absorbers, the development of convective heat transfer correlations for TSC's absorber, and the exploration of cost-effective design and optimisation strategies for hybrid TSCs. • Heat and mass transfer mechanisms of transpired solar collectors (TSCs) were analysed. • TSCs can be integrated with different energy technologies to improve flexibility. • Various designs of TSC systems and their main design parameters were discussed. • It provides some insights into developing convective heat transfer correlations. [ABSTRACT FROM AUTHOR]

• Performance evaluation of three different cooling methods for data centers is conducted. • Single-phase immersion cooling has advantages in heat transfer and energy consumption. • Correlation between oil properties and immersion cooling performance is established. • Dynamic viscosity has the greatest impact on the flow and thermal performance of oil coolants. This paper conducts a comprehensive performance evaluation and optimization of single-phase immersion cooling (SPIC) systems to address challenges in data center server cooling. A three-dimensional model of blade servers with different cooling methods is constructed and numerically solved to compare thermal transport performance, flow characteristics, and energy consumption performance. Furthermore, the influence mechanisms of different oil coolants and operating conditions on SPIC system performance are studied. The results indicate that the SPIC scheme exhibits significant advantages in terms of heat transfer capability, heat transfer uniformity, and flow resistance loss. Moreover, the power usage effectiveness (PUE) of SPIC systems decreases by 20.8 % and 17.6 % compared to forced air cooling and water cooling plate solutions, respectively. The dynamic viscosity of oil coolants has the greatest impact on the SPIC performance. Moreover, high-viscosity silicone oil increases the flow resistance of SPIC systems and weakens the convective heat transfer capability between the coolant and components. By ensuring safe operation, increasing the inlet temperature of oil coolants reduces flow resistance losses and enhances heat transfer capacity. Additionally, initially increasing the mass flow rate improves convective heat transfer capacity. However, the heat transfer improvement gradually diminished beyond a certain threshold while flow resistance losses increased significantly. [ABSTRACT FROM AUTHOR]

The electronics in logging tools are susceptible to thermal failure due to the extreme thermal environment. Passive thermal management system (PTMS) has been proven to protect the electronics for several hours. In this paper, a numerical model based on the equivalent thermal conductivity method was developed to determine the transient temperature of downhole electronics. Compared with the traditional analytical model or numerical model considering only one single heat transfer process, the complex heat transfer in the logging tool were comprehensively considered through the proposed model. Briefly, the heat transfer processes in the vacuum bottle were theoretically calculated rather than empirically acquired, and the convective and radiative heat transfer inside the vacuum bottle was equated to the temperature-dependent thermal conductivity of air. In addition, the proposed numerical model was compared with experiments and previous numerical models to verify the accuracy of the model, and the temperature deviation of the electronics was within 5 °C. Moreover, the computational time was greatly reduced compared with the traditional three-dimensional numerical simulation process while ensuring the accuracy of calculation. Therefore, the proposed numerical model achieved both computational accuracy and efficiency, which was expected to be widely used in the development of PTMS for logging tools. • A numerical model based on equivalent thermal conductivity method was proposed. • The complex heat transfer processes in PTMS were comprehensively considered. • The proposed model possessed high computational accuracy and efficiency. [ABSTRACT FROM AUTHOR]

At present the ion-wind has been applied to portable electronic equipment heat dissipation because of its excellent heat dissipation performance. In this paper, sawtooth-mesh and sawtooth-plate ion-wind generators are studied. In addition, the best structure of single-stage ion-wind is found through the local maximum velocity, average velocity, and average mechanical efficiency.For single-stage sawtooth-mesh ion wind generator,when the number of sawteeth is 6 and the electrode gap is 20 mm,the average velocity that can achieve the best ion wind 1.7 m/s, and the average mechanical efficiency is 0.84%.For single-stage sawtooth-plate ion wind generation devices.When the number of sawteeth is 4 and the electrode gap is 15 mm.The average wind velocity of ion wind can reach 1.42 m/s, and the average mechanical efficiency is 1.14%.On this basis, the multi-stage sawtooth-plate ion-wind generator is studied. The more number of stages, the higher the average velocity of ion-wind is, but when the number of the stage is more than 2, the average mechanical efficiency decrease then the practicality is limited.When the number of multistage electrode stages is 2, the average heat transfer coefficient can reach 86.1 W/m-2·K-1, which is 34% higher than the single-stage structure. [ABSTRACT FROM AUTHOR]

This paper presents a model of heat and moisture transfer through multilayer firefighter protective clothing, which for the first time has taken into account all the major heat and moisture transport mechanisms including conductive and convective heat transfer, two-flux radiative heat transfer, moisture bulk flow, moisture absorption/desorption by fibers, moisture diffusion and phase change. The model was solved by Crank–Nicolson scheme of the finite difference method. Numerical analysis showed that our model can accurately predict the second-degree burn time with an error ranging from 0.37% to 3.55% for different types of clothing assemblies. With this model, the distributions of heat and moisture within the protective clothing system are elucidated and the relative importance of key clothing parameters on thermal protection better understood. It revealed that the thickness of the moisture barrier layer has the greatest influence on the skin burn time. This study is significant in providing a theoretical framework for optimizing the design of thermal protective clothing. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive investigation of heat transfer enhancement and pressure drop in a Coiled Flow Reverser (CFR) with a twisted tape insert. Both laminar (10 < Re < 2000) and turbulent (12,000 < Re < 18,000) regimes have been studied using both experimental and numerical methods. The effects of twist ratio of twisted tape, inlet Reynolds number, and perforating the twisted tapes have been investigated. The study found that the best performance in the laminar regime is achieved with a twisted tape with a twist ratio of 15.73 and no holes on it at a Reynolds number of 2000. In the turbulent regime, the same twisted tape performs the best at a Reynolds number of 17,000. The highest Thermal Performance Ratio (TPR) in laminar regime is 1.55 and in turbulent regime is 0.99. In comparison to the straight pipe, all types of CFRs show better performance in heat transfer enhancement. Also, as the Reynolds number increases, the friction coefficient decreases in all configurations. The study reveals that the twisted tape insert enhances heat transfer performance while increasing pressure drop. This study provides valuable insights into the design and optimization of heat exchangers with CFR. The findings can be used to improve the efficiency and performance of various industrial processes, such as refrigeration systems, air conditioning, and power plants. • Fluid flow and heat transfer in a coiled flow reverser (CFR) were studied. • Effects of tube insert on the heat transfer enhancement of CFR were investigated. • Effects of perforation of tube insert on heat transfer enhancement of CFR were examined. • The effects of tube insert at laminar flow are more than turbulent flow. • Perforation has no significant effects on the thermal performance ratio. [ABSTRACT FROM AUTHOR]