Search

• Anodic oxidation coating's cracking causes a severe substrate stress concentration. • Sealing weakens anodic oxidation coating's cracking resistance during fatigue tests. • Prior shot peening enhances the fatigue property of anodic oxidation coated specimen. In this study, the effects of sealing and prior shot peening treatments on the fatigue behavior of the sulphuric acid anodic oxidation coated 6082-T6 aluminium alloy were investigated. Experimental results indicate that the preferential fracture of anodic oxidation coatings due to its higher brittleness and lower fracture toughness as well as the stress concentration of near-interface substrate caused by the interface cyclic dislocation accumulation could cause the fatigue failure of anodic oxidation coated specimens. Consequently, the fatigue property of anodic oxidation coated specimens notably decreases compared to as-machined specimens, with a decrease of 26.7 % in the fatigue limit corresponding to 2 × 107 fatigue cycles. Additionally, the sealing treatment introduces numerous cracks that penetrate the coating entirely, diminishing the coating's resistance to cracking under fatigue loading; this alteration changes the fatigue failure mechanism of anodic oxidation coated specimens, ultimately resulting in a decrease of 15.5 % in the fatigue limit of anodic oxidation coated specimens. Despite exacerbating the surface integrity and increasing the surface roughness of anodic oxidation coated specimens, the prior shot peening treatment increases the fatigue limit of anodic oxidation coated specimens by 82.8 % since the affecting layer beneath the interface plays a crucial role in inhibiting the further propagation of coating cracks into the substrate as well as the crack propagation in the substrate beneath the interface. [ABSTRACT FROM AUTHOR]

• The UPM and PI iterative methods can accurately reconstruct the residual stress field induced by rolling processing. • The extended finite element method and the weight function method are applied to solve the stress intensity factor. • The necessity of deep rolling treatment for axles is verified. • The influence of interference and initial crack position on the remaining life of axle is explored. • The damage tolerance analysis of the axle was carried out. Deep rolling surface strengthening is an effective way to introduce compressive residual stress (CRS) along the railway axle, which can improve the fatigue resistance of the material. The CRS field was rebuilt adopting the proportional-integral (PI) iteration method and the unit pressure method (UPM) to study the fatigue cracking behavior of deep-rolled EA4T railway axles. The remaining life prediction model and the stress intensity factor (SIF) solution method were then validated using simulations and testing with small-sized specimens. The remaining life of the EA4T railway axle was then calculated by applying a realistic vertical load spectrum. The results showed that CRS prevented crack propagation, enhanced the critical propagation size of railway axle cracks, and prolonged the remaining life of the axle. Additionally, the remaining life of the axle may not support the following maintenance period if a crack with an extendable size emerges at the unloading groove of the railway axle. This work provides a theoretical basis for the optimization of the non-destructive testing (NDT) interval of deep-rolled EA4T railway axles. [ABSTRACT FROM AUTHOR]

• Prior shot peening improves the CF limit of AO coated aluminum alloy by 50 %. • AO specimens exhibit different CF failure modes under low and high applied stress. • Substrate residual stress and microstructure affect the CF crack propagating path. • Substrate residual stress relaxes in distinct mode under low and high applied stress. Plain (anodic oxidation) and composite (prior shot peening + anodic oxidation) coatings were prepared to investigate their effects on the corrosion-fatigue (CF) property of 6082-T6 aluminium alloy in a 3.5 wt% NaCl aqueous solution. The results indicate that plain coated specimens exhibited similar CF properties to as-machined specimens at low applied stresses. However, under high applied stresses, the plain coating led to a preferential fracture and was unable to effectively prevent corrosion medium. Hence, the CF property of plain coated specimens was found to be inferior to as-machined specimens at high applied stresses. The synergetic effect of substrate residual stress and microstructure beneath the coating-substrate interface reduced the crack propagating rate in the initial stage by deflecting the crack at the grain boundary. Therefore, the CF property of composite coated specimens improved as a whole when compared with as-machined and plain coated specimens. Besides, under low applied stresses, the near-interface substrate residual stress of composite coated specimens occurred the relaxation due to the substrate crack propagation, while under high applied stresses, this was due to the synergetic effect of materials' local cyclic yield and plastic flow, as well as the substrate crack propagation. [ABSTRACT FROM AUTHOR]

Abstract In this study, the precipitate strengthened Cu-Ni-Si alloy was micro-shot peened by ceramic balls with a diameter of 40 μm. The fatigue tests using the peened specimens were conducted in air and in salt atmosphere respectively. The results show that a fine and hardening layer is formed on the surface of peened specimen and the compressive residual stress is introduced. There is no fatigue limit for specimens in both test conditions. The S-N curve of specimens in salt atmosphere shows a continuous decrease with the increasing number of loading cycles, while that in air shows a step-wise shape. Compared with the un-peened specimens, the fatigue strengths of specimens at 107 cycles are increased by 47% and 67% in air and in salt atmosphere respectively. The peened specimens in air condition failed from subsurface zone in high cycle fatigue region, while all the other specimens failed from surface. The micro-shot peening can improve the surface property and delay the crack initiation and propagation, so as to enhance the fatigue strength greatly. Highlights • The fatigue failure changes from surface to subsurface by micro-shot peening. • Micro-shot peening can delay both the crack initiation and early propagation. • The micro-shot peening can further improve the fatigue strength in salt atmosphere. [ABSTRACT FROM AUTHOR]

Abstract Tb3+-doped CaAl LDH with fluorescent property has been prepared in ethanol/water media. After it is exposed to 0.01, 0.05, 0.10, and 0.25 mol L−1 cytosine solution, respectively, the amount of the cytosine present in the Tb3+-doped CaAl-LDH/Cyt-n composites is separately about 0.01, 0.01, 0.03, and 0.05 mol per 1 mol Tb3+-doped CaAl-LDH by compositional analysis. XRD patterns reveal some reflections attributed to cytosine in some composites. IR spectra show that bands attributed to cytosine appear in some composites. Fluorescent spectra suggest that the intensity of the emission due to 5D 4 —7F 5 transition of Tb3+ gradually increases with increasing amount of the cytosine present in the Tb3+-doped CaAl-LDH. The mechanism of fluorescence enhancement based on the intermolecular energy transfer from cytosine to Tb (III) has been proposed and discussed. Graphical abstract The effect of cytosine on the fluorescence of Tb3+-doped CaAl LDH has been studied. The emission attributed to 5D 4 →7F 5 transition of Tb3+ doped in CaAl-LDH gradually became stronger with increasing amount of cytosine incorporated in the Tb3+-doped CaAl-LDH. Meanwhile, the lifetime of the emission ascribed to 5D 4 →7F 5 transition of Tb3+ gradually decreases with the increase in the amount of cytosine present in the Tb3+-doped CaAl-LDH. The mechanism of fluorescence enhancement based on the intermolecular energy transfer from cytosine to Tb3+ in the Tb3+-doped CaAl-LDH/Cyt. composites has been proposed. fx1 [ABSTRACT FROM AUTHOR]

• The surface properties of EA4T axle steel treated by ultrasonic surface rolling process (USRP) are investigated. • Effect of USRP on the electrochemical corrosion resistance and corrosion fatigue performance is elucidated. • Residual stress relaxation mechanism of USRP-treated EA4T axle steel in air and corrosion is revealed. • Influence of residual stress relaxation on the corrosion fatigue resistance is clarified. The fatigue properties and residual stress relaxation behavior of EA4T axle steel treated by ultrasonic surface rolling process (USRP) are investigated in air and corrosive environments. The result reveals that the surface roughness (Ra) is decreased from 1.42 to 0.17 μm after the USRP. A surface layer with ultrafine grains, work hardening, and compressive residual stress (CRS) is achieved by the USRP. Compared with the as-machined specimens, the USRP specimens exhibit slightly lower electrochemical corrosion resistance but superior fatigue performance in air and corrosive environments. The dislocation density is significantly decreased in the corrosive environment during fatigue loads, accompanied by a rapid relaxation of surface CRS. The influence of USRP on the corrosion fatigue performance is elucidated. The residual stress relaxation mechanism and its influence on fatigue resistance are also analyzed. [ABSTRACT FROM AUTHOR]

This work reports micro-defects and growth mechanism of the plasma electrolytic oxidation (PEO) coating formed on the surface of 6082-T6 aluminum alloy. Scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray computed tomography techniques were used to characterize the morphology, phase, microstructure, and porosity of the PEO coating, respectively. The results confirmed a porous outer layer and a dense inner layer in the coating. The PEO coating was composed of γ- and α-Al 2 O 3 phases, and amorphous phases. A layer with only amorphous structures was found near the coating/substrate (C/S) interface, which could be ascribed to the high concentration of P element in the electrolyte. Micro-defects with different sizes and shapes inside the coating were successfully characterized by the high-resolution X-ray computed tomography technique, and the volume reconstruction result revealed a porosity fraction of 5.43% for the coating. A growth model was complemented to explain the growth mechanism and interconnected micro-defects of the PEO coating. • Micro-defects in the plasma electrolytic oxidation (PEO) coating formed on 6082-T6 alloy were firstly characterized by high-resolution X-ray computed tomography technique. • Formation of the amorphous structure at the coating/substrate (C/S) interface was highly dependent on P element in the electrolyte. • Growth mechanism of the coating was clarified based on the microstructural observation and micro-defect characterization. [ABSTRACT FROM AUTHOR]

