Search

A novel refractive index (RI) sensor based on photonic crystal fiber Mach–Zehnder interferometer (PCF-MZI) was proposed. It was realized by cascading a section of PCF with half-taper collapse regions (HTCRs) between two single mode fibers (SMFs). The relationship between RI sensitivity and interference length of the PCF-MZI was firstly investigated. Both simulation and experimental results showed that RI sensitivity increased with the increase of interference length. Afterwards, influence of HTCR parameters on RI sensitivity was experimentally investigated to further improve the sensitivity. With intensification of arc discharge intensity in HTCR fabrication process, HTCR with larger maximum taper diameter and longer collapsed region length was obtained, which enhanced evanescent field of the PCF-MZI and then generated higher RI sensitivity. Consequently, a high RI sensitivity of 181.96 nm/refractive index unit (RIU) was achieved in the RI range of 1.3333–1.3574. Increasing arc discharge intensity in HTCR fabrication process has the capacity to improve RI sensitivity of PCF-MZI and meanwhile provides higher mechanical strength and longer sensor life compared to the traditional method of tapering the fiber, which improves the RI sensitivity at the cost of reducing mechanical strength of the sensor. This PCF-MZI was characterized by high RI sensitivity, ease of fabrication, high mechanical strength, and robustness. [ABSTRACT FROM AUTHOR]

A novel Mach–Zehnder Interferometer (MZI) formed by cascading two vase-shaped tapers in a single mode fiber (SMF) is proposed in this work. The vase-shaped taper is fabricated by fusion splicing a fiber sphere with a fiber tip by applying strong arc discharge. The curvature sensing characteristic of the proposed vase-shaped taper-based MZI is experimentally investigated, displaying that the interference spectrum has a blue shift with the increase of applied curvature. The sensor realizes a large range measurement of curvature from 0.9284 m −1 to 4.0470 m −1 with sensitivities of −8.41 nm/m −1 and −16.72 nm/ m −1 in the curvature range of 0.9284 m −1 to 2.4564 m −1 and 2.6025 m −1 to 4.0470 m −1 , respectively. Its temperature-curvature cross-sensitivities are −0.0021 m −1 / °C and −0.0011 m −1 / °C in the two measurement ranges, which are lower than the corresponding curvature resolutions which are 0.0024 m −1 and 0.0012 m −1 . The proposed sensor exhibits the advantages of low cost, negligible temperature cross-sensitivity, fine curvature sensitivity and large measurement scale. [ABSTRACT FROM AUTHOR]

All-fiber Mach-Zehnder interferometers (MZIs) working as curvature sensors have been attracting increasing attention. However, previously reported MZI-based curvature sensors with offset or abrupt-taper structures suffer from weak mechanical strength and low curvature sensitivity. In this letter, a robust and highly-sensitive MZI-based curvature sensor formed by cascading two up-tapers in a single mode fiber (SMF) is proposed and experimentally demonstrated. By optimizing structural parameters of the MZI both in simulation and in experiment, a high quality interference spectrum with a maximum extinction ratio (ER) of around 20 dB is obtained, which is crucial in curvature sensing with spectrum intensity variation and interference dip identifiability being considered. Experimental results show that a high curvature sensitivity of −35.41 nm/m −1 is obtained in the range of 0.6846 m −1 – 1.0606 m −1 , which is 2.4 times higher than that of the interferometer with single-mode-multimode-single-mode (SMS) structure. The two up-tapers, featured by great mechanical strength, are fabricated by only fusion pushing together a whole SMF without cleaving procedure, contributing to excellent repeatability and consistency in the sensor fabrication process. Such an all-fiber sensor exhibits advantages of simple configuration, ease of fabrication, excellent mechanical strength, low cost, and high curvature sensitivity. [ABSTRACT FROM AUTHOR]