Search

Carbon nanotubes (CNTs) have been widely exploited to improve anodic performance, but information is needed on their long-term stability for improvement. Herein, we prepared a novel CNTs-modified graphite felt (CNTs-GF) by a simple and scalable process and evaluated its long-term performance using anaerobic sludge as inoculum. the MFC with CNTs-GF yielded a sustained enhancement of power output, increasing from 1.93 ± 0.09 W m−2 after 1 month to 2.10 ± 0.05 W m−2 after 3 months and reaching 2.00 ± 0.10 W m−2 after 13 month, indicating the enhancement in electricity generation by the CNTs was not declined over one year. However, the bare GF showed a declining tendency of performance during 13 months. The long-term enhancement can be explained by the facts that the CNTs-GF was beneficial to electrochemically active biofilms (EABs) growth and interacted better with EABs and increased the extracellular electron transfer. Community analysis showed an increase in Geobacter in response to CNTs modification. These results demonstrated that CNTs modification could sustain a superior long-term enhancement in MFC performance.

In this study, novel geopolymers based on solid wastes (coal gangue and red mud) were used in the adsorption of heavy metals (Pb2+ and Cu2+) from solution. The correlations between the composition and quantity of the geopolymer gels and heavy metal adsorption were investigated under various conditions using hydrochloric acid dissolution and spectroscopic techniques. The results showed that the geopolymer gel positively correlated with the Pb2+ and Cu2+ adsorption capacities in the absence of external silica and aluminum. Moreover, external silica and aluminum sources promoted Al2O3 and SiO2 dissolution in the raw materials, which increased and decreased the specific surface areas, respectively. All of the tested geopolymers exhibited Pb2+ and Cu2+ adsorption based on the Langmuir isotherm and the pseudo-second-order kinetic model, with adsorption maxima of 137.7 and 90 mg g−1, respectively. This research first determined the correlation between the geopolymer gel and its heavy metal adsorption performance, and demonstrated industrial waste-based geopolymers could be effectively applied for the removal of heavy metal which can help reduce the burden of waste management and provide new insights about the resource recovery of solid wastes.

A novel anthraquinone-2,6-disulfonate/MnOx-doped polypyrrole film (AQDS/Mn/PPy) electrode was prepared by one-step electropolymerization method and was used to improve performance of a reversible photo-bioelectrochemical cell (RPBEC). The RPBEC was operated in polarity reversion depended on dark/light reaction of alga Chlorella vulgaris by which sequential decolorization of azo dye and mineralization of decolorization products coupled with bioelectricity generation can be achieved. The results showed that formation of uniform AQDS/Mn/PPy film significantly enhanced electroactive surface area and electrocatalytic activity of carbon electrode. The RPBEC with AQDS/Mn/PPy electrodes demonstrated 77% increases in maximum power and 73% increases in Congo red decolorization rate before polarity reversion, and 198% increases in maximum power and 138% increases in decolorization products mineralization rate after polarity reversion, respectively, compared to the RPBEC with bare electrode. This was resulted from simultaneous dynamics improvement in half-reaction rate of anode and photo-biocathode due to enhanced electron transfer and algal-bacterial biofilm formation.

Biocathode microbial fuel cell performances with respect to azo dye decolorization and electricity generation were examined using two anodic inoculums, textile dyeing sludge (MFC-I) and municipal sludge (MFC-M), to determine the potential performance regulation of the MFC via the selection of anodic inoculum. The results showed that the MFC-I exhibited excellent performance in Congo red decolorization, whereas the MFC-M performed well in electricity generation. The MFC-I achieved fast Congo red decolorization with a first-order rate constant k = 0.0501, which was 34% higher than that obtained by MFC-M (k = 0.0375). The MFC-M exhibited 3.22 times higher power output (29 mW/m2 vs. 9 mW/m2) and 38.0% lower anode impedance (749 Ω vs. 1208 Ω) compared to MFC-I. The functional stains isolated from the anodic biofilm of MFC-I were identified as Pseudomonas sp. and Aquamicrobium sp., while isolates from MFC-M belonged to Pseudomonas sp. and Bacillus sp. Four selected isolates were proved to be exoelectrogens and bacterial decolorizer simultaneously but exhibited different bioelectrocatalytic activities and dye decolorizing capabilities, which could partly explain the performance difference between the two MFCs with different anodic inocula.

Aromatic amines (AAs), which are components of synthetic dyes, are recalcitrant to the wastewater treatment process and can accumulate in sludge produced by textile-dyeing, which may pose a threat to the environment. A comprehensive investigation of 10 textile-dyeing plants was undertaken in Guangdong Province in China. The contents and component distributions of AAs were evaluated in this study, and a risk assessment was performed. The total concentrations of 14 AAs (Σ14 AAs) varied from 11 μg g −1 dw to 82.5 μg g −1 dw, with a mean value of 25 μg g −1 dw. The component distributions of AAs were characterized by monocyclic anilines, of which 2-methoxy-5-methylaniline and 5-nitro-o-toluidine were the most dominant components. The risk quotient (RQ) value was used to numerically evaluate the ecological risk of 14 AAs in the environment. The result showed that the 14 AAs contents in textile-dyeing sludge may pose a high risk to the soil ecosystem after being discarded on soil or in a landfill.