Search

There is a global outcry over the speedy deterioration of structures in oil and gas facilities. While marine environment is considered the leading factor in the deterioration of offshore structures, there is no single factor considered as the main cause of the problem in onshore structures. Therefore, the aim of this paper is to present the result of global survey on the major factors causing the deterioration of concrete structures in onshore oil and gas facilities. To realize the objectives of the paper, an e-questionnaire was administered through two International LinkedIn groups with a membership mainly dominated by experts in onshore oil and gas facilities. 159 respondents completed the questionnaires, and the reliability of the responses was calculated to be 0.950 which is considered excellent. Relative importance index was used in ranking the factors, and it was observed that environmental factors ranked as the dominant factors causing the deterioration of concrete structures in onshore process plants. Another important finding in the study is the role that experience plays on the perception of experts on the causes of defects on concrete structures.

A flexural capacity model for fibre-reinforced concrete (FRC) beams reinforced with PVA and basalt fibres is suggested for the rectangular beam sections. The proposed models are based on the concept of equivalent stress block parameters for both compressive and tensile stresses, similar to Eurocode and ACI code. The parameters are defined by allowing the conversion of the stress-strain models into equivalent rectangular stress blocks, similar to Eurocode 2. The flexural model is suggested to determine the loading capacity of 21 FRC beams containing up to 3% volume fraction of PVA and basalt fibres without reinforcing bars. In order to investigate the accuracy of the proposed flexure models, finite element analysis (FEA) of the same beams was carried out using the compressive and tensile stress-strain curves. Furthermore, 21 FRC beams subjected to three-point bending were tested. The results of the flexural models showed good agreement with the load-carrying capacity of the tested FRC beams, and the results of FEA of all beams showed a good correlation with the experimental results in terms of the maximum load, load versus midspan deflection patterns, and the maximum tensile strains.

The mechanical properties of high-strength ductile concrete (HSDC) have been investigated using Metakaolin (MK) as the cement replacing material and PVA fibers. Total twenty-seven (27) mixes of concrete have been examined with varying content of MK and PVA fibers. It has been found that the coarser type PVA fibers provide strengths competitive to control or higher than control. Concrete with coarser type PVA fibers has also refined microstructure, but the microstructure has been undergone with the increase in aspect ratio of fibers. The microstructure of concrete with MK has also more refined and packing of material is much better with MK. PVA fibers not only give higher stiffness but also showed the deflection hardening response. Toughness Index of HSDC reflects the improvement in flexural toughness over the plain concrete and the maximum toughness indices have been observed with 10% MK and 2% volume fraction of PVA fibers.

This paper presents a review of the properties of fresh concrete including workability, heat of hydration, setting time, bleeding, and reactivity by using mineral admixtures fly ash (FA), silica fume (SF), ground granulated blast furnace slag (GGBS), metakaolin (MK), and rice husk ash (RHA). Comparison of normal and high-strength concrete in which cement has been partially supplemented by mineral admixture has been considered. It has been concluded that mineral admixtures may be categorized into two groups: chemically active mineral admixtures and microfiller mineral admixtures. Chemically active mineral admixtures decrease workability and setting time of concrete but increase the heat of hydration and reactivity. On the other hand, microfiller mineral admixtures increase workability and setting time of concrete but decrease the heat of hydration and reactivity. In general, small particle size and higher specific surface area of mineral admixture are favourable to produce highly dense and impermeable concrete; however, they cause low workability and demand more water which may be offset by adding effective superplasticizer.

This paper presents the mechanical properties and the microstructure of the high performance fiber reinforced concrete (HPFRC) containing up to 3% volume fraction of chopped Basalt fibers. Three types of the concrete were prepared, out of which, the first type was prepared by utilizing 100% cement content. The other two types of the concrete were prepared by replacing 10% cement content with silica fume and the locally produced metakaolin. Using each concrete type, four mixes were prepared in which Basalt fibers were added in the range of 0–3%; that is, total twelve mixes of the HPFRC concrete were prepared. From each of the twelve concrete mixes, total twelve specimens were cast to determine the mechanical properties of the HPFRC including compressive strength (cube and cylinder), splitting tensile strength, and the flexural strength. In this way, a total of 108 specimens were cast and tested in this study. Test results showed that the addition of the Basalt fibers significantly increased the tensile splitting strength and the flexural strength of the HPFRC, while there was slight improvement in the compressive strength with the addition of Basalt fibers. The microstructure of HPFRC was examined to determine the interfacial transition zone (ITZ) between the aggregates and the paste by using field emission scanning electron microscope (FESEM), which showed the improvement of the ITZ due to the addition of the Basalt fibers.