Search

An electron cyclotron heating (ECH) system has been installed on the TRIAM-1M tokamak, which produces a 170 GHz microwave up to 260 kW at the window of the gyrotron for 5 sec. After the Matching Optical Unit (MOU) converts the microwave to a Gaussian beam, a microwave power of 200 kW is transmitted by a corrugated waveguide of 63.5 mm in diameter. Tests confirmed these specifications, and the fundamental ordinary electron cyclotron (EC) wave of 170 GHz up to 120 kW was injected into the vacuum vessel of the TRIAM-1M in order to ionize neutral hydrogen gas to make source plasma, which is expected to reduce flux consumption in the case of current start-up by means of Ohmic heating (OH) coils. Though the breakdown does not occur at the input RF power, PRF = 40 kW with the neutral gas pressure, p = 1.3×10−3Pa, high-density plasma (more than 0.7×1019m−3) is produced at PRF = 100 kW. In the range of PRF = 40−100 kW, the electron density is proportional to PRF.

The study of wall recycling of long duration discharge has been carried out using 2.45 GHz and 8.2 GHz lower hybrid current drive in the superconducting tokamak TRIAM-1M. The recycling coefficient increases with two time constants. One is 1˜3 s and the other is ˜30 s. These two time constants are common to low (˜2 × 1018 m-3) and high (˜1 × 1019 m-3) density discharges. In the ultra-long discharge, the wall repeats a process of being saturated and refreshed. One possible candidate of the mechanism of wall refreshment is co-deposition of in vessel element (i.e. Molybdenum). In the high density discharge, the wall becomes saturated and the discharge is terminated due to the density increase. The achievable discharge duration becomes shorter as the plasma density is higher.

Ohmic plasma currents of up to 17 kA with a discharge duration of 0.32 s have been obtained in the Kyushu University Experiment with Steady-State Spherical Tokamak (QUEST) with the help of electron cyclotron wave (ECW) and cancellation coils (CCs). The CCs, originally installed to create a field null in the plasma breakdown phase, are essential for producing plasma current in QUEST. Although the ohmic coil current is initially biased and then reduced completely to zero to induce the plasma current in 15-20 ms, we demonstrate that the flat top of the plasma current exceeding 20 ms is maintained by the vertical field after the ohmic current is switched off. This type of operation is quite favorable for extending pulsed operation to the steady state by electron Bernstein wave current drive (EBCD).

Because QUEST tokamak has a divertor configuration with a higher κ and a negative n-index, a precise power supply with a rapid response is needed to control the vertical position of the plasma. A matrix converter is a direct power conversion device that uses an array of controlled bidirectional switches as the main power elements for creating a variable-output current system. This paper presents a novel three-phase to two-phase topological matrix converter as a proposed power supply that stabilizes the plasma vertical position and achieves unity input power factor. An indirect control strategy in which the matrix converter is split into a virtual rectifier stage and a virtual inverter stage is adopted. In the virtual rectifier stage, the instantaneous active power and reactive power are decoupled on the basis of system equations derived from the DQ transformation; hence, unity power factor is achieved. Space vector pulse width modulation is adopted to determine the switching time of each switch in the virtual rectifier; the output voltage of the virtual rectifier is adjusted by the virtual inverter stage to obtain the desired load current. Theoretical analyses and simulation results are provided to verify its feasibility.

This paper presents a scheme for combining a Langmuir probe with a fast camera for measurement of the behavior of blob-like structures in the boundary region of an electron cyclotron resonance (ECR) heating plasma in Q-shu University Experiment with a Steady-State Spherical Tokamak (QUEST, major radius, R = 0.68 m, minor radius, a = 0.40 m, and toroidal magnetic field, Bt = 0.25 T at R = 0.64 m). The frame rate of the camera was typically set to 40,000 frames per second (FPS) with 192 × 144 pixels per frame. Radial motion of blob-like structures was observed in the half of the plasma space where the probe head was located. A radially movable and rotatable probe system was used to measure the floating potential from single unbiased tips, the potential of the positively biased tip, and the ion saturation current in two orthogonal directions in the outboard midplane region. Time series of the ion saturation current measured by the Langmuir probe and of pixels in a 40,000 FPS movie were compared and cross-correlated. The results of the two diagnostics agreed well, and the spatial scale was found to be of the same as the size of the probe head. The ion saturation current was asymmetric in terms of the time the blob-like structure was passing; fast camera imaging also clearly demonstrated the blobs' filamentary structures and radial motion at the edge of QUEST. This means that plasma in the blob-like structure hunches over, like blobs in other devices. The typical radial velocity of the structures is ∼1 km/s, and the structures were accelerated along their path of radial motion from the inner to the outer parts of the vacuum vessel.

