Search

Background: This study presents a novel multi-technique approach that integrates micro-CT and optical photothermal infrared spectroscopy (O-PTIR) to evaluate polymerisation differences, so-called spatio-temporal polymerisation properties, between flowable and sculptable dental resin-based composites., Methods: Ten commercially available dental composites were investigated, including flowable and sculptable counterparts from the same manufacturer. Eight parameters were evaluated: short-term polymerisation characteristics (degree of conversion after 5 min, maximum polymerisation rate, time to reach maximum polymerisation rate) was measured using ATR-FTIR with real-time monitoring; changes in the degree of conversion with depth were evaluated with O-PTIR, 3D visualisation of shrinkage patterns, overall volumetric shrinkage, depth-specific shrinkage, and porosity were measured using micro-CT; surface morphology with detailed measurements of elemental composition was characterised using SEM/EDX; light transmittance was analysed with a NIST-referenced spectrometer., Results: The study found that the increase in filler weight and volume ratio reduced the degree of conversion and polymerisation shrinkage, while moderately influencing the maximum polymerisation rates. The time to reach maximum polymerisation rates and light transmittance were not dependent on the filler amount. O-PTIR assessed a depth-dependent decrease in the degree of conversion for both composite types, with flowable composites generally showing a greater decrease in the degree of conversion than sculptable composites, except for bulk-fill composites. Micro-CT scans showed significantly higher flowable shrinkage values than their sculptable counterparts, highlighting the performance differences between the two types of composites., Conclusions: The findings of this study have practical implications for the selection and use of dental composites. Flowable composites, despite their higher degrees of conversion and polymerisation rates, also exhibit higher volumetric shrinkage, which can be detrimental for clinical applications. The new measurement methods used in this study provide a comprehensive overview of the polymerisation behaviour of commercially available dental composites, offering valuable insights for material optimisation., (Copyright © 2024 The Authors. Published by Elsevier Inc. All rights reserved.)

Background: Dental resin composites' performance is intricately linked to their polymerisation shrinkage characteristics. This study compares polymerisation shrinkage using advanced 3D micro-computed tomography (micro-CT) and traditional 2D linear assessments. It delves into the crucial role of filler content on shrinkage and the degree of conversion in dental resin composites, providing valuable insights for the field., Methods: Five experimental dental composite materials were prepared with increasing filler contents (55-75 wt%) and analysed using either 3D micro-CT for volumetric shrinkage or a custom-designed linometer for 2D linear shrinkage. The degree of conversion was assessed using Optical Photothermal Infrared (O-PTIR) and Fourier-Transform Infrared (FTIR) spectroscopy. Light transmittance through a 2-mm layer was evaluated using a NIST-calibrated spectrometer. Scanning Electron Microscopy (SEM) and Energy-Dispersive X-ray Spectroscopy (EDX) examined surface morphology and elemental distribution. Correlation between the investigated parameters was determined using Spearman correlation analyses., Results: The study found significant differences in polymerisation-related properties among different filler content categories, with volumetric shrinkage consistently demonstrating higher mean values than linear shrinkage across most groups. Volumetric shrinkage decreased with increasing curing depth, showing no direct correlation between filler content and shrinkage levels at different curing depths. The results highlighted a strong negative correlation between filler content and degree of conversion, volumetric and linear shrinkage, as well as maximum shrinkage rate. Light transmittance showed a moderate correlation with the filler content and a weak correlation with other tested parameters., Conclusions: This study underscores the importance of considering both volumetric and linear shrinkage in the design and analysis of dental composite materials. The findings advocate optimising filler content to minimise shrinkage and enhance material performance. Integrating micro-CT and O-PTIR techniques offers novel insights into dental composites' polymerisation behaviour, providing a foundation for future research to develop materials with improved clinical outcomes., (Copyright © 2024 The Authors. Published by Elsevier Inc. All rights reserved.)

Objectives: Composites with copper-doped mesoporous bioactive nanospheres (Cu-MBGN) were developed to prevent secondary caries by imparting antimicrobial and ion-releasing/remineralizing properties., Methods: Seven experimental composites containing 1, 5 or 10 wt% Cu-MBGN, the corresponding inert controls (silica) and bioactive controls (bioactive glass 45S5) were prepared. The temperature rise during light curing, cross-linking density by ethanol softening test, monomer elution and their potential adverse effects on the early development of zebrafish Danio rerio was investigated., Results: Materials combining Cu-MBGN and silica showed the highest resistance to ethanol softening, as did the bioactive controls. Cu-MBGN composites showed significant temperature rise and reached maximum temperature in the shortest time. Bisphenol A was not detected, while bis-GMA was found only in the control materials and TEGDMA in the eluates of all materials. There was no increase in zebrafish mortality and abnormality rates during exposure to the eluates of any of the materials., Conclusions: The composite with 5 wt% Cu-MBGN combined with nanosilica fillers showed the lowest ethanol softening, indicating the polymer's highest durability and cross-linking density. Despite the TEGDMA released from all tested materials, no embryotoxic effect was observed., Competing Interests: Declaration of Competing Interest The authors of the manuscript „The influence of copper-doped mesoporous bioactive nanospheres on the temperature rise during polymerization, polymer cross-linking density, monomer release and embryotoxicity of dental composites" submitted to Dental Materials declare no conflict of interest. The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript, or in the decision to publish the results., (Copyright © 2024 Elsevier Inc. All rights reserved.)

