Search

Geothermal pavements can be used with ground-source heat pump systems to sustainably provide energy for heating and cooling by incorporating ground heat exchanger elements underneath pavement surfaces. This work investigates the suitability of geothermal pavements at scale, adopting the city of Cardiff, UK, as a case-study. A two-scale modelling framework, combining detailed small-scale with holistic large-scale approaches, is presented, incorporating the accuracy of the former with the continuity of the latter. The results show that between 184 kWh and 345 kWh of thermal energy per metre length of pavement can be supplied annually, depending on soil profile. Moreover, geothermal operation can reduce anthropogenic heat flux into the ground from heated basements, and its associated negative impacts, by about 390 MWh/year. A city-scale analysis using population-consistent geographic areas called LSOAs, estimates that geothermal pavements can supply about 23% of the entire city residential heat demand, or up to 75% with heat sharing between LSOAs. The suitability of geothermal pavements for larger LSOAs is highlighted, supplying up to 100% of the annual domestic heat demand. Investigating the carbon emissions of heating and cooling technologies shows potential reductions of up to 75% when replacing gas boilers and resistance heating with geothermal pavement systems. • Two-scale modelling is used to assess city-scale geothermal pavement potential. • Depending on ground conditions, 184–345 kWh annually/m road of heat can be provided. • Geothermal pavements can reduce anthropogenic heat flux into the ground by ∼ 390 MWh/a. • In low population density areas 100% residential demand can be fulfilled, overall 23%. • Replacing traditional systems can reduce carbon emission by ∼ 75%. [ABSTRACT FROM AUTHOR]

True morphology imaging of individual nanoprobes with high sensitivity and in situ dynamic response is crucial in the dark-field microscopy imaging analysis. However, the geometry and orientation of the probes are experimentally challenging to visualize as their physical dimensions are usually below the diffraction limit. In this work, two-dimensional triangular gold nanoplates (AuNPLs) with the edge length > 600 nm and the thickness ~25 nm displayed clear triangular-shaped far-field scattering patterns (TFSPs) under a dark-field imaging system owing to the strong electrical field strength around the sharp edges and tips. Thus, their actual shape and orientation specific scattering image are directly visualized only by dark-field microscopy and furtherly applied to real-time monitor the etching and alloying progress of AuNPLs. The results showed that the reactive sites of AuNPLs are located at their vertices and sharp edges owing to the sensitive edge effect. This work provides a new perspective to directly monitor the conformation and dynamics of chemical reaction at the single particle level. Two-dimensional triangular gold nanoplates (AuNPLs) with the edge length > 600 nm and the thickness as 25 nm displayed clear triangular-shaped far-field scattering patterns (TFSPs) under a DFM system owing to the strong electrical field strength around the sharp edges and tips. Thus, their actual shape and orientation specific scattering image are directly visualized only with a DFM imaging system and furtherly applied to real-time monitor the etching and alloying progress of AuNPLs. [Display omitted] [ABSTRACT FROM AUTHOR]

• Long-term exposure to PM 2.5 are associated with large- and small- airway function. • Organic matter and nitrate show stronger associations with lung function than PM 2.5. • Exposure to PM 2.5 constituents might be more important in impairing lung function. The associations of long-term exposure to various constituents of fine particulate matter (≤2.5 μm in aerodynamic diameter, PM 2.5) air pollution with lung function were not clearly elucidated in developing countries. The aim was to evaluate the associations of long-term exposure to main constituents of PM 2.5 with lung function in China. This is a nationwide, cross-sectional analysis among 50,991 study participants from the China Pulmonary Health study. Multivariable linear regression models were used to obtain differences of forced expiratory volume in 1 s (FEV 1), forced vital capacity (FVC), FEV 1 /FVC, peak expiratory flow (PEF), and forced expiratory flow at 25–75% of exhaled FVC (FEF 25-75%) associated with an interquartile range (IQR) change of PM 2.5 or its constituents. Residential annual PM 2.5 levels varied from 26 μg/m3 to 92 μg/m3 (average: 53 μg/m3). An IQR increase of PM 2.5 concentrations was associated with lower FEV 1 (19.82 mL, 95% CI: 11.30–28.33), FVC (17.45 mL, 95% CI: 7.16–27.74), PEF (86.64 mL/s, 95% CI: 59.77–113.52), and FEF 25-75% (31.93 mL/s, 95% CI: 16.64–47.22). Black carbon, organic matter, ammonium, sulfate, and nitrate were negatively associated with most lung function indicators, with organic matter and nitrate showing consistently larger magnitude of associations than PM 2.5 mass. This large-scale study provides first-hand epidemiological evidence that long-term exposure to ambient PM 2.5 and some constituents, especially organic matter and nitrate, were associated with lower large- and small- airway function. [ABSTRACT FROM AUTHOR]

