Search

Compared to the conventional boost power factor correction (PFC) converter, a totem-pole bridgeless PFC has high efficiency because it does not have an input diode rectifier stage, but a current spike may occur when the polarity of the grid voltage changes. This paper proposes a digital control algorithm for bridgeless totem-pole PFC with a simple control structure based on the phase angle of grid voltage. The proposed algorithm has a PI-based double-loop control structure and performs DC-link voltage and input inductor current control. Rectifying switches operate based on the proposed rectification algorithm using phase angle information calculated through a single-phase phase-locked loop (PLL) to prevent current spikes. The feed-forward duty ratio value is calculated according to the polarity of the grid voltage and added to the double-loop controller to perform appropriate power factor control. The performance and feasibility of the proposed control algorithm are verified through a 3 kW hardware prototype. [ABSTRACT FROM AUTHOR]

This paper proposes a single-phase, transformer-less, seven-level inverter that utilizes eight switches, three capacitors, and two diodes to produce seven voltage levels with triple boosting ability. The availability of the common-ground point eliminates the leakage current in PV applications. The proposed Transformer-Less Triple-Boosting Seven-Level Inverter (TLTB7LI) has the ability to feed different types of loads from non-unity to unity power factors. The voltage balancing of capacitors takes place naturally without the need for auxiliary circuits and complicated control strategies. This paper investigates the appropriateness of the proposed TLTB7LI for grid-connected application. The Peak Current Controller (PCC) is employed to generate the switching pulses and regulate the active/reactive power transfer between the converter and the output, which guarantees the high quality of injected current to the output. Moreover, the operational principles, its control technique, as well as the design procedure of the key components of the proposed inverter have been presented. The superiority of the proposed inverter over existing counterparts has been verified through comparative analysis. The simulation and experimental analysis validated the proper operation of the proposed TLTB7LI. [ABSTRACT FROM AUTHOR]

This paper proposes a Symmetric High Voltage-Gain (SHVG) boost converter control for photovoltaic system applications. The concept is based on a multilevel boost converter configuration, which presents an advantage compared to a classic boost converter such as the ability to transfer a high amount of power with less stress on the power electronics components in the high voltage-gain conditions. This advantage allows the power losses in the converter to be reduced. A mathematical-based voltage model of the PV system using variable series resistance depending on solar irradiance and the temperature is proposed. This model is connected to an SHVG boost converter to supply the load's power. A control strategy of the DC-bus voltage with maximum power point tracking (MPPT) from the PV system using PI controllers is developed. The contributions of the paper are focused on the SHVG operating analysis with the passive components' sizing, and the DC-bus voltage control with maximum power point tracking of the PV systems in dynamic operating conditions. The performances of the proposed control are evaluated through simulations, where the results are interesting for high-power photovoltaic applications. [ABSTRACT FROM AUTHOR]

This paper introduces a new hybrid DC–DC converter with enhanced voltage gain and synchronized multiple output capabilities, specifically tailored for smart grid applications. The proposed converter is based on the integration of non-isolated Zeta and Mahafzah converters, comprising a single controlled switch, two diodes, three inductors, and two coupling capacitors. The primary objective of this novel hybrid converter is to improve voltage gain as compared to conventional Zeta and Mahafzah topologies. By achieving higher voltage gain at lower duty cycles, the converter effectively reduces voltage stress on semiconductor switches and output diodes, thereby enhancing overall performance and reliability. A comprehensive examination of the hybrid converter's operating principle is presented, along with detailed calculations of duty cycle and switching losses. The paper also explores the converter's application in smart grids, specifically in the context of renewable energy systems and electric vehicles. Two distinct scenarios are analyzed to evaluate the converter's efficacy. Firstly, the converter is assessed as a DC–DC converter for renewable energy systems, highlighting its relevance in sustainable energy applications. Secondly, the converter is evaluated as an electric vehicle adapter, showcasing its potential in the transportation sector. To validate the converter's performance, extensive simulations are carried out using MATLAB/SIMULINK with parameters set at 25 kW, 200 V, and 130 A. The simulation results demonstrate the converter's ability to efficiently supply multiple loads with opposing energy flows, making it a promising technology for optimized grid management and energy distribution. Moreover, the paper investigates the total harmonic distortion (THD) of the grid current, focusing on its impact in smart grid environments. Notably, the new hybrid converter topology achieves a THD of 21.11% for the grid current, indicating its ability to effectively mitigate harmonics and improve power quality. Overall, this research introduces a cutting-edge hybrid DC–DC converter that enhances voltage gain and synchronizes multiple outputs, specifically catering to the requirements of smart grid applications. The findings underscore the converter's potential to significantly contribute to the advancement of efficient and resilient power conversion technologies for smart grids, enabling seamless integration of renewable energy systems and electric vehicles into the grid. [ABSTRACT FROM AUTHOR]

This paper studies the stability of a real-world wind farm, Bison Wind Generation System (BWGS) in the state of North Dakota in the United States. BWGS uses an AC collector grid rated at 34.5 kV and a symmetrical bipolar high-voltage DC (HVDC) transmission grid rated at ±250 kV. The HVDC line transfers a total power of 0.5 GW, while both the HVDC rectifier and inverter substations use line-commuted converters (LCCs). The LCC-based rectifier adopts constant DC current control to regulate HVDC current, while the inverter operates in constant extinction angle control mode to maintain a fixed HVDC voltage. This paper proposes a frequency scan-based approach to obtain the d–q impedance model of (i) BWGS AC collector grids with Type 4 wind turbines that use permanent magnet synchronous generators (PMSGs) and two fully rated converters, and (ii) an LCC-HVDC system. The impedance frequency response of the BWGS is acquired by exciting the AC collector grid and LCC-HVDC with multi-sine voltage perturbations during its steady-state operation. The resulting voltage and current signals are subjected to a fast Fourier transform (FFT) to extract frequency components. By analyzing the impedance frequency response measurement of BWGS, a linear time–invariant (LTI) representation of its dynamics is obtained using the vector fitting (VF) technique. Finally, a Bode plot is applied, considering the impedance of the BWGS and grid to perform stability analyses. This study examines the influence of the short circuit ratio (SCR) of the grid and the phase lock loop (PLL) frequency bandwidth on the stability of the overall system. The findings provide valuable insights for the design and verification of an AC collector and LCC-based HVDC transmission systems. The findings suggest that the extraction of the impedance model of a real-world wind farm, achieved through frequency scanning and subsequent representation as an LTI system using VF, is regarded as a robust, suitable, and accurate methodology for investigating the dynamics, unstable operating conditions, and control interaction of the wind farm and LCC-HVDC system with the AC grid. [ABSTRACT FROM AUTHOR]

