Search

Due to rapid temperature rise and insulation moisture, bubbles can generate in the oil-paper insulation of oil-immersed power transformers, which can reduce the dielectric strength of oil-paper insulation and even bring about the risk of insulation breakdown. In order to accurately evaluate the conditions of bubble formation, the physical process of bubble formation in oil-paper insulation is studied in this article. Considering the effects of water vaporization, gas dissolution in oil, and moisture migration on bubble formation, a bubble formation prediction model is constructed. Based on Henry’s law, the dissolution equilibrium of gas in oil is taken into consideration and the upper boundary of the initial temperature of bubble effect (ITBE) envelope is obtained in this model. Based on the moisture equilibrium in oil-paper insulation, the bubble formation process caused by the emergence and rapid evaporation of free water is analyzed, and then, the lower boundary of the ITBE envelope is obtained in this model. The model results show that the moisture content of the pressboard and the presence of free water have a great impact on ITBE. Specifically, the higher the moisture content, the lower the ITBE value. In addition, with the further increase of moisture content, the upper and lower boundaries of the ITBE envelope gradually tend to be the same. However, once free water is present on the surface of cellulose, ITBE decreases rapidly to below 120 °C. The model built in this article is of great significance to study the temperature limit of the power transformer. Hence the ITBE envelope can provide an important theoretical reference for reducing the risk of bubble formation during power transformer operation. [ABSTRACT FROM AUTHOR]

The generation and distribution of furfural are significantly affected by moisture content in the insulating paper. However, the diffusion mechanism of furfural under moisture effect is not clear, hence, this study investigates the effect of moisture on the diffusion characteristics of furfural by combining macro experiment and micro molecular dynamics simulation. The simulation results demonstrate that the increased moisture content in paper accelerates the diffusion of furfural from paper to oil, which is also proved by the experimental data. Then, the results of interaction energy analysis indicate that the increase of moisture enhances the van der Waals force between oil and furfural. The present findings are expected to improve the theoretical level of furfural analysis, which will facilitate the aging evaluation of the transformer insulating paper based on furfural. [ABSTRACT FROM AUTHOR]

This article is aimed at quantifying the health condition of the power transformer insulation system through its frequency-domain dielectric characteristic by using the concept of the resistor and fractional calculus. In this regard, the dielectric model of the fractional Poynting–Thomson (PT) is proposed, and a mathematical model for parameter identification of the proposed model is presented. The shuffled frog leaping algorithm (SFLA) is used to realize the parameter identification and the fractional PT model parameters of the oil-paper samples under different insulation health conditions. The influence of moisture and aging on the fractional PT dielectric model parameters is experimentally studied. Results show that, with the increase in the water content within the insulation system, the parameters of the fractional PT model gradually decrease, and there is a strong correlation between the relaxation time and the water content. This facilitates the employment of the fractional PT model parameters to quantify the aging and moisture content of the power transformer insulation system. [ABSTRACT FROM AUTHOR]

Methanol concentration as an aging indicator can assess cellulose aging and estimate cellulose degree of polymerization (DP). Despite the advantages of methanol (MeOH), its major disadvantage is that its concentration in the oil decreases after some time. This point is called the MeOH peak in this article. Therefore, using this indicator when MeOH concentration is reduced leads to incorrect results. When using methanol, the main problem is that whenever the methanol concentration in a transformer is measured, it cannot be identified that the measured concentration belongs to the left or right side of the MeOH peak. If the measured concentration belongs to the right side of the MeOH peak, the estimated DP is incorrect. In this article, an empirical equation is established to estimate the DP value as a function of methanol concentration when methanol concentration belongs to the left side of the MeOH peak. Then, a new index called methanol peak detector index (MPDI) composed of a 2-furfural/MeOH ratio and normalized DP is presented to ensure the validity of the calculated DP value. If it is found that the measured concentration belongs to the left side of the MeOH peak, then the estimated DP by the presented equation is valid. Finally, the application of this method is verified by applying it to measurement data samples indicating the validity of the method. [ABSTRACT FROM AUTHOR]

