Search

Based on three-level exciton model, the enhanced photonic microwave signal generation by using a sole excited-state (ES) emitting quantum dot (QD) laser under both optical injection and optical feedback is numerically studied. Within the range of period-one (P1) dynamics caused by the optical injection, the variations of microwave frequency and microwave intensity with the parameters of frequency detuning and injection strength are demonstrated. It is found that the microwave frequency can be continuously tuned by adjusting the injection parameters, and the microwave intensity can be enhanced by changing the injection strength. Moreover, considering that the generated microwave has a wide linewidth, an optical feedback loop is further employed to compress the linewidth, and the effect of feedback parameters on the linewidth is investigated. It is found that with the increase of feedback strength or delay time, the linewidth is evidently decreased due to the locking effect. However, for the relatively large feedback strength or delay time, the linewidth compression effect becomes worse due to the gradually destroyed P1 dynamics. Besides, through optimizing the feedback parameters, the linewidth can be reduced by up to more than one order of magnitude for different microwave frequencies. [ABSTRACT FROM AUTHOR]

A setup is described with which the spontaneous Raman scattering rate from pressurized gas samples is greatly enhanced inside a near-concentric optical cavity. The pump source is a high power multimode semiconductor laser diode that receives optical feedback from the cavity by way of a volume Bragg grating, resulting in a linewidth of 80 pm and circulating power close to 100 W. Under pressurization (up to 8 bar) a limit of detection below 100 parts-per-billion was obtained for gaseous hydrogen, measured in ambient air and in breath. Furthermore, isotopic trace detection is demonstrated by headspace measurements of semiheavy water. [ABSTRACT FROM AUTHOR]

Realizing quasistatic processes in finite times requires additional control parameters to keep the system in instantaneous equilibrium (ieq). However, the finite-rate ieq transition of the reverse process is not just the time-reversal of the ieq forward process due to the odd-parity of controlling parameters. We theoretically show a work relation that the dissipated work of the ieq transition of the forward process is the same as that of the corresponding reverse process. The work relation can be interpreted as a generalization of equilibrium (quasistatic) processes. The work relation and the associated statistics of nonequilibrium work are experimentally confirmed in three different Brownian systems: the time-varying harmonic and non-harmonic potentials and the Brownian harmonic transport, which are manipulated by the optical feedback trap. [ABSTRACT FROM AUTHOR]

The estimation of self-mixing interferometry (SMI) parameters such as optical feedback factor C and linewidth enhancement factor is essential to self-mixing (SM) displacement sensors with sub-wavelength resolution. We propose a new method, which is a very simple and fast method to estimate C and when C > 1 based on an analysis of self-mixing signals (SMSs) in a laser diode. The proposed method is extremely simple, because it takes advantage of analytic relations which enable one to obtain C and from the simple algebraic operations of the data from SMSs. The simplicity of the method is a great help to developing a compact and low-cost self-mixing (SM) displacement sensor with sub-wavelength resolution which cannot ensure complex operation such as optimization. And the proposed method is highly effective in developing real-time and fast algorithm for the C estimation. This method is applicable when the sensor operates under a moderate or strong feedback regime. The estimation accuracy of C and are comparable to the results of Yu et al 2004 IEEE Photon. Technol. Lett. 16 990–2; Zabit 2010 PhD Thesis Toulouse; and Fan 2011 MS Thesis University of Wollongong, respectively, and the estimation time of the C parameter is over 30 times faster than Zabit and Fan. [ABSTRACT FROM AUTHOR]