Low, medium and high-intensity (0.19, 0.26 and 0.34 mmA) shot peening treatments and 0.34 mmA high-intensity shot peening combined with slight and severe polishing treatments were used as the pre-treatments to improve the fatigue property of micro-arc oxidation (MAO) coated 6082-T6 aluminum alloy, respectively. In consideration of the significance of substrate residual stress beneath the coating-substrate interface on MAO coated specimens' fatigue property, the substrate residual stress of various coated specimens was analyzed by the X-ray's powerful penetrability. Results indicate that the substrate residual stress state of MAO coated specimens is changed from tensile (+93 MPa) to compressive (−65 to −93 MPa) by the above pre-treatments, which is beneficial for inhibiting the crack initiation at the substrate or resisting the crack's further propagation from the coating into the substrate. Whereas, similar to the compressive residual stress induced by shot peening, the compressive substrate residual stress for prior shot peening + MAO composite coated specimens will also relax during the fatigue tests. In addition, the gradient compressive residual stress beneath the interface induced by prior shot peening reduce the crack propagating rate, thus improving the fatigue property of coated specimens; after the 0.26 mmA shot peening pre-treatment, the fatigue strength at 2 × 107 cycles of MAO coated specimens increases by 59.1 %. Finally, the effects of surface and interface roughness, substrate residual stress and in-depth compressive residual stress on the fatigue life of MAO coated specimens are further discussed. • Pre-treatments improve MAO coated Al alloys' fatigue life by 2.41 to 4.35 times. • Grain refinement of substrate increases MAO coatings' pore size and thickness. • Compressive substrate residual stress inhibits crack propagation beneath interface. • Compressive substrate residual stress relaxes by 8 % to 41 % at 104 fatigue cycles. [ABSTRACT FROM AUTHOR]

• CSP and MSP are used to improve the fatigue property of bare and MAO coated Al. • CSP and MSP introduce a grain-refined and CRS affected layer on surface. • CSP and MSP is more appropriate for MAO coated and bare Al, respectively. • Crack initiation stage dominates the fatigue property of bare Al. • Crack propagation stage dominates the fatigue property of MAO coated Al. Conventional shot peening (CSP) and micro-shot peening (MSP) are used to enhance the fatigue property of bare and micro-arc oxidation (MAO) coated 6082-T6 aluminum. The difference in the anti-fatigue strengthening mechanism of CSP and MSP on bare and MAO coated 6082-T6 aluminum alloy is revealed. Results show that MSP provides a more significant improvement in fatigue properties of bare specimens than CSP since the intensely inhibiting effect on crack initiation. Nevertheless, MAO coating impairs the surface integrity of MSP specimens, thus reducing the crack initiating life. In comparison, the effect of deeper affected layer induced by CSP on the improvement of crack propagating life is mostly retained after the MAO process. Hence, for the MAO coated specimen, the CSP prior-treatment is more effective in improving its fatigue property. [ABSTRACT FROM AUTHOR]

• Fatigue life prediction method of 25CrMo4 steel is investigated using fracture mechanics and machine learning methods. • Residual stress relaxation process is incorporated into fatigue crack growth in combination with NASGRO equation and equivalent initial flaw size (EIFS) methodology. • Different machine learning methods areemployed to investigate theireffectiveness in fatigue life prediction. In this work, fracture mechanics and machine learning methods are separately employed to predict the high cycle fatigue (HCF) life of micro-shot peened 25CrMo4 alloy steel containing artificial notches. The influences of notch size, stress level, and surface condition on fatigue life are incorporated into the prediction model. The results shows that the fatigue life of shot-peened specimens is enhanced by the compressive residual stress (CRS) compared with that of the un-peened specimens. The prediction result using fracture mechanics method is within the error band of ±2, while that using machine learning method almost lies in the error band of ±1.5. The stress level and notch size are the most critical factors affecting the HCF fatigue life. The applicability and limitation of the two methods are finally discussed. [ABSTRACT FROM AUTHOR]

Carburized and quenched specimens of 17CrNiMo6 gear steel were given two different shot peening treatments. Post-treatment Vickers hardness, residual stress, roughness and topography were determined. Traditional shot peening can increase surface hardness, residual stress and roughness. By contrast, micro-shot peening can decrease of surface roughness and increase both the surface hardness and residual stress even more. Scuffing tests were carried out using a ring-in-V-notch test configuration. It was found that shot peening can improve the scuffing resistance properties of gear steel, and that a combination of traditional shot peening and micro-shot peening can improve the scuffing resistance of carburized and quenched gear steel to the largest degree. The hardness and residual compress stress, roughness and topography produced during shot peening have an effect on the scuffing resistance of the carburized and quenched gear steel. [ABSTRACT FROM AUTHOR]

The effects of micro-shot peening (MSP) and artificial surface defects were investigated in relation to the defect tolerance of Al-Si-0.6Mg alloy in the framework of fracture mechanics. The results indicated that coral-shaped casting defects inside the alloy could be effectively quantified using the X-ray synchrotron radiation technique. An affected layer with a surface roughness (Ra) of 1.25 and residual stress of − 125 MPa was introduced on the MSP specimen compared to the un-peened (UP) specimen. The fatigue strengths of the UP and MSP specimens containing the artificial defects decreased as the defect size increased under rotating bending fatigue tests, except in the case of defects with the equivalent size of 395 and 490 µm, respectively. MSP could shift the crack initiation site toward the subsurface, while all the cracks of the specimens with the artificial defects originated from the surface and maintained an aspect ratio of 0.66 during the crack growth process. The relationship between the defect sizes and the fatigue strengths could be reasonably assessed by the modified Kitagawa-Takahashi (K-T) diagrams. The critical defect size of the MSP specimens was increased from 450 to 542 µm compared with that of the UP specimens, owing to the beneficial effect of the compressive residual stress. The defect tolerance of the Al-Si-0.6Mg alloy was improved by the MSP process. • Effects of micro-shot peening (MSP) on the fatigue properties of Al-Si-0.6Mg alloy are explored. • Casting defect inside the alloy was identified using synchrotron radiation X-ray computed microtomography (SR-μCT) technique. • The influence of MSP on the fatigue tolerance was characterized by Kitagawa-Takahashi (K-T) diagrams. • The critical defect size harmless to fatigue strength was evaluated using fracture mechanics. [ABSTRACT FROM AUTHOR]

• Effects of the corrosive environment on the fatigue strength of EA4T axle steel are explored. • The evolution of corrosion process during fatigue loading is fully investigated. • Crack aspect ratio in the corrosive environment is obtained by using synchrotron radiation X-ray computed microtomography (SR-μCT). • Fatigue life prediction model is developed based on the pit growth, short crack growth, and long crack growth stages. High-speed railway axle is the critical safety component of modern ground vehicles, which experiences extremely complex environments. In this paper, the effect of corrosion on the fatigue behavior of EA4T axle steel was investigated in an artificial rainwater environment. Combining scanning electron microscopy (SEM) and synchrotron radiation X-ray micro computed microtomography (SR-μCT) with theoretical analysis, damage measurement enabled a full evolution characterization of the corrosion process for exploring the corrosion mechanism and its influence on the fatigue life. It is found that the corrosive environment significantly reduced fatigue strength and facilitated multiple crack initiation, while showed relatively little effect on the long fatigue crack growth. The fitness of the 3-P Weibull distribution was slightly higher than that of the Gumbel distribution in terms of crack population. The life prediction model incorporating the pit growth, short crack, and long crack stages showed a good agreement within the 95% and 5% probabilistic S-N curve. [ABSTRACT FROM AUTHOR]

In this study, the very high cycle fatigue tests were conducted on a kind of high-strength austempered ductile iron (ADI) at 90 Hz and 20 kHz. The S – N curves decrease continuously and there is no fatigue limit in the very high cycle fatigue regime. The fatigue strength of the different frequencies essentially corresponds with each other and the specimens show similar fracture behaviors. Meanwhile, on the fracture surfaces of some specimens, the ‘granular-bright-facet’ (GBF) area is observed. The threshold stress intensity factor for internal crack growth is obtained and the fatigue limit is evaluated based on the defect size. [ABSTRACT FROM AUTHOR]

• The extended finite element method is used in the fracture mechanics simulation of EA4T axle steel specimen and full-scale axle. • Numerical model is built considering residual stress and wheelset press-fitting. • The effectiveness of the extended finite element method (XFEM) was verified by comparing the simulation and experimental results. • The measured load spectrum was applied, and the NASGRO equation was used to calculate the residual life of the axle. High-speed railway axles may be damaged during service or maintenance. Therefore, to ensure axle service safety, the residual life of damaged axles is necessary for an accurate assessment. In this study, a small-sized specimen was analyzed and the effectiveness of the extended finite element method (XFEM) was verified by comparing the simulation and test results. Subsequently, the residual life of the EA4T axle with an initial crack was evaluated using the XFEM, which is based on fracture mechanics, and the actual axle service load spectrum. The results show that the critical failure sizes for the residual life of the power axle and non-power axle were 7 and 4 mm, respectively, for a crack located in the middle of the axle body; in contrast, for a crack located in the arc transition of the wheel seat, the critical failure dimensions were 9 and 5 mm, respectively. Based on the NASGRO equation and considering the damage tolerance safety factor, the residual lives of the power axle for the two crack locations were estimated to be 1.3953 × 106 and 9.636 × 105 km, respectively, while those of the non-power axle were 2.095 × 106 and 1.2583 × 106 km, respectively. The results of this study can provide a reference for the axle non-destructive testing (NDT) period. [ABSTRACT FROM AUTHOR]

