Search

This paper proposes a single-phase, transformer-less, seven-level inverter that utilizes eight switches, three capacitors, and two diodes to produce seven voltage levels with triple boosting ability. The availability of the common-ground point eliminates the leakage current in PV applications. The proposed Transformer-Less Triple-Boosting Seven-Level Inverter (TLTB7LI) has the ability to feed different types of loads from non-unity to unity power factors. The voltage balancing of capacitors takes place naturally without the need for auxiliary circuits and complicated control strategies. This paper investigates the appropriateness of the proposed TLTB7LI for grid-connected application. The Peak Current Controller (PCC) is employed to generate the switching pulses and regulate the active/reactive power transfer between the converter and the output, which guarantees the high quality of injected current to the output. Moreover, the operational principles, its control technique, as well as the design procedure of the key components of the proposed inverter have been presented. The superiority of the proposed inverter over existing counterparts has been verified through comparative analysis. The simulation and experimental analysis validated the proper operation of the proposed TLTB7LI. [ABSTRACT FROM AUTHOR]

The main contribution of this paper is to present a simple algorithm that theoretically and numerically assesses the switching angles of an inverter operated with the SPWM technique. This technique is the most widely used for eliminating harmonics in DC-AC converters for powering motors, renewable energy applications, household appliances, etc. Unlike conventional implementations of the SPWM technique based on the analog or digital comparison of a sinusoidal signal with a triangular signal, this paper mathematically performs this comparison. It proposes a simple solution to solve the transcendental equations arising from the mathematical analysis numerically. The technique is validated by calculating the total harmonic distortion (THD) of the generated signal theoretically and numerically, and the results indicate that the calculated angles produce the same distribution of harmonics calculated analytically and numerically. The algorithm is limited to single-phase inverters with unipolar SPWM. [ABSTRACT FROM AUTHOR]

Power systems with a high proportion of inverter-based sources like photovoltaics require a substantial short-circuit current ratio to ensure strong voltage support capabilities. However, this also increases the system's short-circuit current capacity and levels, which may potentially affect the safe operation of system equipment and current-carrying conductors. To evaluate the operational risks, this paper proposes a quantitative calculation model for the critical integration proportion of grid-connected inverter-interfaced power sources based on short-circuit current over-limit probability. Firstly, according to the verification criterion about short-circuit current during the selection of the switching equipment and conductors in the power system, the short-circuit current over-limit probability evaluation system with five indices is established. Secondly, considering the impact of the increased grid integration proportion of inverter-based power sources on short-circuit currents, an evaluation process for operational risk probabilities is proposed. Based on this, the critical access proportion for inverter-based power source integration in the power grid can be calculated. Finally, the proposed model is used to assess the operational risk probability for a 220 kV system which includes a high proportion of inverter-based power sources in the Anhui area, China. Through the analysis of cumulative probability distribution curves, the critical grid integration proportion interval for the transition from normal to high proportion stages of inverter-based power sources is determined. [ABSTRACT FROM AUTHOR]

The phase circulating current (PCC) of the parallel three-phase inverter systems dramatically affects the power quality and conversion efficiency of the power grid. In this paper, a composite suppression strategy is proposed to solve the PCC issue by using the sliding mode control (SMC) approach and improved virtual impedance droop control. Taking the commonly used 2-group parallel three-phase inverter as an example, an inter- and intra-classification model is established by analyzing the sources of PCC. In order to suppress the inter-PCC, the traditional virtual impedance droop control is given, following the improved substitute by combining SMC. And the variables of the bus voltage, Q-U loop, P-f loop, and the virtual-induced reactance are also introduced for the robust control of the impedance droop. On the other side, a SMC-based suppression approach is designed to solve the issue of the intra-PCC. Its idea is to introduce a regulation factor for the space vector pulse width modulation (SVPWM) so that the zero-sequence voltage can be eliminated and the influence of the intra-PCC can be relieved. Comparative simulations and experiments validate the effectiveness of the methods proposed in this paper. [ABSTRACT FROM AUTHOR]