We have employed an optical feedback circuit in an organic light-emitting diode (OLED) lighting system to ensure uniform light output across large-area OLED lighting tiles. In a lighting system with several large-area OLED lighting tiles involved, the panel aging (luminance decrease) may appear differently in each, resulting in a falling-off in lighting quality. To tackle this, light output from each OLED tile is monitored by the optical feedback circuit that consists of a photodetector, I–V converter, 10-bit analogue–digital converter (ADC), and comparator. A photodetector mounted on a glass side generates a feedback signal (current) by detecting side-emitting OLED light. To monitor bottom-emitting output light by detecting side-emitting OLED light, a mapping table between the ADC value and the luminance of bottom emission has been established. If the ADC value is lower or higher than the reference one corresponding to the target luminance of OLED tiles, a micro controller unit adjusts the pulse width modulation used for the control of the power supplied to OLED tiles in such a way that the ADC value obtained from optical feedback is the same as the reference one. As a result, the target luminance of each individual OLED tile is kept unchanged. With the optical feedback circuit included in the lighting system, we have observed less than 2% difference in relative intensity of neighboring OLED tiles. [ABSTRACT FROM AUTHOR]

An optical device, consisting of a multi-mode Fabry-Pérot laser diode (MMFP-LD) with two-stage optical feedback, is proposed and experimentally demonstrated. The results show that the single-mode output with side-mode suppression ratio (SMSR) of ~21.7 dB is attained by using the first-stage feedback. By using the second-stage feedback, the SMSR of single-mode operation could be increased to ~28.5 dB while injection feedback power of -29dBm is introduced into the laser diode. In the case of up to -29dBm feedback power, the outcome SMSR is rapidly decayed to a very low level so that an obvious multi-mode operation in the output spectrum could be achieved at the feedback power level of -15.5 dBm. Thus, a transition between single- and multi-mode operations could be flexibly controlled by adjusting the injected power in the second-stage feedback system. Additionally, in the case of injection locking, the outcome SMSR and output power at the locked wavelength are as high as ~50 dB and ~5.8 dBm, respectively. [ABSTRACT FROM AUTHOR]

The birefringence optical feedback with a folded cavity in HeNe laser is investigated. A theory model based on the equivalent cavity of the Fabry-Perot interferometer is presented. The phase difference between the two intensities in birefringence feedback is twice the retardation of the wave plate. The phase difference is invariable when the length of the feedback cavity changes. With the adoption of a cube corner prism (CCP) to form a folded cavity, the fringe frequency is doubled, and the resolution of the displacement sensor based on birefringence optical feedback with a folded cavity is improved. A resistance chain of 5-fold subdivision and 4-fold logic subdivision is used as further subdivision. The resolution of ?/80 is obtained eventually; for 632.8nm HeNe laser it is 7.91 nm. The displacement sensor based on birefringence optical feedback with a folded cavity is simple and of high resolution, large measurement range, low cost, and is of great application potential in industry. [ABSTRACT FROM AUTHOR]

The phase tuning characteristics of a double-longitudinal-mode He-Ne laser with optical feedback are demonstrated. The phase behaviors of the two adjacent longitudinal modes are studied with different laser cavity lengths at the weak feedback level, and it is found that the phase difference of the two modes can be 0 to 180&dgr; along with the changing of the length of external cavity. The high-density intensity fringes are obtained with asymmetric feedback cavity at a strong feedback level. In particular, the phase difference is also observed between the two high-density fringes of adjacent modes, which have the potential to develop a direction sensitive laser feedback interferometer with high resolution. A simple theoretical analysis is presented, which fits well with the experimental results. [ABSTRACT FROM AUTHOR]

We demonstrate a simple and robust scheme to measure the relative position of transverse cavity modes with high precision. This is based on robust optical-feedback frequency locking of a diode laser to a cavity resonance. A fraction of the laser power is then frequency shifted and used to re-inject other cavity resonances to obtain their positions relative to the locking resonance. This delivers the Gouy phase shift of the cavity modes with precision down to rad, comparable to previous state of the art based on a more complex setup. This should also be of interest for high precision/accuracy measurement of distance and displacement. [ABSTRACT FROM AUTHOR]