Abstract: Austempered ductile irons (ADIs) with three strength grades were produced successfully by different two-stage heat treatments. The microstructure and mechanical properties of ADIs such as tensile strength, yield strength, elongation and impact toughness were studied. The results show that the strengths of the three grades ADIs well satisfy the requirement of ASTM standard 897M-06 grade 900/650/09, grade 1050/750/07 and grade 1200/850/04. Meanwhile, the ductile and impact toughness of the ADIs are larger than those required by the ASTM standard. The microstructure has obvious influence on mechanical properties and fracture behavior. With the decrease of austempering temperature, yield strength and tensile strength of the ADIs increase, while both the impact energy and elongation of them decrease. [Copyright &y& Elsevier]

Abstract: In the present investigation, 35CrMo alloy steel was gas oxynitrocarburized at 550°С, 570°С and 610°С for 2h by applying a low-temperature gas multi-elements penetrating system. Microstructure, surface composition, case depth, microhardness, wear and corrosion resistance were analyzed. The compound layer consisting of γ′-Fe4N and ε-Fe3N and oxide layer of Fe3O4 and Fe2O3 were formed on the ground reference surface after treated. Compared with the conventional gas nitrocarburizing, a larger effective case depth was obtained successfully in a short time after treatment. The microhardness and the properties of wear and corrosion resistance were improved obviously and the properties of samples treated at 570°C are optimum when compared with the samples treated at 550°С and 610°С for the same duration. [Copyright &y& Elsevier]

• A new type of CFRP Bars reinforced Coral Concrete was developed; • Test was performed, the mechanical property of this type of structure was studied; • Crack development process for this type of new structure is discovered. • A new formula to predict the crack width of this new type structure is developed. In order to study the crack development of CFRP reinforced coral concrete under different bending conditions, experimental study investigation of crack width of steel and CFRP reinforced coral concrete beams were performed. A comparative study of cracking rate, maximum crack height and crack patterns in CFRP bars reinforced coral concrete beams at different stages is made with ordinary steel reinforced coral concrete beams. The results show that under similar reinforcement ratio, the crack width and crack spacing of CFRP reinforced coral concrete beams are larger than that of steel reinforced concrete beams, increasing the reinforcement ratio of test beams can effectively reduce the crack width. The current deign formula from existing design codes overestimates the value of the relative bond characteristic coefficient (v i) and the strain inhomogeneity coefficient (ψ). Therefore, in this paper, the formula for maximum crack width of CFRP bars reinforced beams is developed based on the experimental data, the relative bond characteristic coefficient, the strain inhomogeneity coefficient of the longitudinal reinforcement, the ratio of the maximum crack width to the average crack width (τ s) are included in the formula. The formula is validated with test results, the calculated value agrees well with the experimental results. Therefore, can be used for the future design. [ABSTRACT FROM AUTHOR]

In this study, the effects of micro-shot peening and artificial defect on the fatigue properties of EA4T railway axle steel were evaluated. Un-peened (UP) and micro-shot peened (MSP) EA4T axle steel specimens were drilled to introduce artificial defects on the surface. Then the fatigue tests were conducted on a rotary bending fatigue machine (R = −1). The test results showed that the fatigue limit of the UP specimens was improved by 25% after MSP; when the equivalent defect sizes were less than 60 and 70 μm respectively, they had no negative effect on the fatigue strength of the UP and MSP drilled specimens, otherwise the fatigue strength of both specimens decreased with the increase of the defect size. The fracture surfaces were analyzed by scanning electron microscopy (SEM) observations, which indicated that crack initiation sites for the as-prepared UP and MSP specimens were on the surface, while for the drilled specimens, they were on the vicinity of hole defects. The effect of artificial defect size on the fatigue strength of the UP and MSP specimens and the critical defect size were analyzed with fracture mechanics approach, the results of which showed that the relationship between defect size and fatigue strength of the UP and MSP specimens can be well evaluated by the modified Haddad model, and the critical defect size of the UP specimens was 65 μm while that of the MSP specimens was increased to 76 μm due to the introduction of compressive residual stress. [ABSTRACT FROM AUTHOR]

In this study, EA4T axle steel specimens were subjected to three shot peening treatments: conventional shot peening (CSP), micro-shot peening (MSP) and their combination, i.e. dual shot peening (DSP). The residual stress, surface roughness, morphology, microhardness, were used to characterize the affected surface layer. The results indicated that MSP achieved maximum surface compressive residual stress (SCRS), minimum surface roughness, high surface microhardness. Moreover, compared to CSP, DSP improved the SCRS and microhardness while reducing surface roughness. However, scanning electron microscopy (SEM) observations indicated the presence of intensive defects of the DSP-treated specimens, which hindered the fatigue strength of the specimens. Fatigue tests were conducted to evaluate the effect of different treatments on fatigue life, the median S - N curve demonstrated that the fatigue limit at 107 cycles was improved by 24, 32, and 27% for the CSP, MSP, and DSP specimens, respectively. Furthermore, SEM observation was conducted to analyze the fracture mechanisms, the results indicated that the failure of all specimens originated at the surface and the fracture mechanisms were not changed by the shot peening treatments. The SCRS during the cyclic loading have also been analyzed. Moreover, the factors influencing fatigue limit improvement were discussed. [ABSTRACT FROM AUTHOR]

• Cause and consequence analysis for industrial hot work is conducted. • The ABT model and PN are integrated to analyze hot work accident evolution. • An improved regional center method is developed to obtain crisp evaluation value. • Data fitting is performed for probability calculation. Hot work poses great hazards to industrial operation site. Although regulatory and guidance exist, accidents caused by hot work continue to occur. Risk assessment has proved to be an effective method for risk control. However, current studies paid less attention to the evolution process of industrial hot work accidents and the quantitative risk assessment seems to be insufficient. In this context, we aimed to perform comprehensive risk evolution analysis and quantitative risk assessment of hot work using adaptive bow tie (ABT) and Petri nets (PNs). The ABT model is improved to analyze deep causes, consequences, and their relationships. PNs are employed to conduct quantitative risk assessment. To address uncertainties, the triangular membership function and improved regional center method are proposed to calculate the confidences of all places and transitions in the PNs. The probabilities are finally obtained by data fitting method. The study found that the most likely consequence of hot work accident is near miss. The results also indicate that hot work accident prevention measures should emphasize on the isolation of workplace, combustible gases test, removal of combustible substances, job organization, and job training. Besides, emergency devices maintenance and emergency drilling are critical to prevent accidents from expanding. [Display omitted] [ABSTRACT FROM AUTHOR]

It's well known that the development and distribution of roots could be regulated to obtain deep soil resource and enhance the grain yield by increasing the depth of fertilization, but little is known about whether increasing P fertilization depth can optimize the root distribution to delay leaf senescence, enhance photosynthetic performance and root-shoot coordination or not. We conducted a field experiment that tested the following four placement depths of P fertilization: 5 cm (P 5), 10 cm (P 10), 15 cm (P 15), and 20 cm (P 20). The experiment was designed to explore the regulatory effects of the P fertilization depth on the root growth and distribution, the photosynthetic performance, the root-shoot coordination, the yield formation, the N and P fertilizer utilization of maize plants. We found that deep P placement did indeed alter the root parameters. In the 20–60 cm soil layer, both the root dry weight and length of P 15 treatment were on average 23.2% higher than those of P 5 treatment. The specific root length and specific root surface area of P 15 treatment were 4.5% and 5.6% higher than those of P 5 treatment. In addition, the P 15 treatment achieved a significantly improved photosynthetic performance over the P 5 treatment: The leaf area index at the R6 stage was 10.2% higher, the leaf senescence index from the R2 to the R6 stages was 31.4% lower, the photosynthetic rate at the R3 stage was 25.9% higher. The P placement depth also optimized the root-shoot coordination: The ratios of root weight to shoot weight, root surface area to leaf area, and root length to leaf area of P 15 treatment were 6.7%, 13.8%, and 12.7% higher than those of P 5 treatment, respectively. Finally, the root P and N uptake efficiency, the photosynthetic P-use efficiency, and the physiological P-use efficiency of P 15 treatment were all significantly higher than those of P 5 treatments. And together these responses had the effect of increasing the mature biomass by 12.5%, and the grain yield by 22.0%. In conclusion, increasing the P fertilization placement depth to 15 cm regulates the growth and development of the root system, which in turn improves the capability of plant to uptake and utilize N and P in the soil, delays the onset of leaf senescence, enhances its photosynthetic performance and biomass accumulation rate, and thus ultimately increases the yield. [Display omitted] • Deep P fertilization optimizes root growth, and root-shoot coordination. • Deep P fertilization delays leaf senescence and improves photosynthetic performance. • Optimized root-shoot coordination improves the grain yield and nutrient use efficiency. [ABSTRACT FROM AUTHOR]

