Search

High-frequency (HF) oil-immersed transformers with small size and light weight have been paid wide attention by researchers. Its oil–paper insulation frequently withstands HF over-voltages at frequencies of several kilohertz and above, resulting in the too early failure of oil–paper insulation. In order to investigate the effect of HF on oil–paper insulation, this article investigates the partial discharge (PD) characteristics of oil–paper insulation under HF stress. The experimental results show that a frequency-induced inflection point is existed near 10 kHz and the PD parameters of HF voltages is much higher than that ac voltages. Besides, the theoretical mechanism is expounded to interpret and understand the formation process of frequency-induced inflection points more easily. It can be found that the change in frequency causes the change in the charge decay time constant and the residual charge on the insulating surface, resulting in the formation of the frequency-induced inflection point at HF. These results might contribute to determine the characteristics of PDs between HF voltages and ac voltages. It can provide references for the research and production of HF transformers. [ABSTRACT FROM AUTHOR]

Paper-based digital microfluidic biochips (P-DMFBs) have recently emerged as a promising low-cost and fast-responsive platform for biochemical assays. In P-DMFBs, electrodes and control lines are printed on a piece of photograph paper using an inkjet printer and carbon nanotubes (CNTs) conductive ink. Compared with traditional digital microfluidic biochips (DMFBs), P-DMFBs enjoy significant advantages, such as faster in-place fabrication with printer and ink, lower costs, and better disposability. Since electrodes and CNT control lines are printed on the same side of this paper, a critical design challenge for P-DMFB is to prevent control interference between moving droplets and the voltages on CNT control lines. Control interference may result in unexpected droplet movements and thus incorrect assay outputs. To address this design challenge, a control-fluidic codesign methodology is proposed in this paper, along with two demonstrative design flows integrating both fluidic design and control design, i.e., the droplet-oriented codesign flow and the electrode-oriented codesign flow. The droplet-oriented flow is suitable for designing biochips with sparse electrodes and relatively larger number of droplets, whereas the electrode-oriented flow is suitable for biochips with dense electrodes and smaller number of droplets. The computational simulation results of real-life bioassays demonstrate the effectiveness of the proposed codesign flows. [ABSTRACT FROM AUTHOR]

A multi responsive Schiff base sensor L with thiophenol moiety was synthesized by the single-step condensation method. The structural analysis of the sensor was proposed by 1H-NMR, UV- Visible absorption, HRMS and FT-IR spectroscopy. Sensor L exhibited an instant appearance of yellow color on the addition of copper ions. Since copper gave an intense color change, therefore detailed studies were performed for copper sensing w.r.t. designed sensor L. Selectivity and sensitivity of sensor concerning copper metal ions were established by performing various UV-Visible spectroscopic and colorimetric studies. The 1:1 binding framework of the L-Cu2+ complex is confirmed by Job’s Plot and further supported by DFT studies. With the help of Benesi-Hildebrand equation, the detection limit and the association constants were found to be $3.15 \times 10^{-6}$ M and $1.16 \times 10^{4}$ M−1, respectively. In addition, sensor L was transferred onto solid substrates including silica and paper strips for establishing its utility in the onsite detection of copper ions. [ABSTRACT FROM AUTHOR]

This paper studies the secure transmission in a multiuser broadcast channel where only the statistical channel state information of the eavesdropper is available. We propose to apply secret dirty-paper coding (S-DPC) in this scenario to support the secure transmission of one user and the normal (unclassified) transmission of the other users. By adopting the S-DPC and encoding the secret message in the first place, all the information-bearing signals of the normal transmission are treated as noise by potential eavesdroppers and thus provide secrecy for the secure transmission. In this way, the proposed approach exploits the intrinsic secrecy of multiuser broadcasting and can serve as an energy-efficient alternative to the traditional artificial noise (AN) scheme. To evaluate the secrecy performance of this approach and compare it with the AN scheme, we propose two S-DPC-based secure transmission schemes for maximizing the secrecy rate under constraints on the secrecy outage probability (SOP) and the normal transmission rates. The first scheme directly optimizes the covariance matrices of the transmit signals, and a novel approximation of the intractable SOP constraint is derived to facilitate the optimization. The second scheme combines zero-forcing dirty-paper coding and AN, and the optimization involves only power allocation. We establish efficient numerical algorithms to solve the optimization problems for both schemes. Theoretical and simulation results confirm that, in addition to supporting the normal transmission, the achievable secrecy rates of the proposed schemes can be close to that of the traditional AN scheme, which supports only the secure transmission of one user. [ABSTRACT FROM PUBLISHER]

In this paper, we present a practical method to construct dirty paper coding (DPC) schemes using sum codes. Unlike the commonly used approach to DPC where the coding scheme involves concatenation of a channel code and a quantization code, the proposed method embodies a unified approach that emulates the binning method used in the proof of the DPC result. Auxiliary bits are used to create the desired number of code vectors in each bin. Sum codes are obtained when information sequences augmented with auxiliary bits are encoded using linear block codes. Sum-code-based DPC schemes can be implemented using any linear block code, and entail a relatively small increase in decoder complexity when compared to standard communication schemes. They can also lead to significant reduction in transmit power in comparison to standard schemes. [ABSTRACT FROM AUTHOR]

Recently, there has been a lot of success in using the deterministic approach to provide approximate characterization of Gaussian network capacity. In this paper, we take a deterministic view and revisit the problem of wiretap channel with side information. A precise characterization of the secrecy capacity is obtained for a linear deterministic model, which naturally suggests a coding scheme which we show to achieve the secrecy capacity of the degraded Gaussian model (dubbed as “secret writing on dirty paper”) to within half a bit. [ABSTRACT FROM PUBLISHER]

