Search

During a three-day industrial trial, municipal solid waste incineration fly ash (FA) was co-processed in a cement kiln after water-washing pretreatment for waste-to-resource conversion. All inputs and outputs were sampled to obtain the dioxin fingerprints. During washing, the relative contents of polychlorinated dibenzo-p-dioxins and dibenzofurans in FA, washed FA and sludge were basically the same and only a simple physical migration resulted. During drying, only physical processes resulted, which included volatilization and migration. Minimal dioxins residue remained in the clinker, cement kiln dust and flue gas, and the dioxins degraded completely. Through co-processing, the dioxins degraded obviously. The main compounds synthesized include 1,2,3,4,7,8-hepta-chlorodibenzo-p-dioxin, 2,3,7,8-tetra- chlorodibenzofuran and octa-chlorodibenzofuran. A comparison of dioxins fingerprints in the clinker, cement kiln dust and flue gas under baseline and co-processing conditions showed that co-processing had no effect on the cement kiln production. The baseline sample also contained a certain amount of dioxins, possibly because of the 'memory effect' and heterogeneous formations. The dioxins concentrations in the clinker and FA were far lower than the national standards. Thus, no environmental risk results during co-processing., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

The production and use of polychlorinated biphenyls (PCBs) have ceased and most developed countries have disposed off their stocks long time ago. PCBs can however still be found in the environment and one important source is accumulated stocks in developing countries. Sound treatment of PCB is costly and most developing countries do not have dedicated hazardous waste incinerators or non-combustion technologies available for domestic disposal and can usually not afford export. High temperature cement kilns have been used to treat organic hazardous wastes in developed countries for decades and shown to constitute a sound option if well managed and controlled. In contrast to dedicated hazardous waste incinerators and other treatment techniques, cement kilns are already in place in virtually every country and may constitute a treatment option. The objective of this study was therefore to carry out the first test burn with PCB-oil in a developing country cement kiln and to assess its feasibility and destruction performance. The 3 d test burn demonstrated that the Sri Lankan cement kiln was able to destroy PCB in an irreversible and environmental sound manner without causing any new formation of PCDD/PCDF or HCB. The destruction and removal efficiency (DRE) was better than 99.9999% at the highest PCB feeding rate., (Copyright 2009 Elsevier Ltd. All rights reserved.)

Co-processing of hazardous wastes in cement kilns have for decades been thought to cause increased emissions of PCDD/PCDFs--a perception that has been evaluated in this study. Hundreds of PCDD/PCDF measurements conducted by the cement industry and others in the last few years, on emissions and solid materials, as well as recent test burns with hazardous wastes in developing countries do not support this perception. Newer data has been compared with older literature data and shows in particular that many emission factors have to be reconsidered. Early emission factors for cement kilns co-processing hazardous waste, which are still used in inventories, are shown to be too high compared with actual measurements. Less than 10 years ago it was believed that the cement industry was the main contributor of PCDD/PCDFs to air; data collected in this study indicates however that the industry contributes with less than 1% of total emissions to air. The Stockholm Convention on POPs presently ratified by 144 parties, classifies cement kilns co-processing hazardous waste as a source category having the potential for comparatively high formation and release of PCDD/PCDFs. This classification is based on early investigations from the 1980s and 1990s where kilns co-processing hazardous waste had higher emissions compared to those that did not burn hazardous waste. However, the testing of these kilns was often done under worst case scenario conditions known to favour PCDD/PCDF formation. More than 2000 PCDD/PCDF cement kiln measurements have been evaluated in this study, representing most production technologies and waste feeding scenarios. They generally indicate that most modern cement kilns co-processing waste today can meet an emission level of 0.1ngI-TEQ/m(3), when well managed and operated. In these cases, proper and responsible use of waste including organic hazardous waste to replace parts of the fossil fuel does not seem to increase formation of PCDD/PCDFs. Modern preheater/precalciner kilns generally seems to have lower emissions than older wet-process cement kilns. It seems that the main factors stimulating formation of PCDD/PCDFs is the availability of organics in the raw material and the temperature of the air pollution control device. Feeding of materials containing elevated concentrations of organics as part of raw-material-mix should therefore be avoided and the exhaust gases should be cooled down quickly in long wet and long dry cement kilns without preheating. PCDD/PCDFs could be detected in all types of solid samples analysed: raw meal, pellets and slurry; alternative raw materials as sand, chalk and different ashes; cement kiln dust, clinker and cement. The concentrations are however generally low, similar to soil and sediment.