In order to reduce the sampling delay and improve bandwidth, sability margin, and the robustness of the active damping in LCL-filtered grid-connected inverters, real-time sampling provides a convenient method. However, aliasing is easily introduced in the control loop because of high-frequency switching harmonics, resulting in a rise in low-order harmonics. To address the challenge of aliasing under real-time sampling, a new method based on multisampling and mean filtering is proposed by combining the proposed harmonic detection and control methods in this paper. This method works by sampling and controlling the fundamental current and selective subharmonic currents separately. The fundamental current control loop without any additional filters maintains real-time sampling, while multisampling and mean filters are applied to the harmonic current control loop. The proposed control method can not only improve the dynamic response performance and control stability of the system but also effectively suppress the selective low-order current harmonics and the aliasing of sampling. Finally, the correctness of the proposed sampling scheme and control strategy is verified by the simulation based on R2018b, MathWorks, Natick, MA, USA and an experimental prototype of a three-phase grid-connected photovoltaic inverter rated at 230 V/50 Hz/40 kW. [ABSTRACT FROM AUTHOR]

The work is based on a collaboration between Hiroshima University and Kure KOSEN College. This paper presents the design concept, hardware, and applications of a single-phase synchronous inverter (SSI), a specially designed grid-forming inverter (GFM) for single-phase micro-grid (SMGs). The SSI is designed for the conventional 100/200 V distribution network and is based on the concept of "Non-Interference Core (NIC) dynamic model". Novel contributions of this paper are: (1) A root mean square (RMS) model of NIC-SSI was developed, combined with the conventional power system model, and verified through the comparison with the hardware-in-the-loop (HIL) simulation and SSI hardware experiments; (2) using the developed RMS simulation tool, the stabilization effect of the SSIs was investigated in condition under which the SSIs are massively installed in a distribution system; (3) off-grid SMG operations using SSIs under various ill-conditioned loads were demonstrated. The results show that the SSI has the considerable ability of grid stability enhancements for frequency, transient, and small-signal stabilities. The proposed SMG using SSIs is promising. [ABSTRACT FROM AUTHOR]

The growth of renewables in public energy networks requires suitable strategies to assess the stable operation of the respective power electronic devices, e.g., inverters. Different assessment methods can be performed with regard to the available knowledge and the assessment objective, e.g., a specific frequency range or the input signal characteristics that are typically classified into small-signal and large-signal disturbances. This paper addresses the limits of the measurement-based small-signal stability analysis in the harmonic frequency range of commercially available single-phase inverters for photovoltaic applications. The harmonic stability is analyzed, and the results for a sinusoidal background voltage and distorted background voltages are assessed based on measurements. The measurements prove that even in the harmonic frequency range, the harmonic stability analysis can only provide a sufficient but not a necessary condition in terms of the statement towards an instable operation. [ABSTRACT FROM AUTHOR]

To reduce the influence of voltage harmonics on the grid current, a control strategy based on adaptive quasi-proportional phase compensated resonance (QPR_PC) is proposed. Firstly, the LCL grid-connected photovoltaic inverter system model is established, and the stability performance of the three-level inverter system under double closed-loop control is analyzed using the output impedance model of the inverter. Then, a QPR regulator for the zero steady-state error tracking of AC signals is studied. To solve the problem that the system has poor robustness against frequency changes when the traditional QPR regulator is used in the static coordinate system, this paper improves the traditional QPR regulator to optimize the response characteristics of the closed-loop system. Based on the QPR regulator, a phase margin compensation structure is introduced to form QPR_PC control. Then adaptive frequency design is added to ensure good control even when the power grid frequency drifts, which is the control strategy proposed in this paper. Verification shows that the proposed method improves the phase margin of output impedance at a specific frequency, restrains the interference of the 3rd, 5th, and 7th harmonics of grid voltage, and improves the dynamic performance of the system and the quality of grid-connected current. Finally, the simulation results show that the total harmonic distortion rate of grid-connected current is reduced by 1.03% after adopting this strategy, which verifies the effectiveness and correctness of the proposed method. [ABSTRACT FROM AUTHOR]

