Search

This paper describes an accurate model of the Electrical Power Subsystem (EPS) of the Thermal Analysis Support and Environment Characterization Laboratory (TASEC-Lab), a university experiment developed for using in high-altitude balloon missions to measure and analyze the convection heat transfer. A Li-ion battery and two high efficient DC–DC converters have been characterized through laboratory tests and fitting to the experimental results. The developed mathematical models described in this paper are used to carry out accurate EPS simulations and are validated by comparison with the experimental data. • Design and modeling of the electrical power subsystem of a stratospheric balloon experiment. • New Li-lion battery discharging model that describes the three main parts: initial decay, linear, and exponential decay. • Formulation of a new DC/DC converter efficiency model. • Simulation and model validation of the electrical power subsystem. [ABSTRACT FROM AUTHOR]

The numerical modelling of the internal heat generation in passenger vehicle tyres using finite element analysis is a well-known numerical approach. However, this application is rather uncommon for earthmover tyres. This paper describes the development of a finite element model of a 23.5R25 earthmover tyre for the numerical modelling of the temperature distribution in the tyre cross-section at steady-state heat transfer conditions using an uncoupled analysis procedure. Considering the non-linear behaviour of the rubber compounds used for the manufacturing of these tyres, as well as the complexity associated with the composite structural aspects of the tyre, the material properties used for the proposed numerical model were established experimentally. In the analyses completed, the tyre behaviour was studied by simulations at various inflation pressures, loads and rolling velocities. The numerical tyre defection was within an 8% deviation from the actual tyre behaviour. Thermal simulation results were used to derive an equation that can be used to predict the maximum temperature that would occur in the tyre’s cross-section as a function of its vertical deflection, its forward rolling velocity and the ambient temperature of the surroundings. The numerical models and simulations presented in this paper were completed using MSC.Marc/Mentat. [ABSTRACT FROM AUTHOR]

Heat losses from a building foundation are affected by both the surrounding conditions and the surrounding soil properties. These include many factors that complicate the analysis of heat loss, such as thermal storage, snow and soil freezing. The effect of snow and soil freezing was studied with a 3D simulation model in a subarctic climate. The heat losses from the most commonly used foundation types in Sweden were studied. This paper shows that it is possible to achieve a good thermal estimation of the air temperatures in a crawl space, with an average difference of 0.4 °C compared with the validation data over a year. Snow and soil freezing reduce the annual heat losses through the different foundation types by 7–10% and the maximum heat loss rate by 13–25%. In order to describe the heat transfer correctly, snow must be included in the calculations, while soil freezing has only a minor impact. The 3D model implemented in this study shows a significant impact on the soil temperatures when these parameters are included. For a subarctic climate, the commonly used calculation methods based on the European standard ISO 13370 are not thorough enough to calculate the heat transfer through a foundation accurately. [ABSTRACT FROM AUTHOR]

In the present investigation, a non-linear mathematical model is developed for the analysis of Septuple effect flat falling film evaporator (SEFFFE) system used for concentrating black liquor in a nearby paper mill. This model is capable of simulating process of evaporation considering variations in boiling point rise (τ), overall heat transfer coefficient (U), heat loss (Q loss), flow sequences, liquor/steam splitting, feed, product and condensate flashing, vapor bleeding and physico-thermal properties of the liquor. Based on mass and energy balance around an effect a cubic polynomial is developed and solved repeatedly in a predetermined sequence using generalized cascade algorithm. For development of empirical correlations for τ, U and Q loss, plant data have been collected from SEFFFE system. These correlations compute τ, U and Q loss within average absolute errors of 2.4%, 10% and 33%, respectively, when their results are compared with the plant data. [Copyright &y& Elsevier]

Abstract: Along with the developments of lattice-Boltzmann method in simulation of fluid flow, its thermal features should be also improved. An important problem which is encountered in many cases is the conjugate heat transfer or heat transfer at the fluid–solid interface. In this case, a strict technique is required to calculate the heat exchange between fluid and solid. Only a few works have been published regarding this phenomenon. In this paper, we have presented a model for analysis of the conjugate heat transfer. The model has been validated by two benchmarks: (I) Fluid flow and heat transfer in a backward-facing step channel with heated thick wall, and (II) Fluid flow and heat transfer in a channel with infinite number of heated obstacles mounted on the wall. The numerical tips concerned in the simulation of these problems by lattice-Boltzmann method have been also represented in the paper. [Copyright &y& Elsevier]

