Search

The lack of turn-off ability makes the spark gap-based Marx generator uncontrollable in terminating the output pulse. In addition, there are some limitations for rise time and voltage gain improvements in the conventional critically-damped Marx design. In this paper, an efficient over-damped design of Marx circuit is proposed, which leads to a shorter rise time as well as a larger voltage gain. A chopping magnetic switch is employed to achieve the desired values of the fall time and full width at half maximum (FWHM). Moreover, adding a DC bias circuit to the magnetic switch provides the ability to adjust the pulse FWHM parameter. Therefore, an output pulse with a shorter rise time, larger voltage gain, and controllable FWHM is achieved. The finite element method is utilized to simulate the structures, and the proposed scheme is evaluated by practical experiments. [ABSTRACT FROM AUTHOR]

The limited value of the insolated-gate bipolar transistors (IGBTs) blocking voltage is an important issue for applying these devices to the high-voltage power converters. An effective solution is to use a series configuration of these devices in order to achieve higher voltage ratings in addition to save the interesting features such as fast rising time. To reach this goal, acceptable equal voltage sharing for the IGBTs are provided by the series stacking schemes in the normal operation. However, a considerable difference in their voltage level will be occurred in the short-circuit condition. Although the IGBT can withstand the short-circuit current in a defined time, the occurred high voltage stress for the IGBT is fatal in such condition. To solve the mentioned problem, this paper proposes a short-circuit protection system suitable for the series stacked IGBTs. Using this proposal, the safe voltage level for IGBTs as well as the adequate time for the performance of the detection and elimination of the short-circuit fault will be provided. Each IGBT can have a different short-circuit current in the active region since the proposed scheme makes the IGBTs independent in terms of the current in the series structure. An external resistor added to the IGBTs emitter improves the equality of the IGBTs short-circuit currents and consequently their voltage sharing. This resistor controls the system short-circuit current by changing the operating point of IGBTs in active region in the short-circuit fault. The experimental and simulation results show that the safe condition is provided for the IGBTs under the short-circuit fault. [ABSTRACT FROM PUBLISHER]

The amount of stored energy is an important issue in the low-droop and high-precision pulse generation. Pulse forming network (PFN) simulating an open-ended transmission line seems to be useful due to its minimum stored energy. The drawbacks of the PFN include low-output pulse quality and constant pulsewidth, which limit their applications. Another limitation of generating rectangular pulses using PFN is that half of the charged voltage appears in the output when delivering the entire stored energy to the matched load. This paper proposes a structure of PFN-based pulse generator that overcomes the above-mentioned limitations. For continuous pulsewidth adjustment, a lossless scheme is presented. By increasing the ratio of the load magnitude to the characteristic impedance, the amplitude of the output pulse voltage would be approximately equal to that of the charged voltage. Therefore, the semiconductor switches can be utilized in the PFN pulse generator easily. In addition, the pulse quality is enhanced and faster rising time is obtained in comparison with the conventional PFNs. In this proposal, the stored energy quantity is limited to three times the energy needed for the output pulse in the case of RL=10Z0 . To verify the proposed structure, a prototype is simulated using PSPICE software, and the experimental results are presented. [ABSTRACT FROM AUTHOR]

Reliability of the power distribution unit (PDU) is very important in electrical systems. Since any failure in this unit leads to system failure. A commonly used method for increasing the reliability of a dc PDU is using the redundant modules. If a fault occurs in a voltage regulator of PDU, it is replaced by its redundant module. In conventional redundancy, each dc voltage regulator has its exclusive redundant modules. Therefore, if both a regulator and its redundant modules fail, the system is stopped. It is an important drawback since the exclusive redundant modules of other voltage regulators may not be used, but, the PDU cannot use them instead of faulty regulators. In this paper, the application of the nonexclusive redundant regulators is presented for solving this problem. In the proposed method, dc power distribution unit consists of a number of redundant modules, which can be adjusted to a desired voltage and can be used instead of faulty regulators. An analysis based on Markov model is presented to compare reliability of the proposed structure with the conventional structure presuming a variable failure probability. Theoretical study indicates more reliable operation of the proposed PDU structure than the conventional structure. Experimental results are presented to show practical considerations of the proposed structure and its proper performance. [ABSTRACT FROM AUTHOR]