Search

The subaxial cervical facets are important load-bearing structures, yet little is known about their mechanical response during physiological or traumatic intervertebral motion. Facet loading likely increases when intervertebral motions are superimposed with axial compression forces, increasing the risk of facet fracture. The aim of this study was to measure the mechanical response of the facets when intervertebral axial compression or distraction is superimposed on constrained, non-destructive shear, bending and rotation motions. Twelve C6/C7 motion segments (70 ± 13 yr, nine male) were subjected to constrained quasi-static anterior shear (1 mm), axial rotation (4°), flexion (10°), and lateral bending (5°) motions. Each motion was superimposed with three axial conditions: (1) 50 N compression; (2) 300 N compression (simulating neck muscle contraction); and, (3) 2.5 mm distraction. Angular deflections, and principal and shear surface strains, of the bilateral C6 inferior facets were calculated from motion-capture data and rosette strain gauges, respectively. Linear mixed-effects models (α = 0.05) assessed the effect of axial condition. Minimum principal and maximum shear strains were largest in the compressed condition for all motions except for maximum principal strains during axial rotation. For right axial rotation, maximum principal strains were larger for the contralateral facets, and minimum principal strains were larger for the left facets, regardless of axial condition. Sagittal deflections were largest in the compressed conditions during anterior shear and lateral bending motions, when adjusted for facet side., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

Traumatic cervical facet dislocation (CFD) is often associated with devastating spinal cord injury. Facet fractures commonly occur during CFD, yet quantitative measures of facet deflection, strain, stiffness and failure load have not been reported. The aim of this study was to determine the mechanical response of the subaxial cervical facets when loaded in directions thought to be associated with traumatic bilateral CFD - anterior shear and flexion. Thirty-one functional spinal units (6 × C2/3, C3/4, C4/5, and C6/7, 7 × C5/6) were dissected from fourteen human cadaver cervical spines (mean donor age 69 years, range 48-92; eight male). Loading was applied to the inferior facets of the inferior vertebra to simulate the in vivo inter-facet loading experienced during supraphysiologic anterior shear and flexion motion. Specimens were subjected to three cycles of sub-failure loading (10-100 N, 1 mm/s) in each direction, before being failed in a randomly assigned direction (10 mm/s). Facet deflection, surface strains, stiffness, and failure load were measured. Linear mixed-effects models (α = 0.05; random effect of cadaver) accounted for variations in specimen geometry and bone density. Specimen-specific parameters were significantly associated with most outcome measures. Facet stiffness and failure load were significantly greater in the simulated flexion loading direction, and deflection and surface strains were higher in anterior shear at the non-destructive analysis point (47 N applied load). The sub-failure strains and stiffness responses differed between the upper and lower subaxial cervical regions. Failure occurred through the facet tip during anterior shear loading, while failure through the pedicles was most common in flexion., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

The complexity of multi-axis spine testing often makes it challenging to compare results from different studies. The aim of this work was to develop and implement a standardized testing protocol across three six-axis spine systems, compare them, and provide stiffness and phase angle limits against which other test systems can be compared. Standardized synthetic lumbar specimens (n=5), comprising three springs embedded in polymer at each end, were tested on each system using pure moments in flexion-extension, lateral bending, and axial rotation. Tests were performed using sine and triangle waves with an amplitude of 8Nm, a frequency of 0.1Hz, and with axial preloads of 0 and 500N. The stiffness, phase angle, and R 2 value of the moment against rotation in the principal axis were calculated at the center of each specimen. The tracking error was adopted asa measure of each test system to minimize non-principal loads, defined as the root mean squared difference between actual and target loads. All three test systems demonstrated similar stiffnesses, with small (<14%) but significant differences in 4 of 12 tests. More variability was observed in the phase angle between the principal axis moment and rotation, with significant differences in 10 of 12 tests. Stiffness and phase angle limits were calculated based on the 95% confidence intervals from all three systems. These recommendations can be used with the standard specimen and testing protocol by other research institutions to ensure equivalence of different spine systems, increasing the ability to compare in vitro spine studies., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

