Search

By considering real wheel and track geometry and structures, as well as their coupled interaction, an explicit finite element method is applied to simulate the transition of wheel–rail rolling from single-point tread contact to two-point tread-flange contact. The evolutions of the contact position, stress magnitude and direction, adhesion–slip distribution, and wheel–rail relative velocities in the two contact patches are considered to investigate the transient dynamic effects during the contact transition. Important findings include that the transition to two-point contact can result in friction saturation and excite waves in the contact, causing local intensification and relaxation of compression, as well as turbulence of the micro-slip; the local relative velocity in the contact patch is a good measure of the dynamic effects. [ABSTRACT FROM AUTHOR]

Polygonal wear is a type of damage commonly observed on the railway wheel tread. It induces wheel-rail impacts and consequent train/track components failure. This study presents a finite element (FE) thermomechanical wheel-rail contact model, which is able to cope with the three possible generation and development mechanisms of polygonal wear: initial defects, thermal effect, and structural dynamics. The polygonal wear-induced impact contact and further development of wear are simulated. The simulated elastic contact solutions are verified against the program CONTACT. Different material properties (elastic, elasto-plastic and elasto-plastic-thermo, i.e. with thermal softening) and initial polygonal profiles are then applied to the FE model to investigate the influence of wheel/rail material and wear amplitude on wheel-rail contact stress and wear development. The simulations indicate that the wheel-rail impact-induced temperature may reach up to 362 ℃ at the contact interface, and the high temperature at the contact area influences wheel-rail contact stress and wear depth. • An innovative thermomechanical FE model is presented to study polygonal wear growth. • The simulated contact solutions are verified against the program CONTACT. • Using elastic material models causes overestimation of contact stress and wear depth. • Incorporating thermal effects is crucial for wear predication with high slip ratio. • The simulated contact temperature reaches up to 362 ℃ at the wheel-rail interface. [ABSTRACT FROM AUTHOR]

• Weld-induced rail squats are studied through a five-year continual field monitoring and numerical simulations. • Different stages in the development of squats were observed in the field monitoring. • The development process is presented, from inhomogeneous material in HAZs to two-lung-shaped squats associated with cracks. • The formation mechanism in terms of dynamic contact force and differential plastic deformation is proposed. • Numerical simulations are performed to verify the pre-cracking process. Weld-induced squats are a major damage type in high-speed railways as well as in conventional railways. They incur high maintenance costs and endanger operational safety. This paper first presents and analyzes five-year continual field monitoring observations and measurements of squats at rail welds. A hypothesis of the formation and development process of the squats is proposed, which includes three steps. Steps 1 and 2 are pre-cracking, and Step 3 is post-cracking. To verify the pre-cracking process, a three-dimensional (3D) finite element (FE) model is then built up to simulate the vehicle-track interaction with detailed consideration of the local wheel-rail frictional rolling contact. Not only dynamic contact forces but also plastic deformation and wear are calculated. Starting from a smooth rail surface with varying yield stress derived from field-measured hardness, the numerical analysis confirms the hypothesis that the varying hardness at heat-affected zones (HAZs) leads to initial V-shaped irregularities due to differential plastic deformation. Afterward, the surface irregularities excite the dynamic longitudinal contact force, which in turn produces a W-shaped surface pattern through further differential plastic deformation. The growth of the W-shaped pattern leads to the formation of squats. This work provides insight into the squat formation process at rail welds and suggests that welding quality control in terms of hardness variation in the HAZs could reduce or even avoid squats. Early detection of squats with dynamics-based methods is possible. [ABSTRACT FROM AUTHOR]

• We compared the failure of railway thermite welds through real field-testing. • We simulated the dynamic impact force induced by the weld geometry. • We reported the progression of the surface hardness of welds in track condition. • We discussed the noticed failures; wear and cracks. This paper details the field-testing approach and results of thermite welds used in railway applications. Rail steels made from R260 grades are welded by two different processes: the standard process according to the European standards, and a recent technology. Welds are introduced in the same testing location to ensure comparable loading conditions in the aim of studying their degradation behaviours. The total testing-period is 6 months. During the in-service period, the surface hardness of the running band, in the welded area, is recurrently measured. For an accurate assessment of field results, a vehicle/track interaction (VTI) model evaluated the expected dynamic loads induced by the initial vertical irregularities. The simulations show that the highest dynamic load at the wheel/rail contact happens at the location of the maximum absolute gradient, in accordance with previous research. Particularly, dipped welds show relatively high dynamic forces inducing a high loss of the transversal profile. In respect of the field results, the comparison of initial and final surface hardness indicates a significant increase for 'ALFONS' welds over the welded areas. Additionally, all welds depicted a cyclic increase and decrease of the running band hardness. This result is discussed according to the ratcheting susceptibility of welds and eventual wear progression. For a testing-period of 10 weeks, the gauge corner of one 'ALFONS' weld developed a crack. The assessment of the longitudinal profiles revealed changes of the vertical irregularities that may modify the dynamic loads, and further the rolling contact fatigue mechanisms and degradation rates. [ABSTRACT FROM AUTHOR]