Search

The occurrence of passive intermodulation (PIM) is inevitable in high-power microwave devices. It interferes with wireless communication and radar systems, resulting in severe deterioration of receiving performance. So far, narrowband PIM analyzers have been realized for different business bands. However, they are incapable of testing wideband systems. To solve this problem, rack-mounted analyzers piled with multiple narrowband analyzers were implemented. While such solutions significantly increase the volume, cost, and power consumption, they cannot provide a wide, continuous bandwidth for PIM localizations. Aiming to solve this problem, we propose a novel solution for realizing ultrawideband PIM analyzers. Based on the principle of cooperative radio frequency and baseband (RF-BB) nulling, we demonstrate an experimental prototype working within a continuous frequency band covering three octaves, exhibiting promising potential in PIM testing applications. [ABSTRACT FROM AUTHOR]

A new electromagnetic band gap (EBG) structure based on the soft and hard surfaces for gap waveguide (GW) technology is introduced in this article. The proposed EBG structure consists of a soft surface and a hard surface in parallel with a gap between them, where the ridges/corrugations of the two surfaces are perpendicular to each other or with an angle near 90°. Compared with the contactless bed of nails EBG, the most widely used EBG structure in GW technology, the structural strength of the new EBG structure is increased significantly, which makes it very suited for high-frequency applications. Another advantage is that with the varying of the angle between the ridges/corrugations of the two surfaces, the stopband shifts in a wide frequency band, which makes the stopband tunable after the EBG is fabricated. The stopband performance of the proposed EBG is investigated. Straight and bended groove GWs (GGW) employing this new EBG are designed, manufactured and tested. The isolation performance with different columns of ridges/corrugations is also tested. The measured results show the proposed GGWs have excellent transmission performance. [ABSTRACT FROM AUTHOR]

This letter proposed a combined susceptibility diagram, applicable to investigating and differentiating the inherent mechanism of multipactor in dielectric-loaded microwave devices. This susceptibility diagram consists of average secondary emission yield on the dielectric surface and both the surfaces. Using this diagram, we predict the electron multiplication mechanism in the partially dielectric-loaded parallel-plate waveguide. It is found that the multipactor extinguishing only occurs for a low multipaction rate, while the saturation occurs for a higher multipaction rate. To verify its validity, the dynamic evolution of multipactor is investigated by electrostatic particle-in-cell. A good agreement between simulations and prediction results has been achieved. This susceptibility diagram thus constructed can provide a guidance to clearly identify the condition for multipactor extinguishing or saturation. [ABSTRACT FROM AUTHOR]

This article concentrates on the high-power microwave (HPM) breakdown process and behaviors in air-filled rectangular waveguide under the external dc magnetic field. To solve the persuasive issue, a three-dimensional (3-D) multiphysics model coupling full-wave Maxwell’s equations with plasma fluid equations is established and solved by the spectral-element time-domain (SETD) method. In our simulation, the Galerkin’s method is employed for the space discretization and the central difference scheme is used for the temporal discretization during the SETD process. The numerical results reveal that the external dc magnetic field applied in breakdown volume can significantly enhance the breakdown threshold to suppress the HPM breakdown, which is beneficial for the propagation of HPM pulse in air-filled waveguide. Our research provides theoretical guidance for suppressing the impact of HPM breakdown for HPM devices protection. [ABSTRACT FROM AUTHOR]

The analytical description of dielectric multipactors requires an accurate physical model. In this article, a nonstationary statistical theory for the analysis of single-surface dielectric multipactors is established by defining an emission-to-emission transition rate and involving all the probability densities related to the emitted secondary electrons. Under the same conditions, the fluctuation of electrons in the evolution process of dielectric multipactors was calculated by the proposed theory and simulated by a commercial particle simulation tool developed based on the Monte Carlo analysis. The calculated results comply well with the simulated ones. Our results also indicated that to obtain an adequate accuracy, at least two random variables, the emission velocity and zenith angle, need to be considered. [ABSTRACT FROM AUTHOR]

