Search

At present, dynamic simulation and analysis on building thermal environment and energy consumption achieved by computer software become a reality. However, it is found that defined gaps exist between simulation and on-site measurement. To explore the gaps, this paper takes typical air-conditioned university dormitories located in Chongqing as a case study. Simultaneously, the gaps are explored with a DeST-h building energy simulation model and on-site measurement. Indicators including indoor temperature, relative humidity and air conditioning energy consumption under different setting temperature are simulated and measured. Then, a comparison between simulation results and measured data is explored as well as the cause of these gaps. This paper studies thermal environment and energy consumption by combining on-site measurement and numerical simulation, and the conclusion is that the gaps can from occupant behaviour and physical parameters of the indoor and outdoor environment, which provides a reference for thermal environment of the dormitory and building simulation. [ABSTRACT FROM AUTHOR]

With increased use of variable refrigerant flow (VRF) systems in the U.S. building sector, interests in capability and rationality of various building energy modeling tools to simulate VRF systems are rising. This paper presents the detailed procedures for model calibration of a VRF system with a dedicated outdoor air system (DOAS) by comparing to detailed measured data from an occupancy emulated small office building. The building energy model is first developed based on as-built drawings, and building and system characteristics available. The whole building energy modeling tool used for the study is U.S. DOE’s EnergyPlus version 8.1. The initial model is, then, calibrated with the hourly measured data from the target building and VRF-DOAS system. In a detailed calibration procedures of the VRF-DOAS, the original EnergyPlus source code is modified to enable the modeling of the specific VRF-DOAS installed in the building. After a proper calibration during cooling and heating seasons, the VRF-DOAS model can reasonably predict the performance of the actual VRF-DOAS system based on the criteria from ASHRAE Guideline 14-2014. The calibration results show that hourly CV-RMSE and NMBE would be 15.7% and 3.8%, respectively, which is deemed to be calibrated. The whole-building energy usage after calibration of the VRF-DOAS model is 1.9% (78.8 kWh) lower than that of the measurements during comparison period. [ABSTRACT FROM AUTHOR]

The area of projected shadow on building facades may play a role of paramount importance in the prediction of solar energy conversion and building thermal and energy performance. Algorithms for solar shading calculations may directly affect the accuracy of results obtained by building energy simulation tools. In addition, the consideration of uncertain design parameters imply an estimative of a confidence interval of solar fraction results that determine the reliability as well as the improvement of shading calculation models. In this way, this paper presents a methodology for uncertainty and sensitivity analysis applied to the prediction of sunlit area on building exterior surfaces with shading devices. From a single building model, the solar fraction was investigated for two cities and four typical days. According to the obtained results, more than 20% of all simulation time steps have uncertainties equal or higher than 5% on the solar fraction calculation at 95% confidence level. The maximum values of the uncertainties occur in warmer months, which could significantly impact the building energy balance. Three inputs have higher influence on the uncertainties on solar fraction results: (1) latitude, (2) orientation and (3) width of overhang fins. Perturbation of only 5° on the building orientation may imply important uncertainties on solar fraction, which is normally neglected by designers. The results highlight the importance of assessing the uncertainty of inputs in algorithms such as the one to calculate the surface solar fraction that is an important prerequisite of the final building energy balance. [ABSTRACT FROM AUTHOR]

Abstract: This paper aims to validate and improve three cross and single-sided natural ventilation models implemented in a whole-building hygrothermal and energy simulation program. The tested models are the British Standard for cross ventilation, the de Gids and Phaff's and Larsen's for single-sided ventilation. Airflow rates obtained by those models have been compared to the measurements performed in two full-scale buildings: one single room house located in a wind tunnel facility and one real three-storey building. Results show a large variation of airflow rates provided by the different models. The Larsen's model can be improved if coupled to the CPCALC algorithm, providing better results for both wind tunnel and on-site experiments. [Copyright &y& Elsevier]