Biological compounds like Dopamine (D), Xanthine (X), Ascorbic acid (AA) and Uric acid (UA) play a vital role in food, clinical and human metabolism. Since these compounds are present in biological fluids and have close standard potentials values, it is imperative to choose a method to sense these fluids without any electrochemical interference. Toray paper, with a porous gas diffusion layer imbibed with denser carbon fibers, is an excellent option that can be utilized as a working electrode for such sensing applications. Herein, the electroactivity of these compounds was tested using cyclic voltammetry and square wave voltammetry without any interference. The linear ranges for the compounds (D, X, AA, UA) are 10- $1000~\mu \text{M}$ , 7- $300~\mu \text{M}$ , 100- $1000~\mu \text{M}$ and 30- $1000~\mu \text{M}$ respectively, while the limits of detection are $9.67~\mu \text{M}$ , $6.54~\mu \text{M}$ , $97.12~\mu \text{M}$ and $28.74~\mu \text{M}$ respectively with S/N ratio of 1.5. Finally, the electrode was tested with human serum samples for the identification of D, X, AA and UA manifesting exceptional reproducibility. [ABSTRACT FROM AUTHOR]

New power allocation schemes taking both sum-rate and fairness into account for MIMO downlink communications employing successive zero-forcing dirty paper coding are presented in this letter. Specifically, using a revised l1-norm fairness measure that allows for a more comprehensive consideration when users have an unequal number of receive antennas, the optimal tradeoff between sum-rate and fairness for MIMO downlink communications with arbitrary channel statistics is completely characterized. A novel stochastic power allocation scheme capable of achieving this optimal tradeoff is also given. To put the optimal tradeoff into practical use, an explicit rule for selecting operating sum-rate from the tradeoff is then proposed. Simulation results show that the new scheme can yield higher sum-rate and better fairness at the same time. [ABSTRACT FROM AUTHOR]

Dirty paper coding is an interference pre-cancellation method for known interference at the transmitter and serves as a basic building block in the digital watermarking system. In this letter, we investigate the dirty paper model in the simplest digital communication system, where both the codeword and the interference are binary. For watermark embedment, we derive the relevant coding, the constant coding, and the symmetric relevant coding when the encoder focuses on the binary codeword and interference. The channel capacity is analyzed and the optimal parameter is discussed in the case. [ABSTRACT FROM AUTHOR]

We derive the capacity region of the two-user dirty-paper Gaussian multiaccess channel (MAC) with conferencing encoders. In this MAC, prior to each transmission block, the transmitters can hold a conference in which they can communicate with each other over error-free bit pipes of given capacities. The received signal suffers not only from additive Gaussian noise but also from additive interference, which is known noncausally to the transmitters but not to the receiver. The additive interference is modeled as Gaussian or uniform over a sphere. We show that the interference can be perfectly mitigated, i.e., that the capacity region without interference can also be achieved in its presence. This holds irrespective of whether the transmitters learn the interference before or after the conference. It follows as a corollary that also for the MAC with degraded message sets, the interference can be perfectly mitigated if it is known noncausally to the transmitters. To derive our results, we generalize Costa's single-user writing-on-dirty-paper achievability result to channels with dependent interference and not-necessarily Gaussian noise. [ABSTRACT FROM AUTHOR]

A wideband Rayleigh fading channel is considered with causal channel state information (CSI) at the transmitter and no receiver CSI. A simple orthogonal code with energy detection rule at the receiver (similar to pulse position modulation in IEEE Trans. Inf. Theory, vol. 46, no. 4, Apr. 2000 and IEEE Trans. Inf. Theory, vol. 52 no. 5, May 2006) is shown to achieve the capacity of this channel in the wideband limit. This strategy transmits energy only when the channel gain exceeds a threshold, hence only needs causal transmitter CSI. In the wideband limit, this capacity without any receiver CSI is the same as the capacity with full receiver CSI, which is proportional to the logarithm of the bandwidth. Similar threshold-based pulse position modulation is shown to achieve the capacity per unit cost of the dirty-tape channel (dirty paper channel with causal transmitter CSI and no receiver CSI), which equals its capacity per unit cost with full receiver CSI. Then, a general discrete channel with i.i.d. states is considered. Each input has an associated cost and a zero cost input “0” exists. The channel state is assumed to be known at the transmitter in a causal manner. Capacity per unit cost is found for this channel and a simple orthogonal code is shown to achieve this capacity. Later, a novel orthogonal coding scheme is proposed for the case of causal transmitter CSI and a condition for equivalence of capacity per unit cost for causal and noncausal transmitter CSI is derived. [ABSTRACT FROM PUBLISHER]

Superchannel transmission is a candidate to realize Tb/s-class high-speed optical communications. In order to achieve higher spectrum efficiency, the channel spacing shall be as narrow as possible. However, densely allocated channels can cause non-negligible inter-channel interference (ICI) especially when the channel spacing is close to or below the Nyquist bandwidth. In this paper, we consider joint decoding to cancel the ICI in dense superchannel transmission. To further improve the spectrum efficiency, we propose the use of Han–Kobayashi superposition coding. In addition, for the case when neighboring subchannel transmitters can share data, we introduce dirty-paper coding for pre-cancelation of the ICI. We analytically evaluate the potential gains of these methods when ICI is present for sub-Nyquist channel spacing. [ABSTRACT FROM PUBLISHER]

In this paper, the sequence families of which maximum correlation is determined by the Weil bound of exponential sums are revisited. Using the same approach, two new constructions with large family sizes and low maximum correlation are given. The first construction is an analog of one recent result derived from the interleaved structure of Sidel'nikov sequences. For a prime p and an integer M\vert (p-1), the new M-ary sequence families of period p are obtained from irreducible quadratic polynomials and known power residue-based sequence families. The new sequence families increase family sizes of the known power residue-based sequence families, but keep the maximum correlation unchanged. In the second construction, the sequences derived from the Weil representation are generalized, where each new sequence is the elementwise product of a modulated Sidel'nikov sequence and a modulated trace sequence. For positive integers d