The space charge effect of transformer insulating paper will distort its internal electric field, and its space charge effect will be more prominent under extremely complex working conditions. At present, the micromechanism of charge transport and electric field distortion characteristics of paperboard are not clear under complex working conditions. So in this article, based on the bipolar carrier transport (BCT) model and the dynamic carrier balance model, the effects of high temperature, aging degree, moisture content, and bent degree on charges accumulation in paperboard are studied under dc high voltage by numerical simulation and the measured data needed for simulation. The results show that the higher temperature strengthens the carrier migration, deepens the injection depth of the charge, and aggravates the distortion of electric field intensity in paperboard. The more extended the aging time of paperboard, the greater the internal trap density and the deeper the trap depth, which lead to charges migration difficultly. Increasing water content in the paperboard will accelerate space charges to reach a steady state, while further increasing it will slow down this process, which is related to the shallow trap getting deeper. When the critical part of paperboard is extruded, many traps are introduced, resulting in charges accumulation seriously. The research results can reference the design of paperboard and the maintenance of transformer insulation system. [ABSTRACT FROM AUTHOR]

The traditional method for transformer moisture diagnosis is to establish empirical equations between feature parameters extracted from frequency domain spectroscopy (FDS) and the transformer’s moisture content. However, the established empirical equation may not be applicable to a novel testing environment, resulting in an unreliable evaluation result. In this regard, it is acknowledged that FDS combined with machine learning is more suitable for estimating moisture content in a variety of test environments. Nonetheless, the accuracy of the estimation results obtained using the existing method is limited by the algorithm’s inability to generalize. To address this issue, we propose an AdaBoost algorithm-enhanced back-propagation neural network (BP_AdaBoost). This study creates a database by extracting feature parameters from the FDS that characterize the insulation states of the prepared samples. Then, using the BP_AdaBoost algorithm and the newly constructed database, the moisture estimation models are trained. Finally, the results of the estimation are discussed in terms of laboratory and field transformers. By comparing the proposed BP_AdaBoost algorithm to other intelligence algorithms, it is demonstrated that it not only performs better in generalization, but also maintains a high level of accuracy. [ABSTRACT FROM AUTHOR]

Video halftoning is a key technology for use in electronic paper (e-paper) or smart paper, which is an emerging display device that has received considerable attention recently. In this paper, a temporal frequency of flickering-distortion optimized video halftoning method is proposed. We first uncover three visual defects that conventional neighboring frame referencing-based video halftoning methods, due to their sequential changes of reference frames, will encounter. To deal with the problem, we then propose a reference frame update per GOP-based error diffusion video halftoning method based on a flickering sensitivity-based human visual model. To efficiently compromise between average temporal frequency of flickering (ATFoF) and visual quality, temporal frequency of flickering-distortion (TFoFD) is presented as a metric for video halftoning performance evaluation. Based on the proposed probability model of video halftoning, the TFoFD curve can be accurately estimated to optimize the tradeoff between quality and ATFoF before the video is halftoned. Our temporal frequency of flickering-distortion optimization strategy can also be applied to other video halftoning schemes for performance improvement. Experimental results and comparisons with known methods demonstrate the effectiveness of our video halftoning method. [ABSTRACT FROM PUBLISHER]

The service life of a transformer is determined by the condition of its oil?paper insulation. A modified Cole?Cole model was introduced to describe the frequency domain spectroscopy (FDS) curves based on the classic Debye relaxation model and thereby accurately determined the ageing state of the insulation of a power transformer using FDS. Oil?paper insulation samples with different ageing states are prepared under laboratory conditions, and a characteristic parameter is extracted to quantify their ageing states after a detailed investigation of the frequency domain dielectric properties of the samples. Results reveal that the modified Cole?Cole model, including the ? relaxation components, dc and hopping conductivity components, can be employed to effectively model the frequency dielectric characteristics of oil?paper insulation. Furthermore, the extracted characteristic parameter from this model, ??, can be utilized in the quantitative evaluation of the ageing states of transformer insulation. A case example is discussed to demonstrate the applicability of the proposed technique in the condition assessment of field power transformers. [ABSTRACT FROM AUTHOR]

