Search

The modular multilevel converter (MMC) is a promising candidate for high-/medium-voltage high-power applications such as medium voltage ac drives due to its modularity, reliability, and scalability. The main challenge of a conventional MMC is low-frequency operation. Capacitor voltage ripple is inversely proportional to the operating frequency. Hence, operating at low frequency necessitates employing large submodule capacitances to limit voltage ripple or the utilization of energy equalization modules (EEMs). The first option negatively affects converter lifetime, and the second option requires a large number of semiconductor devices and isolating transformers. In this article, a modified MMC topology with self-energy equalization is proposed to ensure converter operation with balanced capacitor voltages with low ripple during zero-/low-frequency conditions. Operating with balanced capacitor voltages with low ripple is achieved by maintaining the same energy level in the involved upper and lower arms. A low device count alternative to the EEMs approach is proposed in this work. Detailed illustration of the operational concept and design of the associated passive components is presented. The performance of the proposed medium voltage ac drive is elucidated through simulation and experimental results. [ABSTRACT FROM AUTHOR]

In this article, three different types of pulse generators based on multimodule boost converter ringing circuit are presented, namely, interleaved, stacked, and interleaved–stacked with full design and operational concept. The interleaved version is advantageous in generating a burst of pulses with moderate voltage magnitude, where the used modules are fed from a common dc source. On the other hand, the stacked multimodule version can be used to generate high-voltage pulsed output from synchronized modules with a moderate voltage rating. This can be done by feeding the modules from isolated dc sources while connecting their outputs in series. Finally, the interleaved–stacked version can be used for generating a burst of pulses with high-voltage magnitude. The presented pulse generators are valid for resistive loads with exponential decay pulses. The suggested pulse generators are simple and require semiconductor devices with moderate voltage ratings. For given pulse specifications, a detailed design for the passive components of each version is presented in this article. The simulation and experimental results are used to validate the suggested topologies. [ABSTRACT FROM AUTHOR]

This paper proposes a medium-/high-voltage high-power hybrid modular dc–dc converter to interconnect two different dc-voltage levels in medium-/high-voltage dc grids. The converter consists of half-bridge submodules (SMs) rated at a moderate voltage level, i.e., series connection of semiconductor devices is avoided while connecting two high dc-voltage levels. The proposed architecture provides self-balancing operation, i.e., unlike conventional modular converters, no need for capacitor voltage measurement, which enhances the system reliability and simplicity. Sequential charging/discharging of SMs capacitors is adopted in the proposed approach to ensure a self-balanced operation. The proposed architecture can provide a high conversion ratio as well as power transfer in both directions, i.e., bidirectional dc–dc converter. Detailed illustration of the proposed approach operational concept, design, and overall control system is presented. Simulation and experimental results are presented to show the viability of the proposed configuration and validate the claims. [ABSTRACT FROM AUTHOR]

In this paper, a dc–ac buck converter is proposed as a grid-side converter in high voltage dc (HVdc) transmission systems for high-power renewable energy source grid integration. The proposed architecture consists of multimodules of half-bridge voltage source converters (HB-VSCs). The dc terminals of the HB-VSCs are connected in series across the entire dc link (i.e., capacitor tapped), whereas their ac outputs are connected to multiwinding transformers to provide the three-phase terminals for ac grid integration. The proposed grid-connected capacitor-tapped multimodule converter (CT-MC) architecture, inspired from the HVdc shunt tap proposed by ABB, provides a dc–ac conversion with a relatively moderate voltage rating of semiconductor devices. It also provides operation with a lower number of semiconductor devices, gate driver circuits, voltage sensors, and lower total MVA rating of semiconductor devices (67%) compared with the conventional three-phase HB modular multilevel converter, which positively affects the system cost and reduces the computational burden of the employed controller. In this paper, the operational concept and control of the CT-MC are presented along with a capacitor voltage balancing approach. Simulation results are presented during normal and abnormal conditions to show the viability of the proposed architecture. Finally, a scaled down prototype for the CT-MC is employed to validate the converter operation. [ABSTRACT FROM AUTHOR]