In order to quantitatively analyze the electromagnetic exposure dose of an inverter in a pure electric vehicle to the driver's body and assess the safety of the electromagnetic exposure, based on a real human anatomy model in the virtual home project, a real human model with several organs and tissues, including muscles, bones, a heart, lungs, a liver, kidneys, a bladder, a skull, a scalp, white matter, and a cerebellum, was constructed. The inverter of a pure electric vehicle is considered to be the electromagnetic exposure source; for this study, an equivalent electromagnetic environment model composed of a real human body, an inverter, and a vehicle body was built. The distribution of induced fields in the driver's tissues and organs was calculated and analyzed using the finite element method. The results show that the distribution of the magnetic flux density, induced electric field, and induced current density in the driver's body was affected by the spatial distance of the inverter. The farther the distance was, the weaker the value was. Specifically, due to the different dielectric properties of the different tissues, the induced field in the different tissues was significantly different. However, the maximum magnetic flux density over the space occupied by the driver's body and induced electric field in the driver's trunk and central nervous system satisfied the exposure limits of the International Commission on Non-Ionization Radiation Protection, indicating that the electromagnetic environments generated by the inverter proposed in this paper are safe for the vehicle driver's health. The numerical results of this study could also effectively supplement the study of the electromagnetic environments of pure electric vehicles and provide some references for protecting the drivers of pure electric vehicles from electromagnetic radiation. [ABSTRACT FROM AUTHOR]

With the increased grid-connected capacity of a single-phase distributed power supply, three-phase power unbalance is more likely to occur in a power grid. Three-phase power unbalance can further lead to three-phase voltage unbalance, which can have adverse effects on power quality and power supply reliability. Therefore, there is a need to build a three-phase power transmission channel to realize power exchanging among phases. In this paper, a novel grid-connected inverter control strategy for three-phase power exchanging is proposed based on constructed negative sequence current control. A completed negative sequence current control loop is added to a conventional three-bridge inverter to realize the decoupling control of three-phase grid current, and then three-phase power exchanging is realized. On this basis, this paper further puts forward a strategy for three-phase power exchanging aimed at three-phase voltage balance. Correspondingly, the three-phase grid current is controlled according to the feedback of the three-phase voltage. Then, three-phase voltage balance is achieved by three-phase power exchanging. The simulation and experimental results show that the proposed strategy is suitable for a three-phase unbalanced power grid, which can realize three-phase power exchanging, and further, can achieve three-phase voltage balance. The proposed strategy can help to improve power quality and supply reliability. [ABSTRACT FROM AUTHOR]

The negative-sequence current component and harmonic components generated when an asymmetrical fault occurs in the power grid seriously affect the normal operation of the photovoltaic (PV) grid-connected inverter. In order to suppress the negative-sequence current component and the harmonic component of the grid-connected current, and to meet the normal grid-connected operation requirements of the PV grid-connected inverter when asymmetrical faults occur in the grid, this paper proposes the proportional integral double-resonant (PI-DR) current controller, which consists of the PI controller and double-resonant controllers. The PI-DR current controller can directly control the negative-sequence current component and the grid-connected current harmonic component in the output current in the forward synchronous rotating coordinate system, without decomposing the positive and negative sequence currents. The PI-DR current controller ensures that the PV grid-connected inverter can realize normal grid-connected operation and improves the quality of the power when an asymmetrical fault occurs in the power grid. MATLAB/Simulink experiments show that the PI-DR current controller can improve the dynamic characteristics of the PV grid-connected inverter and improve the operating capability of the system when an asymmetrical fault occurs in the power grid. [ABSTRACT FROM AUTHOR]

In the neutral point clamped (NPC) three-level inverter-permanent magnet synchronous motor system, traditional model predictive current control (MPCC) uses the system predictive model to traverse the 27 basic voltage vectors, to achieve the d-q axis current component and neutral point voltage of the multi-objective optimal control. Finite control set model predictive control predicts the state change of the control target at future moments based on a finite number of switching states of the inverter. The control principle of this method is simple and easy to implement, but the control effectiveness of this control strategy is limited because only one basic vector can be selected as the optimum output per control period. In this paper, a model predictive current control strategy based on an extended control set (ECS-MPCC) is proposed, which can improve the control performance of the system by extending the control set to select multiple vectors in a single control period compared to the traditional strategy. In addition, to address the disadvantage of extending virtual space vectors leading to an increase in computation, this paper proposes a fast search method for optimal vector based on region reduction. The proposed method avoids the optimization process traversing all virtual space vectors, thus enabling a fast search for the optimal vector. The experimental results show that the proposed control strategy has good steady-state and dynamic performance. [ABSTRACT FROM AUTHOR]