The aim of this article is to establish a general and practical analytical model of the one-sided multipactor on a dielectric of a metal surface and analyze the resonant multipactor effect for the recent growing interest in spacecrafts. A theoretical multipactor model involving a normal static electric field, a radio frequency (RF) electric field with both tangential and normal components, and the influence of the desorption gas is proposed. The kinetic properties and the resonant condition of the electron are studied by analytical calculations. The results show that the transit time of the electron decreases with the increase in the normal static electric field and the pressure of the desorption gas. The emission phase of the electron is the paramount factor that has a direct influence on the occurrence of the resonant multipactor. If the resonant multipactor effect could appear, the emission phase of the electron should be larger than a critical phase, and the ratio between the amplitude of the normal component of the RF electric field and the normal static electric field should be larger than a specific value as well. [ABSTRACT FROM AUTHOR]

Charging effects of dielectric due to space electron beam irradiation have a huge impact on spacecraft. To understand charging equilibrium characteristics of dielectric under electron beam irradiation, in this paper, we present a novel numerical simulation method for analyzing the secondary electron yield (SEY) based on a charging balance mode. We used the Mott scattering model and the Penn dielectric function (PDF) model to calculate the collisions between incident electrons and material the atoms of material. For internal charge transport, we considered the processes of drift, diffusion, trapping, and neutralization. These were calculated with a finite-difference time-domain (FDTD) method. Based on mechanisms of import–export dynamic charge evolution, charging balance can be categorized into three modes: SE mode, leakage (LE) mode, and cooperation (CO) mode (a combination of the two). In most situations, the SE mode corresponds to the surface charging state, while the LE mode always corresponds to deep charging states. Shortening the distance of free charge transport, a thinner sample is more likely to present as LE mode. Although the surface potential can be enhanced by monotonously increasing the thickness, the total internal charge quantity approaches a local maximum with thickness because of a charging balance mode transformation. In addition, with a larger average density of carriers in the LE mode, the material conductivity is enhanced and the dielectric loss tends to be larger at low frequencies (<103 Hz). The charging balance mode method in this study can also be appropriate to the analyses of altering irradiation parameters and materials intrinsic parameters. [ABSTRACT FROM AUTHOR]

A new kind of contactless electromagnetic bandgap (EBG) structure in the form of interdigital-pin bed of nails is introduced for the first time in this paper. It consists of two metal plates with interdigital-pin bed of nails face to face with each other, where each pin is surrounded by four pins on the other plate. The working mechanism of the interdigital-pin contactless EBG structure is suppressing the modes supported by the parallel plate waveguide (PPW) by loading interdigital pins inside the PPW. The advantage of the interdigital-pin lattice is there is a significant pin gap increase. This lattice makes the minimum pin gap that could be processed by the machining center, after assembling, reduced from the diameter of the milling clutter to its radius. It provides a way to process EBG structures at higher frequency band with the same milling cutter. The cases the pins allocated between the two plates in a random manner are also studied. Compared to its traditional counterpart, the stopband is stable with a small variation. A W-band groove gap waveguide (GGW) prototype with interdigital-pins and a Ka-band GGW with randomly allocated pins are designed, manufactured, and tested. The measured results agree well with the simulation. [ABSTRACT FROM AUTHOR]

The underlying mechanisms of multipactor between dielectric and metal and the discharge threshold of practical dielectric components have been investigated numerically and experimentally in this paper. The reduction in secondary electron yield (SEY) and the change in surface condition are achieved using the microstructure processing technology on both of ferrite dielectric and metal. Combined with the electromagnetic particle-in-cell method, the SEY model fit with the experimental data is utilized to simulate multipactor in three groups of ferrite circulators with different surface conditions. Simulation and experimental results demonstrate that the multipactor threshold of the circulator is increased by a factor of 2 through the SEY reduction on the ferrite and is increased by a factor of more than 8, from 380 W to more than 3400 W, through the SEY reduction on both of the ferrite and the metal. Different multipactor discharge mechanisms, including two-side multipactor with positive charge accumulation, singe-side multipactor with negative charge accumulation, and multipactor suppression effect, exist in circulators with the same physical structure and different surface conditions. [ABSTRACT FROM AUTHOR]