Samples of a dried composite oil-paper system were thermally aged in the laboratory under N2 in a sealed container and analysed using their dielectric response. The contributing loss processes were separated using an equivalent circuit model containing constant high frequency capacitances, dc-conductances, a dispersive capacitance, and a low frequency quasi-dc (q-dc) dispersion process as circuit elements. This low frequency dispersion in oil-paper samples is a bulk property of the system that is often mistaken for a dc conduction process when only the imaginary capacitance or ac-conductance is measured. The Dissado-Hill response function is proposed for the frequency dependence of the dispersive capacitance in the mid-frequency range rather than the Debye function because its cluster concepts correlate with the sample morphology of a matrix of oil-filled cavities. The quasi-dc dispersion is assigned to the transport of mobile charges between charge-clusters associated with locally connected oil filled cavities, which is a process that can be represented on a global scale by the form of hierarchical circuit system that leads to constant phase angle responses, and is here modelled by the Dissado-Hill q-dc function. It was found that the two dispersions moved together to higher frequency with thermal ageing of the composite material. The characteristic frequency common to the dispersions had an activation energy that decreased with thermal ageing, whereas their amplitude increased. This behavior is discussed in terms of possible changes to the oil-paper composite caused by the ageing process. [ABSTRACT FROM AUTHOR]

Recently, there has been a lot of success in using the deterministic approach to provide approximate characterization of Gaussian network capacity. In this paper, we take a deterministic view and revisit the problem of wiretap channel with side information. A precise characterization of the secrecy capacity is obtained for a linear deterministic model, which naturally suggests a coding scheme which we show to achieve the secrecy capacity of the degraded Gaussian model (dubbed as “secret writing on dirty paper”) to within half a bit. [ABSTRACT FROM PUBLISHER]

A substantial quantity of testing has been performed on the degradation of paper insulation over the decades. The aim being to better educate the electrical industry on how to best operate expensive assets, such as transformers. The longevity of paper insulation is frequently tested using accelerated ageing experiments, where the effects of temperature and the chemical environment on paper lifespan can be studied. Such research has resulted in paper life expectancy curves being published by the IEEE and the IEC. The investigations tend to use sealed vessels. However, the disadvantage of using this method is that the water content of the paper changes during the ageing process which then changes the ageing rate. In these ageing experiments the water and oxygen content was controlled using a special test rig to compare the ageing rate to previous work and to determine the ageing effect of paper by combining temperature, water content of paper and oxygen content of the oil. We found that the rate of paper ageing can be more accurately determined by controlling the water and oxygen during the experiment which then produced noticeable changes in predicting life expectancy. [ABSTRACT FROM PUBLISHER]

Dielectric parameters of insulation used in High voltage equipments like power transformers are dependent on insulation size and geometry. As a result parameters evaluated from the model of one insulation system finds limited use in predicting the condition of other. Poles calculated from branch parameters of insulation model, on the other hand are independent of insulation geometry. However such technique requires accurate modeling of dielectric response function. Conventional Debye model does not consider the effect of temperature gradient that exists across the length of the insulation during its operation. In the present paper it is shown that for more accurate modeling and better understanding of dielectric response of oil-paper insulation, a new model which considers the effect of temperature gradient on insulation properties, is necessary. The present paper reports a methodology that is capable of identifying such a model using PDC measurement data. It is also shown that use of conventional Debye model overestimates the pole values and the error increases with usage of the insulation. [ABSTRACT FROM AUTHOR]

This paper presents and verifies a new mathematical model to explain the dynamic behavior of characteristic gases in the oil-cellulose insulation of high voltage devices like power transformers. The model is based on the diffusion process. Parameters of the model are already quantified from experiments and presented in previous publications. The mathematical model and assumptions are presented here. The model solution is obtained analytically and gas concentration change inside the paper insulation as a function of time is simulated. The results are converted to the concentration change in the oil using the principle of conservation of mass and validated with experimental measurements. The presented model can be used to reduce the error of Dissolved Gas Analysis due to the migration of characteristic gases inside a healthy power transformer. [ABSTRACT FROM AUTHOR]

This paper deals with the problem of moisture in the transformer insulation system. The author proposed that apart from the temperature, the uneven aging of cellulose insulation may have a substantial effect on moisture distribution. The main goal of the research was to check the influence of the degree of aging of winding paper on moisture distribution by taking into account temperature distribution. New paper and paper at three different stages of aging were tested. The obtained results confirmed the hypothesis it was proven that the uneven aging of insulation may enhance moisture distribution in the insulation system. [ABSTRACT FROM PUBLISHER]