Optomechanics is concerned with the use of light to control mechanical objects. As a field, it has been hugely successful in the production of precise and novel sensors, the development of low-dissipation nanomechanical devices, and the manipulation of quantum signals. Micro- and nano-particles levitated in optical fields act as nanoscale oscillators, making them excellent low-dissipation optomechanical objects, with minimal thermal contact to the environment when operating in vacuum. Levitated optomechanics is seen as the most promising route for studying high-mass quantum physics, with the promise of creating macroscopically separated superposition states at masses of 106 amu and above. Optical feedback, both using active monitoring or the passive interaction with an optical cavity, can be used to cool the centre-of-mass of levitated nanoparticles well below 1 mK, paving the way to operation in the quantum regime. In addition, trapped mesoscopic particles are the paradigmatic system for studying nanoscale stochastic processes, and have already demonstrated their utility in state-of-the-art force sensing. [ABSTRACT FROM AUTHOR]

A liquid refractive index (RI) measurement method based on the double external-cavity laser feedback effect is proposed. The method uses a laser beam to simultaneously enter the top and bottom surfaces of the liquid to be tested, with the light reflected from the two surfaces returning to the laser cavity along the original path, forming a double external-cavity system. When the liquid level rises, the self-mixing interference signal, caused by the optical path from the top and bottom liquid surfaces, superimposes on the tuning intensity of the laser, and the RI of the liquid can be obtained by demodulating the amplitude-frequency feedback tuning curve. This method offers the following innovative performances. Firstly, the structure of the system is simple and the measuring range is large. Secondly, the measurement results can be traced back to one physical quantity, i.e. the RI of air. Thirdly, it has been proved that the laser feedback effect is ubiquitous in all types of lasers, and the change of wavelength does not affect the feedback phenomenon, so that the method is not limited by the type and wavelength of the laser. [ABSTRACT FROM AUTHOR]

We present a combined radio/X-ray analysis of the poorly studied galaxy cluster A2495 (z = 0.07923) based on new EVLA and Chandra data. We also analyze and discuss Hα emission and optical continuum data retrieved from the literature. We find an offset of ∼6 kpc between the cluster brightest cluster galaxy (BCG) (MCG+02-58-021) and the peak of the X-ray emission, suggesting that the cooling process is not taking place on the central galaxy nucleus. We propose that sloshing of the intracluster medium (ICM) could be responsible for this separation. Furthermore, we detect a second, ∼4 kpc offset between the peak of the Hα emission and that of the X-ray emission. Optical images highlight the presence of a dust filament extending up to ∼6 kpc in the cluster BCG and allow us to estimate a dust mass within the central 7 kpc of 1.7 × 105M☉. Exploiting the dust-to-gas ratio and the LHα–Mmol relation, we argue that a significant amount (up to 109M☉) of molecular gas should be present in the BCG of this cluster. We also investigate the presence of ICM depressions, finding two putative systems of cavities; the inner pair is characterized by tage ∼ 18 Myr and Pcav ∼ 1.2 × 1043 erg s−1, the outer one by tage ∼ 53 Myr and Pcav ∼ 5.6 × 1042 erg s−1. Their age difference appears to be consistent with the freefall time of the central cooling gas and with the offset timescale estimated with the Hα kinematic data, suggesting that sloshing is likely playing a key role in this environment. Furthermore, the cavities’ power analysis shows that the active galactic nucleus energy injection is able to sustain the feedback cycle, despite cooling being offset from the BCG nucleus. [ABSTRACT FROM AUTHOR]

