Search

The adaptive sliding-mode control of a high efficiency non-isolated buck-boost converter based on Zeta converter is presented. The converter has a dc gain higher than that of the Zeta converter and is a sixth-order system. The controller uses the inductor current error and a proportional term to generate the control action. The reference inductor current is first calculated using the estimated load conductance obtained from an adaptation algorithm. The proposed and existing sliding-mode controllers are closely related under certain conditions. The stability analysis of the closed-loop system is performed and sheds light on the controller’s effectiveness. Experimental results are given to validate the theory.

By the negative influence of parasitic parameters from the components, the voltage step-up capacity of basic dc-dc converters is limited at extremely high duty cycle. Which makes the traditional dc-dc converters are difficult to be applied to renewable energy generation systems such as fuel cell and photovoltaic (PV) systems. In this study, a single-switch high step-up Zeta converter is proposed based on the basic Zeta converter and corresponding coat circuit. By using the coat circuit, the proposed converter not only can achieve higher voltage gain, but also acquire lower voltage stress on the semiconductor devices. Therefore, the devices with lower conduction resistances can be used to improve the efficiency. Furthermore, the coat circuit is composed of passive components, which does not change the continuous output current characteristic of the basic Zeta converter. And the proposed converter has only one active switch, the drive and control circuits are simple. The operation principle and the performance analysis of the proposed Zeta converter are described in detail, and a 300 W closed-loop experimental prototype has been developed for verification.

This article presents a semiresonant half-bridge zeta (HBZ) converter for high-efficiency power supply. Since the proposed converter utilizes a primary inductor and secondary capacitor as a resonant tank, it can make a resonant operation during the on-state of a low-side primary switch. Therefore, the proposed converter can effectively reduce turn-off currents of the low-side primary switch and the secondary diode without any additional component and control scheme, which decreases turn-off switching loss and reverse-recovery loss. Moreover, the proposed converter can maintain advantages of the conventional HBZ converter such as high input/output (I/O) voltage gain and wide zero-voltage-switching (ZVS) range with the proposed design procedure. As a result, the proposed converter can improve its efficiency over the entire load conditions compared to the conventional HBZ converter. A 250 W, 300-400 V input, and 56 V output prototype has been built and tested to verify the effectiveness of the proposed converter.

To enhance the photovoltaic (PV) power-generation conversion, maximum power point tracking (MPPT) is the foremost constituent. This article introduces an adaptive neuro-fuzzy inference system-particle swarm optimization (ANFIS-PSO)-based hybrid MPPT method to acquire rapid and maximal PV power with zero oscillation tracking. The inverter control strategy is implemented by a space vector modulation hysteresis current controller to get quality inverter current by tracking accurate reference sine-shaped current. The ANFIS-PSO-based MPPT method has no extra sensor requirement for measurement of irradiance and temperature variables. The employed methodology delivers remarkable driving control to enhance PV potential extraction. An ANFIS-PSO-controlled Zeta converter is also modeled as an impedance matching interface with zero output harmonic agreement and kept between PV modules and load regulator power circuit to perform MPPT action. The attainment of recommended hybrid ANFIS-PSO design is equated with perturb and observe, PSO, ant colony optimization, and artificial bee colony MPPT methods for the PV system. The practical validation of the proposed grid-integrated PV system is done through MATLAB interfaced dSPACE interface and the obtained responses accurately justify the proper design of control algorithms employed with superior performance.

In this paper, a new transformerless buck–boost converter based on a ZETA converter is introduced. The proposed converter has the ZETA converter advantages, such as buck–boost capability, input-to-output dc insulation, and continuous output current. The suggested converter voltage gain is higher than the classic ZETA converter. In the presented converter, only one main switch is utilized. The proposed converter offers low voltage stress of the switch; therefore, the low on -state resistance of the main switch can be selected to decrease the losses of the switch. The presented converter topology is simple; hence, the control of the converter is simple. The converter has the continuous output current. The mathematical analyses of the presented converter are given. The experimental results confirm the correctness of the analysis.

The purpose of this paper is to guide electrical engineering students from analysing basic DC-DC converter topologies to more advanced topologies. Textbooks and free online papers include the derivation of second order DC-DC topologies such as buck, boost and buck-boost, while fourth order such as the Zeta converter are not as readily available as open knowledge online. This paper provides a detailed derivation of the Zeta converter topology in continuous conduction mode (CCM), it presents an example of component sizing and verifies the design by simulation in LTspice.

In this paper, a new soft-switching Zeta converter with an asymmetrical pulsewidth modulation (PWM) control is proposed. The proposed Zeta converter has the features of constant frequency operation, zero voltage switching (ZVS), and low voltage stress on the active switches. Moreover, it can achieve high power density, high efficiency, low switching loss, and low component count, which make converter operation at low to medium power level feasible. Operational principle of the Zeta converter is presented in detail, and a specific example is designed and implemented to verify its feasibility.