Search

Light emitting diode (LED) lamps with ac-input (50 or 60 Hz) usually require an electrolytic capacitor as the dc-link capacitor in the driver circuit to: 1) balance the energy between the input and output power, and 2) to minimize the low-frequency component of the output ripple across the LEDs. The lifetime of this capacitor, however, is much shorter than that of a LED. To maximize the potential lifetime of the LED lighting system, a new pulsating current driving LED driver that does not require any electrolytic capacitors or complicated control circuits to minimize the low-frequency (i.e., 100 or 120 Hz) output ripple is proposed in this paper. The proposed circuit is simple and a single-switch topology is designed to simplify the controller design. The proposed circuit is able to reduce the energy storage capacitance to a few microfarads range, so that film capacitor can be used to replace the unreliable electrolytic capacitor. The circuit operating principles and its theoretical analysis are provided in this paper. Simulation and experimental results are given on a 9-W LED lamp to highlight the merits of the proposed circuit. [ABSTRACT FROM AUTHOR]

With the global concerns on the issue of how to conserve the limited energy resources, compact fluorescent lamps (CFLs) have been forced in a lot of countries to replace the power-hungry incandescent lamps to reduce the energy cost. However, conventional passive power factor corrected electronic ballasts used in CFLs suffer two major drawbacks: 1) they are unable to achieve close-to-unity power factor and 2) they are unable to provide the same amount of light intensity under fluctuating line voltage. This paper proposed a simple lamp power regulation method for a very high-power factor single-switch electronic ballast, which allows the electronic ballast to maintain almost constant lamp power at its full-power condition for a wide range of the input voltage by controlling the dc-link voltage of the ballast power circuit through duty ratio control. When a TRIAC phase-cut dimmer is used to dim the CFL, the dc-link voltage regulation control loop is deactivated; so that the lamp power decreases accordingly during dimming. The analysis and operating principles of the controller are discussed in this paper. MATLAB, PSIM simulation, and experimental results are provided to highlight the merits of the proposed work. [ABSTRACT FROM AUTHOR]

Although compact fluorescent lamps (CFLs) have been on the market for a long time, many of them do not achieve the same power factor as the incandescent lamps do, which presents a significant problem for the utility with the current widespread use of CFLs for household lightings. A simple single-switch electronic ballast with passive valley-fill power factor correction is proposed in this paper for CFL application. The proposed single-switch ballast circuit is able to achieve zero current switching to maximize the circuit efficiency. A simple feedback circuit with duty ratio control is also proposed to improve the high lamp current crest factor caused by the valley-fill circuit. Detailed descriptions and analysis of the circuit operating principles are provided in this paper. Simulation and experimental results are given on a 13-W CFL tube from Osram Sylvania to highlight the merits of the proposed work. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel multifunctional controller for a dimmable high-power-factor single-switch electronic ballast that can be used with standard phase-cut dimmers. Conventional dimmable electronic ballasts lack the ability to 1) provide smooth dimming and maintain high power factor when phase-cut dimmers are used and 2) regulate the lamp power when the input line voltage varies. A digital controller with multiple control functions is proposed in this paper. The proposed controller allows high power factor to be achieved by controlling the duty cycle during dimming with standard phase-cut dimmers. On the other hand, when dimming is not required, the lamp power is regulated through the regulation of the dc-link voltage. Additional control functions, such as lamp low-power cutoff operation, and protection function are also implemented inside the digital controller. The descriptions of the controller operating principles and its logic flow diagrams are provided in this paper. PSIM simulation and experimental results are provided on a 13-W compact fluorescent lamp to highlight the merits of the proposed work. [ABSTRACT FROM AUTHOR]