This paper proposes an improved zero-current distortion compensation (IZCDC) method for the Vienna rectifier. The conventional zero-current distortion compensation (ZCDC) method modifies the reference voltages by adding an offset voltage to compensate for the zero-current distortion (ZCD). However, the reference voltages occasionally exceed the linear modulation region by the offset voltage added at the driving start-point of the Vienna rectifier, where the modulation index of phase voltage is relatively large. This causes a hard-start of the Vienna rectifier accompanied by a serious surge and distortion in the phase current. In this paper, the IZCDC method is proposed for achieving the soft-start of the Vienna rectifier. When the overmodulation occurs, the proposed method modifies the conventional offset voltage to the IZCDC component, which is involved in the adjustment of the variance of the phase current, only for a certain phase among the three phases. As the IZCDC component regulates the variance of the phase current to zero, surge and distortion in the phase current can be mitigated. As a result, the Vienna rectifier starts its operation softly while ensuring its normal operation in the transients. The effectiveness of the proposed method is verified through simulations and experimental results. [ABSTRACT FROM AUTHOR]

The reliability of power electronic switching components is of great concern for many researchers. For their usage in many mission profiles, it is crucial for them to perform for the duration of their intended lifetime; however, they can fail because of thermal stress. Thus, it is essential to analyze their thermal performance. Non-linear switching action, bifurcation and chaotic events may occur in DC-DC power converters. Consequently, they show different behaviors when their parameters change. However, this is an opportunity to study these bifurcation phenomena and the existence of chaos, e.g., in boost converters, on their performance as the effects of load variations (mission profiles) on the system's behavior. These variations generate many non-linear phenomena such as periodic behavior, repeated period-doubling bifurcations and chaos in the MOSFET drain-source current. Thus, we propose, for the first time, an analysis of the influence of chaos on the junction temperature. First of all, this paper provides a step-by-step procedure to establish an electrothermal model of a C2M0080120D MOSFET with integrated power loss. Then, the junction temperature is estimated by computing the power losses and a thermal impedance model of the switch. Additionally, this model is used to investigate the bifurcation and chaotic behavior of the MOSFET junction temperature. The paper contributes by providing a mathematical model to calculate several coefficients based on experimental data and thermal oscillations. Estimation of the number of cycles to failure is given by the Coffin–Manson equation, while temperature cycles are counted using the rainflow counting algorithm. Further, the accumulated damage results are calculated using the Miner's model. Finally, a comparison is made between the damage accumulated during different mission profiles: significant degradation of the MOSFET's lifetime is pointed out for chaotic currents compared to periodic ones. [ABSTRACT FROM AUTHOR]

To reduce the current harmonics on the input side of a multi-pulse rectifier, this paper proposes a low harmonic current source series multi-pulse rectifier based on an auxiliary passive injection circuit at the DC side. The rectifier only needs to add an auxiliary passive injection circuit on the DC side of the series 12-pulse rectifier, which can change its AC input voltage from 12-step waves to 24-step waves. We analyzed the working mode of the rectifier, optimized the optimal turn ratio of the injection transformer from the perspective of minimizing the total harmonic distortion (THD) value of the input voltage on the AC side, and analyzed the diode open circuit fault in the auxiliary passive injection circuit. Test verification shows that, after using the passive harmonic injection circuit, the THD value of the input voltage of the AC side of the rectifier is reduced from 14.03% to 4.86%. The THD value of the input current is reduced from 5.30% to 2.16%. The input power factor has been increased from 98.86% to 99.83%, and the power quality has been improved. [ABSTRACT FROM AUTHOR]

Three-phase voltage PWM rectifier is a multivariable, strong coupling, nonlinear multi-input and multi-output system. In the design of rectifier control systems, with PI control it is difficult to achieve the ideal control effect, the dynamic performance is poor, and the parameter computation is complex. Moreover, the traditional sliding mode control voltage outer loop suffers from the problem of chattering, which is difficult to solve. Responding to the above issues, a new type of variable speed reaching law is proposed, which is applied to the voltage outer loop sliding mode control, while the feedback linearization principle is introduced to the current inner loop, and a new type of double closed-loop sliding mode control system is obtained by applying the two theories to the design of the sliding mode controller. A simulation model is established in MATLAB/Simulink to compare the PI control, the SMC control and the V-SMC control strategy proposed in this paper (voltage outer loop V-SMC current inner loop FLC-SMC control), and the simulation results show that the rectifier under the new dual-closed-loop sliding mode control strategy has the advantages of good dynamic performance, strong robustness and strong anti-interference ability. At the same time, compared with the traditional sliding mode control strategy, the vibration suppression effect under the proposed control strategy is obvious. Finally, a 10 kW rectifier control system is built on a semi-physical hardware-in-the-loop experimental platform to further verify the correctness and superiority of the proposed control strategy. [ABSTRACT FROM AUTHOR]

This paper presents a computer-simulation-based design of an in-line, coaxial-to-circular waveguide adapter for converting the coaxial transverse electromagnetic (TEM) mode to the circular waveguide TE11 mode over more than a one-octave bandwidth. The proposed adapter consists of a coaxial-to-rectangular waveguide transformer employing a stepped-ridge converter and a rectangular-to-circular waveguide transformer employing a curved transition. The proposed adapter has been optimized using a commercial simulation tool. The dimensions of the designed adapter are given so that it can be verified by anyone who is interested. The designed adapter operates from 8.00 GHz to 22.95 GHz (2.87:1 bandwidth) with a reflection coefficient of less than −20 dB and a higher-order mode level of less than −25.0 dB. [ABSTRACT FROM AUTHOR]

Zero-voltage zero-current switching (ZVZCS) phase-shifted full-bridge (PSFB) converters have been widely used in high-power applications because of their high efficiency, low price, and easy control. Currently, the biggest problem with PSFB converters in operation is their high duty cycle loss. With the increase in current, duty cycle loss grows and degrades their performance. Focusing on this problem, a new ZVZCS PSFB converter is proposed in this paper. This topology adds an auxiliary circuit to minimize duty cycle loss. Moreover, the lagging-leg switches can obtain zero-current switching (ZCS) easily with the help of the circuit. The auxiliary circuit is built of four metal-oxide-semiconductor field-effect transistors (MOSFETs) and an auxiliary transformer, and extra voltage can be added to the primary coils when the direct-current (DC) voltage is small. This paper discusses its operation principles and characteristics, and an experiment of a 2 kW prototype was conducted, the results of which demonstrate the advantages of the presented circuits. [ABSTRACT FROM AUTHOR]