Conventional Modular Multilevel Converter (MMC) with Half-Bridge Sub-Modules (HB-SMs) can be used effectively as a solid-state high-voltage pulse generator to chop a high-voltage dc input into a bipolar pulsed output voltage without employing neither high-voltage semiconductor switches nor series-connected switches. Nonetheless, its boosting capability is constrained. In this paper, a hybrid boost MMC-based bipolar high-voltage pulse generator is proposed where each arm contains a combination of Full-Bridge SMs (FB-SMs) and HB-SMs. The HB-SMs and FB-SMs have the same rated voltage. The proposed approach is able to generate bipolar pulses, and operates with a wide range of boosting capability. Detailed illustration of the proposed configuration and its operational concept are presented. Simulation models for the proposed approach are built, for different FB-SMs to HB-SMs ratios, using Matlab/Simulink platform. Experimental results for a scaled-down prototype are presented to validate the concept. [ABSTRACT FROM PUBLISHER]

The conventional unipolar Marx generator can be employed for bipolar pulsed electric field by adding a high-voltage H-bridge at the load side which necessitates stacked switches. Alternatively, bipolar Marx generator with low-voltage switches can be employed. The existing bipolar Marx generators are typically fed from dc supplies, where polarized capacitors are employed. The capacitance of involved capacitors is selected such that the total energy stored in the generator's capacitors is higher than the bipolar pulse energy. As a result, polarized capacitors with relatively high capacitances are required. In addition, a high number of controlled switches per stage are required (at least four switches per stage). In this paper, a new solid-state bipolar Marx pulse generator with only three controlled switches per stage is proposed. The proposed generator is fed from sinusoidal/square ac voltage and non-polarized capacitors with low capacitance are employed. The proposed bipolar Marx-generator can be used effectively with resistive loads for exponential pulse generation. A detailed illustration of the proposed approach is presented and a discussion, to elucidate the differences between the proposed pulse generator and the other existing ones, are presented. Simulation results for the proposed pulse generator are presented to validate the concept. Finally, experimental results have been obtained from a low-voltage model of the proposed generator. [ABSTRACT FROM AUTHOR]

This paper presents a new high-voltage pulse generator, which is based on positive and negative buck-boost (BB) converters fed from a relatively low voltage dc supply. The proposed generator is able to generate unipolar or bipolar high-voltage pulses via operating the BB converters with series or parallel connected outputs respectively using a common input dc source. The components of each converter are rated at half of the pulsed voltage magnitude in the unipolar mode. The converters in the proposed pulse generator operate in discontinuous conduction mode. This enhances system efficiency, as the circuit only operates when it is desired to generate a pulsed output voltage, otherwise the circuit is switched to idle mode with zero current. Detailed illustration of the proposed approach is presented along with a full design of the system components for given output pulse specifications. Finally, simulation and experimental results are presented to validate the proposed concept. [ABSTRACT FROM PUBLISHER]

Pulsed electric field is a commonly used and effective disinfection method in drinking water treatment applications. In this paper, a transformerless unipolar/bipolar high-voltage pulse generator is presented with well-regulated pulsed output voltage for drinking water treatment via underwater pulsed corona discharge. The proposed high-voltage pulse generator is fed from a relatively low-voltage dc supply. Then, capacitor–diode voltage multiplier centrally fed from a dc–dc boost converter is used to elevate the input voltage to a proper high-voltage level. Finally, a modular multilevel converter is employed to chop the elevated voltage into unipolar or bipolar pulsed output voltage (based on the user selection). The suggested arrangement provides a high-voltage gain with relatively low-voltage components, i.e., neither high-voltage nor series-connected components are needed in the proposed approach. A comparison between the proposed approach and the other Marx-Based pulse generators has been held to show the merits of the proposed approach. A detailed design of the generator passive components and semiconductor devices has been presented. Simulation and experimental results are presented for the unipolar as well as the bipolar pulsed output to validate the proposed concept. [ABSTRACT FROM AUTHOR]

