Search

Transition metal oxynitrides are a promising class of functional materials for photoelectrochemical (PEC) applications. Although these compounds are most commonly synthesized via ammonolysis of oxide precursors, such synthetic routes often lead to poorly controlled oxygen-to-nitrogen anion ratios, and the harsh nitridation conditions are incompatible with many substrates, including transparent conductive oxides. Here, we report direct reactive sputter deposition of a family of zirconium oxynitride thin films and the comprehensive characterization of their tunable structural, optical, and functional PEC properties. Systematic increases of the oxygen content in the reactive sputter gas mixture enable access to different crystalline structures within the zirconium oxynitride family. Increasing oxygen contents lead to a transition from metallic to semiconducting to insulating phases. In particular, crystalline Zr2ON2-like films have band gaps in the UV-visible range and are n-type semiconductors. These properties, together with a valence band maximum position located favorably relative to the water oxidation potential, make them viable photoanode candidates. Using chopped linear sweep voltammetry, we indeed confirm that our Zr2ON2 films are PEC-active for the oxygen evolution reaction in alkaline electrolytes. We further show that high-vacuum annealing boosts their PEC performance characteristics. Although the observed photocurrents are low compared to state-of-the-art photoanodes, these dense and planar thin films can offer a valuable platform for studying oxynitride photoelectrodes, as well as for future nanostructuring, band gap engineering, and defect engineering efforts.

The instability of perovskite absorbers under various environmental stressors is the most significant obstacle to widespread commercialization of perovskite solar cells. Herein, we study the evolution of crystal structure and microstrain present in naked triple-cation mixed CsMAFA-based perovskite films under heat, UV, and visible light (1 Sun) conditions by grazing-incidence wide-angle X-ray scattering (GIWAXS). We find that the microstrain is gradient distributed along the surface normal of the films, decreasing from the upper surface to regions deeper within the film. Moreover, heat, UV, and visible light treatments do not interfere with the crystalline orientations within annealed polycrystalline films. However, when subjected to heat, the naked perovskite films exhibit a rapid component decomposition, induced by phase separation and ion migration. Conversely, under exposure to UV and 1 Sun light soaking, the naked perovskite films undergo a self-optimization structure evolution during degradation and develop into smoother films with reduced surface potential fluctuations.

We elucidate the role of subsurface oxygen on the production of C2 products from CO2 reduction over Cu electrocatalysts using the newly developed grand canonical potential kinetics density functional theory method, which predicts that the rate of C2 production on pure Cu with no O is ∼500 times slower than H2 evolution. In contrast, starting with Cu2O, the rate of C2 production is >5,000 times faster than pure Cu(111) and comparable to H2 production. To validate these predictions experimentally, we combined time-dependent product detection with multiple characterization techniques to show that ethylene production decreases substantially with time and that a sufficiently prolonged reaction time (up to 20 h) leads only to H2 evolution with ethylene production ∼1,000 times slower, in agreement with theory. This result shows that maintaining substantial subsurface oxygen is essential for long-term C2 production with Cu catalysts.

The binary Ta-N chemical system includes several compounds with notable prospects in microelectronics, solar energy harvesting, and catalysis. Among these, metallic TaN and semiconducting Ta3N5 have garnered significant interest, in part due to their synthetic accessibility. However, tantalum sesquinitride (Ta2N3) possesses an intermediate composition and largely unknown physical properties owing to its metastable nature. Herein, Ta2N3 is directly deposited by reactive magnetron sputtering and its optoelectronic properties are characterized. Combining these results with density functional theory provides insights into the critical role of oxygen in both synthesis and electronic structure. While the inclusion of oxygen in the process gas is critical to Ta2N3 formation, the resulting oxygen incorporation in structural vacancies drastically modifies the free electron concentration in the as-grown material, thus leading to a semiconducting character with a 1.9 eV bandgap. Reducing the oxygen impurity concentration via post-synthetic ammonia annealing increases the conductivity by seven orders of magnitude and yields the metallic characteristics of a degenerate semiconductor, consistent with theoretical predictions. Thus, this inverse oxygen doping approach - by which the carrier concentration is reduced by the oxygen impurity - offers a unique opportunity to tailor the optoelectronic properties of Ta2N3 for applications ranging from photochemical energy conversion to advanced photonics.