Power converters can convert the electrical energy output by power source into specific forms required by target device. They are widely used in various fields such as electrification, transportation, and power systems, and are the core components of the systems. Power converters are composed of power semiconductor devices (such as IGBTs), which are prone to failure due to abnormal conditions and aging degradation, leading to power converter faults. Therefore, over the past twenty years, extensive fault diagnosis methods for power converters have been studied and proposed. Among them, symmetry-based methods have the characteristics of rapid diagnosis speed and strong robustness, but so far there's no systemic summary of such methods. Therefore, this paper reviews the relevant research on fault diagnosis of power converters based on symmetry in recent years, analyzes the mathematical principles of these methods, and compares their diagnostic performance. In addition, two factors that may have an influence on the symmetry are pointed out. This paper provides references and suggestions for the future development and research of power converter fault diagnosis. [ABSTRACT FROM AUTHOR]

This paper proposes a simple design scheme for a modular NPC inverter using thermal RC network analysis. The proposed design process is an efficient and straightforward approach to designing the heatsink for a 300 kW modular neutral-point-clamped inverter. The heatsink design plays a crucial role in achieving high power density of a power converter because the weight and size of the heatsink are primarily influenced by its type. The structure and dimensions of the heatsink are mainly determined based on the generated heat by losses of the power semiconductor switches. In this paper, a thermal RC network model was established using parameters from the power switch module and was applied to the simulation of the power converter. The thermal losses of the power semiconductor switches were calculated via this process, and the heatsink was designed according to the calculated thermal losses. The proposed design scheme was analyzed and compared with the thermal fluid dynamic model. To validate the feasibility of the proposed design process, The simulation results were compared with experimental results. [ABSTRACT FROM AUTHOR]

The main aim of this study is the development of a fast and secure charging system for electric vehicles. Recently, many different charging methods have been introduced. The main charging methods are the induction charging method and the conduction charging method. In this paper, the conduction charging method is employed. With regard to the conduction method, there are three levels of charging. At level 1, there is single-phase charging, while both single-phase and three-phase charging occur at level 2. Lastly, at level 3, a three-phase AC charging method, DC conduction charging method, and AC/DC conduction charging method is focused. The level 3 charging method is the main focus of this paper. Toward this end, a 12-diode rectifier or 12-pulse rectifier with a firing angle of zero degrees having two bridges is used for AC to DC conversion, while a SEPIC converter is used for DC-to-DC conversion. The design presented in this paper was simulated and verified using MATLAB/Simulink, and the results show that the Total Harmonic Distortion (THD) of the input current was reduced, and that overall efficiency was improved. [ABSTRACT FROM AUTHOR]

The recently proposed novel unidirectional multilevel rectifier, a three single-phase star-connected multilevel rectifier, has the characteristic of having a large number of DC-side capacitors and a complex capacitor voltage balancing control structure under conventional carrier-based phase-shift sine wave pulse-width modulation (SPWM). Hence, a space vector pulse-width modulation (SVPWM) algorithm for the novel multilevel rectifier is proposed in this paper, which can quickly balance the capacitor voltage without an additional voltage balancing control structure. Firstly, it divides the space vectors of the rectifier, then it determines the two basis voltage vectors that synthesize the output reference voltage. After that, based on the analysis of the relationship between switching states and the charge–discharge of capacitors, the final action sequences of redundant vectors are determined according to the principle of keeping the capacitor charge–discharge time consistent. Thus, the capacitor voltages can be automatically balanced without an additional voltage balancing control structure. Finally, simulation and experimental results validated the feasibility and effectiveness of the proposed SVPWM algorithm. The results also show improvements in current quality, capacitor voltage balance and the fluctuation of the neutral point voltage on the DC-link, allowing for further reduction in the overall volume and cost of the rectifier. [ABSTRACT FROM AUTHOR]

The design and optimization of power converters is a key factor in the growth and development of the power electronics field. However, the process of designing a power converter is not straightforward, and engineers often rely on experience and intuition, sometimes requiring time-consuming computer simulations. This paper presents a tool for the basic design of grid-connected AC–DC converters. The design tool takes specifications and operating conditions for two-level and three-level NPC converter topologies and derives a draft design. The tool calculates the input filter's electrical parameters, the converter's losses, the temperature rise of the power semiconductor devices, and the ripple current and voltage of the DC-link capacitor. In order to validate the proposed design tool, four AC–DC converters using SiC MOSFETs were designed. Based on the design results, simulation models and prototypes were fabricated to verify the performance and confirm that the proposed design tool can be used in the basic design process of converters. [ABSTRACT FROM AUTHOR]

This paper presents a compact stacked RF energy harvester operating in the WiFi band with multi-condition adaptive energy management circuits (MCA-EMCs). The harvester is divided into antennas, impedance matching networks, rectifiers, and MCA-EMCs. The antenna is based on a polytetrafluoroethylene (PTFE) substrate using the microstrip antenna structure and a ring slot in the ground plane to reduce the antenna area by 13.7%. The rectifier, impedance matching network, and MCA-EMC are made on a single FR4 substrate. The rectifier has a maximum conversion efficiency of 33.8% at 5 dBm input. The MCA-EMC has two operating modes to adapt to multiple operating conditions, in which Mode 1 outputs 1.5 V and has a higher energy conversion efficiency of up to 93.56%, and Mode 2 supports a minimum starting input voltage of 0.33 V and multiple output voltages of 2.85–2.45 V and 1.5 V. The proposed RF energy harvester is integrated by multiple-layer stacking with a total size of 53 mm × 43.5 mm × 5.9 mm. The test results show that the proposed RF energy harvester can drive a wall clock (30 cm in diameter) at 10 cm distance and a hygrometer at 122 cm distance with a home router as the transmitting source. [ABSTRACT FROM AUTHOR]

Time-to-digital converters (TDCs) with superior performance are in high demand in application domains like light detection and ranging (LIDAR), nuclear physics, and time interval counters. One of the interesting architectures for field-programmable gate array (FPGA)-based TDCs is the tapped delay line (TDL) approach with carry chains as delay elements. However, the resolution of TDL-TDCs is limited, and linearity is weakened by the ultra-wide bins that correspond to the FPGA's long routing wires crossing into another clock area. This paper presents wave union TDC using FPGA internal routing wires as delay elements to subdivide ultra-wide bins. The Zynq Evaluation and Development (ZED) board is used to implement and test the wave union types: A (WU-A) and B (WU-B) TDCs. According to experimental data, the WU-A TDC based on an 8 × 128 matrix of counters has a resolution of 5.7 ps, an integral nonlinearity (INL) of 1.1170 LSB (RMS), and a differential nonlinearity of 0.329 LSB (RMS). WU-A TDC improves DNL and INL by 19% and 57%, respectively, over ordinary TDC. The WU-B TDC uses an average of sixteen different time measurements, resulting in an effective resolution of up to 0.356 ps, a DNL of 0.60 LSB (RMS), and an INL of 1.04 LSB (RMS). These characteristics make the TDC suitable for time-of-flight applications such as LIDAR and for other general-purpose scientific instruments. [ABSTRACT FROM AUTHOR]