Bipolar repetitive high-voltage pulse generators are commonly used in modern pulsed power applications. Conventionally, bipolar high-voltage pulses can be generated by adding a high-voltage H-bridge at the output stage of a unipolar high-voltage pulse generator which increases complexity and cost of the bipolar high-voltage pulse generator. In this paper, a boost-inverter-based bipolar high-voltage pulse generator with high-voltage gain is proposed. The proposed generator can provide high-voltage bipolar output pulses with the desired specifications from a low input dc voltage. The proposed generator is based on employing two bidirectional boost dc–dc converters, where the load is connected differentially between the boost converters’ output terminals. In the proposed approach, four controlled switches are required. Only two out of these four switches are rated at the high-voltage output level which affects positively the system cost. A detailed illustration of the proposed approach along with the design of its passive components is presented in this study. Simulation and experimental results are used to validate the proposed approach. [ABSTRACT FROM AUTHOR]

Repetitive high pulsed electric field (PEF) is an effective method to kill microorganisms and bacteria in water treatment applications. The PEF can be generated by applying high-power electromagnetic pulse across the sample to be treated. There are two main types of high-voltage pulse generators, namely, unipolar and bipolar. In this paper, a full-bridge submodule-based modular high-voltage pulse generator, having the ability to generate unipolar and bipolar high-voltage pulses with different shapes from a relatively low-voltage input dc supply, is proposed. In the proposed configuration, relatively low-voltage insulated gate bipolar transistors (IGBTs) are required to generate the high-voltage bipolar pulses. A thyristor rated at the level of the pulsed output voltage is required in the proposed configuration to bypass the load during the charging process of capacitors. In the proposed approach, a thyristor is used instead of the self-commutated high-voltage switch (e.g., series-connected IGBTs), as thyristors are available with high-voltage ratings and possess inherent reverse voltage blocking capability. A detailed illustration of the proposed configuration and its operational concept are introduced in this paper. Simulation and experimental results are presented to validate the proposed approach. [ABSTRACT FROM AUTHOR]

Repetitive Pulsed Electric Field (PEF) is a common technique for disinfecting liquids. By applying adequate PEF across germ cell membranes, an irreversible electroporation process, and cell destruction can be achieved. The PEF can be generated by applying a repetitive pulsed voltage using a high-voltage pulse generator across the cell membrane. Unipolar and bipolar high-voltage pulse generators are commonly used. Bipolar pulse generators can be implemented by employing a unipolar generator with an H-bridge output stage. The main disadvantage of this method is that the switches of the H-bridge are rated at the output high-voltage level, i.e. series-stacked semiconductor devices should be employed with static and dynamic voltage sharing to implement high-voltage switches. In this paper, a half-bridge submodule-based bipolar modular high-voltage pulse-generator fed from a relatively low-voltage dc supply is proposed. In the proposed approach, relatively low-voltage Insulated Gate Bipolar Transistors (IGBTs) are required to generate the high-voltage bipolar pulses. A detailed illustration of the proposed concept is presented. Simulation results are used to assure the viability of the proposed concept. Finally, experimental results have been obtained from a low-voltage model of the proposed generator. [ABSTRACT FROM AUTHOR]

This paper presents a new configuration for integrated on-board battery chargers of electric vehicles (EVs) incorporating symmetrical six-phase machines. The configuration proposes an exclusive utilization of a nine-switch converter (NSC) along with the machine windings during both propulsion and charging of EVs. The proposed configuration has the advantage of employing a reduced number of components in both the EV (on-board) and charging station (off-board), with the privilege of avoiding machine electromagnetic torque production during charging/vehicle-to-grid (V2G) mode of operation. During charging/V2G mode, the NSC is turned into a conventional three-phase pulse width modulation rectifier and is directly connected to the three-phase mains through the machine windings. Conventional three-phase transformers can be employed for galvanic isolation. Switching between propulsion and charging modes is carried out using a simple hardware reconfiguration. Control schemes for both propulsion and charging/V2G modes are elaborated, along with the principles of operation of the NSC. Experimental results are provided to validate the theoretical deductions for the different operating modes. [ABSTRACT FROM PUBLISHER]