This paper elucidates the question whether bubble effect can possibly take place in the insulation of OIP (Oil Impregnated Paper) type of bushings. The investigations were performed on a bushing insulation model and indicated to a possibility that the effect may occur. Presence of metallic screens in the insulation does not limit the development of gas bubbling; they only force the motion of water vapor bubbles along the model axis. The temperature dependence of bubble initiation on the water content in paper part of the bushing insulation is similar to the presented earlier in literature characteristics for bubbling in main insulation of power transformers. The possibility of bubble effect occurrence may explain the relatively frequent cases of transformer bushing failures. [ABSTRACT FROM PUBLISHER]

In order to complete the broadband simulation model of power transformer, and establish a systematic and complete model for studying fast transient interaction between transformer and power system, the frequency dependent characteristics of dielectric losses in power transformer were investigated. Several typical insulation structures in power transformers were considered and measuring techniques determined to study the dielectric losses. Frequency dependent dielectric losses in the range of 10-107 Hz were measured by a dielectric spectroscopy analyzer produced by Novocontrol. The characteristics of insulating papers and pressboard measured in the air and after immersing in the mineral oil were compared. Based on the dielectric relaxation theory, the number of dielectric relaxation was determined according to the measured data, and four typical model functions were adopted to fit the data and the consistency of fitting by these functions were compared and physical explanations of fitting parameters were described. Finally, a quantitative description of frequency dependent characteristics of insulation losses was proposed for improving the transformer simulation model. [ABSTRACT FROM PUBLISHER]

This paper proposes a new method to improve re performance of intra-field interpolation which is the mos~ important element of deinterlacing method. Traditional edge- based methods were poor at determining accurate edge iirection which decides interpolation performance. The 7roposed method decides the direction and slope of edge based on locally adaptive-thresholded binary image to mprove efficiency and accuracy, and it also increased the ~orizontal size of search window to 15 for better direction ietermination at gentle slope. Compared to traditional edge- based methods, interpolation based on binary image, which is ,`enerated using the proposed method, leads to great erformance improvement. With computer simulations for a ~`ariety of images, this paper shows the new approach is much ~etter than traditional methods.. [ABSTRACT FROM AUTHOR]

This paper proposes a way to represent the anisotropic nonlinear superconducting properties using a discrete model for magnetization with the corresponding critical parameters, equivalent to the Power Law model for currents. This simplified model makes it possible to analyze magnetic systems with superconducting elements in a stationary mode, which reduces the calculation time. Using of proposed model is demonstrated by the calculation of force interactions between high-temperature superconducting (HTS) samples and permanent magnet in zero-field-cooling (ZFC) and field-cooling (FC) modes. HTS bulks in the form of a prism and stack made of HTS tape are considered. The calculation of the electromagnetic field was carried out using the method of integral equations for field sources. The data of calculations are compared with the results of experimental studies. [ABSTRACT FROM AUTHOR]

This paper presents an implementation of an ~daptive beamformer in a hands-free unit. The proposec~ ~daptive beamformer suppresses stationary noise an~ nterference sound. The adaptive beamformer and acoustic `cho canceller were implemented in a compact hands-free mit with a low-cost DSP. Experimental results demonstrate he noise reduction performance of the hands-free unit'. [ABSTRACT FROM AUTHOR]

The simulation of electric field transients in HVDC cables can be a fundamental tool to support insulation system design when operation dynamics, which includes voltage polarity inversions and load variation, becomes significant during the expected cable life. The field behavior during voltage and temperature transients is associated with intrinsic and extrinsic ageing processes that can affect the cable design life. Traditional models employed for electric field simulations consider only the non–linear, steady–state dependence of conductivity on temperature and field magnitude, but they neglect the transient behavior of permittivity and conductivity, that is, polarization and charge trapping phenomena. These processes impact on the duration of the field transient and thus ageing. This paper discusses the numerical implementation of an electro–quasistatic model that can be used to perform transient simulations of electric fields in HVDC cables insulation. With respect to the model traditionally employed, the presented one is extended with Debye's equations for dielectric polarization processes. The model is implemented numerically using finite differences, or the Occhini equivalent circuit: this paper demonstrates that the two approaches are equivalent. Numerical simulations show that, during transients, polarization processes slow down the electric field dynamics and reduce its maximum intensity. [ABSTRACT FROM AUTHOR]