Rectifier plays a pivotal role in wireless power transfer systems. While numerous studies have concentrated on enhancing efficiency and bandwidth at specific high-power levels, practical scenarios often involve unpredictable power inputs. Consequently, a distinct need arises for a rectifier that demonstrates superior efficiency across a broad range of input power levels. This paper introduces a high-power RF-to-DC rectifier designed for WPT applications, featuring an ultrawide dynamic range of input power. The rectification process leverages a GaN (gallium nitride) high electron mobility transistor (HEMT) to efficiently handle high power levels up to 12.6 W. The matching circuit was designed to ensure that the rectifier will operate in class-F mode. A Schottky diode is incorporated into the design for relatively lower-power rectification. Seamless switching between the rectification modes of the two circuits is accomplished through the integration of a circulator. The proposed rectifier exhibits a 27.5 dB dynamic range, achieving an efficiency exceeding 55% at 2.4 GHz. Substantial improvement in power handling and dynamic range over traditional rectifiers is demonstrated. [ABSTRACT FROM AUTHOR]

The increasing penetration of renewable energy sources (RESs) in transmission and distribution systems presents several challenges for grid operators. In particular, the unpredictable behavior of RESs can disrupt the balance between energy production and load demand, potentially affecting the stability of the entire system. Grid-connected energy storage systems (ESSs) offer a possible solution to manage the uncertainty associated with RESs. In fact, ESSs exchange power with the grid through the adoption of suitable energy management strategies, which are typically implemented by power electronics-based grid interfaces. Unlike other current source converter (CSC) solutions described in the literature, which only interface with a single energy storage device, this paper introduces a novel topology for a three-phase delta-type current source converter (D-CSC), which is capable of integrating three independent ESSs using the same number of semiconductors as traditional CSC solutions. Thus, it considerably enhances the flexibility of a power conversion system (PCS) without increasing the number of converter components. In addition, an innovative energy management control strategy is also introduced. This strategy enables the D-CSC to compensate for energy imbalances arising between the three ESSs, which might be caused by several factors, such as different aging characteristics, converter component tolerances, operating conditions, and temperature drifts. Hence, the D-CSC-based interface is capable of proper grid operation even if the three ESSs have different characteristics, thus opening the possibility of employing this converter to integrate both first and second-life devices. First, the topology of the proposed D-CSC is introduced, followed by a detailed mathematical description of its control strategy. The proper grid operation of the D-CSC was tested under different scenarios, considering the grid integration of three independent superconducting magnetic energy storage systems in a marine vessel. The proposed D-CSC is compared to traditional CSC solutions, highlighting the superior performances of the novel converter topology in terms of efficiency, total harmonic distortion of the output currents, and overall cost reduction for the PCS. [ABSTRACT FROM AUTHOR]

The inherent second harmonic power pulse in single-phase grid-connected rectifiers leads to a noticeable output voltage ripple and thus results in the degradation of the system. A novel second harmonic suppression control is introduced in this paper to address this issue. The key point of the proposed control lies in the real-time prediction of the phase-shifted full-bridge (PSFB) converter's desired duty cycle through accurate PSFB converter modeling. By accurately predicting the ideal duty cycle, the proposed control facilitates a significant enhancement in the control loop's gain specifically at the second harmonic frequency, thereby improving the overall system performance. To validate the theoretical analysis, a series of simulations and experiments were conducted. The results demonstrate the effectiveness of the proposed second harmonic suppression control in mitigating second harmonic output voltage ripple. [ABSTRACT FROM AUTHOR]

To effectively eliminate the impacts of both matched and mismatched power disturbances in a three-phase PWM rectifier, this paper proposes a robust direct power control (RDPC) method with a single-loop control structure. Firstly, a nonlinear power model of the three-phase PWM rectifier is established. Then, using the exact feedback linearization method, a linearized power model including matched and mismatched power disturbances is derived and achieves the decoupling of active and reactive power. Secondly, to regulate the DC bus voltage, a sliding-mode controller (SMC) combined with a nonlinear disturbance observer (NDO) is proposed. The proposed SMC combined with an NDO (SMC + NDO) method features a single-loop control structure, which enables a faster response and simpler structure compared to the dual-loop DPC method. By incorporating estimated mismatched power disturbance into the sliding-mode surface, it overcomes the SMC's defect in incompletely suppressing mismatched disturbances and enables the simultaneous regulation of voltage and active power. Additionally, it effectively reduces sliding-mode chattering. To regulate reactive power, a sliding-mode controller based on the exponential convergence law is designed to suppress matched reactive power disturbances. Finally, the simulation and experimental comparative results demonstrate that the proposed controller exhibits stronger robustness against matched and mismatched power disturbances, as well as a better performance under the constant power load (CPL). [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive review on the employment of wide bandgap (WBG) semiconductor power devices in wind energy conversion systems (WECSs). Silicon-carbide- (SiC) and gallium-nitride (GaN)-based power devices are highlighted and studied in this review, focusing on their application in the wind energy system. This is due to their premium characteristics such as the operation at high switching frequency, which can reduce the switching losses, and the capability to operate at high temperatures compared with silicon (Si)-based devices. These advantages promote the replacement of the conventional Si-based devices with the WBG semiconductor devices in the new modular converter topologies due to the persistent demand for a more-efficient power converter topology with lower losses and smaller sizes. The main objective of this paper was to provide a comprehensive overview of the WBG power devices commercially available on the market and employed in the modular converter topologies for renewable energy systems. The paper also provides a comparison between the WBG power technologies and the traditional ones based on the Si devices. The paper starts from the conventional modular power converter topology circuits, and then, it discusses the opportunities for integrating the SiC and WBG devices in the modular power converters to improve and enhance the system's performance. [ABSTRACT FROM AUTHOR]

When the wind turbine operates under frequently fluctuating mission profiles, the power semiconductors of its converter will generate low-frequency junction temperature fluctuations, resulting in accumulation of damage to the devices and affecting the converter's lifetime. To address the above issues, an active thermal control (ATC) strategy based on reactive circulating current for the parallel converter of permanent magnet synchronous generator wind power system was proposed in this paper, by introducing reactive circulating current during sudden wind speed drops, the thermal cycle of the power semiconductor can be effectively smoothed. On the other hand, considering the impact of the proposed strategy on the voltage vector and modulation index of the converter, both the machine-side converter (MSC) and the grid-side converter (GSC) during the control process will be analyzed in detail, then the reactive current of GSC will be limited to prevent excessive modulation index and maintain system stability without reducing the filter size. Finally, a 2 MW wind power system is utilized as a benchmark, and both short-term simulation analysis and long-term numerical results reveal the effectiveness of the control strategy proposed in this paper. [ABSTRACT FROM AUTHOR]