Highlights • Effect of a shear-affected-zone (SAZ) on fatigue limit was investigated. • Tests on specimens with and without SAZ were conducted. • Propagation resistance of the fatigue crack has been lost by the punching process. • Fatigue crack growth mode had a possibility of transition from Mode I to Mode II. • Fatigue limit design for the punching processed plate was coarse-grained. Abstract It is well known that the fatigue limits of some precipitation-hardened steels with a punched hole do not increase, even if the tensile strengths of base-metal increases. This study suggested that the dominant reason for this strange phenomenon is a transition from the Mode I type fatigue crack propagation due to the cyclic plastic deformation to Mode II type propagation due to the damage accumulation by a quantitative analysis of influential factors based on fracture mechanics. This result can open a probability that the fatigue limit of the punched hole with shear-affected zone can be actively quantified. [ABSTRACT FROM AUTHOR]

Cytokinin is known to be involved in the regulation of plant responses to counteract the adverse effects of stress conditions. This work investigated the effects of exogenous spraying of 6-benzyladenine (6-BA) after water logging for 6 days at the third leaf stage (V-3WL + BA) and the sixth leaf stage (V-6WL + BA) on grain yield and growth of summer maize hybrids DengHai605 (DH605) and ZhengDan958 (ZD958), which are planted most popularly in China. Waterlogging under field conditions delayed the growth process, decreased leaf area index, chlorophyll content and dry matter accumulation, resulted in a significant reduction of grain yield with a decrease of 30.30% and 18.78% under V-3WL (water logging for 6 days at the third leaf stage) and V-6WL (waterlogging for 6 days at the sixth leaf stage) of DH605, 30.39% and 21.38% under V-3WL and V-6WL of ZD958, respectively, compared to the control (CK). By contrast, exogenous application of 6-BA effectively alleviated the adverse effects of waterlogging on summer maize by delaying leaf senescence, increasing chlorophyll content and improving photosynthetic performance. At tasseling stage, the P n of V-3WL + BA and V-6WL + BA in DH605 increased by 9.57% and 8.38%, respectively, compared to that of V-3WL and V-6WL, while the corresponding values for ZD958 increased by 2.96% and 4.05%, respectively. Those responses are conducive to the accumulation of photosynthetic products, increasing grain filling rate, and improving ear character, and then leading to increase grain yield of summer maize. Grain yield of DH605 under V-3WL + BA and V-6WL + BA increased by 15.57% and 12.39%, respectively, compared to that of V-3WL and V-6WL, while the corresponding values for ZD958 increased by 20.05% and 15.32%, respectively. Clearly, spraying exogenous 6-BA could effectively improve grain-filling characteristics and photosynthesis of waterlogged summer maize, resulting in a significant increase of grain yield, compared to water logging treatments. [ABSTRACT FROM AUTHOR]

• Vanadium addition causes an increase in both yield strength and yield ratio. • Vanadium addition reduces strain hardening ability, and weakens wear resistance. • RCF crack initiation of V-alloyed stee is delayed by increasing yield strength. • RCF crack growth size is restricted by reducing plastic deformation capacity. • Increasing yield ratio improves RCF resistance, but weakens wear resistance. This study aims to evaluate the effect of vanadium microalloying on rolling contact fatigue (RCF) and wear behavior of railway wheel steels. It involves microstructural analysis and mechanical testing, including hardness, tensile, and rolling/sliding tests on the test steels, followed by electron backscatter diffraction, residual stress, and microhardness analyses after rolling/sliding tests. The findings demonstrate that vanadium microalloying leads to the alleviation of dynamic recrystallization, strain hardening, and compressive residual stress within the outermost layer beneath the worn surface, indicating a reduction in the plastic deformation capacity during dry rolling/sliding conditions. RCF resistance of railway steel can be enhanced through vanadium microalloying, as it simultaneously delays crack initiation by increasing yield strength and restricts crack growth by reducing plastic deformation capacity. While vanadium microalloying enhances the matrix hardness of wheel steel, it concurrently diminishes its strain hardening ability, potentially compromising its wear resistance. In addition, this study found that the yield ratio, being indicative of plastic deformation capacity and strain hardening ability, can serve as a suitable parameter for characterizing the RCF and wear resistances of tested steels. It exhibits a positive correlation with RCF resistance and a negative correlation with wear resistance. [ABSTRACT FROM AUTHOR]

Leaf senescence is associated with fundamental changes on the level of the proteome and it can be modulated by nitrogen. To determine the precise regulatory mechanisms underlying these effects, we conducted a comparative proteomics study using 2-dimensional gel electrophoresis and MALDI-TOF/TOF MS. Based on our study of the maize leaf proteome, leaf senescence induces complex responses including the degradation of 32 senescence-associated proteins that are involved in many biological processes, especially energy, metabolism and cell rescue, defense and virulence pathways. Although similar conclusions have been highlighted in other crops, this study filled the knowledge gap in maize leaf senescence. Moreover, we discovered, for the first time, 29 “nitrogen-regulated senescence proteins” had significant ( P ≤ 0.05) interaction term for nitrogen × stage. Although further study of nitrogen-related senescence proteins, such as 30S ribosomal protein, will be required to fully elucidate their complex functions, the surprising results in our study provide a new vision to research the relationship between nitrogen and senescence. [ABSTRACT FROM AUTHOR]

• The overset mesh technology is used to simulate the train running in the tube. • The flow topology considering the ground effect has been visualized numerically. • The influence of the nose length on the wave systems is reported. • Two distinct mechanisms for the formation of flow separation are identified. • The relationship between the aerodynamic loads and flow structures is described. The flow structure and aerodynamic loads in evacuated tube transportation with three nose lengths (5, 10 and 15 m) at 1500 km/h are investigated by overset mesh technology. The governing equations of the IDDES model for 3-D, unsteady compressible flow are employed. The numerical algorithm is validated via moving model and wind tunnel experimental data. The flow topology considering the ground effect is revealed and compared. The wake is highly complex, characterized mainly by wave systems and trailing vortices. Additionally, the influence of the nose length on the generation of wave systems is discussed in detail. The largest shock intensity is identified at 5 m case, followed by 15 m case, and the smallest case at 10 m. Differences in wave systems also caused the two distinct mechanisms for the formation of flow separation and the evolution pattern of the wake vortex to be identified for three nose configurations. By comparison, the nose length increase is helpful to reduce the length of the disturbed region of the leading shock wave, the aerodynamic loads on the train surface and aerodynamic drag. A qualitative description is also presented of the relationship between the fluctuations of aerodynamic loads and flow structures. [ABSTRACT FROM AUTHOR]

With the extensive promotion of controlled-release urea (CRU), its N-release pattern has been shown to match the crop's N-demand period and improve crop yield by reducing N losses. Nevertheless, the impacts of CRU on summer maize yield, especially on greenhouse gas emissions, have rarely been reported during its long-term use. It is necessary through long-term positioning field experiment with CRU application to investigate the regulatory mechanisms of maize yield formation, nitrogen use efficiency (NUE), ammonia volatilization and greenhouse gas emissions. The long-term fertilizer positioning experiment for ten years, four treatments were performed: polymeric-coated controlled-release urea (CRF, 42% N, 3-months controlled-release period), sulfur-coated controlled-release urea (SCF, 35% N, 3-months controlled-release period), common urea (CCF, 46% N) and no nitrogen fertilizer (CK). Results showed that the two coated controlled-release fertilizers significantly increased NUE and dry matter accumulation in summer maize, and ultimately improved grain yield. Compared to CCF, CRF and SCF treatments increased post-silking dry matter accumulation by 16.3% and 13.3%; NUE by 42.3% and 28.9%. The 2-year mean grain yield of CRF and SCF treatment increased 9.0% and 12.4% compared to CCF treatment. CRF treatment significantly increased the NO 3 --N content in 0–60 cm soil layer; while CRF and SCF treatments showed a significantly higher NH 4 +-N concentration in the 0–20 cm soil layer than CCF treatment. Compared to CCF treatment, the CRF and SCF treatments significantly reduced peak ammonia volatilization, and the average cumulative emissions of ammonia volatilization of two years were reduced by 80.8% and 53.2%, respectively. CRF treatment had lower peak of N 2 O emissions but longer N 2 O emission duration than other N application treatments. The two-year average cumulative N 2 O emissions from CRF treatment increased by 49.6%, and SCF treatment increased by 61.1% compared to CCF treatment. Compared to CK treatment, total cumulative CH 4 uptake was 36.1% lower in CRF treatment, 60.9% in SCF and 78.9% in CCF treatment. The higher cumulative N 2 O emissions from CRF and SCF treatment resulted in a significantly higher global warming potential (GWP) than CCF treatment. The two-year mean increase in greenhouse gas intensity (GHGI) was 36.2% for CRF treatment and 44.7% for SCF treatment compared to CCF treatment. Long-term application of coated controlled-release fertilizers could achieve high yields and nitrogen use efficiency. However, there is a risk of increased N 2 O emissions, causing elevated GHGI. In the future, it is necessary to strengthen the research on the comprehensive effects of long-term reduced application of CRU on crop yield and greenhouse gas emissions, in order to promote the wide application of environmentally friendly CRU in the field. [Display omitted] • Long-term application of CRU could achieve sustainable crop yield improvement. • Long-term application of CRU significantly reduced ammonia volatilization and CH 4 emissions. • Long-term application of CRU carried the risk of increased N 2 O emissions, leading to higher GHGI. [ABSTRACT FROM AUTHOR]

