Search

In the conventional sliding mode control, the four-leg distribution static compensator (DSTATCOM) currents are controlled based on a current error in each phase. However, the four currents in a four-wire system can not be independently controlled variables and hence one of the four controllers is redundant in conventional schemes. Further, the current dynamics of a DSTATCOM converter are coupled through converter pole voltages in the natural reference frame. This leads to cross-coupling in the sliding variable equations with respect to four manipulated input variables. Considering the above points, in this paper, the current due to Thevenin’s equivalent load neutral-point voltage is considered as a fourth independent controlled variable and the corresponding system dynamic equations are presented. To get a decoupled feature, a new sliding surface function is structured. The performance of a DSTATCOM with the proposed control scheme under various operating conditions is validated through a detailed simulation study and experimental results, obtained from a laboratory prototype of four-leg DSTATCOM. [ABSTRACT FROM AUTHOR]

This paper proposes an improved performance interactive distribution static compensator (DSTATCOM) to address the limitations of conventional current control mode (CCM) and voltage control mode (VCM) operations. The proposed interactive scheme provides smooth transfer of modes of operation while remaining connected in the distribution system. In normal operation, the DSTATCOM operates in CCM to make source currents balanced, sinusoidal, and at a unity power factor. During voltage disturbances, the CCM operation cannot improve load voltage. In that case, DSTATCOM operation is changed to VCM, which maintains a constant voltage across the sensitive loads. Hence, this interactive DSTATCOM ensures continuous, flexible, and robust operation of the load. Moreover, the filter current requirements are reduced in the proposed scheme, which reduces the losses in the filter and feeder, improves inverter efficiency, and requires a reduced-rating inverter for sag mitigation. The principle of operation and control for both operating modes is analyzed. The detailed process of the flexible transfer between the two modes is derived. Deadbeat predictive control algorithms for CCM as well as VCM operation are developed for fast operation during mode transfers. The performance of the proposed scheme is validated by both simulation and experimental results. [ABSTRACT FROM PUBLISHER]

Dynamic voltage restorer (DVR) is a definitive solution toward compensation of voltage sag with phase jump. Conventional DVR topologies, however, have dc links and two-stage power conversions. This increases its size, cost, and associated losses. Therefore, topologies without the dc link, mitigating sag by utilizing direct ac–ac converters, are preferable over the conventional ones. As no storage device is employed, compensation by these topologies is limited only by the voltages at the point of common coupling that is feeding the converters. In this paper, a direct-ac–ac-converter-based topology fed with line voltages is proposed. The arrangement provides increased range of compensation in terms of magnitude and phase angle correction. Detailed simulations have been carried out in MATLAB to compare the capability of the proposed topology with other similar topologies. Experimental results are presented to validate the capability of the topology to compensate various sags. [ABSTRACT FROM PUBLISHER]

Loads connected to a stiff source cannot be protected from voltage disturbances using a distribution static compensator (DSTATCOM). In this paper, a new control-algorithm-based multifunctional DSTATCOM is proposed to operate in voltage control mode under stiff source. This scheme provides fast voltage regulation at the load terminal during voltage disturbances and protects critical loads. In addition, during normal operation, the generated reference load voltages allow control of the source currents. Consequently, DSTATCOM injects reactive and harmonic components of load currents to make source power factor unity. Simulation and experimental results are presented to verify the efficacy of the proposed control algorithm and multifunctional DSTATCOM. [ABSTRACT FROM PUBLISHER]

The unified power-quality conditioner (UPQC) is used to provide balanced and sinusoidal source currents and load voltages under unbalanced and distorted three-phase supply voltages and load currents in a power distribution network. In this paper, a particle swarm optimization-based feedback controller is designed for UPQC. This feedback controller has optimal performance in various operating conditions and is robust to parametric uncertainties when compared to the conventional feedback controllers, such as the linear quadratic regulator. The proposed method is implemented on a distribution system and detailed simulation and experimental results are presented. [ABSTRACT FROM PUBLISHER]