The paper deals with a grid-connected single-phase battery charger integrated with photovoltaic generators (PVGs). The circuit topology consists of a multilevel architecture based on a Cascaded H-Bridge (CHB) rectifier. Its main task is to charge the batteries, primarily from the PVGs, by also assuring to keep their state-of-charge (SOC) balanced. Nevertheless, when the battery SOC overcomes a predefined upper limit, beyond which the charging process could be interrupted, the available PV power can no longer be transferred to the batteries. Therefore, to avoid an undesired curtailment of PV power production, this latter can be supplied to the grid by inverting the system operation. The paper shows how to achieve this result by implementing a dedicated control action based on a multi-step procedure. Numerical investigations are carried out on a 19-level CHB converter implemented in the PLECS environment to validate the feasibility and effectiveness of the proposed control technique. [ABSTRACT FROM AUTHOR]

A home energy management system (HEMS) was designed in this paper for a smart home that uses integrated energy resources such as power from the grid, solar power generated from photovoltaic (PV) panels, and power from an energy storage system (ESS). A fuzzy controller is proposed for the HEMS to optimally manage the integrated power of the smart home. The fuzzy controller is designed to control the power rectifier for regulating the AC power in response to the variations in the residential electric load, solar power from PV panels, power of the ESS, and the real-time electricity prices. A self-learning scheme is designed for the proposed fuzzy controller to adapt with short-term and seasonal climatic changes and residential load variations. A parsimonious parameterization scheme for both the antecedent and consequent parts of the fuzzy rule base is utilized so that the self-learning scheme of the fuzzy controller is computationally efficient. [ABSTRACT FROM AUTHOR]

Magnetostrictive alloys hold great promise for Energy Harvesting applications due to their inherent durability. However, their implementation often results in usable voltage ranges that fall significantly below common electronic standards like 1.6, 3.3, and 5 volts. Consequently, the utilization of electronic circuits becomes essential to amplify the voltage and enhance energy conversion efficiency. Over the past few decades, numerous conversion techniques have been devised for other intelligent materials, such as piezoelectrics, some of which have even made their way into commercial products. Surprisingly, there is a dearth of specialized techniques, if not a complete absence, tailored to magnetostrictive devices. Among potential solutions, a suitable AC–DC Boost converter stands out as a highly promising candidate for addressing this challenge, but this solution has never been fully characterized. Then, this paper presents thorough experimental validations of such a converter, driven by a real-time Arduino board equipped to measure source time periods and operate under various conditions. We present several cases demonstrating the circuit's substantial potential for enhancing energy harvesting from magnetostrictive materials. [ABSTRACT FROM AUTHOR]

This paper presents electronically tunable current conveyors using low-voltage, low-power, multiple-input operational transconductance amplifiers (MI-OTAs). The MI-OTA is realized using the multiple-input bulk-driven Metal Oxide Semiconductor transistor (MIBD-MOST) technique to achieve minimum power consumption. The MI-OTA also features high linearity, a wide input range, and a simple Complementary Metal Oxide Semiconductor (CMOS). Thus, high-performance electronically tunable current conveyors are obtained. With the MI-OTA-based current conveyor, both an electronically tunable differential difference current conveyor (EDDCC) and a second-generation electronically tunable current conveyor (ECCII) are available. Unlike the conventional differential difference current conveyor (DDCC) and second-generation current conveyor (CCII), the current gains of the EDDCC and ECCII can be controlled by adjusting the transconductance ratio of the current conveyors. The proposed EDDCC has been used to realize a voltage-to-current converter and current-mode universal filter to show the advantages of the current gain of the EDDCC. The proposed current conveyors and their applications are designed and simulated in the Cadence environment using 0.18 μm TSMC (Taiwan Semiconductor Manufacturing Company) CMOS technology. The proposed circuit uses ±0.5 V of power supply and consumes 90 μW of power. The simulation results are presented and confirm the functionality of the proposed circuit and the filter application. Furthermore, the experimental measurement of the EDDCC implemented in the form of a breadboard connection using a commercially available LM13700 device is presented. [ABSTRACT FROM AUTHOR]

The DC solid state transformer (DCSST) is a crucial component for connecting buses of different voltage levels in the DC distribution grid. This paper proposes a Si IGBT/SiC MOSFET hybrid isolated bidirectional DC–DC converter and an optimized modulation strategy (OMS) to reduce the losses and costs of DCSST. Based on the analysis of topology and operating principles, a duty-cycle modulation strategy is proposed and the converter is modeled by the time domain analysis (TDA) method. Through the analysis of switching characteristics, an optimization problem is established, which aims to reduce the conduction losses of switches while ensuring zero-voltage switching (ZVS) for all switches and low-current turn-off for IGBTs simultaneously. The optimization problem is solved by the augmented Lagrangian genetic algorithm (ALGA), and the OMS for the proposed converter is deduced. Finally, a 2 kW experimental prototype with the primary voltage of 405–495 V and the secondary voltage of 150 V is built to verify the effectiveness of the proposed topology and OMS. The switching costs of the proposed converter is reduced by 27.3% and the efficiency is improved by up to 4.04% compared to the existing method. [ABSTRACT FROM AUTHOR]

Due to their advantages in ensuring low harmonic distortion and high power factors, single-phase Pulse-Width Modulated (PWM) rectifiers are widely employed in several industrial applications. Generally, the conventional control loop of a single-phase PWM rectifier uses both voltage and current sensors. Hence, in case of sensor fault, the performance and the availability of the converter can be seriously compromised. Therefore, diagnosis approaches and fault-tolerant control (FTC) strategies are mandatory to monitor these systems. Accordingly, this paper introduces a novel multiple-sensor FTC scheme for a single-phase PWM rectifier. The proposed fault diagnosis approach relies on joining several Generalized Proportional Integral (GPI) and Model Reference Adaptive System (MRAS) observers with a residual generation technique to detect and isolate sensor faults in a simple and reliable manner. While conventional sensor FTC methods dedicated to PWM rectifiers can only deal with single faults, the suggested approach guarantees a very good effectiveness level of sensor fault detection, isolation (FDI) and FTC of multiple-sensor fault occurrence scenarios. Consequently, the single-phase PWM rectifier can work with only the survivable single sensor with the guarantee of very good performance as in healthy operation mode. The effectiveness of the proposed sensor FDI approach and its control reconfiguration performance are demonstrated through both extensive simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a theoretical analysis of steady-state operation, control-oriented modeling for voltage control, and the experimental results of a DC–DC bidirectional converter based on a Cuk converter using a voltage-doubler concept. Due to the voltage-doubler concept, the voltage stress across semiconductors is reduced when compared with the conventional Cuk converter; this allows for the use of semiconductors with reduced drain–source on-resistance. Moreover, due to the input and output current source characteristics, the converter presents advantages, such as draining/injecting currents on both sides with low-ripple currents. Furthermore, the theoretical analysis is verified by experimental results obtained from a proof-of-concept prototype designed with a 250 V input voltage, a 360 V output voltage, 2 kW rated power, and 100 kHz switching frequency. [ABSTRACT FROM AUTHOR]

