Search

This paper proposed the distributed moving horizon coordinated control scheme for the power balance and economic dispatch problems of micro-grid based on distributed generation. We design the power coordinated controller for each subsystem via moving horizon control by minimizing a suitable objective function. The objective function of distributed moving horizon coordinated controller is chosen based on the principle that wind power subsystem has the priority to generate electricity while photovoltaic power generation coordinates with wind power subsystem and the battery is only activated to meet the load demand when necessary. The simulation results illustrate that the proposed distributed moving horizon coordinated controller can allocate the output power of two generation subsystems reasonably under varying environment conditions, which not only can satisfy the load demand but also limit excessive fluctuations of output power to protect the power generation equipment. [ABSTRACT FROM AUTHOR]

An automatic control algorithm for flattening the gain of a fiber Raman amplifier is derived from the Raman scattering equations. A pseudo-inverse gain matrix is introduced to adjust the powers of the pump lasers. The algorithm is simple, fast, effective, robust and insensitive to the length and type of the fiber. It is demonstrated experimentally that the gain flattening for Raman amplifiers comprising various types and lengths of fiber and with different target gains can be achieved automatically with this algorithm. The algorithm converges for both small and large input signal. Flattened Raman gain with a fluctuation less than 0.40 dB over a 50-nm bandwidth for a 50-km SMF or less than 0.20 dB over a 40-nm bandwidth for a 6.6-km dispersion compensated fiber is realized in the experiment. [Copyright &y& Elsevier]

Abstract: A finite-difference time-domain (FDTD) method combined with a periodic boundary condition is used to analyze the diffraction efficiency of an etched diffraction grating (EDG) demultiplexer coated with a metallic film at the backside. The numerical results show that the diffraction loss is mainly due to the scattering effect of shaded facets of a metal-coated grating at both the polarizations. However, the same shaded facets can produce a higher loss for a TM polarization than that for a TE polarization, which induces a higher polarization dependent loss (PDL) of the demultiplexer. [Copyright &y& Elsevier]

Highlights • To achieve a high sensitivity, the cascaded two Fabry-Perot interferometers sensor with the Vernier effect was proposed. • For the intensity interrogation, the sensor system only required a broadband light source and the photo detector. • The reaction between the Streptomycin monoclonal antibody and Streptomycin-BSA was measured by the sensor for the biosensing application. Abstract In this paper, a novel high-sensitivity optical sensor based on cascaded two Fabry-Perot interferometers (FPIs) has been investigated theoretically and experimentally. In order to improve the sensitivity, the two FP interferometers were designed with slightly different free spectrum ranges (FSRs) to produce Vernier effect. The experimental results showed that the sensitivity of the sensor is 23,794.6 nm/RIU for the wavelength interrogation and 4602.3 dB/RIU for the intensity interrogation, much higher than that of the conventional sensors for the bulk refractive index (RI) sensing. Finally, the reaction between Streptomycin monoclonal antibody and Streptomycin-BSA was measured, showing a great potential for low-cost and portable systems in biochemical sensing. [ABSTRACT FROM AUTHOR]

We demonstrate a distributed Bragg reflector (DBR) fiber laser sensor for simultaneous measurements of axial strain and transverse load, this sensor might be applied in structure health monitoring. In this scheme, transverse load introduces an additional birefringence and consequently a linear beat note frequency change of the orthogonally polarized lasing modes, while the axial strain can be simply deduced from the wavelength shift of the laser. The sensor’s sensitivity is measured to be 1.33 kHz/mg and 1.266 pm/με for lateral load and axial strain respectively. [ABSTRACT FROM AUTHOR]

A critical barrier for the successful development of fiber sensors for bio-chemical processes is their limitedly improved sensitivity, restricted by the sensor structural design. To solve this, in this paper, a novel concept was proposed using functionalised modified magnetic microspheres (MMSs) to "amplify" the effect of target bio-chemical analytes to significantly improve the fiber sensor's sensitivity, which has been demonstrated using human chorionic gonadotropin (hCG) as an example. Two types of antibody hCG, ( β and α , both can specifically bind with hCG), were adhered on the surface of fibre sensor and MMSs respectively. Both hCG and MMSs will be specifically captured by the fibre sensor, where MMSs act as an "amplifier" to improve the sensor sensitivity. Experimentally immunomagnetic detection limit of 0.0001 mIU/mL has been achieved, which is the highest reported so far. This newly developed methodology opens a new direction for sensitivity improvement and could be further explored to applications require ultrahigh sensitivity detections such as earlier medical diagnostics. • Use surface modified magnetic microspheres (MMSs) to "amplify" the signal of target analyte. • Provide "additional" sensitivity improvement for the fabricated sensor. • Demonstrated limit of detection of human chorionic gonadotropin as low as 0.0001 mIU/mL, the best value reported so far. • The concept will be pivotal for applications require ultra-high sensitivity detection such as early medical diagnostics.. [ABSTRACT FROM AUTHOR]