• The preferentially dissolved ferrite in pearlite and shedding of cementite lamellae contribute to the formation of corrosion pits. • Corrosion fatigue crack initiation and growth mechanism of U75V rail steel is clarified. • Corrosion fatigue crack initiation behavior is related to morphology ratio and local shape of corrosion pits. Understanding the corrosion fatigue mechanism of rail materials is of great importance to guide the assessment of the structural integrity of modern railway components. To this purpose, the corrosion fatigue crack (CFC) initiation and growth behaviors of heat-treated U75V rail steel are investigated under 3.5 wt% NaCl solution in terms of high-cycle fatigue, fatigue crack growth (FCG) rate, together with surface morphology and microstructure. Experimental results reveal that the U75V rail steel is susceptible to corrosion fatigue failure. Examinations on fractured samples clearly show that the electric potential difference between ferrite and cementite triggers the preferential anodic dissolution of ferrite, leading to corrosion fatigue crack initiation. The crack initiation is not only solely determined by the size of the corrosion pit, but also strongly influenced by its local shape. In comparison with the fatigue crack growth in air, the corrosion FCG tends to grow in a relatively straight path, because of hydrogen embrittlement. Additionally, the CFC behaviors indicate a tendency to transverse through soft-oriented grains and deflect upon encountering hard-oriented grains. [ABSTRACT FROM AUTHOR]

• Fatigue tests are conducted for small specimen and press-fitted axle with defect. • Press-fitted axles exhibit notably lower fatigue strength than small specimens. • Goodman relation is used to consider mean tensile stress induced by press-fitting. • The error of predicted notch fatigue strength is controlled to less than 11%. In order to evaluate the notch fatigue strength of transition groove in railway axle, a series of fatigue tests were conducted on small specimens and press-fitted axles containing surface defects. Based on the experimental and finite element (FE) analyses, a novel method considering mean stress effect was proposed to evaluate the fatigue strength of scale railway axle with surface defect. It is found that press-fitted axles exhibit significantly lower notch fatigue strength than small specimens. Furthermore, the theory of critical distance (TCD) provides a good correlation between the notch fatigue strength of small specimens and experimental results. FE analyses revealed that the press-fitting reduces the fatigue strength of the transition groove through increasing stress concentration and introducing a mean tensile stress that decreases with an increase in the applied loading. To account for the mean stress effect, the axial stress at the groove is corrected as an equivalent stress amplitude at R = -1 based on Goodman relation. Through the combination of TCD and Goodman relation, an estimated fatigue strength with an error of less than 11 % can be achieved for the scale railway axle with surface defect. [ABSTRACT FROM AUTHOR]

Global climate change has significantly increased the frequency and intensity of high temperature and drought stresses. Additionally, the high temperature and drought are often concurred, which make the situation of maize production tougher. However, the influence of the combined stresses of high temperature and drought on summer maize production remains uncertain. The study aimed to investigate the effects of high temperature, drought, and their combined stress at different growth stages on photosynthetic and senescence characteristics of summer maize. Denghai 605 (DH605) was used as the experimental material. High temperature (T), drought (D), and their combined stress (T-D) for 6 days were set at the 3rd leaf stage, 12th leaf stage, and tasseling stage, respectively. The natural temperature and normal water management were used as the control (CK). The results showed that high temperature, drought, and their combined stress at different growth stages decreased the activities of antioxidant enzymes and soluble protein content in leaves, leading to increases in MDA content and damage to cell membranes, which accelerated the senescence of the plant. Accordingly, the activities of RuBPcase and PEPCase were decreased, indicating the abilities of plants to harvest and utilize light energy declined due to high temperature, drought, and combined stresses at different growth stages. As a result, the Pn and thus, the dry matter accumulation rate were decreased by these stresses. In addition, the translocation of dry matter to ears was impeded by stresses, especially by the high temperature at the VT stage. While, high temperatures concurred with drought aggravated the adverse effects on summer maize, compared with single stresses. Significantly, high temperature, drought, and their combined stresses at the VT stage decreased the yield mostly, followed by stresses at the V12 stage, and then by stresses at the V3 stage. Compared with CK, the yield of VT-T-D, V12-T-D, and V3-T-D were decreased by 61.6 %, 13.7 %, and 10.4 %, respectively. As global climate change is unstoppable, the superimposed changes of various meteorological factors make the growth conditions for crop production extreme. Studies to explore the combined effects of two or even more meteorological factors on crop growth are becoming more and more important. This study fulfilled the current knowledge gap of the combined stresses on maize production, however, the underlying mechanisms should be dug out in the future. • High temperature, drought and their combined stress at different growth stages accelerated the senescence of the plant. • Drought concurred with high temperature aggravated the adverse effects on summer maize, compared with single stresses. • Drought concurred with high temperature certainly aggravated the increases of VPD, straining the relationship of CO 2 intakes and water losses. [ABSTRACT FROM AUTHOR]

The North China Plain (NCP) is typically cropped using a winter wheat–summer maize double cropping system, which has huge potential for straw production. The region also experiences atmospheric pollution caused by straw burning, which has become an important contributor to global warming. The goals of this experiment were to resolve the conflict between soil fertility and greenhouse gas emission when using straw return to the field and to identify the best balance between environmental protection and agricultural production. A randomized block design with three replicates was used. The design included three treatments based on the return of all winter wheat stalks to the field: (1) all summer maize stalks were pulverized mechanically and returned to the field (SR); (2) half of the summer maize stalks were pulverized mechanically and returned to the field (1/2 SR); and (3) all summer maize stalks were fully removed (control: CK). This long-term test was performed for 6 years. Straw returned to the field significantly increased greenhouse gas emissions. The cumulative CO 2 emissions were higher by 32% under SR and by 17% under 1/2 SR compared with CK. The cumulative N 2 O emissions were higher by 28% under SR and 15% under 1/2 SR compared with CK. The greenhouse gas efflux increased with increased amounts of straw returned to the field. Compared with SR, 1/2 SR significantly reduced greenhouse gas emissions, while still ensuring sustainable soil fertility. Additionally, our research showed that the upper part of the corn stalk is better for generating biomass energy than the lower part. This study provides a theoretical basis for using the upper stalk for bioenergy and the lower stalk for direct return to the field for fertilization. Unlabelled Image [ABSTRACT FROM AUTHOR]

How to improve nitrogen (N) efficiency and reduce environmental pollution caused by N loss has attracted much attention. However, limited research has lacked a comprehensive exploration of the effects of applying UAN under the micro sprinkling fertigation on reactive N (Nr), fertilizer efficiency and net benefits including environmental costs, plus associated responses of the microbial metagenome. The aim of this study was to assess the impact of N management practices on maize yield, Nr losses, and soil microbial community composition and function. Urea and urea ammonium nitrate solution (UAN) were used as N sources, and three N application rates (210, 168 and 0 kg N ha−1) and two fertilization methods (micro sprinkling fertigation and traditional fertilization) were set as the three key components. The results showed that micro sprinkling fertigation treatments reduced Nr losses, increased yield and N efficiency. Compared with urea, the total NH 3 volatilization and N 2 O emissions of UAN under micro sprinkling fertigation were decreased by 14.8% and 30.6%, respectively. Furthermore, the N reduction (FU1) treatment promoted plant N uptake, was saved 20% of N by affecting soil NH 4 +- N and NO 3 --N content, compared to that of urea, and it regulated the microbial abundance of N cycle function related to denitrification and N respiration, reduced global warming potential and greenhouse gas emission intensity. N application method, N source and N rate affected the diversity and composition of soil bacterial community, and altered Nr emissions by changing the abundance of functional microorganisms related to N cycle. Overall, improved N management practice was more conducive to increasing maize yield and net income, saving N resources, and reducing the risk of environmental damage. Our results contribute to a comprehensive understanding of the impact of N management on summer maize production, providing an effective N management practice that is conducive to "green agricultural development". [Display omitted] • A field trial was conducted in Huang-Huai-Hai Plain of China to clarify N losses and net income. • The soil bacterial community was changed by fertilization methods and N sources. • Applying UAN under micro sprinkling fertigation improved maize yield and saved N resources. [ABSTRACT FROM AUTHOR]

Abstract Coccinella septempunctata is a common insect predator that provides biological control of many destructive arthropod pests. An assessment of the toxicity of pesticides to predators is a necessary component of Integrated Pest Management (IPM) strategies. In order to evaluate the risks of field insecticide application, we studied the influence of chlorantraniliprole on C. septempunctata larvae using different exposure doses. Chlorantraniliprole exhibited low contact toxicity against 2nd instar larvae of C. septempuncta ta with the LR 50 was 482.7063 g a.i. ha−1 by after a 72-h exposure. In a long-term test, the LR 50 of chlorantraniliprole for C. septempunctata decreased from 88.97 to 58.22 g a.i. ha−1, while the hazard quotient (HQ) values were below the threshold value of 2 during the entire observation period. This indicated a low toxicity risk from insecticide exposure. The total effect (E) suggested that chlorantraniliprole could be classified as harmless/slightly harmful to C. septempunctata below/at 200% of the MRFR (the manufacturer maximum recommended field rate) of 120 g a.i. ha−1. We also determined no observed effect application rates (NOERs) of chlorantraniliprole on survival (7.5 g a.i. ha−1), developmental time (15 g a.i. ha−1) and fecundity (30 g a.i. ha−1). Chlorantraniliprole significantly reduced the pupation rate, adult emergence, egg hatchability, and predation success. Population parameters, including R 0 , r , λ , and T were significantly affected when C. septempunctata were treated with chlorantraniliprole at higher label rates. These results demonstrated that the use of chlorantraniliprole may reduce C. septempunctata population levels and the level of biological control provided by this species. Graphical abstract Image 1 Highlights • Chlorantraniliprole exhibited relatively low contact toxicity to 2nd instar larvae of Coccinella septempunctata. • Chlorantraniliprole was harmless and/or slightly harmful to C. septempunctata larvae and presented a low toxicity risk. • Chlorantraniliprole significantly affected the survival, development, and predation ability of C. septempunctata. • Chlorantraniliprole strongly affected the fecundity, fertility, and population parameters of C. septempunctata. [ABSTRACT FROM AUTHOR]