Objective: Dentists are facing a myriad of new CAD/CAM product for dental filling therapies. Are the new materials any worthwhile using? Are they succeeding the standard filling materials? Here we compare for the first time the new resin-composite blocks (RCBs) with conventional materials (Filtek Z250 and Tetric EvoCeram)., Methods: The material were tested for residual monomer elution by HPLC, thermogravimetric analysis (TG) was used to determine the percentage of fillers by weight, hardness was evaluated by Vickers method, morphology of fillers and distribution in the matrix were examined by scanning electron microscopy (SEM), elemental analysis for elemental determination of the filler particles was performed by energy-dispersive X-ray spectroscopy (EDX) cytotoxicity using human gingival fibroblasts and an epithelial cell line., Results: The RBC outperformed conventional composite regarding mechanical characteristics (hardness) and monomer eluation, but showed some worrisome results regarding cytotoxicity., Significance: The cost benefit is not in favour of RBCs in comparison to conventional composites, as the cytotoxicity was found higher for RBCs., (Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.)

Objectives: The objective of this study was to demonstrate a successful binding of Doxy hyclate onto a titanium zirconium alloy surface., Methods: The coating was done on titanium zirconium coins in a cathodic polarization setup. The surface binding was analyzed by SEM, SIMS, UV-vis, FTIR and XPS. The in vitro biological response was tested with MC3T3-E1 murine pre-osteoblast cells after 14 days of cultivation and analyzed in RT-PCR. A rabbit tibial model was also used to confirm its bioactivity in vivo after 4 and 8 weeks healing by means of microCT., Results: A mean of 141 μg/cm(2) of Doxy was found firmly attached and undamaged on the coin. Inclusion of Doxy was documented up to a depth of approximately 0.44 μm by tracing the (12)C carbon isotope. The bioactivity of the coating was documented by an in vitro study with murine osteoblasts, which showed significantly increased alkaline phosphatase and osteocalcin gene expression levels after 14 days of cell culture along with low cytotoxicity. Doxy coated surfaces showed increased bone formation markers at 8 weeks of healing in a rabbit tibial model., Significance: The present work demonstrates a method of binding the broad spectrum antibiotic doxycycline (Doxy) to an implant surface to improve bone formation and reduce the risk of infection around the implant. We have demonstrated that TiZr implants with electrochemically bound Doxy promote bone formation markers in vitro and in vivo., (Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.)

Objectives: The latest LED dental curing devices claim sufficient curing of restorative materials with short curing times. This study evaluates mechanical and chemical properties as a function of curing time of two commercial composite filling materials cured with three different LED lamps., Methods: The composites were Filtek Z250 (3M ESPE) and Tetric EvoCeram (Ivoclar Vivadent) and the LED curing devices were bluephase 16i (Ivoclar Vivadent), L.E.Demetron II (Kerr) and Mini L.E.D. (Satelec). Control samples were cured with a QTH-lamp (VCL 400, Kerr). The wear resistance after simulated tooth brushing, degree of conversion, curing depth, and amounts of residual monomers were measured after different curing times., Results: The results of this study show that short curing time with high-intensity LEDs may influence the bulk properties of the materials, resulting in lower curing depth and increased residual monomer content. The measured surface properties of the materials, degree of conversion and wear resistance, were not affected by short curing times to the same extent., Significance: This study demonstrates that reduced exposure time with high intensity LEDs can result in composite restorations with inferior curing depth and increased leaching of monomers. Dentists are recommended to use sufficient curing times even with high intensity LEDs to ensure adequate curing and minimize the risk of monomer leaching., (Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.)

Fluoride-modification of dental titanium (Ti) implants is used to improve peri-implant bone growth and bone-to-implant contact and adhesion strength. In this study, the surface topography, chemistry and biocompatibility of polished Ti surfaces treated with hydrofluoric acid solution (HF) were studied. Murine osteoblasts (MC3T3-E1) were cultured on the different groups of Ti surfaces. Surfaces treated with HF had higher roughness, lower cytotoxicity level and better biocompatibility than controls. For short treatment times (40 and 90 s), fluorine was detected only within the first 5 nm of the surface layer (X-ray Photoemission Spectroscopy, XPS), whereas longer treatment time (120 and 150 s) caused fluoride ions to penetrate deeper (Secondary Ion Mass Spectrometry, SIMS). These results suggest that submerging Ti implants in a weak HF solution instigate time-dependant specific surface changes that are linked to the improved biocompatibility of these surfaces.