Disc degeneration is a common medical affliction whose origins are not fully understood. An improved understanding of its underlying mechanisms could lead to the development of more effective treatments. The aim of this paper was to investigate the effect of (1) degeneration, (2) circumferential region and (3) strain rate on the microscale mechanical properties (toe region modulus, linear modulus, extensibility, phase angle) of individual fibre bundles in the anulus fibrosus lamellae of the human intervertebral disc. Healthy and degenerate fibre bundles excised from different circumferential regions in the outer anulus (posterolateral, lateral, anterolateral, anterior) were tensile tested at slow (0.1%/s), medium (1%/s) and fast (10%/s) strain rates using a micromechanical testing system. Our preliminary results showed that neither degeneration nor circumferential region significantly affected the fibre bundles' mechanical behaviour. However, when the fibre bundles were tested at higher strain rates, this resulted in significantly higher linear moduli and lower phase angles. These findings, compared with data from other studies investigating single and multiple lamellae sections, suggest that degeneration has minimal effect on outer anulus mechanics irrespective of structural level, and the inter- and intra-lamellar arrangement and continuity of the fibre bundles may influence the lamellae's regional behaviour and viscoelasticity., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

Reconstruction of the eyelid remains challenging due to the unique properties of the tarsal plate, which is a fibrocartilagenous structure within the eyelid providing structural support and physical form. There are no previous studies investigating the biomechanical properties of tarsus tissue, which is vital to the success of bioengineered tarsal substitutes. We therefore aimed to determine the biomechanical properties of human tarsus tissue, and used a CellScale BioTester 5000 (CellScale, Waterloo, Canada) to perform uniaxial tensile tests on ten samples of healthy eyelid tarsus. All samples were tested 'fresh' within two hours of harvest. A tensile preload of 50 mN was applied for 10 min before the sample was subjected to uniaxial tension under linear ramp displacement control. Maximum strain was 30% of the original tissue length and thirty dynamic cycles were performed at a strain rate of 1%/s using a triangular waveform. Of the samples tested, the mean (SD) width was 5.51 mm (1.45 mm) whilst mean thickness was 1.6mm (0.51 mm). The mean toe modulus was 0.14 (0.10) MPa, elastic modulus was 1.73 (0.61) MPa, with an extensibility of 15.8 (2.1)%, and phase angle of 6.4° (2.4)°. After adjusting for the initial tissue slack, the maximum strain ranged from 23.8% to 30.0%. At maximum strain, it was observed that the linear region of the stress-strain curve was reached without the sample slipping out of the clamps. Our results establish a benchmark for native tarsus tissue, which can be used when evaluating tissue engineered tarsal substitutes in the future., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Understanding the kinematics of the carpus is essential to the understanding and treatment of wrist pathologies. However, many of the previous techniques presented are limited by non-functional motion or the interpolation of points from static images at different postures. We present a method that has the capability of replicating the kinematics of the wrist during activities of daily living using a unique mechanical testing system. To quantify the kinematics of the carpal bones, we used bone pin-mounted markers and optical motion capture methods. In this paper, we present a hammering motion as an example of an activity of daily living. However, the method can be applied to a wide variety of movements. Our method showed good accuracy (1.0-2.6°) of in vivo movement reproduction in our ex vivo model. Most carpal motion during wrist flexion-extension occurs at the radiocarpal level while in ulnar deviation the motion is more equally shared between radiocarpal and midcarpal joints, and in radial deviation the motion happens mainly at the midcarpal joint. For all rotations, there was more rotation of the midcarpal row relative to the lunate than relative to the scaphoid or triquetrum. For the functional motion studied (hammering), there was more midcarpal motion in wrist extension compared to pure wrist extension while radioulnar deviation patterns were similar to those observed in pure wrist radioulnar deviation. Finally, it was found that for the amplitudes studied the amount of carpal rotations was proportional to global wrist rotations., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