Many advanced power electronics control techniques present a steep computational load, demanding advanced controllers, such as FPGAs. However, FPGA development is a daunting and time-consuming task, inaccessible to most users. This paper proposes a complete methodology for prototyping power electronics with Xilinx Zynq-based boards using Matlab/Simulink and HDL Coder. Even though these tools are relatively well documented, and several works in the literature have used them, a methodology for developing power electronics systems with them has never been proposed. This paper aims to address that, by proposing a complete programming and design methodology for Zynq-based power electronics and discussing important drawbacks and hurdles in Simulink/HDL Coder development, as well as their possible solutions. In addition, techniques for the implementation of all required peripherals (ADCs, digital outputs, etc.), system protections, and real-time data acquisition on Zynq boards are presented. This methodology considerably reduces the development time and effort of power electronics solutions using Zynq-based boards. In addition, a demonstration Simulink model is provided with all proposed techniques and protections, for use with a readily available development board (Zedboard) and ADC modules. This should further reduce the learning curve and development effort of this type of solution, contributing to a broader access to high-performance control prototyping using Zynq-based platforms. An application example is presented to demonstrate the potential of the proposed workflow, using a Zedboard to control a multilevel UPS inverter prototype with Model Predictive Control. [ABSTRACT FROM AUTHOR]

In weak grid, feedforward of grid voltage control is widely used to effectively suppress grid-side current distortion of inverters caused by harmonics in point of common coupling (PCC) voltage. However, due to its introduction of a positive feedback loop related to the grid impedance, it results in a significant reduction in the system phase margin. In view of this, in this paper, the output impedance of a three-phase LCL grid-connected inverter under a quasi-proportional resonant (QPR) controller is first modeled. Instead of the traditional grid voltage feedforward control strategy, a band-pass filter is added to the grid voltage feedforward channel. Secondly, a multi-objective constraint method is proposed to make improvements to the feedforward function. Then, a multi-objective constraint function is established with the constraints of base-wave current tracking performance, system stability margin, and low-frequency amplitude, and the feasibility of its function optimization design method is verified. Theoretical analysis shows that the optimized grid voltage feedforward control strategy can effectively reshape the phase characteristics of the system output impedance, which greatly broadens the adaptation range of the system to the grid impedance. Finally, the effectiveness of the proposed control strategy is verified by building a semi-physical simulation experimental platform based on RT-LAB OP4510. [ABSTRACT FROM AUTHOR]

In this paper an efficient, compact, and cheap power source design for an off-grid PV water pumping system is investigated. The proposed system consists of a PV array, battery, three-port converter (TPC), three-phase voltage source inverter, and induction motor pump. Power is extracted from PV sources during the daytime and used to charge batteries through the three-port converter, then used later to supply load during the nighttime. An intelligent MPPT method is used to obtain PV maximum power; a jellyfish optimization technique with different control algorithms is used to optimize and tune controllers' parameters among the system. Different modes for the TPC are discussed depending on PV power availability. The proposed system is simulated to assess system performance under different conditions; also the system is efficient with reduced number of components than conventional converters. A complete unified power management over PV input port, battery port, and load port has occurred for all operation modes. At all operation modes, the system has been feeding load without any unmet loads. A real case study in Al-Kharijah oasis is studied and simulation results are listed; for the Dom case DC bus ripple factor voltage percentage equals 0.8%, in the Dim case equals 3%, and in the Siso mode equals 9%. [ABSTRACT FROM AUTHOR]