High-Voltage pulse generators are commonly used in biotechnology, medicine, industrial applications, food processing and drinking water purification. The dc-dc boost converter has been used before in pulsed applications for its ability to amplify a relatively low input dc voltage to a high-voltage output. A high-voltage solid-state chopping switch is then used to chop the generated high output voltage. In this work, a boost-converter based ringing circuit with high voltage gain is proposed for water treatment applications. The basic concept of the proposed approach depends on operating the boost converter under discontinuous current conduction. With the proposed approach, the chopping high-voltage switch at the output stage is eliminated, which positively affects the system cost and efficiency. A full-design of the circuit and passive components is presented to ensure that the desired pulse specifications are achieved. The proposed approach has been validated using simulation and experimental results. [ABSTRACT FROM AUTHOR]

In order to generate bipolar high-voltage (HV) pulses across certain load from HV dc (HVdc) power supply, a voltage source inverter (VSI) stage should be inserted between the load and the supply. In order to meet the required HV level, series connection of semiconductor devices should be employed with dynamic voltage sharing between the involved devices. Modular multilevel converter (MMC) can be used instead of the conventional two-level VSI to alleviate the complexity introduced by the deployment of series-connected devices. The voltage level of the HVdc power supply and the voltage rating of the available semiconductor devices determine the suitable number of MMC voltage levels ( $N$ ). Capacitor voltage balancing is a vital issue for proper operation of the MMC. In general, conventional sensor-based balancing techniques require a significant amount of measurements, which increases the complexity of the system. In addition, the high dv/dt during switching times causes electromagnetic interference, which may adversely affect the accuracy of the measurements. In this paper, a sensorless voltage balancing technique is proposed for the MMC-based bipolar HV pulse generator that reduces the system sensitivity, cost, and complexity. A detailed illustration of the proposed approach is presented in this paper. The simulation and experimental results are used to validate the proposed concept. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) have become one of the most promising topologies for high-voltage dc–ac conversion. DC-side fault blocking capability of the MMC has prompted significant research in recent years. In this paper, a new switched capacitor submodule (SCSM) for MMCs is proposed which provides operation with DC fault blocking capability. In addition, successful voltage balancing is achieved with half the number of voltage sensors used with existing MMC cells. Generally, conventional sensor-based balancing techniques require a significant amount of measurements, 2m(N-1) voltage sensors, and 2m current sensors for an N-level m-phase MMC. The proposed cell will thus aid in reducing the complexity of the control system. A detailed illustration of the operational concept of the proposed architecture is presented in this paper. A comparison between the proposed SCSM and other existing MMC cells has been included to highlight the benefits of the proposed SCSM. A simulation model for an MMC-based HVDC system along with the proposed cell has been built to test its performance during normal as well as abnormal operating conditions. The simulation results show the effectiveness of the proposed architecture. [ABSTRACT FROM PUBLISHER]

The most recent literature on multiphase machine drives is based on voltage-source converter (VSC) systems utilizing different modulation techniques. Very little attention is given to the multiphase current-source converters (CSCs). Applying CSCs in high-power multiphase drive systems is promising and can effectively solve many technical problems associated with conventional VSC-based systems. This paper proposes a space vector pulsewidth-modulation (SVPWM) scheme suitable for a five-phase CSC. Generally, in SVPWM-CSCs, a current path should be provided for the dc-link current by ensuring that one pair of upper and lower switches is always on. Applying this constraint yields 25 different space vectors, which are mapped into two concentric decagons with ten equal sectors in the $\alpha\beta$ and $xy$ sequence planes. Each sector has two active-large vectors, two active-small vectors, and a null vector. Moreover, the active-large vectors in the $\alpha\beta$ plane are active-small vectors in the $xy$ plane, and vice versa. In the proposed scheme, the ampere-second concept is utilized to determine the ratio between the dwelling times of the large and small vectors such that the $xy$ current components are nullified, the utilization of the input dc-current is maximized, and the switching transitions are minimized, which, in turn, minimizes the CSC switching losses. The proposed scheme can effectively provide sinusoidal converter currents, which is suitable for motor drives and energy conversion applications. The proposed scheme is verified using a 1-kW prototype five-phase induction motor fed by a five-phase CSC. [ABSTRACT FROM PUBLISHER]