During insertion of a cancellous bone screw, the torque level reaches a plateau, at the engagement of all the screw threads prior to the screw head contact. This plateau torque (T(Plateau)) was found to be a good predictor of the insertion failure torque (stripping) and also exhibited strong positive correlations with areal bone mineral density (aBMD) in ovine bone. However, correlations between T(Plateau) and aBMD, as well as correlations between T(Plateau) and bone microarchitecture, have never been explored in human bone. The aim of this study was to determine whether T(Plateau), a predictor of insertion failure torque, depends on aBMD and/or bone microarchitecture in human femoral heads. Fifty-two excised human femoral heads were obtained. The aBMD and microarchitecture of each specimen were evaluated using dual X-ray Absorptiometry and micro-computed tomography. A cancellous screw was inserted into specimens using an automated micro-mechanical test device, and T(Plateau) was calculated from the insertion profile. T(Plateau) exhibited the strongest correlation with the structure model index (SMI, R=-0.82, p<0.001), followed by bone volume fraction (BV/TV, R=0.80, p<0.01) and aBMD (R=0.76, p<0.01). Stepwise forward regression analysis showed an increase for the prediction of T(Plateau) when aBMD was combined with microarchitectural parameters, i.e., aBMD combined with SMI (R(2) increased from 0.58 to 0.72) and aBMD combined with BV/TV and BS/TV (R(2) increased from 0.58 to 0.74). In conclusion, T(Plateau), a strong predictor for insertion failure torque, is significantly dependent on bone microarchitecture (particularly SMI and BV/TV) and aBMD., (© 2013 Elsevier Ltd. All rights reserved.)

Background: A gamma irradiation dose of 15kGy has been shown to adequately sterilise allograft bone, commonly used in femoral impaction bone grafting to treat bone loss at revision hip replacement, without significantly affecting its mechanical properties. The objective of this study was to evaluate whether use of 15kGy irradiated bone affects the initial mechanical stability of the femoral stem prosthesis, as determined by micromotion in a comprehensive testing apparatus, in a clinically relevant time zero in vitro model of revision hip replacement., Methods: Morselised ovine bone was nonirradiated (control), or irradiated at 15kGy or 60kGy. For each dose, six ovine femurs were implanted with a cemented polished taper stem following femoral impaction bone grafting. Using testing apparatus that reproduces stem loading, stems were cyclically loaded and triaxial micromotion of the stem relative to the bone was measured at the proximal and distal stem regions using non-contact laser transducers and linear variable differential transformers., Findings: There were no significant differences in proximal or distal stem micromotion between groups for all directions (p≤0.80), apart for significantly greater distal stem medial-lateral micromotion in the 60kGy group compared to the 15kGy group (P=0.03), and near-significance in the anterior-posterior direction (P=0.08, power=0.85)., Interpretation: Using a clinically relevant model and loading apparatus, irradiation of bone at 15kGy does not affect initial femoral stem stability following femoral impaction bone grafting., (© 2013.)

Objective: To determine the hydration-over-time behaviour of ovine intervertebral discs and intact joints in a saline bath at body temperature and the effect this has on their stiffness compared to air at ambient temperature., Design: The hydration-over-time behaviour and stiffness of the ovine functional spinal unit and disc were quantified., Background: The fluid content of an intervertebral disc is not constant but varies with external load and load history. The stiffness of ovine functional spinal units in a hydrated environment and how this compares to testing in air have not been quantified., Methods: Intervertebral discs and functional spinal units were weighed and soaked in a saline water bath at 37 degrees C and reweighed each hour for 6 h. They were then allowed to stand in air at room temperature while the time to return to initial weight was recorded. Functional spinal units were randomly assigned to two groups. Axial compression, flexion, extension, lateral bending and axial torsion tests were performed on both the intact functional spinal unit and isolated disc. Group 1 was tested in air then in a saline water bath at 37 degrees C with the testing order reversed for Group 2., Results: Hydration of the disc reached a plateau after an average 3-4 h of soaking with the largest increase seen in the first hour. Four hours, standing in air at room temperature, was required to return specimens to their initial weight. The functional spinal unit stiffness was significantly lower for those specimens tested in the bath compared to air., Conclusions: Ovine intervertebral discs show similar hydration-over-time behaviour when compared to human discs. Stiffnesses in different modes of loading were significantly different when tested in a hydrated environment compared with the standard method of testing in air., Relevance: It has been shown that there are biomechanical and biochemical similarities between sheep and human intervertebral discs. Despite these similarities, no studies have looked at how ovine intervertebral discs behave over time in a hydrated environment. In humans, hydration levels are an important aspect of intervertebral disc degeneration. There is also a relationship between decreased hydration levels and increased stiffness. This study demonstrates the similarities between human and ovine hydration-over-time behaviour. The importance of intervertebral disc hydration and its effects on stiffness under different modes of loading were also demonstrated and have not been previously shown using the ovine model. In this context, the results from this study provide further support for the use of the ovine model.