In this paper, we consider precoder designs for multiuser multiple-input-single-output broadcasting channels. Instead of using a traditional linear zero-forcing (ZF) precoder, we propose a generalized ZF (GZF) precoder in conjunction with successive dirty-paper coding (DPC) for data transmissions, namely, the GZF-DP precoder, where the suffix “DP” stands for “dirty-paper.” The GZF-DP precoder is designed to generate a band-shaped and lower triangular effective channel F , such that only the entries along the main diagonal and the $\nu $ first lower-diagonals can take non-zero values. Utilizing the successive DPC, the known non-causal inter-user interferences from the other (up to) $\nu $ users are canceled through successive encoding. We analyze optimal GZF-DP precoder designs both for sum-rate and minimum user-rate maximizations. Utilizing Lagrange multipliers, the optimal precoders for both cases are solved in closed-forms in relation to optimal power allocations. For the sum-rate maximization, the optimal power allocation can be found through water filling, but with modified water levels depending on the parameter $\nu $ , while for the minimum user-rate maximization that measures the quality of the service, the optimal power allocation is directly solved in closed-form, which also depends on $\nu $ . Moreover, we propose two low-complexity user-ordering algorithms for the GZF-DP precoder designs for both maximizations, respectively. We show, through numerical results, that the proposed GZF-DP precoder with a small $\nu $ value (≤ 3) renders significant rate increments compared with the previous precoder designs, such as the linear ZF and the user-grouping-based DPC precoders. [ABSTRACT FROM PUBLISHER]

We consider the beamformer design for multiple-input multiple-output (MISO) broadcast channels (MISO BCs) using zero-forcing dirty paper coding (ZF-DPC). Assuming a sum power constraint (SPC), most previously proposed beamformer designs are based on the QR decomposition (QRD), which is a natural choice to satisfy the ZF constraints. However, the optimality of the QRD-based design for ZF-DPC has remained unknown. In this paper, first, we analytically establish that the QRD-based design is indeed optimal for any performance measure under a SPC. Then, we propose an optimal beamformer design method for ZF-DPC with per-antenna power constraints (PAPCs), using a convex optimization framework. The beamformer design is first formulated as a rank-1-constrained optimization problem. Exploiting the special structure of the ZF-DPC scheme, we prove that the rank constraint can be relaxed and still provide the same solution. In addition, we propose a fast converging algorithm to the beamformer design problem, under the duality framework between the BCs and multiple access channels (MACs). More specifically, we show that a BC with ZF-DPC has the dual MAC with ZF-based successive interference cancellation (ZF-SIC). In this way, the beamformer design for ZF-DPC is transformed into a power allocation problem for ZF-SIC, which can be solved more efficiently. [ABSTRACT FROM PUBLISHER]

Dirty paper coding (DPC) offers an information-theoretic result for pre-cancellation of known interference at the transmitter. In this letter, we propose practical DPC schemes that use only one error correction code. Our designs focus on practical use from the viewpoint of complexity. For fair comparison with previous schemes, we compute the complexity of proposed schemes by the number of operations used. Simulation results show that compared to previous DPC schemes, the proposed schemes require lower transmission power to maintain the bit error rate to be within 10^-5 . [ABSTRACT FROM PUBLISHER]

In this paper, we study the diversity-multiplexing-gain tradeoff (DMT) of wireless relay networks under the half-duplex constraint. It is often unclear what penalty if any, is imposed by the half-duplex constraint on the DMT of such networks. We study two classes of networks; the first class, called KPP(I) networks, is the class of networks with the relays organized in K parallel paths between the source and the destination. While we assume that there is no direct source-destination path, the K relaying paths can interfere with each other. The second class, termed as layered networks, is comprised of relays organized in layers, where links exist only between adjacent layers. [ABSTRACT FROM PUBLISHER]

This paper considers the downlink of a cognitive radio (CR) network formed by multiple primary and secondary transmitters, where each multiantenna transmitter serves a preknown set of single-antenna users. This paper assumes that the secondary and primary transmitters can simultaneously transmit their data over the same frequency bands to achieve high system spectrum efficiency. This paper considers the downlink balancing problem of maximizing the minimum signal-to-interference-plus-noise ratio (SINR) of the secondary transmitters subject to both the total power constraint of the secondary transmitters and the maximum interference constraint at each primary user due to secondary transmissions. This paper proposes solving the problem using the alternating direction method of multipliers, which leads to a distributed implementation through limited information exchange across the coupled secondary transmitters. This paper additionally proposes a solution that guarantees feasibility at each iteration. Simulation results demonstrate that the proposed solution converges to the centralized solution in a reasonable number of iterations. [ABSTRACT FROM AUTHOR]

The aspects of sum rate and fairness for dirty paper coding (DPC) based MIMO downlink communications are investigated in this paper. We first apply the $\ell _{1}$ -norm fairness measure to formulate the problem of fairness maximization for a given sum rate as an optimization problem. The problem is unfortunately nonconvex and cannot be efficiently solved. To overcome the difficulty, we invoke the uplink-downlink duality to transform the problem back and forth between uplink and downlink communications. An efficient, iterative waterfilling based algorithm is then proposed to yield achievable rates with the best possible fairness values. Simulation results show that the proposed approach offers an enormous gain in the achievable sum rates for a wide range of fairness values, when compared to the popular successive zero-forcing DPC-based and block diagonalization based coding schemes. [ABSTRACT FROM AUTHOR]

The explosive growth of Internet-of-Things (IoT) applications such as smart cities and Industry 4.0 have led to drastic increase in demand for wireless bandwidth, hence motivating the rapid development of new techniques for enhancing spectrum utilization needed by new generation wireless communication technologies. Among others, dynamic spectrum access (DSA) is one of the most widely accepted approaches. In this paper, as an enhancement of existing works, we take into consideration of inter-node collaborations in a dynamic spectrum environment. Typically, in such distributed circumstances, intelligent dynamic spectrum access almost invariably relies on self-learning to achieve dynamic spectrum access improvement. Whereas, this paper proposes a DSA scheme based on deep reinforcement learning to enhance spectrum and access efficiency. Unlike traditional Q-learning-based DSA, we introduce the following to enhance the spectrum efficiency in dynamic IoT spectrum environments. First, deep double Q-learning is adopted to perform local self-spectrum-learning for IoT terminals in order to achieve better dynamic access accuracy. Second, to accelerate learning convergence, federated learning (FL) in edge nodes is used to improve the self-learning. Third, multiple secondary users, who do not interfere with each other and have similar operation condition, are clustered for federated learning to enhance the efficiency of deep reinforcement learning. Comparing with the traditional distributed DSA with deep learning, the proposed scheme has faster access convergence speed due to the characteristic of global optimization for federated learning. Based on this, a framework of federated deep reinforcement learning (FDRL) for DSA is proposed. Furthermore, this scheme preserves privacy of IoT users in that FDRL only requires model parameters to be uploaded to edge servers. Simulations are performed to show the effectiveness of theproposed FDRL-based DSA framework. [ABSTRACT FROM AUTHOR]

