Search

The photo-assisted electrochemical degradation of a real effluent of the atrazine manufacturing process containing atrazine, simazine, hydroxy-triazine and propazine was carried out galvanostatically using a pilot-scale tubular flow reactor prototype containing DSA ® and Ti as cathode. The effluent was mainly characterized by a high amount of NaCl, required in the synthesis route used, and it was used as taken in the factory. The variables for process optimization were the current density (3.0, 6.0, and 9.0 mA cm -2 ) and flow rate (300 and 3,000 L h -1 ). These later values produces laminar and turbulent flow regimes, with Reynolds numbers of 1,100 and 11,000, respectively. None of the four organics contained in the waste is refractory to the photo-electrochemical treatment and they are depleted with the photo-electrolytic technology using large current densities and appropriate electric charge passed. Both direct electrochemical process and mediated anodic oxidation occur during the treatment. First process occurs at turbulent flow condition and low current densities, while the chemical oxidation process happens at laminar flow condition and high current densities. Atrazine and propazine are efficiently removed at laminar flow conditions, with an almost total depletion for the largest current densities. On the contrary, simazine is efficiently removed in turbulent flow conditions and intermediate current density, with removals higher than 90% for 20 kWh m -3 . These results have great significance because they demonstrate the applicability of the electrochemical technology in the treatment of real industrial wastes with a cell specially designed to attain high efficiency in the removal of pollutants., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

The electrooxidation of the dimethyl phthalate (DMP) ester was galvanostatically carried out in a filter-press reactor using a fluoride-doped lead dioxide (β-PbO2,F) film electrodeposited on a Ti substrate. The variables investigated were the nature of the supporting electrolyte (NaCl and Na2SO4), pH (3, 7, and 10), current density (10, 20, 40, 60, and 80mAcm(-2)), and temperature (10, 20, 30, 40, and 50°C). The removal of DMP was monitored through high performance liquid chromatography (HPLC) and total organic carbon (TOC) analysis. The best conditions were obtained using Na2SO4 and at low current densities, independent of the solution pH or temperature. These conditions led to the highest levels of current efficiencies and complete combustion. However, the TOC removal levels were low, due to the generation of highly oxidized intermediates, which was confirmed by the intermediates detected by HPLC., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

This work presents an electrochemical investigation of the benzene oxidation process in aqueous solution on boron-doped diamond (BDD) electrodes. Additionally, in order to determine the main products generated during the oxidation process, electrolysis and high performance liquid chromatography experiments were carried out. The complete degradation of this compound was performed aiming to a further application in waste water treatment. The cyclic voltammetry studies indicate that benzene is irreversibly oxidized in acid medium (H2SO4 0.5 M) on the BDD electrode surface at 2.0 V versus Ag/AgCl in a diffusion controlled process. During the cycling, other products are generated, and a pair of peaks was observed that can be associated with the oxi-reduction of anyone of the following species: hydroquinone, benzoquinone, resorcinol or catechol. The electrolysis experiments were carried out at 2.4 and 2.5 V on the BDD electrode surface in a solution containing 1x10(-2) M of benzene (below the saturation concentration in aqueous solution), for 3 and 5 h, respectively. The main products measured were: hydroquinone, resorcinol, p-benzoquinone, catechol and phenol. The complete electrochemical benzene degradation was performed in the electrolysis experiments using a rotating BDD disc electrode (2.5 V for 5 h) and the main products detected were all measured at concentrations lower than 10(-5) M in this condition. The boron-doped diamond electrode had proved to be a valuable tool for the electrochemical degradation of the benzene, a very stable chemical compound.