The activity of polycrystalline thin film photoelectrodes is impacted by local variations of the material properties due to the exposure of different crystal facets and the presence of grain/domain boundaries. Here a multi-modal approach is applied to correlate nanoscale heterogeneities in chemical composition and electronic structure with nanoscale morphology in polycrystalline Mo-BiVO4 . By using scanning transmission X-ray microscopy, the characteristic structure of polycrystalline film is used to disentangle the different X-ray absorption spectra corresponding to grain centers and grain boundaries. Comparing both spectra reveals phase segregation of V2 O5 at grain boundaries of Mo-BiVO4 thin films, which is further supported by X-ray photoelectron spectroscopy and many-body density functional theory calculations. Theoretical calculations also enable to predict the X-ray absorption spectral fingerprint of polarons in Mo-BiVO4 . After photo-electrochemical operation, the degraded Mo-BiVO4 films show similar grain center and grain boundary spectra indicating V2 O5 dissolution in the course of the reaction. Overall, these findings provide valuable insights into the degradation mechanism and the impact of material heterogeneities on the material performance and stability of polycrystalline photoelectrodes.

Catalysts for electrochemical carbon dioxide reduction in aqueous electrolytes suffer from high energy input requirements, competition with hydrogen evolution from water reduction, and low product selectivity. Theory suggests that plasmonic catalysts can be tuned to selectively lower the energy barrier for a specific reaction in a set of competitive reactions, but there has been little experimental evidence demonstrating plasmon-driven selectivity in complicated multielectron electrochemical processes. Here, the photoactivity at a plasmonically active silver thin film electrode at small cathodic potentials selectively generates carbon monoxide while simultaneously suppressing hydrogen production. At larger cathodic potentials, the photoactivity promotes production of methanol and formate. Methanol production is observed only under illumination, not in dark conditions. The preference of the plasmonic activity for carbon dioxide reduction over hydrogen evolution and the ability to tune plasmonic activity with voltage demonstrates that plasmonics provide a promising approach to promote complex electrochemical reactions over other competing reactions.

Si photocathodes integrated with Ag-supported dendritic Cu catalysts are used to perform light-driven reduction of CO2 to C2 and C3 products in aqueous solution. A back illumination geometry with an n-type Si absorber was used to permit the use of absorbing metallic catalysts. Selective carrier collection was accomplished by a p+ implantation on the illumination side and an n+ implantation followed by atomic layer deposition of TiO2 on the electrolyte site. The Ag-supported dendritic Cu CO2 reduction catalyst was formed by evaporation of Ag followed by high-rate electrodeposition of Cu to form a high surface area structure. Under simulated 1 sun illumination in 0.1 M CsHCO3 saturated with CO2, the photovoltage generated by the Si (∼600 mV) enables C2 and C3 products to be produced at -0.4 vs. RHE. Texturing of both sides of the Si increases the light-limited current density, due to reduced reflection on the illumination side, and also deceases the onset potential. Under simulated diurnal illumination conditions photocathodes maintain over 60% faradaic efficiency to hydrocarbon and oxygenate products (mainly ethylene, ethanol, propanol) for several days. After 10 days of testing, contamination from the counter electrode is observed, which causes an increase in hydrogen production. This effect is mitigated by a regeneration procedure which restores the original catalyst selectivity. A tandem, self-powered CO2 reduction device was formed by coupling a Si photocathode with two series-connected semitransparent CH3NH3PbI3 perovskite solar cells, achieving an efficiency for the conversion of sunlight to hydrocarbons and oxygenates of 1.5% (3.5% for all products).