Graphical abstract Highlights • Thousand-kernel weight increased with late harvest, increasing grain yield of summer maize. • Late harvest promoted N accumulation after tasseling and N translocation to grain. • N accumulation played a crucial role in the early and middle period, and N translocation did in the mid-late period. Abstract The farmers are accustomed to harvesting summer maize around September 20, but the maize has not yet reached physiological maturity in the Huang-Huai-Hai region, which is adverse for grain yield and mechanized harvest. In order to explore the effect of harvest date on grain yield and nitrogen utilization of summer maize, two treatment in 2016 (CK and 10d) and four treatments in 2017 (CK, 3d, 6d, 10d) were conducted. The sowing dates of all treatments were June 13, and the harvest dates of CK, 3d, 6d and 10d were September 20, 23, 26 and 30, respectively. We found that grain yield and thousand-kernel weight of 10d significantly increased by 17.4–19.8% and 16.8–19.6%, respectively, compared to CK. And partial factor productivity of nitrogen of 10d was 17.4–19.7% higher than that of CK. The grain nitrogen concentration of 3d, 6d and 10d increased by 5.4%, 9.0%, and 9.3–10.8% compared to CK, which promoted nitrogen harvest index, physiological nitrogen use efficiency and partial factor productivity of nitrogen. The reason why nitrogen utilization efficiency increased was that late harvest promoted nitrogen accumulation after tasseling and nitrogen translocation to grain. The nitrogen translocation of 6d was 10.0% in 2017 higher, and that of 10d was 25.1% in 2016 and 15.3% in 2017 higher, respectively, compared to CK. The nitrogen accumulation of 10d increased by 39.0% in 2016, and that of 3d, 6d and 10d increased by 46.5%, 51.3% and 57.3% in 2017, compared to CK. In conclusion, the thousand-kernel weight increased with the delay of harvest date, resulting in increases in grain yield of summer maize. The late harvest promoted nitrogen utilization efficiency resulting from higher nitrogen accumulation after tasseling and higher nitrogen translocation to grain. The contribution of nitrogen translocation to grain yield appeared in the mid-late period (September 23–30), while the contribution of nitrogen accumulation after tasseling did in the early and middle period (September 20–26). Considering annual production of winter wheat-summer maize, the optimized harvest date for summer maize is 6–10 days later than the conventional pattern in this study, that is the cumulative growing degree-days after tasseling reach 613.2–711.5 °C at least. [ABSTRACT FROM AUTHOR]

Graphical abstract Highlights • The cold working causes obvious texture evolution in Cu-Ni-Si alloy. • The cold working has obvious effect on fatigue strength and fatigue fracture mode. • The salt atmosphere changes the fatigue failure from shear mode to tensile mode. Abstract In this study, the tensile and fatigue tests were conducted on precipitate strengthened Cu-Ni-Si alloy. The fatigue properties of specimens with cold working and without cold working in air, as well as that of the specimen with cold working in salt atmosphere were investigated. The results show that the monotonic tensile strength and the yield strength are improved obviously, while the elongation decreases by cold working. The S-N curves of all the types of specimens show a continuous decrease. The fatigue strength of specimens in air is slightly reduced by cold working, however, that of the specimen with cold working at 107 cycles is largely decreased from 190 MPa to 120 MPa in salt atmosphere. All the fatigue cracks initiate from the specimen surface by slip deformation. In air condition, the specimens with cold working show shear mode fracture with transgranular crack propagation and it is caused by the obvious texture, while that without cold working show normal mode fracture with both transgranular and intergranular crack propagation. However, in salt atmosphere condition, the specimens with cold working show normal mode fracture with totally intergranular crack propagation. [ABSTRACT FROM AUTHOR]

Energy analysis of agricultural production is essential to promote sustainable agricultural development. However, the current research on agricultural sustainability in the North China Plain (NCP) mainly focuses on improving grain yield and nitrogen utilization efficiency (NUE), while there are few studies on their energy utilization. This study evaluated the energy utilization characteristics of different yield and NUE category farms and three integrated agronomic approaches in the NCP based on farmer surveys and farm experiments. Compared with the average level of smallholder farms, the net energy (NE) and the energy utilization efficiency (EUE) of high-yield and high-NUE group farms increased by 17% and 22%, respectively, the NE of the high-yield and low-NUE group farms increased by 9%, but the EUE decreased by 12%. The control experiment showed that the NE and EUE achieved using high-yield and high-efficiency agronomic practice (HH) increased by 34% and 18% compared with achieved using traditional farmers' practices, respectively. In conclusion, there is a great opportunity to improve the NE and EUE of the maize production in the NCP by optimizing agronomic practices. Popularizing HH technology by improving agricultural technology extension services is of great significance for improving farmers' EUE and promoting sustainable agricultural development. • Quantitative analysis of the NE and EUE of maize production systems in the NCP. • Improving the EUE for maize production requires an overhaul of management practices. • Adopting HH production practices could simultaneously improve the NE and the EUE. [ABSTRACT FROM AUTHOR]

The application of nitrogenous fertilizer synergist to coordinate nitrogen transformation process in soil may be an efficient strategy to increase nitrogen use efficiency and decrease environmental pollution. However, there are few reports on the application effects of UAN synergistic nitrification and urease inhibitors under the integration of water and fertilizer. This study aimed to explore effects of urea ammonium nitrate solution (UAN) combined with urease and nitrification inhibitors on yield and nitrogen efficiency of summer maize and its ecological effects under the fertigation, and to provide scientific basis for the efficient utilization of UAN. The experimental treatments were as follows: no inhibitor treatment (U), nitrification inhibitor treatment (U-D), urease inhibitor treatment (U-N), and the combination of nitrification and urease inhibitors treatment (U-D+N). Results showed that UAN combined with urease or nitrification inhibitors could significantly reduce the cumulative emission of N 2 O, and then significantly decreased the N 2 O warming potential (GWP N2O) and N 2 O greenhouse gas intensity (GHGI N2O). Compared with U treatment, the cumulative N 2 O emissions of U-D+N, U-N, and U-D treatments was reduced by 45.7 %, 25.3 % and 35.8 %, respectively. The GWP N2O of U-D+N, U-N and U-D treatments decreased by 45.7 %, 25.3 % and 35.7 %, while GHGI N2O decreased by 50.9 %, 30.3 % and 38.9 % on average, respectively, compared to those of U treatment. Application of urease inhibitors significantly reduced NH 3 volatilization. The cumulative NH 3 volatilization of U-N and U-D+N treatments was reduced by 30.7 % and 23.4 %, while U-D treament was significantly increased by 12.3 %, respectively, compared to that of the U treatment. In addition, UAN combined with urease or nitrification inhibitor could significantly increase the contents of NO 3 --N and NH 4 --N in the 0–20 cm soil layer, and significantly reduced the leaching of NO 3 --N to the deep soil. The total nitrogen accumulation, grain nitrogen content, nitrogen transport efficiency and post-anthesis assimilation of summer maize were significantly increased, which were beneficial to the improvement of grain yield and economic benefits. under the fertigation, the synergistic application of UAN with urease and nitrification inhibitors were beneficial to reduce greenhouse gas emissions and ammonia volatilization, improved the nitrogen use efficiency, and then improved the yield and economic benefits of summer maize. Under the fertigation, UAN combined with urease and nitrification inhibitors were beneficial to emission reduction, high yield, and high efficiency. [Display omitted] • The combination of DCD and NBPT reduced N 2 O and NH 3 emission under fertigation. • The combination of UAN with DCD and NBPT improved N use efficiency under fertigation. • The combination of UAN with DCD and NBPT increased maize yield under fertigation. [ABSTRACT FROM AUTHOR]