A novel dimmable high-power-factor compact fluorescent lamp (CFL) electronic ballast that is compatible with standard incandescent lamp dimmers is proposed in this paper. In the proposed system, the dimming controller uses the phase angle of the dimmer as the input feedforward parameter for the duty ratio control of the switch in the power circuit. As a result, a wide range of light output can be achieved with a small range of phase angles of the phase-cut dimmer. The ballast power circuit is a single-switch single-stage resonant inverter, which is essentially a fusion of a SEPIC converter and a single-switch current-fed inverter. Detailed operating principles of the proposed system will be discussed in this paper. System stability analysis that includes the effects of the phase-cut dimmer is also provided. Experimental results are given for a 13-W CFL to demonstrate and highlight the merits of the proposed work. [ABSTRACT FROM AUTHOR]

A novel single-stage single-switch electronic ballast topology with a unity power factor is presented in this paper. The proposed circuit consists of an integrated buck–boost stage that operates in the discontinuous conduction mode to provide a high power factor and a single-switch current-fed resonant inverter to stabilize the lamp current. The proposed topology presents a low cost and compact electronic ballast design method. The detailed descriptions of the circuit's operating principles are provided in this paper. The design equations and mathematical analysis regarding the proposed circuit are discussed in this paper. The proposed ballast has been tested with an 18-W compact fluorescent lamp, and the experimental results confirmed that a very high power factor of 0.995 and an efficiency of 83.4% have been achieved. [ABSTRACT FROM PUBLISHER]

A very high power factor electronic ballast that uses a single switch in the power circuit is proposed in this paper for compact fluorescent lamps (CFLs). The proposed power circuit is designed by integrating a SEPIC power factor corrector with a novel single-switch current-fed resonant inverter. The advantage of this single-switch electronic ballast is that it greatly simplifies the gate-drive circuit design due to the elimination of isolation devices that are otherwise required in the conventional half-bridge totem pole configuration. This topology features a reduction of at least two switches in the power stage compared to conventional two-stage approach for high-power-factor electronic ballasts. In addition, the proposed circuit is also able to achieve close-to-unity power factor by operating the integrated SEPIC power factor corrector in discontinuous conduction mode. The conduction loss of the switch in the proposed circuit is also significantly reduced compared to the conventional class-E single-switch resonant inverter. Experimental results are provided to justify all the theoretical analysis and highlight the features of the proposed circuit on a 13-W CFL. [ABSTRACT FROM AUTHOR]

A single-stage dimmable electronic ballast with very high power factor and high efficiency is presented in this paper. A compact lamp power circuit is designed by integrating a buck-boost power factor corrector with a current-fed resonant inverter. This integration produces a single power-processing unit that minimizes the number of circuit components. The proposed resonant inverter reduces the circulating current in the resonant tank and allows simple gate drivers to be used so that isolation devices can be eliminated. With the buck-boost stage operating in the discontinuous conduction mode (DCM), a close-to-unity power factor is achieved for different lamp-power conditions. A small-signal analysis is presented, and a simple variable frequency controller is developed using the modified 555 timer to provide dimming operations. Simulation and experimental waveforms are provided to highlight the merits of the proposed circuit for a 40-W compact fluorescent lamp. [ABSTRACT FROM AUTHOR]

Resonant inverters are connected to a high-frequency ac (HFAC) bus, where power is delivered to different locations for points-of-use power management. Such a power distribution system subjects to more perturbations and load uncertainties than inverters operating with single load. A novel voltage control method is proposed in this paper for a high-frequency full-bridge resonant inverter with series-parallel resonant tank. A modified one-cycle controlled phase-shift modulation is proposed to effectively compensate the input line variations. The uncertainty model of the high frequency resonant inverter is developed and analyzed with the resonant circuit component tolerance, input line and load variations taken into design considerations. The voltage feedback controller is designed based on the H∞ robust control theory and is implemented with analog discrete devices. The proposed control scheme has the advantages of fast response for both input line and load perturbations. It also ensures a wide range of system stability and guarantees robustness of the power converter. Both simulations and experimental results are provided to verify with the theoretical analysis through an experimental prototype of a full-bridge resonant inverter with an output power of 150-W operating at 1 MHz and an output voltage of 28 V (rms). [ABSTRACT FROM AUTHOR]