Pulsed electric field (PEF) can be used effectively in water treatment applications by passing infected water through two electrodes excited from a high voltage pulsed power supply which guarantees killing the harmful germs. In this paper, a new high-voltage pulse-generator with closed loop control of its output voltage is presented for treating water via underwater pulsed streamer corona discharge. The proposed generator is fed from a low AC voltage source (utility mains 220 V, 50 Hz) which makes it suitable for domestic applications. The proposed topology provides transformer-less operation which reduces the system size and enhances the overall efficiency. The proposed topology is based on capacitor-diode voltage multiplier (CDVM) circuits in conjunction with DC-DC converters (Boost and Buck-Boost converters). The simulation and experimental results elucidate the proposed configuration. [ABSTRACT FROM AUTHOR]

The four-switch three-phase (FSTP) inverter has been proposed as an innovative inverter design to reduce the cost, complexity, size, and switching losses of the dc–ac conversion system. Traditional FSTP inverter usually operates at half the dc input voltage; hence, the output line voltage cannot exceed this value. This paper proposes a novel design for the FSTP inverter based on the topology of the single-ended primary-inductance converter (SEPIC). The proposed topology provides pure sinusoidal output voltages with no need for output filter. Compared to traditional FSTP inverter, the proposed FSTP SEPIC inverter improves the voltage utilization factor of the input dc supply, where the proposed topology provides higher output line voltage which can be extended up to the full value of the dc input voltage. The integral sliding-mode control is used with the proposed topology to optimize its dynamics and to ensure robustness of the system during different operating conditions. Derivation of the equations describing the parameters design, components ratings, and the operation of the proposed SEPIC inverter is presented in this paper. Simulation model and experimental setup are used to validate the proposed concept. Simulations and experimental results show the effectiveness of the proposed inverter. [ABSTRACT FROM AUTHOR]

Two-level voltage-source converters and half-bridge modular multilevel converters are among the most popular types of HVDC converters. One of their serious drawbacks is their vulnerable nature to dc-side faults, since the freewheeling diodes act as a rectifier bridge and feed the dc faults. The severity of dc-side faults can be limited by connecting double thyristor switches across the semiconductor devices. By turning them on, the ac current contribution into the dc side is eliminated and the dc-link current will freely decay to zero. The main disadvantages of this method are: high dv/dt stresses across thyristors during normal conditions, and the absence of bypassing for the freewheeling diodes during dc faults since they are sharing the fault current with thyristors. This paper proposes combining and connecting the double thyristor switches across the ac output terminals of the HVDC converter. The proposed protection scheme provides advantages, such as lower dv/dt stresses and lower voltage rating of thyristor switches in addition to providing full segregation between the converter semiconductor devices and ac grid during dc-side faults. A simulation case study has been carried out to demonstrate the effectiveness of the proposed scheme. [ABSTRACT FROM AUTHOR]

Offshore wind energy is now seen as a key contributor for the future renewable energy mix. HVDC technology is among the chief technologies enabling widespread use of offshore wind. Thanks to their numerous advantages, voltage-source converter-based-HVDC (VSC-HVDC) systems are expected to be the technology of choice. Unfortunately, most of VSCs are defenseless against dc-side faults, such as two-level VSCs, and half-bridge modular multilevel converters. This paper proposes the buck-boost inverter-based-HVDC system (BBI-HVDC) as a means to overcome the limitations of the classical VSC-HVDC systems. The proposed configuration does not only provide sinusoidal three-phase voltage, but also provides complete blocking capability of ac-side contributions during a dc-side fault. The latter is achieved by simply disabling the gating signals to the switches upon fault detection. The performance of the proposed system is illustrated during normal conditions, ac-side faults, and dc-side faults. A simulation case study comparing the performance of the conventional HVDC converters with the proposed system during dc-side faults is conducted. The simulation results reveal the promising performance under normal operation as well as a significant decrease in the dc fault current due to the ac-side contribution blocking capability of the BBI-HVDC system during dc-side faults. [ABSTRACT FROM AUTHOR]