Real-time systems with strict timing constraints have been widely applied in many fields. The Directed acyclic graph (DAG) task model has been widely studied and applied to model real-time systems with partial parallelism and precedence constraints in each task. Our paper focuses on the worst-case response time (WCRT) analysis of DAG tasks under partitioned scheduling on multiprocessors. We investigate a parallel structure named $Str$ S t r , which helps obtain more accurate analysis results, and propose a new offline scheduling analysis algorithm named reducing repetitive calculation (RRC). Experiments with synthetic workload are conducted to compare the results calculated by RRC and the state-of-the-art, as well as the observed average response time on a real embedded system. Results show that RRC has better performance in terms of analysis accuracy. [ABSTRACT FROM AUTHOR]

The future connectivity landscape, and notably, the 5G wireless systems will feature Ultra-Reliable Low Latency Communication (URLLC). The coupling of high reliability and low latency requirements in URLLC use cases makes the wireless access design very challenging, in terms of both the protocol design and of the associated transmission techniques. This paper aims to provide a broad perspective on the fundamental tradeoffs in URLLC, as well as the principles used in building access protocols. Two specific technologies are considered in the context of URLLC: massive MIMO and multi-connectivity, also termed interface diversity. This paper also touches on the importance of the proper statistical methodology for designing and assessing extremely high-reliability levels. [ABSTRACT FROM AUTHOR]

This paper studies the effectiveness of relaying for interference mitigation in an interference-limited communication scenario. We are motivated by the observation that in a cellular network, a relay node placed at the cell edge observes a combination of intended signal and inter-cell interference that is correlated with the received signal at a nearby destination, so a relaying link can effectively allow the antennas at the relay and at the destination to be pooled together for both signal enhancement and interference mitigation. We model this scenario by a multiple-input multiple-output (MIMO) Gaussian relay channel with a digital relay-to-destination link of finite capacity, and with correlated noise across the relay and destination antennas. Assuming a compress-and-forward strategy with Gaussian input distribution and quantization noise, we propose a coordinate ascent algorithm for obtaining a stationary point of the non-convex joint optimization of the transmit and quantization covariance matrices. For fixed input distribution, the globally optimum quantization noise covariance matrix can be found in closed-form using a transformation for the relay’s observation that simultaneously diagonalizes two conditional covariance matrices by congruence. For fixed quantization, the globally optimum transmit covariance matrix can be found via convex optimization. This paper further shows that such an optimized achievable rate is within a constant additive gap of the MIMO relay channel capacity. The optimal structure of the quantization noise covariance enables a characterization of the slope of the achievable rate as a function of the relaying link capacity. Moreover, this paper shows that the improvement in spatial degrees of freedom by MIMO relaying in the presence of noise correlation is related to the aforementioned slope via a connection to the deterministic relay channel. [ABSTRACT FROM AUTHOR]

This paper provides an analytical performance characterization of both the uplink (UL) and downlink (DL) user-centric network multiple-input multiple-output (MIMO) systems, where a cooperating base station (BS) cluster is formed for each user individually and the clusters for different users may overlap. In this model, cooperating BSs (each equipped with multiple antennas) jointly perform zero-forcing beamforming to the set of single-antenna users associated with them. As compared with a baseline network MIMO system with disjoint BS clusters, the effect of user-centric clustering is that it improves signal strength in both the UL and DL, while reducing cluster-edge interference in the DL. This paper quantifies these effects by assuming that BSs and users form Poisson point processes and by further approximating both the signal and interference powers using Gamma distributions of appropriate parameters. We show that BS cooperation provides significant gain as compared to single-cell processing for both the UL and DL, but the advantage of user-centric clustering over the baseline disjoint clustering system is significant for the DL cluster-edge users only. Although the analytic results are derived with the assumption of perfect channel state information and infinite backhaul between the cooperating BSs, they nevertheless provide architectural insight into the design of the future cooperative cellular networks. [ABSTRACT FROM AUTHOR]

This paper investigates the interference nulling capability of reconfigurable intelligent surface (RIS) in a multiuser environment where multiple single-antenna transceivers communicate simultaneously in a shared spectrum. From a theoretical perspective, we show that when the channels between the RIS and the transceivers have line-of-sight and the direct paths are blocked, it is possible to adjust the phases of the RIS elements to null out all the interference completely and to achieve the maximum $K$ degrees-of-freedom (DoF) in the overall $K$ -user interference channel, provided that the number of RIS elements exceeds some finite value that depends on $K$. Algorithmically, for any fixed channel realization we formulate the interference nulling problem as a feasibility problem, and propose an alternating projection algorithm to efficiently solve the resulting nonconvex problem with local convergence guarantee. Numerical results show that the proposed alternating projection algorithm can null all the interference if the number of RIS elements is only slightly larger than a threshold of $2K(K-1)$. For the practical sum-rate maximization objective, this paper proposes to use the zero-forcing solution obtained from alternating projection as an initial point for subsequent Riemannian conjugate gradient optimization and shows that it has a significant performance advantage over random initializations. For the objective of maximizing the minimum rate, this paper proposes a subgradient projection method which is capable of achieving excellent performance at low complexity. [ABSTRACT FROM AUTHOR]