The paper introduces a step-down converter that exhibits a static conversion ratio of cubic nature, providing an output voltage which is much closer to the input voltage, and at the same duty cycle, compared to a wide class of one-transistor buck-type topologies. Although the proposed topology contains many components, its control is still simple, as it employs only one transistor. A dc analysis is performed, the semiconductor stresses are derived in terms of input and output voltages and output power, revealing that the semiconductor voltage stresses remain acceptable and anyway lower than in other cubic buck topology. All detailed design equations are provided. The state-space approach is used to analyze the converter in the presence of conduction losses and a procedure for calculating the individual power dissipation is provided. The feasibility of the proposed cubic buck topology is first validated by computer simulation and finally confirmed by an experimental 12 V–10 W prototype. [ABSTRACT FROM AUTHOR]

A novel unidirectional hybrid PFC rectifier topology based on SEPIC and boost converters is proposed, which is applicable to various industrial applications such as electric vehicle charging stations, variable speed AC drives, and energy storage systems. Compared to other rectifiers, the proposed SEPIC-boost-based rectifier exhibits continuous current on the AC side, lower voltage stress on the active switches, a wider range of DC output voltage, no auxiliary DC-DC converters, and a high step-up static voltage gain operating with low input voltage and a low step-up static gain for the high-input-voltage operation. These traits allow the SEPIC-boost-based rectifier to utilize smaller input-side harmonic filtering inductors and adopt active switches with lower voltage ratings, resulting in reduced conduction losses. Additionally, the proposed rectifier features power factor correction and high boost/buck voltage-gain capabilities, simplifying control for electric vehicle charging and expanding its range of applications. In this paper, the operating principle of the novel topology is presented first, and then the mathematical model of the proposed rectifier is built. Based on this, the comparison between the proposed topology and conventional boost and SEPIC converters is given. Furthermore, the control strategy, including the high-power-factor control and the balancing control to the DC capacitor voltages, is discussed. Finally, to validate the accuracy of the proposed rectifier's theoretical research, a 500-W SEPIC-boost rectifier system has been constructed in the laboratory, generating a 200/120 Vdc output voltage from a 155 Vpk/50 Hz power source. [ABSTRACT FROM AUTHOR]

In DC microgrids, CLLC topology is commonly applied for battery integration. It provides galvanic separation, the ability to integrate a high-frequency transformer into the resonance circuit, and the ability to operate in a wide range of voltage. Moreover, it assures zero voltage switching conditions for all switches and zero current switching conditions for secondary side switches, which enables obtaining high efficiency. This paper presents a clear and effective approach to design a methodology for a CLLC DC/DC converter, especially a resonant tank. High-frequency transformer is fully integrated in a resonant tank. Its size is minimal and based on area product parameter A p . An equivalent scheme for first harmonic approximation analysis is presented with inclusion of parasitic elements. Based on it, the analytical formulas are provided, which enable graphical determination of working characteristics. It was proved that the model increases the accuracy of the results. The conditions of ZVS and maximal magnetizing inductance are established, including parasitic capacitances of secondary side switches and transformer parasitic capacitances. Based on the proposed design methodology, as the proof of concept, a small-power prototype with a GaN transistor was built operating at 364 kHz. Converter losses were determined through analytical expressions and compared with the experimental and simulation results. [ABSTRACT FROM AUTHOR]

The traction rectifier plays a key role in high-speed trains. Unexpected failure often occurs in the sensors of the rectifier, which may affect the control performance of the electric traction rectifier and even cause serious deterioration to high-speed trains. A sensor fault diagnosis method is presented in this paper, considering three kinds of common fault types. It can not only locate the sensor fault, but also identify fault types. Based on the influences of the sensor faults, the fault diagnosis thresholds can be calculated quantitatively. No additional hardware is required. First, the model of the rectifier is established, and the estimator is built. The current residuals with different faults can be obtained. Next, residuals are analyzed and features are acquired. Then, diagnosis functions are constructed, which are used for fault location and fault type identification. Finally, the feasibility and effectiveness of the method have been confirmed by the experimental results. [ABSTRACT FROM AUTHOR]

The design of modern power electronics converters requires accurate electrothermal device models enabling a straightforward parameter estimation and fast, yet accurate, circuit simulations. In this paper, a novel electrothermal averaged model of a diode–MOSFET switch for fast analysis of DC–DC converters is proposed. The model has the form of a SPICE-compatible subcircuit and allows computing in a very short simulation time the DC characteristics of the converter, the waveforms of the terminal voltages and currents of the semiconductor devices, as well as their junction temperatures, both in CCM and DCM.. All the input data required by the parameter estimation procedure can be taken from the datasheets of components. The correctness of the proposed approach is experimentally verified for a buck converter chosen as a case-study. A generally good agreement between measurements and simulations is obtained; as an example, the absolute error in assessing the MOSFET junction temperature does not exceed 12 °C within the whole range of switching frequency of the converter, while the commonly used PLECS model considerably underestimates it. [ABSTRACT FROM AUTHOR]

This paper treats a parallel 12-pulse rectifier as the study subject. The influence of unbalanced terminal voltage, the triggering angle, as well as the commutation angle of a thyristor-controlled rectifier circuit are considered in switching functions. Then, a frequency-domain harmonic coupled admittance matrix under the effect of positive sequence and negative sequence voltages are proposed, respectively. With the integration of the above matrices, a harmonic coupled admittance matrix model of a parallel 12-pulse rectifier under unbalanced voltage is proposed. On this basis, a simplified harmonic model of a 12-pulse rectifier is established, which only considers the effect of major elements through analyzing the elements' distribution and magnitude of the harmonic coupled admittance matrix, as well as the AC current harmonic producing mechanism. All the models proposed in this paper are verified with high accuracy through simulation in MATLAB/Simulink. The models proposed in this paper can be used to guide the selection of harmonic suppression measures and equipment. [ABSTRACT FROM AUTHOR]

In low-carbon energy systems, due to the high proportion of renewable energy access, the voltage regulation capacity of the system will decrease. Therefore, in the event of voltage violation, it is easy to cause large-scale renewable energy off-grid and power outages. In order to improve the voltage regulation ability of low-carbon energy system, this paper proposes a two-stage overvoltage suppression strategy for sending-end power grid. Firstly, the principle of overvoltage phenomenon in the sending end power grid of low-carbon energy system with high proportion of renewable energy access is studied, and an overvoltage control strategy composed of two stages of centralized control of rectifier station and flexible resource control of distributed power grid is proposed. Then, the PSO algorithm and consensus algorithm are used to solve the established control model. Finally, a simulation system is established based on actual operating power grid data to verify the proposed control strategy through simulation. The results indicate that the control strategy proposed in this paper can effectively suppress transient overvoltage of AC buses and improve the operational stability of the high proportion of renewable energy sending-end power grid under various operating conditions. In addition, during the daytime overvoltage regulation process, the potential of flexible regulation equipment can be fully utilized. Shortening the duration of voltage exceeding the limit and reducing the peak voltage exceeding the limit can help reduce the renewable energy waste rate of the power grid. [ABSTRACT FROM AUTHOR]