We present new, deep observations of the Phoenix cluster from Chandra, the Hubble Space Telescope, and the Karl Jansky Very Large Array. These data provide an order-of-magnitude improvement in depth and/or angular resolution over previous observations at X-ray, optical, and radio wavelengths. We find that the one-dimensional temperature and entropy profiles are consistent with expectations for pure-cooling models. In particular, the entropy profile is well fit by a single power law at all radii, with no evidence for excess entropy in the core. In the inner ∼10 kpc, the cooling time is shorter than any other known cluster by an order of magnitude, while the ratio of the cooling time to freefall time (tcool/tff) approaches unity, signaling that the intracluster medium is unable to resist multiphase condensation on kpc scales. The bulk of the cooling in the inner ∼20 kpc is confined to a low-entropy filament extending northward from the central galaxy, with tcool/tff ∼ 1 over the length of the filament. In this filament, we find evidence for ∼1010M⊙ in cool (∼104 K) gas (as traced by the [O ii]λλ3726,3729 doublet), which is coincident with the low-entropy filament and absorbing soft X-rays. The bulk of this cool gas is draped around and behind a pair of X-ray cavities, presumably bubbles that have been inflated by radio jets. These data support a picture in which active galactic nucleus feedback is promoting the formation of a multiphase medium via uplift of low-entropy gas, either via ordered or chaotic (turbulent) motions. [ABSTRACT FROM AUTHOR]

Neuromorphic photonics is a new paradigm for ultra-fast neuro-inspired optical computing that can revolutionize information processing and artificial intelligence systems. To implement practical photonic neural networks is crucial to identify low-cost energy-efficient laser systems that can mimic neuronal activity. Here we study experimentally the spiking dynamics of a semiconductor laser with optical feedback under periodic modulation of the pump current, and compare with the dynamics of a neuron that is simulated with the stochastic FitzHugh–Nagumo model, with an applied periodic signal whose waveform is the same as that used to modulate the laser current. Sinusoidal and pulse-down waveforms are tested. We find that the laser response and the neuronal response to the periodic forcing, quantified in terms of the variation of the spike rate with the amplitude and with the frequency of the forcing signal, is qualitatively similar. We also compare the laser and neuron dynamics using symbolic time series analysis. The characterization of the statistical properties of the relative timing of the spikes in terms of ordinal patterns unveils similarities, and also some differences. Our results indicate that semiconductor lasers with optical feedback can be used as low-cost, energy-efficient photonic neurons, the building blocks of all-optical signal processing systems; however, the length of the external cavity prevents optical feedback on the chip. [ABSTRACT FROM AUTHOR]

Quantum random numbers are fundamental resources (Rev. Mod. Phys. 89 015004) for the fields of communications and information security. Usually, projective measurements can be applied on a two-qubit entangled state to generate quantum random numbers. However, it cannot certify more than one bit of randomness for one set of measurements. On contrast, non-projective measurements in-principle may be able to generate more random bits, and therefore show some merits among present methods. Here, we report the implementation of a quantum random number generator based on a symmetric informationally complete positive operator-valued measure. In our experiment, we prepare a maximally entangled state of two-qubits through spontaneous parametric down-conversion processes, and observe the violation of Gisin’s elegant Bell inequality with the value of 6.8138 ± 0.0822, exceeding the classical bound of 6. Through randomness extractors, including a Toeplitz extractor and a parallel linear feedback shift register based extractor, we finally extract a random string with an autocorrelation coefficient below 10−3 and the string can pass all randomness tests of the National Institute of Science and Technology (NIST). [ABSTRACT FROM AUTHOR]

We introduce the OSIRIS Lens-Amplified Survey (OLAS), a kinematic survey of gravitationally lensed galaxies at cosmic noon taken with Keck adaptive optics. In this paper, we present spatially resolved spectroscopy and nebular emission kinematic maps for 17 star-forming galaxies with stellar masses 8 < log(M*/M⊙) < 9.8 and redshifts 1.2 < z < 2.3. OLAS is designed to probe the stellar mass (M*) and specific star formation rate (sSFR) range where simulations suggest that stellar feedback is most effective at driving gaseous outflows that create galaxy-wide potential fluctuations, which can generate dark matter cores. We compare our kinematic data with the trend among sSFR, M*, and Hα velocity dispersion, σ, from the Feedback In Realistic Environments (FIRE) simulations. Our observations reveal a correlation between sSFR and σ at fixed M* that is similar to the trend predicted by simulations: feedback from star formation drives star-forming gas and newly formed stars into more dispersion-dominated orbits. The observed magnitude of this effect is in good agreement with the FIRE simulations, in which feedback alters the central density profiles of low-mass galaxies, converting dark matter cusps into cores over time. Our data support the scenario that stellar feedback drives gaseous outflows and potential fluctuations, which in turn drive dark matter core formation in dwarf galaxies. [ABSTRACT FROM AUTHOR]