This paper proposes a control strategy for grid-following inverter control and grid-forming inverter control developed for a Solar Photovoltaic (PV)–battery-integrated microgrid network. A grid-following (GFL) inverter with real and reactive power control in a solar PV-fed system is developed; it uses a Phase Lock Loop (PLL) to track the phase angle of the voltages at the PCC and adopts a vector control strategy to adjust the active and reactive currents that are injected into the power grid. The drawback of a GFL inverter is that it lacks the capability to operate independently when the utility grid is down due to outages or disturbances. The proposed grid-forming (GFM) inverter control with a virtual synchronous machine provides inertia to the grid, generates a stable grid-like voltage and frequency and enables the integration of the grid. The proposed system incorporates a battery energy storage system (BESS) which has inherent energy storage capability and is independent of geographical areas. The GFM control includes voltage and frequency control, enhanced islanding and black start capability and the maintenance of the stability of the grid-integrated system. The proposed model is validated under varying irradiance conditions, load switching, grid outages and temporary faults with fault ride-through (FRT) capability, and fast frequency response and stability are achieved. The proposed model is validated under varying irradiance conditions, load switching, grid outages and line faults incorporating fault ride-through capability in GFM-based control. The proposed controller was simulated in a 100 MW solar PV system and 60 MW BESS using the MATLAB/Simulink 2023 tool, and the experimental setup was validated in a 1 kW grid-connected system. The percentage improvement of the system frequency and voltage with FRT-capable GFM control is 69.3% and 70%, respectively, and the percentage improvement is only 3% for system frequency and 52% for grid voltage in the case of an FRT-capable GFL controller. The simulation and experimental results prove that GFM-based inverter control achieves fast frequency response, and grid stability is also ensured. [ABSTRACT FROM AUTHOR]

Grid-forming inverters (GFMs) have emerged as crucial components in modern power systems, facilitating the integration of renewable energy sources and enhancing grid stability. The significance of GFMs lies in their ability to autonomously establish grid voltage and frequency, enabling grids to form and improve system flexibility. Discussing control methods for grid-forming inverters is paramount due to their crucial role in shaping grid dynamics and ensuring reliable power delivery. This paper explores the fundamental and advanced control methods employed by GFMs, explaining their operational principles and performance characteristics. Basic control methods typically involve droop control, voltage and frequency regulation, and power-balancing techniques to maintain grid stability under varying operating conditions. Advanced control strategies encompass predictive control, model predictive control (MPC), and adaptive control, which influence advanced algorithms and real-time data for enhanced system responsiveness and efficiency. A detailed analysis and performance comparison of different control methods for GFM is presented, highlighting their strengths, limitations, and suitability for diverse grid environments. Through comprehensive studies, this research interprets the ability of various control strategies to mitigate grid disturbances, optimize power flow, and enhance overall system stability. [ABSTRACT FROM AUTHOR]

This paper presents a new electric drive-reconfigured on-board charger and initial electromagnetic torque suppression method. This proposed reconfigured on-board charger does not need many components added to the original electric drive system: only a connector is needed, which is easy to add. Specifically, the inverter for propulsion is reconfigured as a buck chopper and a conduction path to match the reconfigured windings. Two of the machine phase windings serve as inductors, while the third phase winding is reutilized as a common-mode inductor. In addition, the initial charging torque is generated at the outset of the charging process, which may cause an instant shock or even rotational movement. In order to prevent vehicle movement, the reason for the charging torque and suppression method were analyzed. Further, predictive control of the model based on mutual inductance analysis was adopted, where the charging torque was directly used as a control object in the cost function. Finally, experimental performances were applied to verify the proposed reconfigured on-board charger under constant current and constant voltage charging. [ABSTRACT FROM AUTHOR]

It is simple to implement conventional current control with a proportional integral (PI) controller. However, system stability and dynamic performance are not perfect, particularly when operating under unfavorable conditions. In this paper, an improved control method is proposed by introducing a compensation unit. The compensation unit can effectively compensate the system's phase around the crossover frequency, greatly enhancing the system's phase margin and stability. It is also capable of handling weak-grid conditions. In this paper, the concept of the proposed compensation unit is explained first. Then, the corresponding mathematical model for the current control loop is built, and system bode diagrams for the conventional and proposed methods are compared. Furthermore, the effect of the parameters for the compensation unit is investigated, and an optimization method is proposed to determine optimal parameters. In addition, to handle weak-grid conditions, the proposed scheme is expanded by including the compensation unit in the grid's feed-forward loop. Finally, an experimental platform is constructed, and the experimental results are presented to validate the proposed method. [ABSTRACT FROM AUTHOR]