It is important to determine the best method for reconstructing the magnetic flux when eddy currents are significantly induced during magnetic measurement in spherical tokamaks (STs). Four methods for this reconstruction are investigated, and the calculated magnetic fluxes are compared to those measured in the cavity of a vacuum vessel. The results show that the best method is the one that uses currents from virtual coils for reconstruction. In this method, the placement of the virtual coils is optimized with numerical simulations using the Akaike information criterion (AIC), which indicates the goodness of fit of models used to fit measured data. The virtual coils are set on a line 15 cm outside the vacuum vessel.

Various phenomena of plasma-wall interactions during long duration discharges in TRIAM-1M are investigated from macroscopic and microscopic viewpoints. It is found that the density dependence of the hydrogen neutral flux decay length is not very sensitive to the density (i.e. ne−0.2 ). Neutral transport through the scrape-off layer is important for structural formation of hydrogen recycling. The hydrogen retention in the co-deposited layer, which was obtained using a material probe during long duration discharges, is consistent with the global wall pumping rate estimated from particle balance analysis. The wall temperature and co-deposition play important roles on hydrogen re-emission and hydrogen absorption, respectively. Oxygen impurities should affect the erosion and deposition properties of the plasma-facing wall as well as the hydrogen retention property of the co-deposited layer. The co-deposition of hydrogen with molybdenum and the oxygen impurities both play important roles in the hydrogen recycling.

QUEST focuses on the steady state operation of the spherical tokamak by controlled PWI and electron Bernstein wave current drive. One of the main purposes of QUEST is an achievement of long duration discharge with MW-class injected power. As the result, QUEST should be operated in the challenging region on heat and particle handling. To do the particle handling, high temperature all metal wall up to 623 K and closed divertors are planned, which is to realize the steady-state operation under recycling ratio, R = 1. This is a dispensable check to DEMO, because wall pumping should be avoided as possible in the view of tritium retention. The QUEST project will be developed in increment step such as, I. low β steady state operation in limiter configuration, II. low β steady state operation in divertor configuration, III. relatively high β steady state operation in closed divertor configuration. Phase I in the project corresponds to these two years, and final goal of phase I is to make full current drive plasma up to 20 kA. Closed divertor will be designed and tested in the Phase II. QUEST is running from Oct., 2008 and the first results are introduced.

A new technique to measure the current profile in plasmas with asymmetric distribution function such as lower hybrid current drive (LHCD) by using hard X-ray (HXR) energy spectrum measurement along the top and bottom identical line of sights (ILOS) is proposed and is applied to the full and partially LHCD plasmas on the TRIAM-1M tokamak at the first time in the world. The pitch angles were measured at R - R0 = ±2.5 cm, where R, R0 mean the major radii of the ILOS and the magnetic axis, respectively. The measured pitch angle of the magnetic field inverted at the magnetic axis estimated magnetic measurement in partially LHCD plasmas. This indicates that the difference of the measured pitch angles is caused by the plasma current in the plasma and this new method is available in detecting the current profile in tokamaks. In full LHCD plasma, no difference between the HXR signals along the top and bottom ILOS appear. This indicates that the current density around the magnetic axis was reduced compared with that in partially LHCD plasmas. This observation is no contradiction with power deposition of LHCD.

A simple model of radio frequency wave (RF) assisted breakdown based on Townsend avalanche theory is proposed for the purpose of evaluating the effect of RF on Townsend avalanche breakdown. According to this model, the required minimum electric field for RF-assisted breakdown can be decreased down to half of that for breakdown by the induction electric field alone. The electric field of RF reaches a minimum when the frequency of the RF is equal to the electron cyclotron frequency.