In order to improve the grain yield of food crops, which is necessary to ensure food security, it is crucial to narrow existing yield gaps. Quantitative analyses of crop yield gaps can provide theoretical support for ascertaining the primary cause of these yield gaps, and then it can be used to increase the grain yield. We evaluated the size and characteristics of the summer maize yield gap in the North China Plain by combining crop models, farmer surveys, and farm experiments. We simulated the summer maize population of farmers' yield level, attainable yield level and potential yield level by establishing three cultivation modes: traditional farming practices (FP), established high-yield and high-efficiency practices (HH) and super-high-yield practices (SH), and introduce the cultivation relying solely on the basic soil fertility (BSF) to reveal the impact of environmental and management factors on yield gap. We explored the driving factors causing observed variations of yield gaps through a quantitative analysis of several additional parameters that are commonly used to characterize the efficiency of the maize production process, including the contribution rates of dry matter and harvest index to grain yield, the radiation interception rate and the radiation conversion efficiency. Our results show that the total yield gap based on farmer surveys and crop models was 4.9 t ha-1, accounting for 37% of the potential yield, of which 46% was exploitable. The total yield gap based on the farm experiments was 3.9 t ha-1, accounting for 30% of the potential yield, of which 69% was exploitable. The grain yield of FP significantly positively correlated with the grain yield of BSF, HH and SH. The contribution rates of dry matter and harvest index to grain yield of FP treatment were 45.7% and 54.3%, respectively. With the increase of yield level, the contribution rate of dry matter increased and the contribution rate of harvest index decreased. In summary, we found a sizeable total yield gap in summer maize in the North China Plain, and a considerable part is exploitable. Optimizing integrated agronomic management has a great potential for closing the exploitable yield gap. Narrowing the yield gap requires a synergistic increase in the contribution rate of dry matter and harvest index to grain yield, but a substantial increase in dry matter is more important. At present, narrowing the exploitable yield gap requires synergistic improvement of radiation interception rate and radiation conversion efficiency to increase the dry matter of maize population. In the future, the regulation measures aiming at narrowing the unexploitable yield gap should further focus on improving the radiation conversion efficiency. • Quantification of the exploitable and unexploitable yield gaps for maize in the NCP. • Dry matter and harvest index contributions to maize grain formation depend on the yield level. • Suggestions for improving the productivity of established maize farming practices. [ABSTRACT FROM AUTHOR]

Crop production alters nitrogen balance in double cropping of winter wheat-summer maize in grain nitrogen content, soil nitrogen pool and nitrogen loss, ultimately affecting nitrogen use efficiency and environmental health. In comparison to the information on crop responses only limited knowledge exists on the response of nitrogen balance to integrated agronomic practices management (IAPM, defined as a comprehensive management framework consisted of tillage method, plant density, seeding and harvest dates, and fertilizer application) under field. Planting pattern will affect crop production and environmental costs. And how the nitrogen balance change under IAPM? In order to answer this question, four treatments (T1, T2, T3 and T4) were conducted on double cropping of winter wheat-summer maize for 4 years in North China Plain. Annual grain yield of T2, T3, and T4 was 22.0%, 51.2%, and 33.3%, respectively, higher than T1. And single grain yield of winter wheat or summer maize had the same trend as the annual grain yield. Dry matter accumulation of T2, T3, and T4 in summer maize season were 8.3%, 42.0%, and 23.0%, and those in winter wheat season were 3.9%, 25.7%, and 12.1%, respectively, higher than T1 at harvest. The grain yield of T4 was lower than that of T3 but higher than that of T1 and T2, and net profit and nitrogen use efficiency of T4 were higher than that of T3. Meanwhile the highest current and residual nitrogen recovery efficiency ( C RE N and RE RE N ) were obtained by T4 treatment during the study period. The soil nitrogen content in 0–90 depth (SN), grain nitrogen content (GN), nitrogen apparent recovery efficiency (ARE N ) and fertilizer nitrogen loss (FNL) were measured for nitrogen balance. T4 treatment promoted nitrogen balance as higher GN, higher ARE N and lower FNL. The GN kept stable and FNL was increasing slowly in all treatments, which mean the contribution to soil nitrogen pool was decreasing with experimental years. The grain yield for T4 treatment of winter wheat, summer maize and annual increased by 36.4%, 31.3% and 33.3% averagely in the past 4 years, compared with T1 treatment. While maintaining crop production, T4 treatment made an important contribution to promoting nitrogen use efficiency, improving the situation of nitrogen balance, and reducing nitrogen loss about 39.1–54.4%, compared with other treatments. [ABSTRACT FROM AUTHOR]

The evolution of surface appearance and the initiation characteristics of fretting fatigue cracks in press-fitted specimens were studied by interrupted rotating–bending fatigue tests. The results show that the distance from each fretting damage zone boundary to the contact edge changes with the number of fatigue cycles, while the wear mechanism remains unchanged. The depth and width of the fretted wear scar near the contact edge increase gradually. Fretting fatigue cracks initiate from the contact area 50–200 μm from the contact edge and appear at approximately 30% of the total fretting fatigue life. Three-dimensional finite element models with the fretted wear scars for interrupted specimens were developed to investigate the effects of fretting wear on surface damage. The models show that the wear scar induced by fretting wear is a source for changes in each fretting damage zone boundary. The stress concentration near the contact edge is reduced and the locations of the maximum values of both the Smith–Watson–Topper (SWT) and Fatemi–Socie (FS) multiaxial fatigue parameters move inward towards the contact zone because of the fretting wear. This causes the crack initiation sites to shift from the contact edge to the inner area; the initiation life increases accordingly. [ABSTRACT FROM AUTHOR]

In the Huang-Huai-Hai region of China, continuous rain is the main meteorological constraint for summer maize, accompanied by stresses of both waterlogging and shading. To evaluate the independent and combined effects of shading and waterlogging on summer maize at different stages, a field experiment was performed to study the grain yield, crop growth, and canopy functionality of summer maize in response to waterlogging (W), shading (S), and their interaction for a 6 day period starting at the third leaf stage (V3), the sixth leaf stage (V6), and the tasseling stage (VT). Shading, waterlogging, and their combination stress (S+W) significantly decreased the grain yield of summer maize. Among these, the simultaneous stress induced greater yield losses than single stresses at any growth stage. The reduction of yield induced by waterlogging at early and late stages differed from 20–40 % to 3–16 %. Shading at VT stage induced most serious losses of grain yield. The grain yield of summer maize was closely related with the crop biomass accumulation. Shading, waterlogging, and their combination stress significantly decreased leaf area index resulting in serious reduction of the radiation interception. Besides, the leaf SPAD value and photosynthetic rate were also significantly reduced by the stresses, which led to notable reduction in radiation use efficiency (RUE) of summer maize. Thereby, the total accumulated crop biomass was decreased. Moreover, the biomass partitioning to ears was decreased. Accordingly, the 1000-kernel weight and kernels per ear were decreased by the stresses, leading to yield losses. This study explored the differential responses of radiation interception, canopy functionality, and RUE to waterlogging, shading, and their combined stress at different growth stage, furthering our understanding on the yield and growth for summer maize crops under persistent rainfall conditions. • The response of yield components to combined stress at different stage was differed. • Waterlogging at early stage reduced radiation interception and RUE decreasing yield. • Shading at VT lowered incident radiation, decreased kernel setting reducing the yield. • The combined effects of shading and waterlogging on grain yield was greater than single stress. [ABSTRACT FROM AUTHOR]

In the North China Plain (NCP), the deployment of sub-optimal crop management methods has resulted in low maize grain yields and significant environmental costs arising from a low N partial factor productivity (NPFP) and a rampant greenhouse gas emission intensity (GHG i). We hypothesize that in-situ analysis of the grain yield, NPFP and GHG i at local farms might contribute to improving the crop yield, as well as the environmental sustainability of maize production systems. In this study, we investigated the maize production systems deployed at 1574 local farms in the NCP, and quantified the total yield gap (defined as the difference between the yield potential as simulated by the DSSAT-CERES-Maize model and the actual yield achieved by farmers) and the exploitable yield gap (defined as the difference between the attainable yield as calculated by using the Boundary Line Function (BLF) analysis and the average actual yield achieved by farmers). By combining the results from crop modelling, farmer survey data, and on-farm trials, we were able to identify the dominant factors driving the variability in summer maize yield, NPFP, and GHG i. The results revealed that the average grain yield for summer maize in the NCP was 8.3 t ha−1, and that the total and exploitable yield gaps were 4.9 t ha−1 and 3.0 t ha−1, respectively. The average NPFP was 41 kg kg−1, which amounts to 54% of the attainable NPFP. The average GHG i was 463 kg CO 2 eq t−1 grain, which constitutes an increase of 119% over the attainable GHG i. The main factors driving yield include the harvest date and the planting density, and the main factors driving NPFP and GHG i include the N, P and K fertilization rate, where it should be noted that these factors exhibit regional differences. After testing our optimized integrated agronomic management measures in the field experiments, we could confirm that it is possible to narrow the yield gap by 2.7 t ha−1, increase NPFP by 38%, and reduce GHG i by 28%. Obviously, optimizing integrated agronomic management has a great potential for narrowing the yield gap and improving the sustainability of agricultural production. • The total and exploitable yield gaps of maize in the NCP are 4.9 and 3.0 t ha−1. • The main factors driving yield include the harvest date and the planting density. • The N, P and K fertilization rate driving the variability in NPFP and GHG i. • Agronomic optimizations can improve the yield and sustainability of farms in the NCP. [ABSTRACT FROM AUTHOR]

In maize, inferior grains (IG) located on the upper part of the ear have poor grain filling process compared to superior grains (SG) located on the middle and lower parts of the ear. This difference limits satisfactory yield and quality; however, the underlying molecular mechanisms remain unknown. Here, using the isobaric tag for relative and absolute quantification (iTRAQ) technology, the proteomes of IG and SG during early and middle grain filling stages were investigated. In total, 4720 proteins were identified in maize grain and 305 differentially accumulated proteins (DiAPs) were detected between IG and SG. These DiAPs were involved in diverse cellular and metabolic processes with preferred distribution in protein synthesis/destination and metabolism. Compared to SG, DiAPs related to cell growth/division and starch synthesis were lag-accumulated and down-regulated in IG, respectively, resulting in smaller sink sizes and lower sink activities in IG. Meanwhile, impediment of the glycolysis pathway in IG may lead to reduce energy supply and building materials for substance synthesis. Additionally, reactive oxygen species (ROS) homeostasis and the defense system were disturbed in IG, which might lead to reduce protection against various environmental stresses. The present study provides new information on the proteomic differences between IG and SG, and explains possible molecular mechanisms for poor grain filling in IG. [ABSTRACT FROM AUTHOR]

