Search

A polypropylene (PP) film is usually employed as the main insulation of the peaking capacitor, which is important in an electromagnetic pulse simulator to generate high-amplitude nanosecond pulse. The flashover voltage of PP films under nanosecond pulse limits the highest working voltage of a peaking capacitor. Surface fluorination was employed to increase the flashover voltage of PP. The flashover voltages of PP samples with different fluorination times (0, 4, and 6 h) were tested in an oven with nanosecond pulse voltage. The results showed that the flashover voltage of the PP film with 6-h surface fluorination was increased about 15% than the untreated film in the air. To clarify the influential mechanism, the physicochemical properties of PP film samples were tested and characterized. The results of thermally stimulated depolarization current (TSDC) showed that the trap density of the PP film increased obviously after fluorination treatment. With the increase in treatment time, the trap depth and density were increased obviously. The surface conductivity of PP films slightly decreased with the increase in fluorination time. The mechanism of surface fluorination on the influence of the flashover performance of the PP film under nanosecond pulse is discussed. It is concluded that surface fluorination significantly increases the carbon–fluorine (C–F) bond of the PP film, resulting in the increase in the depth and density of the surface trap, and then, a large amount of homocharges trapped in the surface trap reduces the electric field near the electrode. [ABSTRACT FROM AUTHOR]

Numerical simulation of discharge mechanism under nanosecond pulse voltage assists in the insulation performance optimization of N2-insulated switches that are widely used in the pulse power devices. This article presents a fluid dynamic model for the positive streamer propagation in N2 based on a needle-plate discharge system. The effects of the operating conditions, such as voltage amplitude, rising edge, gap width, and needle radius, are studied. Simulating results indicate that the streamer might be evoked only when the maximum electric field exceeds the critical value that is closely influenced by the needle radius and gap width, e.g., $1.3\times 10^{7}$ V/m based on a needle-to-plate electrode configuration with a 0.4-mm tip radius and 5-mm gap. The maximum electric field occurs at the head of streamer and it drops suddenly by nearly two orders of magnitude in the back of the head, which makes the streamer moves forward rapidly. Certainly, it needs a high enough voltage to ensure continuous propagation of the streamer, for example, more than 20 kV needed as the tip radius and gap set to 0.4 and 5 mm, and the electric field strength and migration speed increase with the increasing voltage amplitude. The radius of the discharge region is smaller when the rising edge time increases from 10 to 40 ns. However, if the rising edge time is too low (e.g., 2 ns), the streamer will cease before it propagates to the plate electrode and the radius of the discharge region shrink at the same time. In addition, the peak electric field and the averaged electron energy at the same position away from the needle decrease slightly with the gap width. Finally, there is an obvious decrease of the initial peak electric field as the needle radius increases. [ABSTRACT FROM AUTHOR]

The polymer film dielectric has been widely used in high voltage equipment for bulk insulation owing to the excellent insulation performance. Martin’s empirical formula for bulk breakdown is frequently used to predict the breakdown field strength of multilayer thin film with different electrode areas. In this article, based on the academic consensus that the cumulative breakdown probability of single-layer film obeys the Weibull distribution, the relationship between the cumulative breakdown probability of film dielectric under different electrode areas and the applied electrical field is deduced. Moreover, the relationship between the cumulative breakdown probability of film dielectric with various numbers of film layers and the applied electrical field is obtained and simplified. On these bases, combined with the experimental results of the average breakdown field of film dielectric with smaller electrode areas and fewer layers, a prediction model of the average breakdown field strength of film dielectric with different electrode areas and film layers is established. To obtain the solution of the prediction model concerning the number of film layer, an effective approximate solution method is proposed to solve the calculation problem with ultralarge and ultrasmall data, which significantly reduces the complexity of the solution process. A coaxial film capacitor is developed and tested to verify the prediction model with the “Chenguang” accelerator. The experimental breakdown field strength of 54 layers of 15 $\mu \text{m}$ biaxially oriented polypropylene (BOPP) film with an electrode area of 218.1 cm2 is 355.6 V/ $\mu \text{m}$ , which is comparable to the predicted result of 374 V/ $\mu \text{m}$. The prediction model presented in this article is of certain reference significance for the insulation design of film dielectrics. [ABSTRACT FROM AUTHOR]

In the practical operation of an electromagnetic pulse (EMP) simulator, the flashover phenomenon on the edge of polypropylene dielectrics dominates the insulation failure mode of a peaking capacitor. To analyze the characteristics of polypropylene film flashover voltage under high-pressure SF6, an experimental platform was established, and the pulse generator could output a pulse with a rise time of approximately 27 ns. The experiments were performed on finger electrodes, and the SF6 pressure was set from 0.1 to 1.0 MPa. The experimental results show that the relationship of flashover voltage and gas pressure could be divided into two regions: in low-pressure regions, the flashover voltage increases with the gas pressure linearly and in high-pressure regions, the growth of flashover voltage gradually slows down and approaches a saturation value. As the gap distance increases, the saturation point of gas pressure decreases, and even when close to 0.4 MPa, with a 9-mm gap distance, this unconventional phenomenon cannot be ignored, particularly in practical EMP simulators. When the high surface resistivity and the charge trap distribution on the polypropylene film are considered, the accumulation and emission of surface charges on the film might be the primary reason for the saturated phenomena. [ABSTRACT FROM AUTHOR]

Due to its low-loss and high dielectric strength, polypropylene is widely used as electrical insulation material in pulse capacitors. In order to study its breakdown characteristics for nanosecond voltage pulses, an experimental setup was designed to generate voltage pulses with a 10%–90% rise time of 38 ns and a full width at half maximum of about 90 ns. Tests of the three polypropylene films with thicknesses of 12, 15, and $18~\mu \text{m}$ were performed. In addition, hundreds of nanoseconds pulse and dc voltage were also applied for comparison. The experimental results reveal that most of the breakdown occurs during the front edge of the pulse for tens of nanoseconds pulse, and the breakdown strengths of the three kinds of polypropylene films are almost identical for different applied voltages, which show a weak correlation between the thickness of the dielectric and the breakdown field. The expected breakdown strength of tens of nanoseconds pulse defined in this paper is not significantly higher than the mean value of the hundreds of nanoseconds pulse and the dc condition, suggesting that the breakdown of a thin polypropylene film is mainly determined by the electrical field but not the voltage-time cumulative effect. All these observations strengthen the conclusion that the breakdown of a thin polypropylene film is an intrinsic phenomenon. [ABSTRACT FROM AUTHOR]

Current transmission efficiency in a conical transition magnetically insulated transmission line (MITL) has been studied experimentally on a 1.0-MV linear transformer driver system, which has 10 identical cavities connected in series with MITL. Transmission efficiencies of anode current as high as 98.4% and 93.1% could be achieved when the MITL operates at load-limited and self-limited flows, respectively. As for the cathode current, because of the sufficient length of conical transition MITL, cathode current is also able to sustain high transmission efficiency. But as long as the diode gap is too large, many of the electrons will be launched into the anode–cathode gap and the cathode current near the diode drastically decreases. Particle-in-cell simulations were conducted to validate the conclusions. The simulation results agree with experiments. [ABSTRACT FROM PUBLISHER]