Recent studies on cloud-radio access networks assume either signal-level or scheduling-level coordination. This paper considers a hybrid coordinated scheme as a means to benefit from both policies. Consider the downlink of a multi-cloud radio access network, where each cloud is connected to several base-stations (BSs) via high capacity links and, therefore, allows for joint signal processing within the cloud transmission. Across the multiple clouds, however, only scheduling-level coordination is permitted, as low levels of backhaul communication are feasible. The frame structure of every BS is composed of various time/frequency blocks, called power-zones (PZs), which are maintained at a fixed power level. This paper addresses the problem of maximizing a network-wide utility by associating users to clouds and scheduling them to the PZs, under the practical constraints that each user is scheduled to a single cloud at most, but possibly to many BSs within the cloud, and can be served by one or more distinct PZs within the BSs’ frame. This paper solves the problem using graph theory techniques by constructing the conflict graph. The considered scheduling problem is, then, shown to be equivalent to a maximum-weight independent set problem in the constructed graph, which can be solved using efficient techniques. This paper then proposes solving the problem using both optimal and heuristic algorithms that can be implemented in a distributed fashion across the network. The proposed distributed algorithms rely on the well-chosen structure of the constructed conflict graph utilized to solve the maximum-weight independent set problem. Simulation results suggest that the proposed optimal and heuristic hybrid scheduling strategies provide appreciable gain as compared with the scheduling-level coordinated networks, with a negligible degradation to signal-level coordination. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel scalable reinforcement learning approach for simultaneous routing and spectrum access in wireless ad-hoc networks. In most previous works on reinforcement learning for network optimization, the network topology is assumed to be fixed, and a different agent is trained for each transmission node—this limits scalability and generalizability. Further, routing and spectrum access are typically treated as separate tasks. Moreover, the optimization objective is usually a cumulative metric along the route, e.g., number of hops or delay. In this paper, we account for the physical-layer signal-to-interference-plus-noise ratio (SINR) in a wireless network and further show that bottleneck objective such as the minimum SINR along the route can also be optimized effectively using reinforcement learning. Specifically, we propose a scalable approach in which a single agent is associated with each flow and makes routing and spectrum access decisions as it moves along the frontier nodes. The agent is trained according to the physical-layer characteristics of the environment using a novel rewarding scheme based on the Monte Carlo estimation of the future bottleneck SINR. It learns to avoid interference by intelligently making joint routing and spectrum allocation decisions based on the geographical location information of the neighbouring nodes. [ABSTRACT FROM AUTHOR]

The universal filtered multicarrier (UFMC) modulation is among the most considered solutions for the realization of beyond orthogonal frequency division multiplexing (OFDM) air interfaces for future wireless networks. This paper focuses on the design and analysis of a UFMC transceiver equipped with multiple antennas and operating at millimeter-wave carrier frequencies. This paper provides the full mathematical model of an MIMO-UFMC transceiver, taking into account the presence of hybrid analog/digital beamformers at both ends of the communication links. Then, several detection structures are proposed, both for the case of single-packet isolated transmission and for the case of multiple-packet continuous transmission. In the latter situation, this paper also considers the case in which no guard time among adjacent packets is inserted, trading off an increased level of interference with higher values of spectral efficiency. At the analysis stage, several considered detection structures and transmission schemes are compared in terms of bit-error rate, root-mean-square error, and system throughput. The numerical results show that the proposed transceiver algorithms are effective and that the linear minimum mean-square error (MMSE) data detector is capable of well managing the increased interference brought by the removal of guard times among consecutive packets, thus yielding throughput gains of about 10%–13%. The effect of phase noise at the receiver is also numerically assessed, and it is shown that the recursive implementation of the linear MMSE exhibits some degree of robustness against this disturbance. [ABSTRACT FROM AUTHOR]

In wireless networks, the link connectivity may be intermittent due to shadowing, burstiness of data arrival, or uncoordinated resource allocation. In this paper, we model the intermittence of links as Bernoulli distributed random channel states, termed intermittence channel states, and study the impact of the corresponding channel state information at the transmitter (CSIT) in a two-user Gaussian broadcast channel (BC). Moreover, due to the heterogeneous timeliness of intermittence channel states, the CSIT considered in this paper is hybrid. More specifically, the CSIT of each link can be perfectly (causally or non-causally) available, delayed, or not available. When the links are connected, we adopt a general setting that the received signal-to-noise ratios can be different. Our contribution is the characterization of the capacity regions of intermittent Gaussian BC to within bounded gaps for all combinations of hybrid CSIT, except for scenario DN (delayed CSIT of receiver 1, no CSIT of receiver 2). For scenario DN, we propose an opportunistic physical layer network coding scheme that achieves a strictly larger degree-of-freedom (DoF) region than the no-CSIT DoF region. As a corollary, single-user CSIT is able to increase the sum DoF for intermittent Gaussian BC (also the capacity region for the erasure BC, as a by-product). This result is in sharp contrast to the recent negative result by Davoodi and Jafar, where it is shown that for fast-fading multiple-input single-output BC with continuous channel states, single-user CSIT does not help at all in terms of sum DoF. [ABSTRACT FROM AUTHOR]

This paper presents the research and implementation of a China Digital Radio (CDR) experimental network in Hubei, China with two FM-CDR transmitting stations and four FM-band channels. To study the coverage discontinuity problem in a large service area, the experimental network employs an intelligent networking solution that incorporates multiple service channels carrying Broadcast and Data Services (BADS) and a Common-Regional-Information Channel (CRIC) carrying both service data and system information. The electronic service guide (ESG) carried by CRIC can inform the receivers about the available contents from current and adjacent stations, which can significantly improve the service quality in the overlapping areas, especially under mobile reception environment. Two RF tuners are used in the receiving terminals to access the CRIC, and the BADS channel, respectively. This paper first presents the frequency analysis and coverage tests of the experimental network, and then summarizes the coverage performances with different transmission parameter combinations. The goal is to gain experience in frequency planning, coverage prediction, as well as supportable services of CDR digital audio broadcasting. [ABSTRACT FROM AUTHOR]

The state-dependent Gaussian interference channel (IC) and Z-IC are investigated, in which two receivers are corrupted by the same but differently scaled states. The state sequence is noncausally known at both transmitters, but not known at either receiver. Three interference regimes are studied, i.e., the very strong, strong, and weak regimes. In the very strong regime, the capacity region is characterized under certain channel parameters by designing a cooperative dirty paper coding between the two transmitters to fully cancel the state. In the strong regime, points on the capacity region boundary are characterized under certain channel parameters by designing an achievable scheme based on rate splitting, layered dirty paper coding, and successive state cancellation. In the weak regime, the sum capacity is obtained by independent dirty paper coding at two transmitters. For all the above regimes, the capacity achieves that of the IC/Z-IC without state. Comparison between the state-dependent regular IC and the Z-IC suggests that even with one interference-free link, the Z-IC does not necessarily perform better, because dirty paper coded interference in the regular IC facilitates to cancel the state through the cooperative dirty paper coding between the transmitters. [ABSTRACT FROM AUTHOR]