Fast and accurate power-flow methods are of great importance, especially in near real-time optimal operation of power systems. This importance will be even more highlighted in the presence of more repetitions of power-flow calculations, which cause more computational complexities in optimization problems. As a solution, in this paper, a novel fast and accurate approach of linear power-flow formulation is proposed. Principles of the proposed approach are based on dividing power-flow calculations into base and variable parts. To this aim, at first, system modeling of base and variable parts are presented. For the base-part modeling, utilizing a nonlinear power-flow, an accurate base power-flow (BPF) is extracted. Afterwards, by linearizing the power system around the BPF, variable-part model which is the result of a linear fitting process, is obtained. Then, it is shown that the variable-part of the operating point is always a function of the obtained base-part and variable-part models. In this paper, by focusing on the stochastic application of the proposed approach, different uncertainties in a distribution system are considered. Finally, numerical results carried out in the Matlab environment, for a IEEE 34-bus standard distribution system and then a 1486-bus case study, verify the performance of the proposed approach. [ABSTRACT FROM AUTHOR]

As is known, cable plays a significant role in electric power transmission of the ship. From the safety perspective, this paper aims to predict the ship cable life more accurately and analyze its reliability under small sample conditions. To achieve this goal, based on the non-equidistant grey model (NEGM (1, 1)), an optimized equal-dimension dynamic NEGM (1, 1) is proposed in this paper. In the improved model, the raw data smoothness and the background value are optimized to apply to grey model parameters. Equal-dimension dynamic prediction algorithm (EDDPA) is adopted to predict the lifetime of ship CXF type cable. Compared with the aging model from literature and NEGM (1, 1), the prediction effectiveness and reliability of the proposed model are more considerable. Interestingly, with the increase of recurrence times, the numerical results show this model has higher prediction performance. Finally, the reliability and confidence interval of the life evaluation of ship CXF cable are given to provide more valuable information for the cable management. [ABSTRACT FROM AUTHOR]

This paper is devoted to electric arc furnace (EAF) modeling using a random differential equation based on the power balance equation. The proposed approach broadens and improves the model through the introduction of stochastic processes in place of existing coefficients. The paper presents a method which enables the estimation of EAF model coefficients with the help of measurement data - voltage and current waveforms recorded during the melting stage of an EAF work cycle. The estimation process is conducted with a Monte Carlo method and genetic algorithm, which is applied iteratively to each of the defined frames of the input signal. The estimated coefficients have been analyzed with respect to their time variability as well as the probability distributions of their values and increments. The results have been extensively visualized. Next, the identification of the stochastic processes representing the model coefficients has been carried out. Based on the previous results and autocorrelation functions, the density functions and parameters of discrete-time stochastic processes were identified. The paper presents solutions validated with statistical tests. [ABSTRACT FROM AUTHOR]

The opening up of the railway to competition in Europe has been accompanied by many technical challenges never before seen in the railway field. One of these challenges concerns precise energy metering. As European railways have been a monopoly until now, the current systems can only measure the energy consumption of a single operator. In accordance with European law, the installation of an energy meter has been mandatory in new or refurbished rolling stocks since 2014. Nevertheless, these energy meters are still not fully reliable, with misreadings and missing readings being common occurrences. To address the problem of energy metering data reliability, this paper presents a method for validating the reading measurement based on a physical model and validates it in two different case studies. For the issue of energy metering data availability, different estimators are developed, and their performance are shown with the aim of calculating the missing consumptions for both case studies. Finally, the paper suggests how these methods may be implemented in other types of trains. [ABSTRACT FROM AUTHOR]

This paper presents an approach for the time domain statistical simulation of field-to-wire coupling model with uncertain wire position in traverse direction. The parameters of governing equations of field-to-wire coupling model about the wire position are expanded to the augmented governing equations by using the generalized polynomial chaos technique with normalized orthogonal basis functions. And the coefficients of the polynomial chaos expansions are solved by combining with the stochastic Galerkin method. However, the solution of augmented governing equations is a complex problem. Therefore, a new finite-difference time-domain (FDTD) algorithm based on the implicit Wendroff difference format is proposed to solve the governing equations, and the general iterative equations are given in this paper. The proposed methods are verified by a field-to-wire coupling model. The effectiveness and advantages of the new FDTD algorithm and the uncertainty analysis method based on generalized polynomial chaos technique are verified, which are achieved by comparing with the conventional leapfrog fashion FDTD algorithm and the Monte Carlo technique, respectively. [ABSTRACT FROM AUTHOR]