An interline dynamic voltage restorer (IDVR) is invariably employed in distribution systems to mitigate voltage sag/swell problems. An IDVR merely consists of several dynamic voltage restorers (DVRs) sharing a common dc link connecting independent feeders to secure electric power to critical loads. While one of the DVRs compensates for the local voltage sag in its feeder, the other DVRs replenish the common dc-link voltage. For normal voltage levels, the DVRs should be bypassed. Instead of bypassing the DVRs in normal conditions, this paper proposes operating the DVRs, if needed, to improve the displacement factor (DF) of one of the involved feeders. DF improvement can be achieved via active and reactive power exchange (PQ sharing) between different feeders. To successfully apply this concept, several constraints are addressed throughout the paper. Simulation and experimental results elucidate and substantiate the proposed concept. [ABSTRACT FROM AUTHOR]

The nine-arm modular multilevel converter (9A-MMC) has been recently proposed as a reduced MMC topology variation for six-phase drive applications, with 25% reduction in the number of employed arms and associated components, compared to a standard dual three-phase MMC, however with a limited output voltage amplitude. This paper proposes a hybrid 9A-MMC comprised of half-bridge submodules (SMs) in both the upper and lower arms, and full-bridge SMs in the middle arms. By employing the negative-voltage state of the full-bridge SMs, the hybrid 9A-MMC avoids the limitations imposed on the dc-link voltage utilization, while achieving further reduction in the component count, compared to a standard 9A-MMC with identical half-bridge SMs. The operating principles of the proposed hybrid 9A-MMC are illustrated with mathematical analysis, whereas its characteristics are verified through both simulation and experimentation. An assessment of the proposed topology quantifying its employed components is also provided, in comparison to other MMC-based six-phase machine drives. [ABSTRACT FROM AUTHOR]

Converting existing ac transmission lines to an extended multiterminal three-wire bipolar HVDC system can be considered a cost-effective way to interconnect dispersed offshore wind farms to onshore ac grids instead of building new bipolar HVDC systems. To automatically coordinate between different converters in a multiterminal HVDC (MTDC) system, droop control techniques have been adopted as an effective means without the need for fast communications between units. The droop control design is mainly dependent on the line resistances. This paper shows that the equivalent resistance of a three-wire bipolar system changes based on the operational mode. The modification to droop control design of an MTDC equipped with a three-wire bipolar system is then presented to tackle this resistance variation with the operating condition. Two types of MTDC systems are considered in this work, namely, radial parallel and meshed parallel systems. Different simulation studies have been conducted to validate the results of the presented analysis. [ABSTRACT FROM PUBLISHER]

Five-phase induction machines are generally modeled using multiple dq planes or using a phase variable model. This paper considers modeling five-phase induction machines using a voltage-behind-reactance (VBR) configuration. This configuration lends itself suitable for time-domain circuit-based simulators as the MATLAB/Simulink SimPowerSystems (SPS) toolbox. The stator electrical dynamics are represented in five-phase coordinates, while the rotor electrical circuit is modeled using rotor flux linkage as the state variable and expressed in the dq stator reference frame. The VBR model is equivalent to a conventional dq model; however, it facilitates the connection of an external inductance without affecting numerical accuracy and calculation efficiency. It also facilitates the simulation of different winding connections, series-connected multimotors, and open phase(s) conditions. The model is, first, derived for a magnetically linear system and then it is extended to include the effect of magnetic saturation. The flux correction method is used to represent the effect of magnetic saturation with a simple modification to represent the effect of cross coupling between fundamental and third sequence planes due to saturation effect. The dynamic cross saturation is considered by adding compensating terms that depend on magnetizing inductance variation. The proposed model is experimentally verified using a prototype 1.5-hp five-phase induction machine under different operating conditions. [ABSTRACT FROM AUTHOR]

