Search

Polyester based polymers are extensively used in aggressive marine environments; however, inadequate data is available on the effects of the seawater on the polyester based nanocomposites mechanical properties. This paper reports the effect of seawater absorption on the mechanical properties degradation of halloysite nanoclay-polyester nanocomposites. Results confirmed that the addition of halloysite nanoclay into polyester matrix was found to increase seawater uptake and reduce mechanical properties compared to monolithic polyester. The maximum decreases in microhardness, tensile and flexural properties, and impact toughness were observed in case of 1 wt% nanoclay. The microhardness decreased from 107 HV to 41.7 HV (61% decrease). Young’s modulus decreased from 0.6 GPa to 0.4 GPa (33% decrease). The flexural modulus decreased from 0.6 GPa to 0.34 GPa (43% decrease). The impact toughness dropped from 0.71 kJ/m2to 0.48 kJ/m2(32% decrease). Interestingly, the fracture toughnessKICincreased with the addition of halloysite nanoclay due to the plasticization effect of the resin matrix. SEM images revealed the significant reduction in mechanical properties in case of 1 wt% reinforcement which is attributed to the degradation of the nanoclay-matrix interface influenced by seawater absorption and agglomeration of halloysite nanoclay.

The use of graphene nanocomposites in advanced applications has attracted much attention in recent years. However, in order to substitute traditional epoxy reinforcements with graphene, there are still some issues like dispersion, homogenization, and reaggregation. In this paper, graphene bundles dispersed in two-component epoxy system by bath sonication, dispersion state, and reaggregation behavior of graphene in this system have been studied. Light transmittance in ultraviolet-visible spectroscopy has been used to quantify the reaggregation by a series of controlled experiments. After 18 mins sonication of 0.005 wt% graphene dispersion at 20°C, the light transmittance decreased from 68.92% to 54.88% in liquid epoxy and decreased from 72.80% to 46.42% in hardener; while increasing the temperature from 20°C to 60°C, the light transmittance in liquid epoxy decreased from 65.96% to 53.21% after 6 mins sonication. With the incorporation of 0.3 wt% graphene, the tensile strength of nanocomposites increased from 57.2 MPa to 64.4 MPa and the storage modulus increased from 1.66 GPa to 2.16 GPa. The results showed that the dispersion state depends on the function of sonication time and temperature, and graphene has a significant reinforcement effect on epoxy.

Amino-modified double wall carbon nanotube (DWCNT-NH2)/carbon fiber (CF)/epoxy hybrid micro-nanocomposite laminates were prepared by a resin infusion technique. DWCNT-NH2/epoxy nanocomposites and carbon fiber/epoxy microcomposites were made for comparison. Morphological analysis of the hybrid composites was performed using field emission scanning electron microscope. A good dispersion at low loadings of carbon nanotubes (CNTs) in epoxy matrix was achieved by a bath ultrasonication method. Mechanical characterization of the hybrid micro-nanocomposites manufactured by a resin infusion process included three-point bending, mode I interlaminar toughness, dynamic mechanical analysis, and drop-weight impact testing. The addition of small amounts of CNTs (0.025, 0.05, and 0.1 wt%) to epoxy resins for the fabrication of multiscale carbon fiber composites resulted in a maximum enhancement in flexural modulus by 35%, a 5% improvement in flexural strength, a 6% improvement in absorbed impact energy, and 23% decrease in the mode I interlaminar toughness. Hybridization of carbon fiber-reinforced epoxy using CNTs resulted in a reduction in and dampening characteristics, presumably as a result of the presence of micron-sized agglomerates.