Herein, we proposed a new strategy to enhance compatibility and flame retardancy of the immiscible and flammable polylactic acid (PLLA)/polypropylene (PP) blend materials simultaneously. It is found that the boehmite nanorods are located at the PLLA-PP interface by in-situ reactions and the compatibility between phases is greatly improved, resulting in significant enhancement of mechanical properties and flame retardancy: tensile strength and elongation at break of the blends with 7 wt% reactive nanorods are 163% and 601% higher than that without nanorods, respectively. Meanwhile, the peak heat release rate (PHRR) decreases 51.4% and limiting oxygen index (LOI) increases 22.6%. The synergetic improvements are directly attributed to the strengthened interface and the interface takes the role of the flame retarding belt. The research opens a new avenue to fabricate non-halogen flame retardant multicomponent polymer materials with simultaneously enhanced mechanical properties. [Display omitted] •Ternary Poly(L-lactic acid)/Polypropylene/boehmite nanorods nanocomposites were prepared. •Epoxide groups modified boehmite nanorods are thermodynamically located at the PLLA/PP blend interface by the in-situ reactions. •The interfacially located nanorods improve the mechanical properties and flame retardancy of the PLLA/PP blends simultaneously. [ABSTRACT FROM AUTHOR]

At present, anti-angiogenic drugs (AADs) are widely used in the systemic treatment of hepatocellular carcinoma (HCC) or other types of cancer, and have achieved good anti-cancer effect, whereas treatment-related proteinuria can affect the routine use of AADs, which in turn abates the overall efficacy. Currently, most clinicians prescribe angiotensin-converting enzyme inhibitors (ACEIs) to alleviate proteinuria according to diabetic nephropathy guidelines or expert recommendations. However, the efficacy of ACEIs in reducing AAD-related proteinuria and its effect on the anticancer effect of AADs is unknown. Our clinical data showed that some HCC patients experienced tumor progression by ACEIs administration for the treatment of proteinuria caused by AADs. Here, we confirmed that in different tumor-bearing mouse models, ACEIs did not delay the appearance of proteinuria or alleviate proteinuria caused by AADs but compromised the anticancer efficacy of AADs. This effect is unrelated to the change in the VEGF signaling pathway. Our data showed that the combination of ACEIs and AADs flared the production of kidney-derived erythropoietin (EPO). In turn, EPO compromises the anti-angiogenic effects of AADs and decreases antitumor activity. In conclusion, for the treatment of proteinuria caused by AADs, ACEIs have no efficacy while also promoting AADs resistance. This finding is of great significance to guide clinical standardized management of side effects of anti-angiogenic therapy for cancer patients. • ACEIs cannot reduce or delay proteinuria caused by AADs. • ACEIs alone do not promote tumor growth of liver cancer subcutaneous tumor. • High doses of AADs easily induce stable proteinuria, but the anticancer effect is better. • Proteinuria caused by AADs is reversible after withdrawal. • ACEIs promotes the production of kidney-derived EPO and reduces the anticancer efficacy of AADs. [ABSTRACT FROM AUTHOR]

• PCSK9 inhibition ameliorated cardiac inflammation of EAM mice by reducing Th17 cell differentiation. • PCSK9 was expressed by CD4+ T cells, CD8+ T cells, macrophages, and cardiomyocytes in the heart of experimental autoimmune myocarditis (EAM) mice. • PCSK9 promoted Th17 cell differentiation through LDLR/STAT3/ROR-γt pathway. • PCSK9 is a promising target in myocarditis, and inhibition of PCSK9 may provide new therapeutic strategies for patients with myocarditis. Proprotein convertase subtilisin kexin type 9 (PCSK9) was characterized as a protein regulating circulating cholesterol metabolism; however, recent studies demonstrated a role for PCSK9 in inflammatory and autoimmune diseases unrelated to cholesterol alterations. The implication of PCSK9 in myocarditis is unclear and we aim at investigating the roles and mechanisms of PCSK9 in myocarditis. Male BALB/c mice received subcutaneous immunization with MyHC-α peptide on days 0 and 7 to establish the experimental autoimmune myocarditis (EAM) model. PCSK9 inhibitor, evolocumab, was administered subcutaneously once a week starting on day 0 and all mice were euthanized on day 21. Our results showed that PCSK9 inhibition ameliorated the cardiac inflammation of EAM mice. PCSK9 inhibition reduced both the levels of cardiac and peripheral blood PCSK9. We found that CD4+ T cells, CD8+ T cells, macrophages, and cardiomyocytes in the heart of EAM mice could express PCSK9. PCSK9 inhibition decreased the differentiation of cardiac Th17 cells by lowering ROR-γt levels but had no effects on Th1, Th2, and Treg cell differentiation. In vitro experiments of CD4+ T cells, we found that PCSK9 directly promoted Th17 cell differentiation through LDLR/STAT3/ROR-γt pathway. Collectively, we demonstrated that PCSK9 inhibition ameliorated the severity of EAM mice by reducing Th17 cell differentiation. PCSK9 is a promising target for treating myocarditis. [ABSTRACT FROM AUTHOR]