Abstract: This paper discusses results of simulations conducted for non-contacting face seals showing the influence of the operational parameters on the distributions of temperature in the structural elements and the fluid film separating the sealing rings. The mathematical model developed for noncontacting face seals consists of cross-coupled differential equations with partial derivatives. We solved it analytically, taking into account various boundary conditions. The heat equations were solved using the method of separation of variables. The derived relationships were based on Bessel functions of the first and second kinds. By defining the relationships describing the distributions of temperature in the sealing rings and the fluid film separating them, we could determine the effect of the operational parameters on the variability of temperature fields. Confirmation of the simulation results with experimental data is essential to better recognize the phenomena taking place in the sealing assembly and improve the design of non-contacting seals so that they can be used in various industrial applications. In this paper, we also describe a specially designed test stand for compensation of the misalignment of the flexibly mounted ring and automatic control of the radial clearance height. The test stand can also be used to verify the results of analytical studies. [Copyright &y& Elsevier]

Abstract: Snow cover is a common and relatively stable land cover condition in winter for cold north regions in China. Snow cover has significant effects on water and heat transfers in frozen soil; it needs to be considered in the study of frozen soil water–heat coupled movements. On the basis of previous research results and physical process analysis of water and heat movements in snow cover and soil, a snow cover–soil union water–heat coupled movements model is established in this paper. The numerical simulation was conducted by using a finite difference method. The results indicate that the simulated values have a similar trend to the measured values and the numerical simulation had big relative errors. However, the average absolute errors of the total and liquid moisture content in frozen soil were all less than 4%, and that of the frozen soil temperature was 1.37 °C. The errors of the numerical simulation were still within the acceptable range. Thus, the snow cover–soil union water–heat coupled movement model constructed in this paper is rational. [Copyright &y& Elsevier]

Abstract: Agricultural residues (agro-biomass) can produce energy by thermochemical conversion. Gasification is becoming one of the best clean technologies for power production. Thermochemical process of gasification sets free the solid fuel inherent energy and converts the solid phase into a mixture of gases (producer gas or syngas) that carries a percentage of this energy. Fluidized bed reactors may be used for biomass gasification offering many advantages such as: (1) the superior mixing properties and (2) the enhanced heat transfer rates between the gas and the particles as well as between the particles and the heat exchanger surfaces. In this paper gasification process applied to agricultural residues is reviewed by means of modelling. Description of various stages of the biomass gasification in a fluidized bed is made and the whole spectrum of problems from the processes in an individual biomass particle (drying, pyrolysis, fragmentation and charl burning) to the global mass transfer and chemical processes in a fluidized bed reactor and freeboard is presented. The paper discusses also the specific problems arising from using agricultural residues as raw material and recommends further experimental studies necessary for process optimisation and for scale up. Extensive investigation of gasification plant behaviour depending on various operating parameters is always required in order to support the optimisation procedure and mathematical models are helpful to reduce the temporal and financial efforts. [Copyright &y& Elsevier]

Abstract: Adequate modeling of radiation heat transfer is important in CFD simulation of coal gasification process. In an entrained-flow gasifer, the non-participating effect of coal particles, soot, ashes, and reactive gases could significantly affect the temperature distribution in the gasifier and hence affects the local reaction rate and life expectancy of wall materials. For slagging type gasifiers, radiation further affects the forming process of corrosive slag on the wall which can expedite degradation of the refractory lining in the gasifier. For these reasons, this paper focuses on investigating applications of five different radiation models to coal gasification process, including Discrete Transfer Radiation Model (DTRM), P-1 Radiation Model, Rosseland Radiation Model, Surface-to-Surface (S2S) Radiation Model, and Discrete Ordinates (DO) Radiation Model. The objective is to identify the pros and cons of each model’s applicability to the gasification process and determine which radiation model is most appropriate for simulating the process in entrained-flow gasifiers. The Eulerian–Lagrangian approach is applied to solve the Navier–Stokes equations, nine species transport equations, and seven global reactions consisting of three heterogeneous reactions and four homogeneous reactions. The coal particles are tracked with the Lagrangian method. Six cases are studied—one without the radiation model and the other five with different radiation models. The result reveals that the various radiation models yield uncomfortably large uncertainties in predicting syngas composition, syngas temperature, and wall temperature. The Rosseland model does not yield reasonable and realistic results for gasification process. The DTRM model predicts very high syngas and wall temperatures in the dry coal feed case. In the one-stage coal slurry case, DTRM result is close to the S2S result. The P1 method seems to behave stably and is robust in predicting the syngas temperature and composition; it yields the result most close to the mean, but it seems to underpredict the gasifier’s inner wall temperature. [Copyright &y& Elsevier]

