Search

Potential earthquake-induced damage to overlapped tunnels probably occurs during the operation and maintenance of mountain tunnel engineering, especially in the seismically active zone. This study investigated the dynamic response and the failure characteristics of the parallel overlapped tunnel under seismic loadings by employing shaking table tests. The failure mode of the parallel overlapped tunnels was analyzed through macroscopic test phenomena. The dynamic responses of the surrounding rock and tunnel lining were evaluated by acceleration and dynamic strain, respectively. In particular, wavelet packets were used to investigate the spectrum characteristics of the tunnel structure in depth. The failure process of the model can be divided into three stages. The upper-span and the under-crossing tunnels showed different failure characteristics. Additionally, the lining damage on the outer surface of the tunnel mainly occurred on the right side arch waist and the left side wall, whereas the lining damage on the inner surface of the tunnel mainly appeared on the crown and invert. Wavelet packet energy results showed that the energy characteristic distributions of the upper-span and the under-crossing tunnels were not consistent. Specifically, the energy eigenvalues of the crown of the upper-span tunnel and the invert of the under-crossing tunnel were the largest, which should be considered to be the weak parts in the seismic design.

The existing conventional methods of subgrade disease assessment are not suitable for the existing lines. There are many research studies on the vibration response and attenuation law of the railway subgrade, but few research studies focus on the vibration response and attenuation law caused by the weak subgrade. In this study, vibration response tests were carried out at different positions and depths of the subgrade before and after reinforcement improvement. The results show that vibration response near the ballast is obvious, and it attenuates with the increase of the horizontal distance from the rail; the vibration acceleration response of the subgrade after reinforcement changes greatly; the vibration response curve of the reinforced section is spindle shaped, and the vertical vibration acceleration response attenuates obviously at the depth of 6.5 m, only about 10% to 30% of the surface; the vibration acceleration of the subgrade with reinforcement at the depth of 4.5 m attenuates to 60% of the surface; the vibration acceleration of the subgrade without reinforcement at the depth of 4.5 m attenuates to 50%–60% of the surface.

Affected by the site construction conditions, the measurement passes of the Taihang Expressway K8 + 105 ∼ K8 + 341 (K8 worksite) in the Taihang Expressway did not meet the requirements of data analysis, and the quantity of the control points was insufficient so that the linear correlation between the dynamic deformation modulus () and the vibratory compaction value (VCV) was not strong. Therefore, the target value of VCV cannot be used to diagnose the Ev d compaction quality of soil-rock filler. This paper analyzes the roller measurement VCV value and in situ measurements Ev d value separately. Results reveal the difference between the VCV mean measured in the last two passes and the standard deviation of the measured VCV mean in the last pass are used as the main basis for the actual compaction quality. In addition, the Ev d mean in the last rolling can be used as an auxiliary judgment basis for the quality control of the compaction.

With the steady development of the development of the western region in China, the construction of mountain highways has developed rapidly, and the soil-rock mixed filler, as an excellent filler, is widely used in the subgrade filling of mountain highways. Unlike ordinary fine-grained soil, the source of the soil-rock mixtures (S-RMs) is not unique, and the particle size difference is large and the water content is not uniform, resulting in very complicated mechanical properties. But the current highway embankment codes are still mainly established on the fine-grained soil. It is not fully applicable to soil-rock filled embankment. Based on soil-rock filled embankment engineering practice, this research uses a large-scale direct shear test to research the mechanical characteristics of the S-RMs with different maximum particle diameters. According to the large-scale direct shear test of S-RMs with different maximum particle diameters, the shear displacement vs shear stress curve, shear dilation, and strength characteristics with maximum particle diameter were analyzed. Results demonstrate that whether secondary hardening occurs mainly depends on the normal stress and the maximum particle diameter of the filler. At different maximum particle diameters, the horizontal displacement vs vertical displacement curves of the S-RMs can be roughly divided into continuous shearing and beginning of shearing and quick dilation. And the shear strength increases with the increase of the maximum particle diameter. Moreover, the cohesion decreases first and then increases with the increase of the maximum particle diameter, and the internal friction angle increases with the increase of the maximum particle diameter. Therefore, some RBs with large particle diameter added to filler can effectively improve the shear strength of the S-RMs, which may be valuable for realistic engineering.