Search

Conventional dual-active-bridge (DAB) dc–dc converters have a limited structure to balance the bipolar voltage level of the bipolar dc distribution system. Therefore, to regulate the bipolar voltage level, additional voltage balancers are needed for the DAB converters, which eventually requires more devices resulting in low power conversion efficiency and low power density. This article proposes an enhanced DAB dc–dc converter that can balance the bipolar voltage level without the additional voltage balancers. The bipolar voltage level can be tightly regulated under entire unbalanced load condition and even when there is no-load at one side of the dc poles. Besides, its zero-voltage-switching capability can be extended to cover the entire load range, including the no-load condition. Furthermore, the proposed converter can be operated by using a simple single phase-shift modulation. Therefore, its control algorithm can be easily implemented in digital controllers. Finally, the theoretical analysis and the effectiveness of the proposed DAB converter are validated by a 3-kW prototype converter. [ABSTRACT FROM AUTHOR]

In this paper, the microcavity effect in quantum dot infrared photodetectors (QDIPs) on a Si substrate, fabricated by means of metal wafer bonding (MWB) and epitaxial lift-off (ELO) processes, was demonstrated by comparing the photocurrent spectrum and the simulated absorption spectrum. Four QDIPs having a different cavity length of 1.7, 2.8, 3, and 3.4 μm were fabricated and compared with simulation based on the finite-difference time-domain method. The resonance peaks were observed in both photocurrent spectrum and absorption spectrum due to the microcavity formed by the bottom mirror of Pt/Au layer and the flat GaAs/air interface. The peak wavelength of the photocurrent spectrum in all four QDIPs on Si samples shows a good agreement with the simulated absorption spectrum. The bias-dependent photocurrent was also measured to study the microcavity effects more in depth. The ratio of the increased photocurrent under bias condition shows higher value in the microcavity QDIPs, showing that the microcavity contributes to generate photocurrent effectively. From these results, we believe that the MWB and ELO could be useful to make the microcavity in many integrated chemical and biosensing application. [ABSTRACT FROM AUTHOR]

This paper proposes an effective test bed for a 380-V dc distribution system using isolated power converters. The proposed test-bed system is composed of a grid-interactive ac–dc converter for regulating the dc-bus voltage, a bidirectional converter for the battery power interface, a renewable energy simulator, dc home appliances modified from conventional ac components, a dc distribution panel board, and its monitoring system. This paper discusses three isolated power converters, i.e., a bidirectional ac–dc converter, a bidirectional dc–dc converter, and a unidirectional dc–dc converter for the effective power interface of a dc bus. These isolated power converters are designed using a dual-active-bridge converter and the resonant topologies of $CLLC$ and $LLC$. The proposed test-bed system was implemented using a 5-kW bidirectional ac–dc prototype converter, a 3-kW bidirectional dc–dc prototype converter, and a 3-kW unidirectional dc–dc prototype converter. Finally, the performance of the test-bed system has been verified using practical experiments of load variations and bidirectional power flow, employing the prototype converters. [ABSTRACT FROM PUBLISHER]

This paper presents a multioutput converter using an asymmetrical pulsewidth modulation half-bridge flyback topology employing a parallel–series-connected transformer. Compared to conventional multioutput topologies, the proposed converter operates using a single-output controller without the need for additional control loops and devices. In order to solve the cross-regulation problem, the output stages of the proposed converter are stacked in series. In addition, the voltage regulation of the proposed multioutput converter is improved through the analysis of its resonant characteristics under load variations and minimizing the secondary conduction loss. The proposed multioutput converter shows excellent performance in terms of its output regulation from no-load to full-load conditions and good cross regulation under high output currents. The design methodology and performance of the proposed converter have been verified through experimentation employing a 110-W (3.3 V/16 A, 5 V/12 A) prototype converter. [ABSTRACT FROM PUBLISHER]

A bidirectional full-bridge CLLC resonant converter using a new symmetric LLC-type resonant network is proposed for a low-voltage direct current power distribution system. This converter can operate under high power conversion efficiency because the symmetric LLC resonant network has zero-voltage switching capability for primary power switches and soft commutation capability for output rectifiers. In addition, the proposed topology does not require any snubber circuits to reduce the voltage stress of the switching devices because the switch voltage of the primary and secondary power stage is confined by the input and output voltage, respectively. In addition, the power conversion efficiency of any directions is exactly same as each other. Using digital control schemes, a 5-kW prototype converter designed for a high-frequency galvanic isolation of 380-V dc buses was developed with a commercial digital signal processor. Intelligent digital control algorithms are also proposed to regulate output voltage and to control bidirectional power conversions. Using the prototype converter, experimental results were obtained to verify the performance of the proposed topology and control algorithms. The converter could softly change the power flow directions and its maximum power conversion efficiency was 97.8% during the bidirectional operation. [ABSTRACT FROM AUTHOR]

A high-efficiency isolated bidirectional ac–dc converter is proposed for a 380-V dc power distribution system to control bidirectional power flows and to improve its power conversion efficiency. To reduce the switches’ losses of the proposed nonisolated full-bridge ac–dc rectifier using an unipolar switching method, switching devices employ insulated-gate bipolar transistors, MOSFETs, and silicon carbide diodes. Using the analysis of the rectifier’s operating modes, each switching device can be selected by considering switch stresses. A simple and intuitive frequency detection method for a single-phase synchronous reference frame-phase-locked loop (SRF-PLL) is also proposed using a filter compensator, a fast period detector, and a finite impulse response filter to improve the robustness and accuracy of PLL performance under fundamental frequency variations. In addition, design and control methodology of the bidirectional full-bridge CLLC resonant converter is suggested for the galvanic isolation of the dc distribution system. A dead-band control algorithm for the bidirectional dc–dc converter is developed to smoothly change power conversion directions only using output voltage information. Experimental results will verify the performance of the proposed methods using a 5-kW prototype converter. [ABSTRACT FROM AUTHOR]