Electric distribution grid operations typically rely on both centralized optimization and local non-optimal control techniques. As an alternative, distribution system operational practices can consider distributed optimization techniques that leverage communications among various neighboring agents to achieve optimal operation. With the rapidly increasing integration of distributed energy resources (DERs), distributed optimization algorithms are growing in importance due to their potential advantages in scalability, flexibility, privacy, and robustness relative to centralized optimization. Implementation of distributed optimization offers multiple challenges and also opportunities. This paper provides a comprehensive review of the recent advancements in distributed optimization for electric distribution systems and classifications using key attributes. Problem formulations and distributed optimization algorithms are provided for example use cases, including volt/var control, market clearing process, loss minimization, and conservation voltage reduction. Finally, this paper also presents future research needs for the applicability of distributed optimization algorithms in the distribution system. [ABSTRACT FROM AUTHOR]

Factor graph optimization (FGO) is a well-known approach in the robotics field. Due to multiple iterations and application of large amounts of data, it usually could superior performance than the Kalman Filter (KF) under complex scenarios. However, it is rarely used in the underwater environment, especially for applications based on fiber-optic inertial navigation. Taking the ultra-short baseline system (USBL) as the application background, a novel inertial navigation system (INS)/USBL integrated navigation scheme based on FGO is presented in this paper. The traditional pre-integration factor simplifies the earth rotation and coordinate system, which limits its application in high-precision sensors. This paper proposed an improved pre-integration model using the high precision measurements of fiber optics gyroscope in FGO. Simulation and field tests proved that, with the FGO method, improved accuracy of INS/USBL integration was obtained compared to the traditional KF method. It confirms the potential of FGO in the applications of underwater navigation and positioning. [ABSTRACT FROM AUTHOR]

It is known that there exist mathematical problems of practical relevance which cannot be computed on a Turing machine. An important example is the calculation of the first derivative of continuously differentiable functions. This paper precisely classifies the non-computability of the first derivative, and of the maximum-norm of the first derivative in the Zheng-Weihrauch hierarchy. Based on this classification, the paper investigates whether it is possible that a Turing machine detects this non-computability of the first derivative by observing the data of the problem, and whether it is possible to detect upper bounds for the peak value of the first derivative of continuously differentiable functions. So from a practical point of view, the question is whether it is possible to implement an exit-flag functionality for observing non-computability of the first derivative. This paper even studies two different types of exit-flag functionality. A strong one, where the Turing machine always has to stop, and a weak one, where the Turing machine stops if and only if the input lies within the corresponding set of interest. It will be shown that non-computability of the first derivative is not detectable by a Turing machine for two concrete examples, namely for the problem of computing the input–output behavior of simple analog circuits and for solutions of the three-dimensional wave equation. In addition, it is shown that it is even impossible to detect an upper bound for the maximum norm of the first derivative. In particular, it is shown that all three problems are not even semidecidable. Finally, we briefly discuss implications of these results for analog and quantum computing. [ABSTRACT FROM AUTHOR]

The paper addresses a real-time optimization-based reference calculation integrated with a control structure for Modular Multilevel Converters (MMC) operating under normal and constrained situations (where it has reached current and/or voltage limitations, as it may occur during system faults). Firstly, a nonlinear optimization problem has been developed in which it prioritizes to satisfy the AC grid current set-points imposed by the transmission System Operator (TSO). The constrained nonlinear optimization problem is formulated based on the steady-state model of the MMC, whereby the prioritization is achieved through distinct weights defined in the Objective Function’s (OF) terms. The resultant optimization problem, however, is highly nonlinear requiring high computation burden to be solved in real-time. To cope with this issue, this paper applies a Linear Time-Varying (LTV) approximation, which permits to represent the nonlinear dynamics of the system as constant parameters, while a Linear Time-Invariant (LTI) system is used to formulate the optimization constraints. The converter’s current references are determined in real-time by solving a constrained linearized optimization problem at each control time step, which considers the TSO’s demands, the current MMC operating point and its physical limitations. Theoretical analyses comparing the responses of the linear and nonlinear optimization problems are performed to validate the accuracy of the LTV approximation. Finally, the linearized-optimization problem is integrated with the MMC controllers, evaluated under different AC and DC network conditions and compared with conventional control strategies, where it is shown that the presented method can be potentially employed to obtain the MMC current references for distinct network scenarios. [ABSTRACT FROM AUTHOR]