This paper studies the outage capacity of a network consisting of a multitude of heterogeneous mobile users and operating according to the classical opportunistic beamforming framework. The base station is located at the center of the cell, which is modeled as a disk of finite radius. The random user locations are modeled using a homogeneous spatial Poisson point process. The received signals are impaired by both fading and location dependent path loss. For this system, we first derive an expression for the beam outage probability. This expression holds for all path loss models that satisfy some mild conditions. Then, we focus on two specific path loss models (i.e., an unbounded model and a more realistic bounded one) to illustrate the applications of our results. In the large system limit, where the cell radius tends to infinity, the beam outage capacity and its scaling behavior are derived for the selected specific path loss models. This paper also studies opportunistic schemes that achieve fairness among the heterogeneous users. Numerical evaluations are performed to give further insights and to illustrate the applicability of the outage capacity results even to a cell having a small finite radius. [ABSTRACT FROM PUBLISHER]

We investigate the state-dependent Gaussian wiretap channel with noncausal channel state information at the transmitter (GWTC-N-CSIT), and explore whether three strategies (i.e., taking action on the state, legitimate receiver’s channel output feedback, and combining the former two strategies together) help to enhance the secrecy capacity of the GWTC-N-CSIT. To be specific, we first determine the secrecy capacity of the GWTC-N-CSIT with noiseless feedback. Next, we derive lower and upper bounds on the secrecy capacity of the GWTC-N-CSIT with action-dependent state. Finally, we derive lower and upper bounds on the secrecy capacity of the GWTC-N-CSIT with both action-dependent state and noiseless feedback, and show that these bounds meet for a special case. Numerical results of this paper indicate that all three strategies enhance the secrecy capacity of the GWTC-N-CSIT. The study of this paper offers new options for enhancing the secrecy rates of the state-dependent wiretap channel models. [ABSTRACT FROM AUTHOR]

In this paper, multihop device-to-device (D2D) communications for cell coverage extension are studied. An in-band underlay D2D mode is considered, and the aim is to satisfy the signal-to-noise-ratio requirements for pre-allocated resource blocks (RBs) on the downlink connections, the signal-to-interference-plus-noise-ratio requirements on pre-allocated RBs for every D2D sidelink connection, and a maximum allowable interference at the base station receiver on all uplink RBs. Power control and routing are performed to minimize the expended user equipment energy in the system while meeting these requirements. An optimization problem is formulated that turns out to be a mixed-integer nonlinear program, which is solved using the generalized Benders decomposition (GBD). The GBD breaks down the formulation into a master sub-problem, an auxiliary sub-problem, and a feasibility sub-problem. In this paper, we focus on finding efficient solution methods for the relaxed version of the master sub-problem that is responsible for generating lower bounds on the optimal objective function. Also, an efficient solution technique for the feasibility sub-problem is proposed. Furthermore, a benchmark disjoint scheme for the same problem is proposed, which performs routing and power control separately. The simulations are conducted to compare the performance of both schemes, which show the superiority of joint routing and power control scheme. [ABSTRACT FROM AUTHOR]

In this paper, we analyze the sum rate performance of multi-user multiple-input-multiple-output (MU-MIMO) systems, with a finite constellation phase-shift keying (PSK) input alphabet. We analytically calculate and compare the achievable sum rate in three downlink transmission scenarios: 1) without precoding; 2) with zero forcing (ZF) precoding; and 3) with closed form constructive interference (CI) precoding technique. In light of this, new analytical expressions for the average sum rate are derived in the three cases, and Monte Carlo simulations are provided throughout to validate the analysis. Furthermore, based on the derived expressions, a power allocation scheme that can ensure fairness among the users is also proposed. The results in this work demonstrate that the CI strictly outperforms the other two schemes, and the performance gap between the considered schemes increases with the increase in MIMO size. In addition, the CI provides higher fairness and the power allocation algorithm proposed in this paper can achieve maximum fairness index. [ABSTRACT FROM AUTHOR]

In this paper, a general framework of constructing the optimal frequency-hopping sequence (FHS) sets is presented based on the designated direct product. Under this framework, we obtain infinitely many new optimal FHS sets by combining some one-coincide (OC) sequence sets that are newly constructed in this paper with some known optimal FHS sets. Our constructions are also based on extension method. However, our constructions give new and flexible parameters due to the free choice of OC sequence set. As a result, our constructions allow a great flexibility of choosing parameters of FHS sets for a given frequency-hopping spread spectrum system. [ABSTRACT FROM AUTHOR]

Armature-rail contact performance determines contact resistance between the armature and rail in electromagnetic launch, and the contact resistance directly affects the efficiency of the launch system. Besides, poor contact performance between the armature and rail will results in erosion, gouging, and other issues in launch. These issues will induce surface damage for the rail, and affect the repetitive launch. So it’s important to improve the armature-rail contact performance. As the characteristics of the rail are relatively stationary in the system, more research was done on the effect of armature characteristics (such as material, shape of the contact, thickness of the neck, and structure of the empennage). In this paper, method of combining ANSYS and pressure test paper was used to study the armature-rail contact performance. The dynamic changing process of the armature-rail contact state was observed by ANSYS, and the final contact state in the case of prepressed experiment was observed by pressure test paper and pressure analysis system. Results from ANSYS and pressure test paper would be comparative analyzed in order to get a more accurate conclusion in the condition of actual experiments. The conclusion of this paper is instructive on optimizing armature design and improving armature-rail contact performance. [ABSTRACT FROM PUBLISHER]