Wave energy converters are attracting attention as an energy source that can respond to climate change. In order to increase the energy efficiency of the wave energy converters, efficient power converters are also required. The efficient converters require operation at a low switching frequency, which increases the weight and volume of the passive components. Therefore, in this paper, the performance of various types of topologies is compared to select the optimal power converter for wave energy converters. In order to cope with the unbalanced operation and unbalanced load of renewable energy, in this paper, the topology of the four-leg type is analyzed centrally. In addition, the analysis was performed by applying the model predictive control that can quickly respond to the rapid energy change of wave energy. In addition, model predictive control was applied to the four-leg converter analyzed in this paper because it is suitable for application to atypical topologies. For performance analysis of various types of topology, the loss and efficiency of each converter were analyzed by applying a loss analysis model, and output current harmonics and leakage current characteristics, capacitor voltage fluctuation rate, etc., were additionally analyzed at various switching frequencies. In conclusion, the three-level four-leg converter showed up to 2.28% and 2.7% higher efficiency under balanced and unbalanced operating conditions. [ABSTRACT FROM AUTHOR]

The holistic objective of producing 100% renewable generated electricity motivates the development of low-power and efficient domestic wind turbines. The wind turbine's efficiency can be maximized by operating it in a variable speed configuration, thus harvesting all the wind power. However, the harvesting process requires a two-stage conversion from AC to DC and from DC–DC or DC–AC. The paper aims to analyze the performance of the first stage of AC–DC rectification in terms of output voltage ripple and voltage regulation when the loading conditions vary abruptly. In addition, this work investigates the basic uncontrolled and controlled rectification methods for low-power wind turbines. The role of the output capacitance and its effect on output voltage ripples is illustrated. Finally, the paper highlights the design of a three-phase controlled rectifier using a simple yet effective firing angle control of a silicon-controlled rectifier (SCR) device. The delay caused due to the firing angle variations is reported in the simulations and experimental results to support the conclusion drawn from this study. [ABSTRACT FROM AUTHOR]

This paper reviews different types of capacitors and auxiliary source circuit topologies and presents an introduction to control strategies used for circuit applications reducing DC-BUS capacitance. The paper argues in favor of replacing bulky electrolytic capacitors in capacitor-supported power electronic systems with auxiliary source circuits. DC-BUS capacitors are widely used in grid-tied power converters (rectifiers) and utilized for power balance, voltage ripple limitation, and short-term energy storage. The electrolyte capacitor is the Achilles heel of any rectifier and power converter due to its higher rate of failure than other circuitry components. Auxiliary source circuits are key components to qualitatively improve the reliability of the DC links, where they divert the instantaneous pulsating power into extra reliable storage components. Unlike previous work, this review serves to provide a clear picture of an auxiliary source circuit design, in favor of optimal solution selection according to the specific application. Therefore, energy storage components (capacitors), topologies, and control strategies of auxiliary source circuits are comprehensively reviewed in this paper. Additionally, detailed explanations, comparisons, and discussions of auxiliary source circuits are offered. [ABSTRACT FROM AUTHOR]

The semi-bridgeless power factor correction (PFC) rectifier is widely used due to its high power factor, high efficiency, and low electromagnetic interference. However, in this rectifier, the inductor current will flow through the body diode of the metal–oxide–semiconductor field-effect transistor (MOSFET) when the MOSFET does not work, causing a problem in detecting the inductor current. Consequently, the current transformers are generally used as current sensors. This means that using many current sensors will make the cost and the peripheral detection circuit complicated. In this paper, our new method is to use a gallium nitride field-effect transistor (GaNFET) to replace the metal–oxide–semiconductor field-effect transistor (MOSFET) in the main switch selection. The reverse-biased conduction voltage of the third quadrant of the GaNFET is higher than the forward-biased conduction voltage of the diode, which solves the problem in detecting the inductor current, reduces the number of current sensors, and simplifies the corresponding peripheral circuits and components. Eventually, via mathematical deduction and hardware implementation, a semi-bridgeless PFC prototype with a GaNFET was built to verify the effectiveness of the proposed structure. [ABSTRACT FROM AUTHOR]

High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of the semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. In this paper, the topology of the LCC resonant converter is adopted (LCC refers to the type of resonant converter, because its resonator is composed of an inductor L and two capacitors C, it is called LCC resonant converter). The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, an LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS (Metal-Oxide-Semiconductor) tube, but also reduces the on-off loss of MOS tube. The PFM-PWM composite control strategy and LADRC algorithm not only improve the power efficiency of the drive power supply, suppress the output current ripple, but also ensure that the output current of the drive power supply is stable when the input voltage, load and parasitic parameters of the circuit change. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0–40 A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness. [ABSTRACT FROM AUTHOR]

This paper proposes a self-supplied power management system to efficiently rectify and regulate the AC voltage received from wireless power transmission techniques to power or recharge biomedical devices. The proposed power management system comprises three integrated functional units, namely, a fully cross-coupled rectifier, a self-biased reference voltage, and a capacitor-less low-dropout regulator (LDO). To reduce the current complexity of designing capacitor-less LDOs, a new architecture based on a pair of diode-connected transistors at the load of the LDO is devised which alleviates the need for a large load capacitor. The proposed power management system is implemented in a 65-nm CMOS process with an active chip area of 0.0810 mm2. Experimental results indicate that this system is capable of rectifying an AC signal up to 5 V at a frequency of 6.78 MHz. This rectified signal is then regulated to a fixed DC voltage of 1.75 V, while the load current can vary between 0 and 75 mA, with a maximum voltage dropout of 170 mV. Advantageously, the proposed power management system is significantly robust to temperature, as a 55 °C change in ambient temperature leads to only a 9% degradation in its overall performance. Furthermore, the ability of the power management system to drive low-power consumer electronics is demonstrated, and its superiority is evidenced by a performance comparison with the latest integrated power management systems presented in the literature. [ABSTRACT FROM AUTHOR]