Two-dimensional materials with engineered composition and structure will provide designer materials beyond conventional semiconductors. However, the potentials of defect engineering remain largely untapped, because it hinges on a precise understanding of electronic structure and excitonic properties, which are not yet predictable by theory alone. Here, we utilize correlative, nanoscale photoemission spectroscopy to visualize how local introduction of defects modifies electronic and excitonic properties of two-dimensional materials at the nanoscale. As a model system, we study chemical vapor deposition grown monolayer WS2, a prototypical, direct gap, two-dimensional semiconductor. By cross-correlating nanoscale angle-resolved photoemission spectroscopy, core level spectroscopy, and photoluminescence, we unravel how local variations in defect density influence electronic structure, lateral band alignment, and excitonic phenomena in synthetic WS2 monolayers.

Chemical transformations that occur on photoactive materials, such as photoelectrochemical water splitting, are strongly influenced by the surface properties as well as by the surrounding environment. Herein, we elucidate the effects of oxygen and water surface adsorption on band alignment, interfacial charge transfer, and charge-carrier transport by using complementary Kelvin probe measurements and photoconductive atomic force microscopy on bismuth vanadate. By observing variations in surface potential, we show that adsorbed oxygen acts as an electron-trap state at the surface of bismuth vanadate, whereas adsorbed water results in formation of a dipole layer without inducing interfacial charge transfer. The apparent change of trap state density under dry or humid nitrogen, as well as under oxygen-rich atmosphere, proves that surface adsorbates influence charge-carrier transport properties in the material. The finding that oxygen introduces electronically active states on the surface of bismuth vanadate may have important implications for understanding functional characteristics of water splitting photoanodes, devising strategies to passivate interfacial trap states, and elucidating important couplings between energetics and charge transport in reaction environments.

The performance of energy materials hinges on the presence of structural defects and heterogeneity over different length scales. Here we map the correlation between morphological and functional heterogeneity in bismuth vanadate, a promising metal oxide photoanode for photoelectrochemical water splitting, by photoconductive atomic force microscopy. We demonstrate that contrast in mapping electrical conductance depends on charge transport limitations, and on the contact at the sample/probe interface. Using temperature and illumination intensity-dependent current-voltage spectroscopy, we find that the transport mechanism in bismuth vanadate can be attributed to space charge-limited current in the presence of trap states. We observe no additional recombination sites at grain boundaries, which indicates high defect tolerance in bismuth vanadate. These findings support the fabrication of highly efficient bismuth vanadate nanostructures and provide insights into how local functionality affects the macroscopic performance.

The operando quantification of surface and bulk losses is key to developing strategies for optimizing photoelectrodes and realizing high efficiency photoelectrochemical solar energy conversion systems. This is particularly true for emerging thin film semiconductors, in which photocarrier diffusion lengths, surface and bulk recombination processes, and charge separation and extraction limitations are poorly understood. Insights into mechanisms of efficiency loss can guide strategies for nanostructuring photoelectrodes, engineering interfaces, and incorporating catalysts. However, few experimental methods are available for direct characterization of dominant loss processes under photoelectrochemical operating conditions. In this work, we provide insight into the function and limitations of an emerging semiconductor photoanode, γ-Cu3V2O8, by quantifying the spatial collection efficiency (SCE), which is defined as the fraction of photogenerated charge carriers at each point below the surface that contributes to the measured current. Analyzing SCE profiles at different operating potentials shows that increasing the applied potential primarily acts to reduce surface recombination rather than to increase the thickness of the space charge region under the semiconductor/electrolyte interface. Comparing SCE profiles obtained with and without a sacrificial reagent allows surface losses from electronically active defect states to be distinguished from performance bottlenecks arising from slow reaction kinetics. Combining these insights promotes a complete understanding of the photoanode performance and its potential as a water splitting photoanode. More generally, application of the SCE extraction method can aid in the discovery and evaluation of new materials for solar water splitting devices by providing mechanistic details underlying photocurrent generation and loss.