Search

It is well-known that when high currents flow through a vacuum gap, anode spots are formed on the anode surface. However, anode flare phenomena are also observed in low-current vacuum discharges. The objective of this article is to experimentally observe the spatial distribution of excited Cu atoms and ions generated from a single cathode spot (CS) and to interpret the mechanism of the anode flare at low currents (40–80 A). Optical emission spectroscopy (OES) and laser-induced fluorescence (LIF) techniques have been used for investigating low-current vacuum arc discharge confined to axial magnetic fields (AMFs). The effects of AMFs and arc currents on the axial distribution of the radiation intensity were investigated for different copper ionization states (Cu I and Cu II). The highest luminance was found near the electrodes for both excited neutral copper atoms and ions, and only weak spectral lines of excited Ni atoms were detected in the near-anode region. With increasing the external AMF, a bright “spot” appeared near the anode surface. In the visible light range, excited atoms were the main contributor to anode flare in low-current vacuum discharge. As measured by LIF, the density of copper atoms near the anode increased from 10 $\times 10^{17}$ to 14 $\times 10^{17}\,\,\text{m}^{-3}$ when the applied magnetic fields increased from 31 to 74 mT. The anode flare contains far more excited atoms from the cathode material than the anode material. They are the results of cathodic plasma expansion to reach the anode after charge neutralization and reflection on the anode surface. For the single CS, the observed fact that a tiny number of atoms leave the anode surface and participate in the anode flare is more likely the result of a sputtering effect rather than thermal evaporation by cathode electron stream. [ABSTRACT FROM AUTHOR]

The evolution processes of vacuum breakdowns in single- and double-break vacuum interrupters are reported in this paper, in order to reveal the formation mechanisms for the conductive channels in vacuum arcs. Breakdown experiments in two vacuum interrupters containing 10–30 mm gaps with single-break and double-break are studied. The light emission during breakdowns is observed by an intensified charge coupled device camera, with the current and voltage waveforms being recorded simultaneously. According to the results, there is no difference between the evolution processes of breakdowns in small gaps and large gaps. The establishment of the conductive channel and sustaining of the vacuum arc can be achieved by the effect of the cathode without any contribution from the anodic glow. In the double-break interrupter, the transition from insulation to conduction for the two serial connected gaps starts simultaneously but evolves independently. [ABSTRACT FROM AUTHOR]

Anode surface temperature has a significant impact on the interruption capacity of a vacuum circuit breaker. The objective of this paper is to experimentally understand the decay process of anode surface temperature after extinguishing a high-vacuum arc with a large contact gap. The anode surface temperature after current zero was measured by a two-color pyrometer and arc modes observation was recorded by a highspeed charge-coupled device. A pair of asymmetric butt type contacts (contact materials: CuCr25 and CuCr50) was subjected to an axial magnetic field in a demountable vacuum chamber. The experimental result shows that there are two modes in decay processes of anode surface temperature: Mode I and Mode II. Mode I describes the anode surface decay process after diffuse low-current extinction and Mode II corresponds to high current extinction. In addition, the decay time of anode surface temperature will last longer, if the proportion of chromium rises from 25% to 50% in anode material. [ABSTRACT FROM PUBLISHER]

We report our measurements of anode current density distributions for different modes in vacuum arc discharge using a split-anode and a cup-shaped axial magnetic field cathode configuration system. The modes investigated included the diffuse arc and anode spot. The anode surface was divided into four regions: one central region and three symmetrical-disposed peripheral annular-arc regions. Three different-sized central regions were selected with diameters of 12, 18, and 20 mm. The contact material was CuCr25 (25% Cr). The arc current in the tests ranged from 6 to 14 kA (rms) at 50 Hz. The opening velocities were 1.8 and 2.4 m/s, respectively. The currents of the four areas on the anode contact were measured by four Rogowski coils situated outside the vacuum chamber. The experimental results show the current density distribution in different arc modes. For the diffuse arc mode with arc currents of 6 and 8 kA (rms), the average current density in the central region at current peak ranged from 8.5 to 15.9 A/mm ^2 . The anode spot current density ranged from 31.9 to 37.7 A/mm ^2 , estimated from the current density in the eroded region caused by the anode spots covering the entire central region of diameters 12 and 18 mm, at currents of 12 and 14 kA, respectively, regarded as the lower limit current density of the anode spot. Moreover, the dependence of the current density distribution on opening velocity in diffuse arcs was slight. For the anode spots, the current density distribution with higher opening velocity was more concentrated. [ABSTRACT FROM PUBLISHER]