The paper presents an experimental validation of a method to locate partial discharges (PDs) on power distribution and transmission networks. The method is based on electromagnetic time reversal (EMTR) theory, and it uses a Transmission Line Matrix (TLM) model to describe the propagation of the PD signals in the reversed time. Since PDs are regarded as a symptom of insulation degradation, on-line PD location is considered an important approach to monitoring the integrity of a power distribution network, with the aim of detecting and preventing faults and improving network reliability. In this paper, the EMTR-based method is described and its effectiveness in PD localization using only one measurement point is demonstrated in three real 33 kV power lines. Its effectiveness is proved with and without an on-line electromagnetically noisy environment, and its accuracy is evaluated with respect to different signal-to-noise ratio (SNR) levels of the networks. The validation shows that the method is able to locate PDs with an error of 0.14% with respect to the total length of the line in the absence of noise, and with an error that is always lower than 0.5% for an SNR down to −7 dB. [ABSTRACT FROM AUTHOR]

A good quality stability model is a key factor for accurate power system operations.Inaccurate parameters of the stability models affect the decision making which paves the way for serious consequences. Thus, it is necessary to calibrate the stability model parameters in a regular manner. There are several calibration methods in the literature which are based on simultaneous estimation of the parameters and states. However, not all of the model parameters are well estimable simultaneously. Simultaneous estimation of parameters with high collinearity may result in biased calibration results. In this paper, the trajectory sensitivity method is used to detect the sensitive parameters and construct the sensitivity matrix. Then, parameters with high linear dependency are identified using the sensitivity matrix. It is shown that, despite the high sensitivity of a parameter, its estimability degrades as the collinearity with other parameters increase. In this paper an identifiability analysis that detects the collinearity among the sensitive parameters is proposed. The proposed method is validated using WSCC 9-Bus System. [ABSTRACT FROM AUTHOR]

Distribution power systems (DPSs) are generally unbalanced, and their loads may have notable static voltage characteristics (ZIP loads). Hence, although many papers have focused on linear single-phase power flow models, it is still necessary to study linear three-phase distribution power flow models. This paper proposes a data-driven-aided linear three-phase power flow model for DPSs. We first formulate how to amalgamate data-driven techniques into a linear power flow equation to establish our linear model. This amalgamation makes our linear model independent of the assumptions commonly used in the literature (e.g., nodal voltages are nearly 1.0 p.u.); therefore, our model is characterized by relatively high accuracy, even when the assumptions become invalid. We then demonstrate how to apply our model to DPSs with ZIP loads. We also show that with the Huber penalty function employed, the adverse impact of bad data on our model's accuracy is significantly reduced, rendering our model robust to poor data quality. Case studies demonstrate that our model is generally more accurate, with 2- to 100-fold smaller errors, than most existing linear models, and remains fairly accurate even under poor data conditions. Our model also contributes to a rapid solution to DPS analyses and optimization problems. [ABSTRACT FROM AUTHOR]

Superdirective arrays have been extensively studied because of their considerable potential accompanied, unfortunately, by a high sensitivity to random errors that affect the responses and positions of array elements. However, the statistics of their actual beam pattern (BP) has never been systematically investigated. This paper shows that the Rician probability density function (PDF), sometimes adopted to study the impact of errors in conventional arrays, is a valid approximation for superdirective BP statistics only where some mathematical terms are negligible. The paper also shows that this is the case for all linear end-fire arrays considered. A similar study is proposed concerning the correlation between BP lobes, showing that for the superdirective arrays considered the lobes, especially non-adjacent ones, are almost independent. Furthermore, knowledge of the PDF of the actual BP allows one to define quantile BP functions, whose probability of being exceeded, at any point, is fixed. Combining the lobes’ independence with quantile BP functions, an empirical equation for the probability that the entire actual BP will not exceed a quantile function over an interval larger than a given size is obtained. This new knowledge and these tools make it possible to devise new methods to design robust superdirective arrays via optimization goals with clearer and more relevant statistical meaning. [ABSTRACT FROM AUTHOR]