Reactive polymer processing is an effective and environmentally-friendly means of preparing new materials based on combining components with various properties. Numerous investigations have been carried out to explore the reaction processes that occur during the melt blending of polymers. However, reactive processing is far from fully understood because it involves a complicated combination of shear and extensional flows as well as high temperatures and pressures. In this work, a two-step compatibilizing strategy (called reactive splicing compatibilization) has been used to compatibilize immiscible Poly(lactic acid) (PLLA)/Poly(butylene adipate- co -terephthalate) (PBAT) blends with two different PBAT molecular weights (termed H-PBAT and L-PBAT, respectively), using styrene- co -glycidyl methacrylate (SG) as the grafting counterpart. Reactive compatibilizers with various architectures were prepared by pre-grafting either PLLA or PBAT (or both) onto the SG main chains. The remaining unreacted epoxide groups of the pregrafted SG underwent in situ reactions to form double grafted copolymers as compatibilizers for the final blends. The reactivity of SG with these polymers was found to decrease in the order of L-PBAT > PLLA > H-PBAT. Reactive compatibilizers having various architectures were applied to PLLA/PBAT blends with compositions ranging from 90/10 to 10/90 (w/w). The most efficient pre-grafted reactive compatibilizer was determined for the blends with certain composition. A higher proportion of H-PBAT had to be pre-grafted onto the SG to achieve the best compatibilization efficiency when increasing the PLLA content in PLLA/H-PBAT blends. In the case of PLLA/L-PBAT blends, PLLA chains had to be pre-grafted onto the SG for the best compatibilization when L-PBAT was the primary component of the blend. These results provide a better understanding of the reactive processing mechanism. Evidently, the dynamic shear applied during melt processing continuously renews the interface between the different phases to provide sites for reactions between the blend components. These reactions are affected by both the reactivity of the components and the contact time, which in turn is determined by the blend composition. The compatibilizers located at the blend interface were found to have very similar symmetrical binary grafted structures for blends with different compositions. Image 1 • A two-step compatibilizing strategy (called reactive splicing compatibilization) has been used to compatibilize the immiscible Poly(lactic acid) (PLLA)/Poly(butylene adipate- co -terephthalate) (PBAT) blends with two different PBAT molecular weights, using styrene-co-glycidyl methacrylate (SG) as the grafting counterpart. • More than 100 compatibilized blends have been prepared and compared the compatibilization effects of the different compatibilizers. • This work demonstrates the locations of the various reactions and the factors affecting the reactive processing. • The work is very important for better understanding the reactive processing, especially the functions of the dynamic shearing, the reactivity and the composition effects. [ABSTRACT FROM AUTHOR]