We present a new method for neutrino-matter coupling in multi-dimensional radiation-hydrodynamic simulations of core-collapse supernovae (CCSNe) with the full Boltzmann neutrino transport. This development is motivated by the fact that accurate conservation of momentum is required for reliable numerical modelings of CCSN dynamics including a recoil of proto-neutron stars (PNSs). The new method is built on a hybrid approach in which we use the energy-momentum tensor of neutrinos to compute the momentum feedback from neutrino to matter in the optically thick region while we employ the collision term in the optically thin region. In this method we utilize a general relativistic description of radiation-hydrodynamics with angular moments, which allows us to evaluate the momentum feedback from neutrino to matter without inconsistency with our Boltzmann solver. We demonstrate that the new method substantially improves the accuracy of linear momentum conservation in our CCSN simulations under reasonable angular resolutions in momentum space, alleviating the difficulty in giving the diffusion limit precisely with the discrete ordinate (Sn) method. It is the first ever demonstration that the PNS kick can be handled directly and properly in multi-dimensional radiation-hydrodynamic simulations with the full Boltzmann neutrino transport. [ABSTRACT FROM AUTHOR]

Laser feedback interference is widely used for displacement measurement of non-cooperative targets due to its ultra-high sensitivity. However, by the same token, laser feedback interferometry (LFI) suffers from multi-channel optical feedback, which compromises measurement stability and accuracy. We perform both simulations and experiments to study the effect of dual-channel optical feedback on LFI systems based displacement measurement. Dual-channel optical feedback interference is the simplest and most representative form of multi-channel feedback interference. We evaluate system performance by varying which is the ratio of feedback level in the primary channel to the one in the secondary channel. The results indicate that the measured displacement curve is a linear line superimposed with nonlinear periodic errors when the target in the primary channel moves linearly and the target in the secondary channel stays stationary. Whereas, the curve is a periodic curve instead of a linear one, for the case when the target in the secondary channel moves linearly while the one in the primary channel stays stationary. Furthermore, the amplitude and shape of the periodic curves also depend on the parameter When is much less than 1, the displacement curve is sinusoidal, whereas the curve has a saw-tooth shape with larger amplitude for close to 1. In view of this situation, a new displacement measurement method, counting the cycles of the periodic displacement curves, is proposed. The current work can provide theoretical and experimental suggestions for improving the performance of existing self-mixing interferometry systems, and implementing ones with multi-channel optical feedback channels. [ABSTRACT FROM AUTHOR]

We derive and analyze an efficient model for reinjection of spatially filtered optical feedback from an external resonator to a broad area, edge emitting semiconductor laser diode (DL). Spatial filtering is achieved by a chirped photonic crystal, with variable periodicity along the optical axis and negligible resonant backscattering. The optimal chirp is obtained from a genetic algorithm, which yields solutions that are robust against perturbations. Exemplary numerical simulations of the composite system with our optoelectronic solver indicate that spatially filtered reinjection can enhance lower-order transversal optical modes in the DL and, consequently, improve the spatial beam quality. [ABSTRACT FROM AUTHOR]