Abstract: This paper presents results obtained from a numerical simulation for the horizontal slinky-loop heat exchanger of a ground-source heat pump system. A three-dimensional numerical model was developed and the results of the thermal performance of various heat exchanger configurations are presented. The investigation was carried out on five types of loop pitch (loop spacing), three types of loop diameter, three values of soil thermal properties, and allowing continuous and intermittent operation. Comparison was made for the heat transfer rate, the amount of pipe material needed, as well as excavation work required for the horizontal slinky-loop heat exchanger. The results indicate that system parameters have a significant effect on the thermal performance of the system. [Copyright &y& Elsevier]

Abstract: This paper investigates the numerical simulation of non-Fourier transient heat transfer in a two-dimensional sub-100nm metal-oxide-semiconductor field-effect transistor (MOSFET). The dual-phase-lag (DPL) model with a specific normalization procedure is introduced for the modeling of nanoscale heat transport. The boundary conditions are selected similar to what existed in a real MOSFET device, both uniform and non-uniform heat generations within the transistor are applied, and the end parts of the top boundary which are in contact with the metallic material are left open. A temperature-jump boundary condition is used on all boundaries in order to consider the boundary phonon scattering at micro and nanoscale. A three-level finite difference scheme has been employed to generate the numerical results which are illustrated for a silicon sub-100nm MOSFET corresponding to the Knudsen number of 10. The results are presented at real times less than 50ps to avoid the three-dimensional effects. It is concluded that the combination of the DPL model with mixed-type temperature boundary condition is able to predict the heat flux and temperature distribution obtained from the Boltzmann transport equation (BTE) more accurate than the ballistic-diffusive equations (BDE). After verification of our results, the thermal field and the hotspot temperature within the bulk silicon are presented and the effect of adding a layer of silicon-dioxide to the transistor on its thermal behavior has been investigated. [Copyright &y& Elsevier]

Abstract: Dynamic simulations of distillation columns are widely used to develop effective control structures. The normal distillation models assume instantaneous heat transfer in the condenser and reboiler. However, when dynamic simulations are used in the analysis of safety problems in the event of emergency situations, the basic model does not accurately represent the dynamic response. Accurate response times are essential in the design of safety systems for the column. For example, a failure of the supply of cooling water will lead to rapid increases in pressures and temperatures that occur in seconds. Accurately determining the rates of increase in these important variables and the time period to reach critical limits (safety response time) permits the engineer to quantitatively design effective safety systems. This paper illustrates how rigorous condenser and reboiler models can be developed in Aspen Plus and their dynamics evaluated in Aspen Dynamics. [Copyright &y& Elsevier]

Abstract: This paper proposed a new method based on modified composite model in the thermal response test (TRT) in the variable heat rate case study. The new method considered the unsteady-state heat transfer in the borehole instead of the line-source model assumption. A Matlab program was compiled which can perform inversion calculation to obtain the ground thermal properties. The superposition principle was used to process the variable-rate problem. This new method was applied to two thermal response tests. The simulation value based on the method shows a good agreement with the measurement data of water temperature. The proposed method would save the time and reduce the cost of TRT when power fluctuation or failure occurs. [Copyright &y& Elsevier]

Abstract: In this paper, a three-dimensional hydrogen absorption model is developed to precisely study the hydrogen absorption reaction and resultant heat and mass transport phenomena in metal hydride hydrogen storage vessels. The 3D model is first experimentally validated against the temperature evolution data available in the literature. In addition to model validation, the detailed 3D simulation results show that at the initial absorption stage, the vessel temperature and H/M ratio distributions are uniform throughout the entire vessel, indicating that hydrogen absorption is very efficient early during the hydriding process; thus, the local cooling effect is not influential. On the other hand, non-uniform distributions are predicted at the subsequent absorption stage, which is mainly due to differential degrees of cooling between the vessel wall and core regions. In addition, a parametric study is carried out for various designs and hydrogen feed pressures. This numerical study provides a fundamental understanding of the detailed heat and mass transfer phenomena during the hydrogen absorption process and further indicates that efficient design of the storage vessel and cooling system is critical to achieve rapid hydrogen charging performance. [Copyright &y& Elsevier]

