Search

The current technologies to treat hypersaline produced water (PW), such as thermal evaporation, are usually energy-intensive and cost-prohibitive. This study developed a low-cost, robust, solar-driven carbon black and airlaid paper-based evaporator (CAPER) for desalination of PW in the Permian Basin, United States. The study aims to better understand the removal of aromatic organic compounds and heavy metals during solar distillation, water output, and heat transfer. Outdoor experiments using CAPER assisted with polystyrene foam in a single slope, single basin solar still achieved an enhanced average evaporation rate of 2.23 L per m2 per day, 165% higher than that of a conventional solar still. Analysis of heat transfer models demonstrated that CAPER solar evaporation achieved an evaporative heat transfer coefficient of ∼28.9 W m−2·K−1, 27.9% higher than without CAPER. The maximum fractional energy of evaporation and convection heat transfer inside the solar still with and without CAPER was ∼81.4% and ∼78.2%, respectively. For the PW with a total dissolved solids concentration of 134 g L−1, solar distillation removed 99.97% salts and over 98% heavy metals. The high removal efficiency of 99.99% was achieved for Ca, Na, Mg, Mn, Ni, Se, Sr, and V. Organic characterization revealed that solar distillation removed over 83% aromatic compounds. Solar desalination using CAPER provides a low-cost and high-performance process to treat PW with high salinity and complex water chemistry for potential fit-for-purpose beneficial uses. Image 1 • A carbon black and airlaid paper-based solar evaporator (CAPER) was developed. • Outdoor distillation of produced water (PW) achieved evaporation of 2.23 L m−2·d−1. • The evaporation rate of PW with CAPER is 165% higher than without CAPER. • Heat transfer coefficient with CAPER is 27.9% higher than without CAPER. • 99.97% salts, 98% metals, >83% aromatic compounds removed from 134 g L−1 TDS PW. [ABSTRACT FROM AUTHOR]

• Energy simulation of AIS using experimentally validated thermal resistances. • AIS evaluation at varying orientations, climate zones, and switching ratios. • Investigation of AIS switching and wall thermal conductivity/heat transfer. • Application of freeze timer to reduce the number of switches of AIS. Active insulation systems (AISs) in buildings are envelopes that integrate thermal insulation, thermal energy storage, and controls. Although different designs for AISs have been proposed in the literature, a comprehensive analysis of feasible AISs is lacking. This paper discusses the energy performance, peak demand reduction potential, and performance characteristics of an AIS that uses a concrete wall as thermal mass sandwiched between two solid-state thermal switches (STSs). These STSs change their thermal conductivity using an on/off metal switch to create or break a thermal bridge across the STS. This paper first describes the experimental setup, used to determine the ratio of thermal resistance during R-high (low thermal conductivity) and R-low (high thermal conductivity) states of the STSs. This ratio was then used in whole-building energy simulations to evaluate the performance of AIS walls across different climate zones with/without a freeze timer of 60 min. The timer was added to reduce the number of switches of STSs from one state to another, and hence the energy needed for these switches. Analysis of the switching frequency and interval of STSs, thermal conductivity of walls, impact of wall orientation, and heat transfer through the wall from the use of AIS at different climate zones/locations were performed. The simulation results show that the AIS can achieve energy savings ranging from ∼ 980 to 2,290 kWh in a single-family home with a floor area of ∼ 220 m2 compared with an IECC 2018 baseline. The energy savings was higher in dry climate zones which represent 17% of residential buildings in the United States, compared to humid or marine climate. [ABSTRACT FROM AUTHOR]

Abstract: Several advanced He-cooled W-alloy divertor concepts have been considered recently for power plant applications. They range in scale from a plate configuration with characteristic dimension of the order of 1m, to the ARIES-CS T-tube configuration with characteristic dimension of the order of 10cm, to the EU FZK finger concept with characteristic dimension of the order of 1.5cm. The trend in moving to smaller-scale units is aimed at minimizing the thermal stress under a given heat load; however, this is done at the expense of increasing the number of units, with a corresponding impact on the reliability of the system. The possibility of optimizing the design by combining different configurations in an integrated design, based on the anticipated divertor heat flux profile, also has been proposed. Several heat transfer enhancement schemes have been considered in these designs, including slot jet, multi-hole jet, porous media and pin arrays. This paper summarizes recent US efforts in this area, including optimization and assessment of the different concepts under power plant conditions. Analytical and experimental studies of the concepts and cooling schemes are presented. Key issues are identified and discussed to help guide future R&D, including fabrication, joining, material behavior under the fusion environment and impact of design choice on reliability. [Copyright &y& Elsevier]