This paper outlines our studies of bifurcation, quasi-periodic road to chaos and other dynamic characteristics in an external-cavity multi-quantum-well laser with delay optical feedback. The bistable state of the laser is predicted by finding theoretically that the gain shifts abruptly between two values due to the feedback. We make a linear stability analysis of the dynamic behavior of the laser. We predict the stability scenario by using the characteristic equation while we make an approximate analysis of the stability of the equilibrium point and discuss the quantitative criteria of bifurcation. We deduce a formula for the relaxation oscillation frequency and prove theoretically that this formula function relates to the loss of carriers transferring between well regime and barrier regime, the feedback level, the delayed time and the other intrinsic parameters. We demonstrate the dynamic distribution and double relaxation oscillation frequency abruptly changing in periodic states and find the multi-frequency characteristic in a chaotic state. We illustrate a road to chaos from a stable state to quasi-periodic states by increasing the feedback level. The effects of the transfers of carriers and the escaping of carriers on dynamic behavior are analyzed, showing that they are contrary to each other via the bifurcation diagram. Also, we show another road to chaos after bifurcation through changing the linewidth enhancement factor, the photon loss rate and the transfer rate of carriers. [ABSTRACT FROM AUTHOR]

We design a hybrid integrated chaotic semiconductor laser with short-cavity optical feedback. It can be assembled in a commercial butterfly shell with just three micro-lenses. One of them is coated by a transflective film to provide the optical feedback for chaos generation while insuring regular laser transmission. We prove the feasibility of the chaos generation in this compact structure and provide critical external parameters for the fabrication by theoretical simulations. Rather than the usual changeless internal parameters used in previous simulation research, we extract the real parameters of the chip by experiment. Moreover, the maps of the largest Lyapunov exponent with varying bias current and feedback intensity Kap demonstrate the dynamic characteristics under different external-cavity conditions. Each laser chip has its own optimal external cavity length (L) and feedback intensity (Kap) to generate chaos because of the different internal parameters. We have acquired two ranges of optimal parameters (L = 4 mm, and L = 5 mm, ) for two different chips. [ABSTRACT FROM AUTHOR]

We report the realization of a deterministic single-atom preparation by the method of all-optical feedback. Using a fast-real-time feedback, the light-induced atom desorption effect and blue detuned light-induced atom collision process can increase a success probability of single-atom preparation up to more than 99%. We investigate the dynamics of loading single atom trapped in a trap with a size of hundreds of micrometers into a pair of microscopic tweezers. The detailed experimental results show that the feedback loading is spatially insensitive, which implies that it is possible to use the feedback protocol to simultaneously implement the loading of large number of qubits arrays. [ABSTRACT FROM AUTHOR]

Cold non-equilibrium atmospheric pressure plasma jets are increasingly applied in material processing and plasma medicine. However, their small dimensions make diagnosing the fluxes of generated species a challenge. Here we report on the detection of the hydroperoxyl radical, HO2, in the effluent of a plasma jet by the use of optical feedback cavity-enhanced absorption spectroscopy. The spectrometer has a minimum detectable absorption coefficient of cm−1 with a 100 second acquisition, equivalent to of HO2 (under ideal conditions). Concentrations in the range of (3.1–7.8) × 1013 cm−3 were inferred in the 4 mm wide effluent of the plasma jet. [ABSTRACT FROM AUTHOR]

In this paper, selective optical feedback is used to investigate the nonlinearity behaviours of a vertical cavity surface emitting laser (VCSEL) with the modulation signal. A single mode VCSEL with both parallel and orthogonal optical feedback (OF) signals modulated at 1 MHz frequency over a range of modulation depth is investigated. We also investigate the nonlinear characteristics of the orthogonal polarization modes XP and YP of the VCSEL by changing the injection current and temperature. The results show an enhancement in the harmonic distortions (HDs) of both XP and YP modes with parallel OF, and the total suppression of HDs with orthogonal OF. We show that for the VCSEL with orthogonal OF, the second and third harmonic components of the XP and YP modes decrease and reach the noise floor level of the output power spectrum. Additionally, peaks of second and third harmonic components change radically when varying the bias current and temperature. The results reveal that orthogonal OF can be employed as a new tool to improve the linear dynamic range and to control the nonlinear characteristics of the VCSEL, thus making these devices a promising optical source in present and future optical communication applications. [ABSTRACT FROM AUTHOR]