Abstract: This paper investigates the transient heat conduction around the buried spiral coils which could be applied in the ground-coupled heat pump systems with the pile foundation as a geothermal heat exchanger. A transient ring-coil heat source model is developed, and the explicit analytical solutions for the temperature response are derived by means of the Green’s function theory and the image method. The influences of the coil pitch and locations are evaluated and discussed according to the solutions. In addition, comparisons between the ring-coil and cylindrical source models give that the improved finite ring-coil source model can accurately describe the heat transfer process of the pile geothermal heat exchanger (PGHE). The analytical solutions may provide a desirable and better tool for the PGHE simulation/design. [Copyright &y& Elsevier]

Abstract: This paper introduces the chattering problem in dynamic mathematical two-phase flow models. The real system object of study is also introduced, the DISS test facility, a parabolic-trough solar power plant using as heat transfer fluid the steam–water mixture. A dynamic model for studying its behaviour was previously developed using Modelica as the modelling language, in this model the chattering problem arises and therefore not allowing to take full advantage of dynamic simulations. The chattering problem increases the computational time needed for simulation and sometimes dynamic simulations do not finish at all. A heuristic method, which minimises the effects of the chattering problem, is discussed and results which reduce the computational time for dynamic simulations are given. [Copyright &y& Elsevier]

Abstract: This paper focuses on the investigation of the 3D mathematical model to simulate the coupled heat and liquid moisture transfer in hygroscopic porous fibrous media. The flow of the liquid moisture, the water vapor sorption/desorption by fibers and the diffusion of the water vapor are taken into account in this 3D model. Prediction-corrector method is used to solve the 3D governing equations. A series of computational results of the coupled heat and moisture transfer are obtained with the specific initial conditions and boundary conditions. The distribution of the water vapor concentration in the void spaces, the volume fraction of the liquid water in the void spaces, the distribution of the water content in fibers and the changes of the temperature in porous fibrous media are computed. It is shown that the effects of the gravity and capillary actions are significant in hygroscopic porous fibrous media. The comparison with the experimental measurements shows the reasonable agreement between the two. The results illustrate that the 3D model of the coupled heat and liquid moisture transfer in hygroscopic porous fibrous media is satisfactory. [Copyright &y& Elsevier]

Abstract: It has been well established that heat transfer in a helical coil is higher than that in a corresponding straight pipe. However, the detailed characteristics of fluid flow and heat transfer inside helical coil is not available from the present literature. This paper brings out clearly the variation of local Nusselt number along the length and circumference at the wall of a helical pipe. Movement of fluid particles in a helical pipe has been traced. CFD simulations are carried out for vertically oriented helical coils by varying coil parameters such as (i) pitch circle diameter, (ii) tube pitch and (iii) pipe diameter and their influence on heat transfer has been studied. After establishing influence of these parameters, correlations for prediction of Nusselt number has been developed. A correlation to predict the local values of Nusselt number as a function of angular location of the point is also presented. [Copyright &y& Elsevier]

Abstract: This paper presents experimental and numerical studies of the pressure drop in ceramic foams for solar air receiver applications. There are three main aims in this study. The first is to measure the pressure drop in the studied ceramic foams, and to build an empirical model based on the experimental results and a parametric numerical simulation. The second aim is to study flow field characteristics in the ceramic foams, especially in the vicinity of the interface. The third is to study the pressure drop characteristics of two modified structures (by manufacturing holes on the ceramic foams) that are expected to decrease the pressure drop in ceramic foams, but maintain good heat transfer properties. The experimental results from the samples, including two modified structures, along with the simulation results, show that the pressure drop in the ceramic foams follows a modified Darcy relationship. The experimental results also show that the two modified structures dramatically decrease the pressure drop (with pressure drop decreases up to 70% at a superficial velocity of 5m/s). Based on both the experimental and the simulation results, a generalized model for predicting the pressure drop in ceramic foams was proposed. [Copyright &y& Elsevier]