Use of corticosteroids is common in the treatment of coronavirus disease 2019, but clinical effectiveness is controversial. We aimed to investigate the association of corticosteroids therapy with clinical outcomes of hospitalized COVID-19 patients. In this single-centre, retrospective cohort study, adult patients with confirmed coronavirus disease 2019 and dead or discharged between 29 December 2019 and 15 February 2020 were studied; 1:1 propensity score matchings were performed between patients with or without corticosteroid treatment. A multivariable COX proportional hazards model was used to estimate the association between corticosteroid treatment and in-hospital mortality by taking corticosteroids as a time-varying covariate. Among 646 patients, the in-hospital death rate was higher in 158 patients with corticosteroid administration (72/158, 45.6% vs. 56/488, 11.5%, p < 0.0001). After propensity score matching analysis, no significant differences were observed in in-hospital death between patients with and without corticosteroid treatment (47/124, 37.9% vs. 47/124, 37.9%, p 1.000). When patients received corticosteroids before they required nasal high-flow oxygen therapy or mechanical ventilation, the in-hospital death rate was lower than that in patients who were not administered corticosteroids (17/86, 19.8% vs. 26/86, 30.2%, log rank p 0.0102), whereas the time from admission to clinical improvement was longer (13 (IQR 10–17) days vs. 10 (IQR 8–13) days; p < 0.001). Using the Cox proportional hazards regression model accounting for time varying exposures in matched pairs, corticosteroid therapy was not associated with mortality difference (HR 0.98, 95% CI 0.93–1.03, p 0.4694). Corticosteroids use in COVID-19 patients may not be associated with in-hospital mortality. [ABSTRACT FROM AUTHOR]

At present, anti-angiogenic drugs (AADs) are widely used in the systemic treatment of hepatocellular carcinoma (HCC) or other types of cancer, and have achieved good anti-cancer effect, whereas treatment-related proteinuria can affect the routine use of AADs, which in turn abates the overall efficacy. Currently, most clinicians prescribe angiotensin-converting enzyme inhibitors (ACEIs) to alleviate proteinuria according to diabetic nephropathy guidelines or expert recommendations. However, the efficacy of ACEIs in reducing AAD-related proteinuria and its effect on the anticancer effect of AADs is unknown. Our clinical data showed that some HCC patients experienced tumor progression by ACEIs administration for the treatment of proteinuria caused by AADs. Here, we confirmed that in different tumor-bearing mouse models, ACEIs did not delay the appearance of proteinuria or alleviate proteinuria caused by AADs but compromised the anticancer efficacy of AADs. This effect is unrelated to the change in the VEGF signaling pathway. Our data showed that the combination of ACEIs and AADs flared the production of kidney-derived erythropoietin (EPO). In turn, EPO compromises the anti-angiogenic effects of AADs and decreases antitumor activity. In conclusion, for the treatment of proteinuria caused by AADs, ACEIs have no efficacy while also promoting AADs resistance. This finding is of great significance to guide clinical standardized management of side effects of anti-angiogenic therapy for cancer patients. [ABSTRACT FROM AUTHOR]

Polymer blend nanocomposites with the nanoparticles exclusively located at the interface have attracted significant attention while the compatibilization functions of such nanoparticles in the blends are still controversial. Herein, the pristine boehmite nanorods (p-BNRs) and epoxide group modified boehmite nanorods (m-BNRs) have been synthesized and incorporated in the immiscible Poly(l -lactide)/Poly(1,4-butylene succinate) (PLLA/PBSU) blends. It is found that both p-BNRs and m-BNRs are thermodynamically located at the interface and the phase morphologies of the two nanocomposites are very similar at the same nanofiller loadings. However, the two nanocomposites exhibit different mechanical properties. The PLLA/PBSU blend nanocomposites with m-BNRs show increased elongation at break, enhanced notched impact strength and improved yield strength, as compared with the binary PLLA/PBSU blends. In contrast, p-BNRs lead to drastically deteriorating mechanical properties of the PLLA/PBSU blends even with all p-BNRs located at the interface. The investigation indicates that p-BNRs at the interface have barren surface and are lack of specific interactions with the polymers in the neighboring phases. In contrast, the epoxide groups on m-BNRs reacted with the end carboxylic acid groups of both PLLA and PBSU and the polymer chains were chemically bonded onto the surface of nanorods. The chemically bonded polymer chains on the nanorods at the interface can entangle with the molecular chains of the two polymers to enhance the interfacial adhesion. This paper demonstrates the significance of molecular chain entanglements of the compatibilizing nanoparticles and paves a new possibility to fabricate new materials with simultaneously enhanced strength and toughness. Image 1 • Ternary Poly(l -lactide)/Poly(1,4-butylene succinate)/boehmite nanorods nanocomposites were prepared. • Both pristine boehmite nanorods and epoxide groups modified boehmite nanorods are thermodynamically located at the interface of PLLA/PBSU. • Barren nanorods deteriorate the mechanical properties of PLLA/PBSU blends, but surface grafted nanorods enhance the mechanical properties drastically. • Molecular entanglements of the grafted nanorods are the prerequisite for the compatibilization of immiscible polymer blends. [ABSTRACT FROM AUTHOR]