Emerging applications involving device-to-device communication among wearable electronics require gigabits per second throughput, which can be achieved by utilizing millimeter-wave (mmWave) frequency bands. When many such communicating devices are indoors in close proximity, such as in a train, car, or airplane cabin, interference can be a serious impairment. This paper uses stochastic geometry to analyze the performance of mmWave networks with a finite number of interferers in a finite network region. Prior work considered either lower carrier frequencies with different antenna and channel assumptions, or a network with an infinite spatial extent. In this paper, human users not only carry potentially interfering devices, but also act to block interfering signals. Using a sequence of simplifying assumptions, accurate expressions for coverage and rate are developed that capture the effects of key antenna characteristics, such as directivity and gain, and are a function of the finite area and number of users. The assumptions are validated through a combination of analysis and simulation. The main conclusions are that mmWave frequencies can provide gigabits per second throughput even with omni-directional transceiver antennas, and larger, more directive antenna arrays give better system performance. [ABSTRACT FROM PUBLISHER]

This paper considers the uplink performance of a multi-user massive multiple-input multiple-output orthogonal frequency-division multiplexing (MIMO-OFDM) system with mobile users. Mobility brings two major problems to a MIMO-OFDM system: inter carrier interference (ICI) and channel aging. In practice, it is common to allot multiple contiguous subcarriers to a user as well as schedule multiple users on each subcarrier. Motivated by this, we consider a general subcarrier allocation scheme and derive expressions for the ICI power, uplink signal to interference plus noise ratio and the achievable uplink sum-rate, taking into account the ICI and the multi-user interference due to channel aging. We show that the system incurs a near-constant ICI power that depends linearly on the ratio of the number of users per subcarrier to the number of subcarriers per user, nearly independently of how the UEs distribute their power across the subcarriers. Further, we exploit the coherence bandwidth of the channel to reduce the length of the pilot sequences required for uplink channel estimation. We consider both zero-forcing and maximal-ratio combining at the receiver and compare the respective sum-rate performances. In either case, the subcarrier allocation scheme considered in this paper leads to significantly higher sum-rates compared to previous work, owing to the near-constant ICI property as well as the reduced pilot overhead. [ABSTRACT FROM AUTHOR]

The lumbar EMG(Electromyography) can effectively reflect the current activity state of human lumbar muscles; however, cardiac signals in the EMG significantly impacts the accuracy of lumbar EMG analysis. Currently, there are some problems in the research of EMG signal interference removal, such as poor removal effects and low operation efficiencies, which do not meet the requirement of real-time signal processing. To solve this problem, this paper proposes a method for removing ECG(Electrocardiogram) interference from lumbar EMG signals based on signal segmentation and SSA(Singular Spectrum Analysis), which first, reduces the amount of data for SSA by detecting and segmenting the ECG interference signal segments and then separating the ECG signals present in the EMG signals through four steps of embedding, decomposition, grouping and reconstruction using SSA, effectively removing the ECG signals present in the EMG signals. Finally, a complete lumbar surface EMG signal without ECG interference was obtained by using the recombination method. The method not only provides a better removal effect but can also greatly improve the computing efficiency of the algorithm. It was proven that the method can improve the computing efficiency by 50-80%, and for signals with obvious ECG interference, the computing speed of the algorithm can be increased to the millisecond level, thus achieving real-time processing. [ABSTRACT FROM AUTHOR]

In concurrent spectrum sharing scenarios between radars and wireless communication systems, one strict approach to protect the radar from undesired interference is locating the base stations outside a guard (or exclusion) zone of the radar. As a result, users inside that zone experience bad communication coverage. This paper uses Reconfigurable Intelligent Surfaces (RISs) to improve the base station coverage of users in the radar exclusion zone. The paper shows, through analysis and simulation, that joint optimization of base station and RIS locations improves the probability of coverage in the exclusion zone over the shared spectrum without disturbing the radar operation. [ABSTRACT FROM AUTHOR]

Fixed Satellite Services (FSS) used to be alone at the C-Band spectrum in most countries. Since the deployment of 5G in many countries (i.e., 3.3–3.6 GHz), FSS is not the exclusive system in the C-Band anymore. In order to minimize the detrimental interference for the FSS to allowable levels, regional exclusion zones of maximum radiated power in 5G base stations (BS) are proposed and evaluated. In this paper, a measurement campaign has been carried out, and an analysis of the interference has been studied. A filtering model, namely Filter to Remove Broadband Interference 5G (FIREBRING), is proposed and analyzed concerning the carrier-to-noise ratio (C/N). Moreover, this paper focuses on the evaluation of the 5G interference into the FSS. The proposed solution deployed an Low-Noise Block (LNB) with a band frequency of 3.7 to 4.2 GHz to test the satellite down-conversion signal at the receiver. The paper offered a complete analysis of the 5G signal, taking into account the implications of out-of-band emissions, potentially LNB saturation into FSS receiver, and the repercussions of the deployment of the 5G BS active antenna systems. With the LNB and down-converter in place, it can be found that the signal interference between 1.450 GHz and 1.550 GHz, is nearly 18 dB. [ABSTRACT FROM AUTHOR]

As an indispensable use case for the 5G wireless systems on the roadmap, ultra-reliable and low-latency communications (URLLC) is a crucial requirement for the coming era of wireless industrial automation. The key performance indicators for URLLC stand in sharp contrast to the requirements of enhanced mobile broadband: low-latency and ultra-reliability are paramount but high data rates are often not required. This paper aims to develop communication techniques for making a paradigm shift from the conventional human-type broadband communications to the emerging machine-type URLLC. One fundamental task for URLLC is to deliver short commands from a controller to a group of actuators within the stringent delay requirement and with high reliability. Motivated by the factory automation setting in which the tasks are assigned to groups of devices that work in close proximity to each other and can thus form clusters of reliable device-to-device (D2D) networks, this paper proposes a novel two-phase transmission protocol for achieving URLLC. In the first phase, within the latency requirement, the multi-antenna base station (BS) combines the messages of all devices within each group together and multicasts them to the corresponding groups; messages for different groups are spatially multiplexed. In the second phase, the devices that have decoded the messages successfully, herein defined as the leaders, help relay the messages to the other devices in their groups. Under this protocol, we design an innovative leader selection-based beamforming strategy at the BS by utilizing the sparse optimization technique. The proposed strategy leads to a desired sparsity pattern in user activity with at least one leader being able to decode its message in each group in the first phase, thus ensuring full utilization of the reliability enhancing D2D transmissions in the second phase. Simulation results are provided to show that the proposed two-phase transmission protocol considerably improves the reliability of the entire system within the stringent latency requirement as compared with existing schemes for URLLC. [ABSTRACT FROM AUTHOR]