Based on a semiconductor laser (SL) with incoherent optical feedback, a novel all-optical scheme for generating tunable and broadband microwave frequency combs (MFCs) is proposed and investigated numerically. The results show that, under suitable operation parameters, the SL with incoherent optical feedback can be driven to operate at a regular pulsing state, and the generated MFCs have bandwidths broader than 40 GHz within a 10 dB amplitude variation. For a fixed bias current, the line spacing (or repetition frequency) of the MFCs can be easily tuned by varying the feedback delay time and the feedback strength, and the tuning range of the line spacing increases with the increase in the bias current. The linewidth of the MFCs is sensitive to the variation of the feedback delay time and the feedback strength, and a linewidth of tens of KHz can be achieved through finely adjusting the feedback delay time and the feedback strength. In addition, mappings of amplitude variation, repetition frequency, and linewidth of MFCs in the parameter space of the feedback delay time and the feedback strength are presented. [ABSTRACT FROM AUTHOR]

We analyze the statistics of photons originating from amplified spontaneous emission generated by a quantum dot superluminescent diode. Experimentally detectable emission properties are taken into account by parametrizing the corresponding quantum state as a multimode phase-randomized Gaussian density operator. The validity of this model is proven in two subsequent experiments using fast two-photon-absorption detection observing second-order equal-time and second-order fully time-resolved intensity correlations on femtosecond timescales. In the first experiment, we study the photon statistics when the number of contributing longitudinal modes is systematically reduced by applying well-controlled optical feedback. In a second experiment, we add coherent light from a single-mode laser diode to quantum dot superluminescent diode broadband radiation. Tuning the power ratio, we realize tailored second-order correlations ranging from Gaussian to Poissonian statistics. Both experiments are very well matched by theory, thus giving first insights into the quantum properties of radiation from quantum dot superluminescent diodes. [ABSTRACT FROM AUTHOR]

An experimental laser teaching system is developed to demonstrate laser feedback phenomena, which bring great harm to optical communication and benefits to precision measurement. The system consists of an orthogonally polarized He-Ne laser, a feedback mirror which reflects the laser output light into the laser cavity, and an optical attenuator which changes the intensity of the feedback light. As the feedback mirror is driven by a piezoelectric ceramic, the attenuator is adjusted and the feedback mirror is tilted, the system can demonstrate many basic laser feedback phenomena, including weak, moderate and strong optical feedback, multiple feedback and polarization flipping. Demonstrations of these phenomena can give students a better understanding about the intensity and polarization of lasers. The system is well designed and assembled, simple to operate, and provides a valuable teaching aid at an undergraduate level. [ABSTRACT FROM AUTHOR]

A passive coherent beam combination of three nanosecond Yb-doped fiber amplifiers by an all-optical feedback loop is realized by a Dammann grating intracavity spatial filter. By using this diffractive-optics-based spatial filtering technique, three tile-aperture laser beams are phase-locked with a peak power of 1.02 kW. The width of the combined pulses is 9.6 ns, and the repetition frequency is 2.208 MHz. The visibility of the far-field interference pattern is up to 82.9%. The results show that this approach can scale to larger arrays and higher powers. [ABSTRACT FROM AUTHOR]

We demonstrate a self-injection locking extended cavity diode laser (ECDL) using resonant optical feedback from the p-polarization of a monolithic folded Fabry--Perot parallel cavity (MFC). The full width at half maximum of the MFC resonance is 31 MHz. With the help of a narrow-linewidth reference laser, the linewidth of the ECDL is measured to be about 7 kHz. The frequency of the laser could be tuned at 160 MHz with an amplitude of 40 V by a PZT mounted on the monolithic cavity and the voltage tuning coefficient is about 4 MHz/V. [ABSTRACT FROM AUTHOR]