Power generation through wind is expected to play a major role in the world's future energy portfolio. Nevertheless, wind power integration remains a challenging research area due to the special characteristics of wind power generation. Specifically, offshore wind has received significant attention worldwide due to the vast generation potential available. The electrical infrastructure of offshore wind farms is thus of significant importance. The multi-terminal HVDC solution represents a preferable solution and has shown promise in solving wind farm interconnection problems. Droop control techniques have been proposed as a means to regulate the DC voltage and facilitate the automatic coordination between different converters without the need for fast communication between units. Different methodologies have been developed to select the droop gains to satisfy the system performance specifications. In this work, a control design methodology is proposed for power sharing among the multi-terminal HVDC feeders providing that the power transmission efficiency is optimized. A simulation study on a 400-kV/1000-MW four-terminal HVDC transmission topology is conducted to ensure the validity of the proposed methodology. [ABSTRACT FROM PUBLISHER]

Voltage source converter (VSC)-based high voltage DC (HVDC) transmission is considered the future of offshore power transmission. This paper aims at providing a reliable VSC-HVDC transmission system architecture between offshore wind farms and onshore grids. In this paper, a large-capacity, low-speed flywheel energy storage system (FESS) based on a squirrel cage induction machine is applied in parallel with the VSC-HVDC at the grid side converter. The FESS is dedicated for surge power (due to power flow imbalance during fault) absorption instead of being dissipated in the form of resistive losses. Since the duration of these surges is relatively small, it has been shown that the flywheel can effectively mitigate this problem. In addition to the fault ride-through support during fault conditions, the FESS is employed for power leveling functionality during normal operation. The performance parameters of the proposed approach are investigated via both simulation and experimental results. A 132-kV, 100-MW HVDC system is simulated using MATLAB/Simulink during normal and fault conditions. The proposed architecture is substantiated experimentally through a scaled down test rig with a 2-kW FESS. [ABSTRACT FROM AUTHOR]

Despite the increased interest in multiphase induction machines for safety-critical applications, machine parameter identification for the different sequence planes is still a challenging research point. In most available literature, the effect of nonfundamental sequence planes is overlooked due to the assumption of sinusoidal winding distribution and healthy operation. However, in a single layer or concentric winding layout with an odd number of phases, the effect of flux produced by nonfundamental sequence planes cannot be ignored for the open-phase case. This paper proposes a simple offline method to estimate the parameters of a five-phase induction machine corresponding to different sequence planes. The proposed technique can estimate the stator leakage inductance as well as the magnetizing inductance of both fundamental and third sequences by applying a quasi-square voltage to the stator winding while the machine is running at no-load. Consequently, the rotor circuit parameters of the fundamental sequence plane can be simply obtained by deducting the stator impedance from the blocked rotor machine impedance. For the third sequence plane, an approximate relation to estimate these parameters based on the measured fundamental sequence rotor parameters is also given. An experimental 1.5 Hp prototype machine is used to verify the proposed technique. [ABSTRACT FROM PUBLISHER]

Direct-drive permanent magnet (PM) generators have become a strong contender in medium and large rating wind energy conversion systems as they not only provide higher efficiency and annual energy production, but also reduce the operational and maintenance cost. PM generators with nonoverlap single-layer windings provide a cost-effective design variation that eases manufacturing, reduces torque ripples, enhances voltage quality, and provides fault tolerant capability. The performance of such machines depends mainly on the proper selection of the pole and slot numbers, which results in negligible coupling between phases. The preferred slots per phase per pole (SPP) ratios eliminate the effect of low order harmonics in the stator magnetomotive force (MMF), and thereby the vibration and stray loss are reduced. This paper proposes a new three-phase winding configuration based on the 20 slots/18 poles five-phase PM machine. The proposed design is compared with the well-known 24 slots/20 poles three-phase PM machine. The comparison shows that the proposed generator offers reduced torque ripples, improved output voltage quality, and less core loss for the same machine volume. [ABSTRACT FROM PUBLISHER]