Abstract: In the present study, a 3D numerical simulation of a whole heat exchanger with middle-overlapped helical baffles is carried out by using commercial codes of GAMBIT 2.3 and FLEUNT 6.3. At first, the computational model and numerical method of the whole heat exchanger with middle-overlapped helical baffles is presented in detail, and parallel computation mode is adopted for the simulation of a whole heat exchanger with six cycles of the middle-overlapped helical baffles of 40° helical angle on a grid system of 13.5-million cells; second, the validation of the computational model is performed by comparing the total pressure drop and average Nusselt number of the whole heat exchanger with experimental data. Reasonably good agreement is obtained, and the reasons causing to the discrepancy are analyzed. The shell-side fluid pressure and temperature fields of the whole area are then presented. Finally the cycle average Nusselt number of different cycle in the heat exchanger are compared and it is found that within the accuracy allowed in engineering computation, periodic model for one cycle can be used to investigate the heat transfer and pressure drop characteristics for different heat exchanger to save computational source. The companion paper will provide details of simulation results using the periodic model for different helical angles and different structures of helical baffles. [Copyright &y& Elsevier]

Abstract: An improved understanding of the heat transfer in materials consisting of two layers (splat and substrate) is essential for many industrial applications. We are interested in the deposition, rapid cooling and solidification of metal droplets (known as splats) brought into contact with a cold substrate. We therefore need to understand the temperature history in both the splat and the substrate, including phase change phenomena. A new model of the thermal contact resistance based on a random distribution of contact points, rather than the uniform distribution commonly used, is presented in this paper. Phase change has been also considered, using the enthalpy-porosity formulation. Simulations have been conducted with the commercial package CFX-4. The computational results for the cooling rate of the splat obtained using the random contact distribution model are in good agreement with available experimental results. In addition, results obtained from the random model provide information on the inhomogeneity affecting the temperature at the interface between the splat and the substrate. [Copyright &y& Elsevier]

Abstract: Understanding the heat and mass transfer phenomena in a coal gasifier is very useful for the assessment of gasifier performance and optimization of the design and operating parameters. In this paper, performance of an entrained flow air blown laboratory scale gasifier is numerically simulated with Fluent software. In the model, the continuous phase conservation equations are solved in an Eulerian frame, while those of particle phase are solved in a Lagrangian frame, with coupling between the two phases carried out through interactive source terms. The dispersion of the particles due to turbulence is predicted using a stochastic tracking model, in conjunction with the k–ε equations for the gas phase. The coal gasification model adopted includes devolatilization, combustion of volatiles, char combustion and gasification. The gasification performance inside the gasifier has been predicted for different air ratios as well as for different air and steam inlet temperatures. The overall temperature inside the gasifier is found to increase when the degree of air/steam pre-heating is increased, resulting in acceleration of the different reaction steps in the gasifier. The overall gasification performance indices such as carbon conversion, heating value of the exit gas and cold gas efficiency have been predicted. The predicted results show good agreement with available experimental data in literature. [Copyright &y& Elsevier]

Abstract: The paper presents the geometry of infinite regular polyhedrons that can be used to construct the heat exchange units. The basic structural component of the infinite solid consists of six hexagons, which meet in the common vertex. The mathematical model of heat and mass transfer inside the labyrinth heat exchanger is shown. The first and the second Kirchhoff’s laws are used to simulate fluid flow distribution at hydraulic network created with connected basic solids. Heat balance equations are adopted to describe forced convection heat transfer inside developed heat exchanger. Good accordance among the experimental data and calculation results over whole simulation range is obtained. The efficiency and thermal characteristic of the labyrinth heat exchanger is presented in the form of graphs. [Copyright &y& Elsevier]

Abstract: This paper presents the advantages of a Branch Eigenmodes Reduced Model used in a control process of a heating system. The experimental setup is a 3D heat conductive system in which a heat source is set. First, the reduced model is used to solve the non-linear Inverse Heat Conduction Problem: identification of the heat source strength variations from time-varying temperatures. Then, the reduced model is used to control hot points in the system. The objective of the method is to allow sequential temperature control by decreasing the computation time necessary for the simulation. [Copyright &y& Elsevier]

Abstract: In this paper, a rigorous MILP formulation for grass-root design of heat exchanger networks is developed. The methodology does not rely on traditional supertargeting followed by network design steps typical of the Pinch Design Method, nor is a non-linear model based on superstructures, but rather gives cost-optimal solutions in one step. Unlike most models, it considers splitting, non-isothermal mixing and it counts shells/units. The model relies on transportation/transshipment concepts that are complemented with constraints that allow keeping track of flow rate consistency when splitting takes place and with mechanisms to count heat exchanger shells and units. Several examples from the literature were tested, finding that the model usually obtains better solutions. In some cases, the model produced unknown solutions that were not found using superstructure optimization methods, even when the same pattern of matches is used. [Copyright &y& Elsevier]