Search

Voltage-sourced converter (VSC)-based static synchronous compensators (STATCOMs) are used for voltage regulation in transmission and distribution systems. Unlike PWM-controlled STATCOMs, angle-controlled STATCOMs are switched at line frequency to limit the system losses. In recent years, angle-controlled STATCOMs have been deployed by utilities for the purpose of transmission system voltage regulation, voltage stability improvement, and increasing operational functionality. Despite the superior feature on voltage waveform quality and efficiency, the practical angle-controlled STATCOMs suffer from the over-current (and trips) and possible saturation of the interfacing transformers caused by negative sequence current during unbalanced conditions and faults in the utility. This paper specifically proposes a control structure to improve the angle-controlled STATCOMs performance under unbalanced conditions and faults. The main improvement is a substantial decrease in the negative sequence current and dc-link voltage oscillations under power system faults by the proposed control. This eliminates the need to redesign the STACOM power components to operate under fault current and dc-link voltage oscillations. The proposed control structure is designed based on adding appropriate oscillations to the conventional angle-controller output that is the control angle by which the VSC voltage vector leads/lags the line voltage vector. Since this control structure uses two angles for controlling the VSC output voltage, it is called dual angle control (DAC). PSCAD/EMTDC and experimental results verify the validity of the proposed control structure under unbalanced system conditions and faults. The experiments were conducted on a transient network analyzer, a unique hardware-based flexible ac transmission system simulator which was designed to study system faults and transients for a 2 × 100 MVA STATCOM field installation. [ABSTRACT FROM AUTHOR]

This paper presents an approach to optimally select and allocate flexible ac transmission (FACTS) devices in a distribution network in order to minimize the number of voltage sags at network buses. The method proposed is based on the optimization of a preselected objective function using simple and niching genetic algorithms (GA). The objective of the optimization is to achieve the improvement in overall system sag performance of the network. Using proposed GA-based optimization, the location, the type and the rating of six (in total) FACTS devices are optimized simultaneously. Three types of FACTS devices are implemented in this study, namely, static var compensator, static compensator, and dynamic voltage restorer. The performance of the proposed algorithm is tested and illustrated on 295-bus generic distribution system. [ABSTRACT FROM PUBLISHER]

Flexible ac transmission system (FACTS) devices or their subderivative custom power devices are efficient and often used and recommended power-electronics-based devices for mitigation of voltage sags in electrical power system. With FACTS devices installed, the overall system (and individual bus) sag performance could significantly change depending on the type of the device used. In order to assess this change in sag performance in realistic large power systems, the classical (essentially static) fault calculation procedure should be amended to incorporate the effects of these devices on bus voltages. This paper presents a new approach of quasistatic sag analysis using a system impedance (Z bus ) matrix that incorporates FACTS devices. Three types of FACTS devices which are most often used in practical applications are considered in this study: static compensator, static var compensator, and the dynamic voltage restorer. The case studies based on the 295-bus generic distribution system are used to illustrate the modeling method and the effectiveness of these devices in sag mitigation. [ABSTRACT FROM PUBLISHER]

STATCOM is a FACTS controller that is used in power systems to regulate the line voltage, enhance the power transmission capacity and extend the transient stability margin. STATCOM is conventionally realized by a voltage-source converter; however, being a current injection device, its performance can be improved when realized by a current-source converter (CSC) that can generate a controllable current directly at its output terminals. In this paper, a STATCOM based on the current-source converter topology is proposed. The nonlinear model of the current-source converter, which is the source of the difficulties in the controller design, has been modified to a linear model through a novel modeling technique. The proposed modeling technique is not based on the linearization of a set of nonlinear equations around an operating point. Instead, the power balance equation and a nonlinear input transformation are used to derive a linear model independent of the operating point. This model acts as the basis for the design of a decoupled state-feedback controller. The proposed STATCOM has been simulated using the PSCAD/EMTDC package. The simulation results show that a CSC-based STATCOM can result in excellent current and voltage waveforms as well as very short response time while operating at a low switching frequency. This makes the proposed scheme suitable for high power applications. [ABSTRACT FROM PUBLISHER]