• Various new morphologies of CeCO 3 OH were synthesized by a facile hydrothermal route. • Ce 2 (CO 3) 3 ⋅6H 2 O was found as an intermediate product in studied synthetic process. • Decomposition behaviors of CeCO 3 OH in H 2 /Ar atmosphere are revealed. • Ceria with higher photocatalytic activity was obtained by decomposing CeCO 3 OH in H 2. The novel tactic that shape-controlled CeO 2- x with excellent photocatalytic activity by designing morphology of CeCO 3 OH and decomposing in hydrogen was proved. [Display omitted] In this work, various new-observed structured CeCO 3 OH were synthesized by a self-assembly hydrothermal method, and a novel tactic to produce CeO 2- x with excellent photocatalytic activity by decomposing CeCO 3 OH in H 2 was proposed and identified. By controlling the synthetic conditions, almond-like, subglobose shape and hollow-sphere of CeCO 3 OH, 3D-broom-like of Ce 2 O 3 · 2CO 2 · nH 2 O (n = (1–2)), and sheet-like of Ce 2 (CO 3) 3 · 6H 2 O were synthesized. The crystal growth and formation of the cerium carbonate compounds were carefully studied using XRD, SEM and TEM. TG, thermodynamic calculation and in-situ XRD were employed to reveal the decomposition behavior of almond-like CeCO 3 OH in air, Ar and H 2. The results show that the decomposition temperatures of CeCO 3 OH in Ar and H 2 are higher than that of in air, and suggest that Ce 2 O 3 has a low thermodynamic stability during the decomposition of CeCO 3 OH in Ar and H 2 , and Ce3+ will be mostly oxidized by H 2 O firstly and then by both of H 2 O and CO 2. The ceria samples obtained by decomposing from CeCO 3 OH in different atmosphere maintain indistinguishable shape and particle size. The XPS, Raman spectra and ESR results indicate that the one obtained in H 2 has the richest surface oxygen vacancies (OVs), narrowest band gap of 3.12 eV, lowest intensity in PL spectra and a significantly enhanced photodegradation ratio of methylene blue. The MB photodegradation ratio after 120 min reaction with the catalysts of CeO 2 -Air, CeO 2 -Ar and CeO 2 -H 2 is 43.14%, 54.43% and 73.41%, with a calculated reaction rate constant of 0.00539, 0.00652 and 0.01097 min-1, respectively. The offered novel tactic of decomposing CeCO 3 OH in H 2 is an efficient and facile technique for active CeO 2- x production. [ABSTRACT FROM AUTHOR]

Reactive compatibilization is an effective method to improve the compatibility of immiscible polymer blends. The in-situ-formed graft/block copolymers should be thermodynamically located at the interface to bridge the neighboring phases. Unfortunately, they are often pulled out of the interface because of the asymmetric molecular structures. Here, we propose a new strategy to compatibilize immiscible polymer blends called reactive splicing compatibilization. Poly (styrene- co -glycidyl methacrylate) (SG) with high glycidyl methacrylate (GMA) content is used as the reactive backbone chain. Both poly (l -lactic acid) (PLLA) and poly (butylene adipate-co-terephthalate) (PBAT) molecular chains can be easily grafted onto the SG main backbone by the reaction of the terminal carboxylic acid groups with the epoxide groups in the melt. Direct melt blending SG with PLLA and/or PBAT leads to reactive compatibilizers with various molecular architectures, which are used for subsequent compatibilization of PLLA/PBAT blends. It was found that the compatibilizer architecture significantly affects the compatibilization efficiency. The best compatibilization occurs with a reactive compatibilizer of SG-g-PBAT with the SG to PBAT weight ratio of 1:2. The compatibilized PLLA/PBAT (50/50 w/w) blend has precise co-continuous phase morphology with very few micelles. The blend exhibits extremely high Charpy notched impact strength of 90.2 kJ/m2 and tensile strength of 33.3 MPa. The principle of the facile splicing compatibilization strategy is highly applicable to many other immiscible blends with both components containing reactive groups. We report the splicing compatibilization strategy for immiscible polymer blends. The compatibilizer architecture effects on the compatiblization efficiency were investigated. Image 1 • New compatibilization strategy called reactive splicing compatibilization was proposed. • Reactive comb compatibilizers with various architectures were synthesized by melt blending. • Molecular architecture effects on compatibilization of PBAT/PLLA blends were investigated. • PLLA/PBAT blends with superior toughness and high tensile strength were prepared. [ABSTRACT FROM AUTHOR]