Many radio frequency measurement systems require multicarrier signals with coherent phases between carriers with different frequencies. A typical example is the signal generator which is used in multicarrier multipactor (MM) testing systems. In this paper, we propose a new approach for the generation of coherent multicarrier signals based on a state-of-the-art phase-locked loops technique. Different from existing systems that rely on a heavy use of commercial microwave instruments, this generator can be implemented with on-shelf chips and devices. As an example, an ultrahigh frequency band generator is implemented and how to implement the in-system calibration of this generator in an experimental multipactor testing system is demonstrated. Based on the proposed approach, performing a quantitative experimental research on MM becomes affordable for an ordinary microwave laboratory, which may promote the in-depth experimental study in this area. It can also be used in a wide range of applications such as MIMO and phased array systems. [ABSTRACT FROM AUTHOR]

Passive intermodulation (PIM) potentially occurs in all high-power passive microwave devices. It can severely deteriorate the receiving performance of wireless communication and radar systems. To date, the simultaneous localization of multiple PIM sources in practical microwave devices is still a technical challenge. In this paper, we indicate that if a reference PIM source can be introduced into the standard PIM testing system, and the amplitude and frequency-dependent phase difference between the reference and the real PIM products can be used to construct a k-space multicarrier signal, PIM localization algorithms for both wideband and narrowband devices can be proposed based on the inverse k-space Fourier transform and inverse optimization of the partial multicarrier signal. Simulation and experimental results validate the effectiveness of the proposed approaches. These methods can solve the difficulty of multipoint PIM localization, and can be widely used in the design, production, testing, and troubleshooting of high-power microwave systems. [ABSTRACT FROM AUTHOR]

The newly discovered “long-term” multicarrier multipactors that can be induced by low-energy electric fields potentially threatens the reliability of spaceborne microwave systems. It also causes a new technical challenge to the prediction of the global occurrence threshold of multicarrier multipactors. In this paper, we propose efficient approaches to rapidly compute the fluctuation of space electrons in the evolving process of a multicarrier multipactor, based on which Monte Carlo approaches are developed to efficiently find the global “worst case” waveforms and the occurrence thresholds for both “single-event” and “long-term” multipactors. The proposed approaches can be used for wideband devices, providing an efficient integrated solution for the multicarrier multipactor analysis for practical high-power microwave devices with inhomogeneous field distribution. [ABSTRACT FROM PUBLISHER]

Passive intermodulation (PIM) is one of the major reliability problems in microwave communication systems. In this paper, the PIM interference generated by the metal–insulator–metal (MIM) contact nonlinearity was analytically modeled and experimentally verified. The pressure-dependent nonlinear $I$ – $V$ equations of the MIM contact were derived based on electrical contact theory and verified using a manufactured MIM contact structure. Then a point source model for the PIM product based on the metallic contact nonlinearity was proposed. The PIM product is mainly determined by the contact resistance, surface current density, and nonlinear current coefficient from the model, and in the small contact resistance region, the PIM level decreasing rates are 60, 60, and 20 dB/decade by decreasing the contact resistance, surface current density, and the nonlinear current coefficient, respectively. A designated PIM current source was utilized to verify the relationship. In the end, the PIM equation for the rectangular waveguide connection was derived based on the point source model. This model will provide guidance on low PIM system design. [ABSTRACT FROM PUBLISHER]

Contact nonlinearity is one of the primary sources of passive intermodulation (PIM). Common methods to eliminate the contact nonlinearity are focused on improving the electrical contact. In this letter, the contactless waveguide flange (CWF) based on gap waveguide technology is first applied to solve the PIM problem caused by waveguide connection. A compact folded CWF is proposed for low-frequency applications. The artificial magnetic conductor plate, in the form of a bed of nails, is arranged surrounding the outer surface of the male flange, whereas a waveguide with broader hollow end serves as the female flange. The size of the proposed contactless flange is significantly reduced compared to its planer counterpart. An S-band prototype is designed, manufactured, and measured. Compared to traditional waveguide flange, the measured PIM level achieves a maximum improvement of 30 dB, which is almost unaffected by surface plating materials and connection pressure. [ABSTRACT FROM AUTHOR]