In this paper, we consider routing in random wireless-ad hoc-networks, where each node is equipped with a single antenna. Our analysis uses a proper model of the physical layer together with an abstraction of higher communication layers. We assume that the nodes are distributed according to a Poisson-point-process and consider routing schemes that select the next relay based on the geographical locations, the channel gains of its neighbor nodes and the statistical characterization of all other nodes. While many routing problems are formulated as optimization problems, the optimal distributed solution is rarely accessible. In this paper, we present the exact optimal solution for the scenario analyzed. The optimal routing is given as a maximization of a routing metric, which depends solely on the known partial channel state information and includes an expectation with respect to the interference statistics. The optimal routing scheme is important because it gives an upper bound on the performance of any other routing scheme. We also present sub-optimal routing schemes that only use part of the available knowledge and require much lower computational complexity. Numerical results demonstrate that the performance of the low complexity schemes is close to optimal and outperforms other tested routing schemes. [ABSTRACT FROM PUBLISHER]

In this paper, we consider a new interference problem caused by idle small cells, which have no associated user equipment in ultra-dense small cell long-term evolution (LTE) networks. Specifically, we investigate the effect of idle small cells on the signal to interference and noise ratio (SINR) of the cell-specific reference signal (CRS) and the data signals. We confirm that CRS interference from idle small cells produces uneven interference pattern across CRS and data signals and eventually causes an SINR mismatch between CRS and data signals as well as between data signals with and without CRS symbols. In addition, these phenomena become severe with cell densification. In order to solve this mismatch problem, we propose a simple link adaptation framework, which utilizes clustered CRS assignment and hybrid SINR measurement. The numerical results show that the proposed method improves the average sum throughput compared with the conventional approaches. Overall, this paper sheds new light on investigating and coping with the interference problem coming from idle small cells in future ultra-dense small cell LTE networks. [ABSTRACT FROM PUBLISHER]

Despite the promising high-data rate features of visible light communications (VLC), they still suffer from unbalanced services due to blockages and channel fluctuation among users. This paper introduces and evaluates a new transmission scheme which adopts cooperative non-orthogonal multiple access (Co-NOMA) in hybrid VLC/radio-frequency (RF) systems, so as to improve both system sum-rate and fairness. Consider a network consisting of one VLC access point (AP) and multiple strong and weak users, where each weak user is paired with a strong user. Each weak user can be served either directly by the VLC AP, or via the strong user which converts light information received through the VLC link, and forwards the information to the weak user via the RF link. The paper then maximizes a network-wide weighted sum-rate, so as to jointly determine the strong-weak user-pairs, the serving link of each weak user (i.e., either direct VLC or hybrid VLC/RF), and the power of each user message, subject to user connectivity and transmit power constraints. The paper tackles such a mixed-integer non-convex optimization problem using an iterative approach. Simulations show that the proposed scheme significantly improves the VLC network performance (i.e., sum-rate and fairness) as compared to the conventional NOMA scheme. [ABSTRACT FROM AUTHOR]

In this paper, we present a new and significant theoretical discovery. If the absolute height difference between base station (BS) antenna and user equipment (UE) antenna is larger than zero, then the network performance in terms of both the coverage probability and the area spectral efficiency will continuously decrease toward zero as the BS density increases in ultra-dense networks (UDNs). Such findings are completely different from the conclusions in the existing works, both quantitatively and qualitatively. In particular, this performance behavior has a tremendous impact on the deployment of the 5th-generation UDNs. Network operators may invest large amounts of money in deploying more network infrastructure only to obtain even less network capacity. This paper’s results reveal that one way to address this issue is to lower the BS antenna height to the UE antenna height. However, this requires a revolutionized approach of the BS architecture and deployment, which is also explored in this paper. [ABSTRACT FROM PUBLISHER]

This paper proposes a new paradigm for spectrum sharing between cellular wireless communications (CWC) and radio astronomy systems (RAS). In contrast to the existing paradigm of geographical and spectral isolation between CWC and RAS, this paper develops a three phase spectrum access, which enables geographical and spectral coexistence between CWC and RAS. Shared spectrum access zone (SSAZ) is created around the RAS site and CWC cells within the SSAZ follow the three phase spectrum access scheme while those outside the SSAZ have full spectrum access. In addition, system characteristics-based improved spectrum sharing is developed. Furthermore, a built-in fine tuning mechanism is presented for addressing mismatches between design and practical environments as well as for facilitating service evolutions. Performance evaluation results demonstrate that the proposed paradigm offers 1) certain guaranteed spectrum access to RAS, which is impossible in the existing paradigm, 2) capability to handle higher peak and mean traffics to CWC under spectrum restructuring of both CWC and RAS bands, and 3) overall improved spectrum utilization. [ABSTRACT FROM AUTHOR]

This paper studies the precoder design problem of achieving max-min fairness (MMF) amongst users in multigateway multibeam satellite communication systems with feeder link interference. We propose a beamforming strategy based on a newly introduced transmission scheme known as rate-splitting multiple access (RSMA). RSMA relies on multi-antenna rate-splitting at the transmitter and successive interference cancellation (SIC) at the receivers, such that the intended message for a user is split into a common part and a private part and the interference is partially decoded and partially treated as noise. In this paper, we formulate the MMF problem subject to per-antenna power constraints at the satellite for the system with imperfect channel state information at the transmitter (CSIT). We also consider the case of two-stage precoding which is assisted by on- board processing (OBP) at the satellite. Numerical results obtained through simulations for RSMA and the conventional linear precoding method are compared. When RSMA is used, MMF rate gain is promised and this gain increases when OBP is used. RSMA is proven to be promising for multigateway multibeam satellite systems whereby there are various practical challenges such as feeder link interference, CSIT uncertainty, per-antenna power constraints, uneven user distribution per beam and frame-based processing. [ABSTRACT FROM AUTHOR]