Search

A grid fusion lifting surface suitable for large subsonic angles of attack was designed. The influence of the grid position, grid diversion angle, and grid number on the aerodynamic performance of the grid fusion lifting surface under subsonic conditions was studied by numerical simulations. Based on the summary and analysis of the grid in the hypersonic state, the CFD numerical simulation method, which solves unsteady Reynolds averaged Navier-Stokes equations, was used to complete the research of the flow mechanism of the grid fin in the subsonic state. At low speed and subsonic conditions, the results show that the negative front grid fusion lift surface has better aerodynamic characteristics with a high angle of attack. Under subsonic conditions, the stall angle of attack of the front grid fusion lifting surface with a diversion angle of 20° increases by 16°, and the maximum lift coefficient increases by 22.1% compared to that of the conventional flat wing. The number of grids has an insignificant effect on the aerodynamic performance of the grid fusion lifting surface at a large angle of attack. [ABSTRACT FROM AUTHOR]

This study develops a novel neural-approximation-based prescribed performance controller for flexible hypersonic flight vehicles (HFVs). Firstly, a new prescribed performance mechanism is exploited, which develops new performance functions guaranteeing velocity and altitude tracking errors with small overshoots. Compared with the existing prescribed performance mechanism, it has better preselected transient and steady-state performance. Then, the nonaffine model of HFV is decomposed into a velocity subsystem and an altitude subsystem. A prescribed performance-based proportional-integral controller is designed in the velocity subsystem. In the altitude subsystem, the model is expressed as a nonaffine pure feedback form, and control inputs are derived from neural approximations. In order to reduce the amount of computation, only one neural network approximator is used to approximate the subsystem uncertainties, and an advanced regulation algorithm is applied to the devise adaptive law for neural estimation. At the same time, the complex design process of back-stepping can be avoided. Finally, numerical simulation results are presented to verify the efficiency of the design. [ABSTRACT FROM AUTHOR]

A computational-based investigation has been carried out to examine the heat transfer effects of normal and tangential blowing on blunt surfaces exposed to high Mach number flows. Experimental results from such studies where a controlled outflow is imposed upon a surface under hypersonic conditions are few and far between. Simple 3D axisymmetric configurations supporting flat front surfaces suited to accommodate uniform frontal flow or round-nosed conical bodies with a stepped shoulder to provide uniform parallel flow to the conical surface were selected from a NASA experiment for validation purposes. Uniform outflow of 0.55 to 1.0 kg/s was applied in the presence of the prevailing free stream of M=6.8 to assess the extent of heat transfer rate alleviation. The numerical simulation confirmed the experiment that the application of outflow in both cases leads to the surface heat transfer relief. [ABSTRACT FROM AUTHOR]

A novel flight control scheme is proposed using the terminal sliding mode technique, unidirectional auxiliary surfaces and the disturbance observer model. These proposed dynamic attitude control systems can improve control performance of hypersonic vehicles despite uncertainties and external disturbances. The terminal attractor is employed to improve the convergence rate associated with the critical damping characteristics problem noted in short-period motions of hypersonic vehicles. The proposed robust attitude control scheme uses a dynamic terminal sliding mode with unidirectional auxiliary surfaces. The nonlinear disturbance observer is designed to estimate system uncertainties and external disturbances. The output of the disturbance observer aids the robust adaptive control scheme and improves robust attitude control performance. Finally, simulation results are presented to illustrate the effectiveness of the proposed terminal sliding mode with unidirectional auxiliary surfaces. [ABSTRACT FROM AUTHOR]

This paper considers the numerical optimization of a double ramp scramjet inlet using magnetohydrodynamic (MHD) effects together with inlet ramp angle changes. The parameter being optimized is the mass capture at the throat of the inlet, such that spillage effects for less than design Mach numbers are reduced. The control parameters for the optimization include the MHD effects in conjunction with ramp angle changes. To enhance the MHD effects different ionization scenarios depending upon the alignment of the magnetic field are considered. The flow solution is based on the Advection Upstream Splitting Method (AUSM) that accounts for the MHD source terms as well. A numerical Broyden-Flecher-Goldfarb-Shanno- (BFGS-) based procedure is utilized to optimize the inlet mass capture. Numerical validation results compared to published results in the literature as well as the outcome of the optimization procedure are summarized to illustrate the efficacy of the approach. [ABSTRACT FROM AUTHOR]