Controlling a PWM rectifier can be challenging due to the bilinear nature of its averaged model. This paper introduces the use of the Butterworth approach to design and control an LCL-filter-based PWM rectifier with power quality functions. By leveraging the linear part of the system, this approach reduces the number of variables involved in the control scheme. The rectifier is designed and controlled in a concatenated manner to ensure proper performance even during demanding power-quality events. The uniqueness of this approach lies in the fact that a fourth-order model can be regulated by using solely three-state variables and linear techniques founded on Butterworth polynomial synthesis. This approach differs from previous methods in that it does not employ nonlinear controllers, dq transformations, or double control loops. Hence, this divergent approach contributes to the simplification of power converter design and control through the application of the same polynomial synthesis, besides enhancing system operation in demanding scenarios. Extensive SIL simulations of a 1 kW, 220 Vrms PWM rectifier using the OPAL-RT-1400 platform were conducted to demonstrate the feasibility of the proposed controller. The selected tests reveal the validity of this proposal even when the PWM rectifier faces multiple power quality events simultaneously. [ABSTRACT FROM AUTHOR]

Research indicates that phase-to-ground short-circuits in a frequency converter can subject the rectifier diode and IGBT to excessive voltage and current, potentially causing damage if the component selection margin during hardware design is insufficient. In order to solve the above problems, this paper studies the design of the LCL filter and ground short circuit problem of the hundred-kilowatt inverter. Firstly, an analytical method for calculating the DC bus capacitance and reactor of the inverter is proposed. The interaction between the DC bus capacitance and the reactor parameters and performance is considered in the implementation process. The parameters of the DC bus capacitor and reactor are given. Secondly, the one-to-ground short circuit of the inverter is studied, and the energy flow mode and mathematical expression of the double boost circuit, considering the influence of the leakage inductance of the power transformer, are given. Based on the above analysis, a method for determining the rectifier diode and IGBT, considering the one-to-ground short circuit of the inverter, is proposed. Finally, a one-hundred-kilowatt inverter is developed, and the corresponding experiments are carried out. The feasibility of the proposed scheme is verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

This paper presents the deployment of a hybrid energy harvesting system that combines a wireless energy harvesting (EH) system and a 6 V, 170 mA monocrystalline solar energy derived from the Sun's rays. The hybrid energy harvesting (HEH) system comprises the rectifier, the solar cell panel, the charging circuit, and the EM4325 embedded RFID tag. This study aims to design an efficient EH system capable of increasing the read range of an active RFID tag. The proposed approach integrates a meandered line radio frequency identification (RFID) tag with an EM4325 IC chip as the receiver antenna. A halfwave doubler RF rectifier circuit is connected to the antenna using a 50 Ω SMA connector to convert the captured RF waves into usable electrical power. A solar energy charging module equipped with a Maximum Power Point Tracking (MPPT) system, a rechargeable lithium-ion battery, and a DC-DC converter is configured to manage and store the harvested energy efficiently. The UHF tag antenna operates at 919 MHz, achieving a peak gain of 3.54 dB. The proposed rectenna achieves a maximum measured harvested power conversion efficiency (PCE) of 55.14% for an input power (Pin) of 15 dBm at a distance of 5.10 cm, while the solar cell panel realizes 3.92 W of power. Experimental results demonstrate the hybrid harvester system's effectiveness, achieving a PCE of 86.49% at an output voltage (VDC) of 5.35 V. The main advantage of this approach is the creation of a compact hybrid RF and solar EH system by combining the solar cell panel with the antenna, thus enabling multi-functionality. [ABSTRACT FROM AUTHOR]

The precision of deadbeat direct power control depends on the parameters of the system model. In wide frequency applications, such as multi- electric aircraft and electric vehicles, variations in frequency and resistive parameters will affect the control effect. The AC side voltage frequency of the generator rectifier varies widely, which will lead to a steady-state reactive power error in the deadbeat direct power control. In addition, the large temperature variation range during the operation of the multi-electric aircraft and electric vehicles leads to large changes in the filter inductance and line resistance of the AC side, and the model parameters do not match the actual parameters, which will further deteriorate the control accuracy. In this paper, a PWM rectifier control method is proposed for the occasions when the frequency and temperature change are in a wide range. Using repetitive control and power compensation, it solves the problems of steady-state reactive power error and control accuracy degradation caused by the mismatch of model parameters under severe operating conditions. The control method can precisely adjust the output DC voltage of PWM rectifier, and it also can maintain unity power factor and reduce the total harmonic distortion rate of the input current. The effectiveness of the proposed control method is verified by the experimental results. [ABSTRACT FROM AUTHOR]

Failure of the high-voltage diode rectifier caused by lightning will cause huge losses. The traditional analysis of overvoltage induced by the high-voltage diode rectifier shell under lightning stroke cannot adapt to the overvoltage process caused by lightning stroke-induced conduction invading the inside of the high-voltage diode rectifier. Therefore, this paper proposes to establish a high-frequency equivalent model of the core components of the high-voltage diode rectifier, including diodes, reactors, transformers, and overhead lines. On this basis, a lightning overvoltage model of lightning-induced conduction into the high-voltage diode rectifier is built, and the transient process of diode lightning overvoltage under the constraint of reverse recovery charge is analyzed. Then, we describe the transient distribution of overvoltage in high-voltage diode rectifiers caused by lightning stroke. The transient distribution of overvoltage induced by lightning in series diodes under different diode equivalent models is analyzed by simulation. The simulation results show that the inconsistent parameters of series diodes can easily lead to diode damage due to uneven voltage distribution when lightning strikes. Therefore, this paper puts forward a scheme to reduce lightning damage, including selecting diodes with the same parameters and adding fast-melting fuses at the transformer's secondary side and in front of the series diode bridge arm. The simulation shows that the scheme proposed in this paper can effectively prevent the high-voltage diode rectifier from being damaged by lightning strikes. [ABSTRACT FROM AUTHOR]

This paper presents the theoretical analysis, experimental results and generalized structure for N modules of an isolated dc–dc SEPIC converter. The structure comes from the integration of N conventional SEPIC converters based on the input-series and output-parallel connection. The main advantages provided by the proposed structure are reduced voltage stress across the semiconductors and division of the current stress in the output diodes. The proposed converter is presented in a generalized approach, varying the voltage stress across the semiconductors according to the number of modules used. As the converter uses more than one switch, the commands can be either equal or phase-shifted by 360 ∘ / N degrees. When operating with phase-shift modulation, a multilevel converter is obtained, which brings another advantage of the structure, since there is a reduction in the volume of the input inductors ( L i 1 and L i 2 ) and the output capacitor ( C o ). In this paper, the steady-state analysis, a dynamic model, system control and experimental results are presented for phase-shift modulation and discontinuous conduction mode (DCM). The performance of the proposed converter was verified in a prototype with four modules and the following specifications: 500 W output power, 800 V input voltage, 120 V output voltage and 50 kHz switching frequency. The converter achieved 94.42% efficiency at rated power. [ABSTRACT FROM AUTHOR]