The objective of this paper is to investigate the influence of fine particle bombardment (FPB) on the scuffing behavior of ductile cast iron. Ductile cast iron samples were processed by FPB treatment, in which three injection air pressures (0.2 MPa, 0.4 MPa and 0.6 MPa) were used for given particle flux (8–10 g/s), treatment time (15 s), nozzle diameter (9 mm) and standoff distance (100 mm). Surface morphology, microstructure and hardness of these samples were examined. Step–loading scuffing tests were then performed on a block-on-ring machine, in which the FPB treated ductile cast iron was used for the block and an alloy cast iron without FPB treatment was used for the ring. The test results show that FPB treatment improves the surface hardness of ductile cast iron by nanocrystallization. An increment of injection air pressure would increase the surface hardness through reducing the grain size within the nanocrystalline layer. FPB treatment decreases the friction coefficient through reducing the surface roughness and producing a micro–dimpled surface. The friction coefficient is decreased when increasing the injection air pressure. The scuffing resistance of ductile cast iron depends on surface hardness and friction coefficient; it would be improved through using a higher injection air pressure during the FPB treatment. [ABSTRACT FROM AUTHOR]

Root growth and development of summer maize ( Zea mays L.) is an important process in determining grain yield. In comparison to the information on above ground plant responses only limited knowledge exists on the response of root growth and development to integrated agronomic practices management (defined as a comprehensive management framework consisted of tillage method, plant density, seeding and harvest date, and fertilizer application) under field conditions. Two experiments, integrated agronomic practices management (IAPM) and nitrogen rate testing (NAT) were used to determine the effects on summer maize root system in the course of five years in North China. IAPM consisted of four treatments (CK: local conventional cultivation practices, Opt-1: an optimized combination of cropping system and fertilizer treatment, HY: treatment based on high-yield studies, and Opt-2: a further optimized combination of cropping system and fertilizer treatment). NAT had four treatments of nitrogen rate (0, 129.0, 184.5, and 300.0 kg N ha −1 ).Individual/population root dry weight, individual/population absorption area, surface, volume, and length density of root and grain yield were measured. Roots were sampled per plot at six-leaf stage (V6), tasseling stage (VT), milk stage (R3) and physiological maturity stage (R6). The results from IAPM revealed that Opt-2 significantly increased dry weight, volume, superficial area, and length density of root across the 0–30 cm soil layer of whole growth period. Root active absorption area of Opt-2 exhibited a significant increase in the 0–30 cm soil layer of whole growth period except V6. In compare with root/shoot ratio of CK, this of Opt-2 increased by 14.5% at VT and 16.3% at R6. Results from NAT revealed that N with a range from 0 to 184.5 kg N ha −1 played a positive role in root growth and development. Dry weight, absorbing area of root, and the root/shoot ratio increased as N rate rise within certain limits and then decreased significantly. Dry weight, the proportion of deeply distributed, absorption area, length density of root, and root/shoot ratio increased due to appropriate population, reasonable fertilizer management, and suitable harvest date, which provided sufficient nutrients and moisture to aboveground parts for growth, development, and high grain yield of summer maize. [ABSTRACT FROM AUTHOR]

The objective of this research was to determine the influence of applying a hybrid treatment, consisting of fine particle bombardment (FPB) and powder impact plating (PIP), on the scuffing behavior of ductile cast iron. Ductile cast iron samples were processed by an FPB treatment, a PIP treatment, and a hybrid treatment of both FPB and PIP. Scuffing behavior of these samples was investigated using block-on-ring tests. A piston alloy of ductile cast iron was used for the block and a cast iron cylinder alloy was used for the ring. Results showed that scuffing resistance depends on surface hardness and friction coefficient for the test samples. FPB treatment of block samples increases their surface hardness by nanocrystallization and reduces the friction coefficient of the tribological pair by reducing the surface roughness and producing a micro-dimpled surface. Thus, the scuffing resistance of FPB treated block is improved. The scuffing resistance is also improved by PIP treatment, which reduces the friction coefficient by producing a soft Sn film on the contact surface. After a hybrid treatment of both FPB and PIP, the surface hardness of the ductile cast iron substrate is increased and the friction coefficient of the tribological pair is further reduced relative to either single treatment. Therefore, hybrid treatments such as the ones described here can improve the scuffing resistance of cast irons. [ABSTRACT FROM AUTHOR]

The object of this paper is to investigate the influence of solid solution strengthening on the spalling behavior of railway wheel steel. White etching layer (WEL) was reproduced by twin-disc test and analyzed by phase transformation kinetic. Spalling of WEL was then evaluated by rolling contact fatigue (RCF) test and finite element analysis. The results show that solid solution strengthening improves the resistance to WEL formation for wheel steel through increasing the austenitization temperature. WEL remarkably reduces the RCF life of wheel steel. Whether containing WEL or not, solid solution strengthened steel exhibits a better rolling contact fatigue strength than the traditional wheel steel. [ABSTRACT FROM AUTHOR]

• Effect of artificial notches is studied in terms of fatigue crack non-propagation behaviors. • Non-propagation crack rate firstly increases and then decreases with the increased notch depth. • Gradient residual stress and microstructure are responsible for the crack non-propagation. • Crack traces of post-mortem specimen in the hardened layer and the matrix are compared. Abnormal damages in railway axles can lead to a significant hazard to running safety and reliability. To this end, a surface treatment was selected to effectively inhibit fatigue crack initiation and growth. In this study, a single-edge notch bending fatigue test campaign with artificial notches was conducted to elucidate the fatigue crack non-propagation behavior in railway S38C axles subjected to an induction hardening process. The fatigue cracking behavior in the gradient structure was revealed by optical microscopy, electron backscatter diffraction, and fractography. The microhardness distribution was measured using a Vickers tester. The obtained results show that the microhardness of the strengthening layer is nearly triple that of the matrix. Owing to the gradient microstructures and hardness, as well as compressive residual stress, the fatigue long crack propagates faster once it passes through the hardened zone (approximately 2.0 mm in the radial depth). Thereafter, local retarding (including deflection, branching, and blunting) of the long crack occurs because of the relatively coarse ferrite and pearlite in the transition region and matrix. Totally, this fatigue cracking resistance is reasonably believed to be due to the gradient microstructure and residual stress. These findings help to tailor a suitable detection strategy for maximum defects or cracks in railway axles. [ABSTRACT FROM AUTHOR]

The maize production sector in the North China Plain (NCP) is facing the dual pressures of having to increase its grain yield and improve its environmental sustainability. Evaluating the yield gap and ascertaining the factors that limit the grain yield might suggest new approaches to address these challenges. The objective of this study was to estimate the yield potential and the yield gap associated with smallholdings in the NCP using a hybrid method; to determine the factors driving the grain yield and corresponding sustainability indicators; and to evaluate to what degree the introduction of scientifically developed high-yield and high-efficiency agronomic practices (HH) to smallholders might help to sustainably narrow the exploitable yield gap. Combined with diagnostic smallholder survey and crop modeling exercise to characterize and decompose yield gaps. With survey data, we assessed the existing variation with respect to various key performance indicators and carried out a number of controlled comparative experiments at farms (HH vs traditional farming practices (FP)) in multiple locations. Our work revealed the total and exploitable yield gap were 4.3 t ha−1 and 1.8 t ha−1 for rainfed summer maize, and 4.4 t ha−1 and 1.9 t ha−1 for irrigated summer maize across the entire NCP, indicating a large potential for yield improvements. The main factors driving the yield from the entire region were the planting density, the fertilization frequency, and the irrigation frequency. It should be noted that farmers whose yield was in the top 25% bracket of the yield distribution also achieved relatively high utilization efficiencies with respect to N, P, and K fertilizers (15%, 16%, and 16% above the average values, respectively) while their profit was 41% above average. Comparative experiments conducted over several seasons support insights from surveys by demonstrating that major gains in grain yield (+30%), the fertilizer utilization efficiency (+37% in N partial factor productivity, +48% in P partial factor productivity, and + 32% in K partial factor productivity) and economic profit (+62%) are achievable through the adoption of HH. Through a hybrid method, our results suggest that agricultural intensification can be achieved in the NCP without having to trade off yield against environmental sustainability. Evidently, smallholders can simultaneously improve their maize grain yield, fertilizer utilization efficiency, and profit by adopting straightforward non-disruptive optimizations of their agronomic practices. [Display omitted] • Mixed-method approach used to decompose maize yield gaps with crop model, diagnostic smallholder surveys, and controlled comparative experiments. • We found a sizeable total yield gap (4.3 and 4.4 t ha−1 for rainfed and irrigated maize) in the NCP, of which 1.8 and 1.9 t ha−1 is exploitable. • Main factors driving yield include the planting density, the N topdressing frequency, and the irrigation frequency. • High-yield farms had greater N, P and K fertilizer use efficiencies and increased economic profit. • Smallholder production could be improved by optimize agronomic practices and without having to trade off yield against environmental sustainability. [ABSTRACT FROM AUTHOR]