In recent years, there has been a trend toward expanding the operating frequency range and increasing the output power of Sound Navigation and Ranging (SONAR) systems to enhance their acoustic detection capabilities. However, due to this increase in operational power, the electrical capacity of amplifiers for SONAR system operation also increases, necessitating High-Power Amplifiers. When configured with a single amplifier, as in conventional methods, the volume of amplifiers increases due to volumetric increases in heat dissipation, components, and windings. These issues are detrimental to SONAR amplifier installation, mobility, maintenance, and equipment lifespan due to stress on individual components. Additionally, amplifiers for SONAR systems are comprised of power conversion devices, transformers for LC filters and matching, necessitating consideration of LC filters and matching transformers for enhancing voltage quality and efficiency to improve amplifier performance transmitted to SONAR transducers. However, previous research has focused on single-amplifier design methods, neglecting such considerations. Therefore, this paper proposes a design technique that overcomes the drawbacks of using the conventional design method by configuring multiple H-bridge inverters in a cascade format and utilizes one of the optimization algorithms, Particle Swarm Optimization (PSO), to derive amplifier design techniques that optimize component parameters for enhancing high-capacity amplifier performance. Subsequently, theoretical analysis, simulations, and experimental results comparing the proposed high-power amplifier design method with conventional single-amplifier design methods demonstrate similar error rates in operational frequency bands. [ABSTRACT FROM AUTHOR]

Compared with the traditional grid-following photovoltaic grid-connected converter (GFL-PGC), the grid-forming photovoltaic grid-connected converter (GFM-PGC) can provide voltage and frequency support for power systems, which can effectively enhance the stability of power electronic power systems. Consequently, GFM-PGCs have attracted great attention in recent years. When an asymmetrical short-circuit fault occurs in the power grid, GFM-PGC systems may experience transient instability, which has been less studied so far. In this paper, a GFM-PGC system is investigated under asymmetrical short-circuit fault conditions. A novel Q-V droop control structure is proposed by improving the traditional droop control. The proposed control structure enables the system to accurately control the positive- and negative-sequence reactive current without switching the control strategy during the low-voltage ride-through (LVRT) period so that it can meet the requirements of the renewable energy grid code. In addition, a dual-loop control structure model of positive- and negative-sequence voltage and current is established for the GFM-PGC system under asymmetrical short-circuit fault conditions. Based on the symmetrical component method, the composite sequence network of the system is obtained under asymmetrical short-circuit fault conditions, and positive- and negative-sequence power-angle characteristic curves are analyzed. The influence law of system parameters on the transient synchronous stability of positive- and negative-sequence systems is quantitatively analyzed through the equal area criterion. Finally, the correctness of the theoretical analysis is verified by simulation and hardware-in-the-loop experiments. [ABSTRACT FROM AUTHOR]

The increasing popularity of electric drives employing an isolated dual-inverter (DI) topology is motivated by their superior DC-link voltage and power utilization, fault-tolerant operation, and potential for multilevel operation. These attributes are significant in battery-powered transportation, such as electric vehicles and aviation. Given the considerable freedom in modulation and control of the DI topology, this paper researches the impact of reference voltage vector distribution between the two individual inverters. The study also evaluates the influence of two well-established asynchronous modulation strategies—Space Vector PWM (SVPWM) and Depenbrock's Discontinuous Modulation (DPWM1). Since simulation tools nowadays play a crucial role in power electronics design and concept verification, the results are based on extensive and detailed models in Matlab/Simulink. Employing the basic field-oriented control of a 12 kW induction motor with precisely parameterized SiC switching devices for accurate loss calculation, this research reveals the possibility of significant energy savings at multiple operating points. Notably, optimal efficiency is achieved when one inverter operates up to half of the nominal speed while the other solely establishes a neutral point for the winding. Moreover, the results highlight DPWM1 as a superior strategy for the DI topology, showcasing reduced converter losses. Overall, it is shown that the system's losses can be significantly reduced just by the design of the voltage vector distribution in the drive's operating range and the modulation strategy selection. [ABSTRACT FROM AUTHOR]

The operation of parallel inverters in microgrids is an important way to expand system capacity, but there are problems of circulating current fluctuations and power sharing errors in parallel inverters' operation. In this paper, a parallel operation strategy for inverters based on improved adaptive droop control and Equivalent Input Disturbance (EID) is proposed. Firstly, the model and control topology of parallel inverters are presented. Secondly, in order to solve the power sharing error caused by impedance difference and the voltage drop caused by virtual impedance, a reference voltage generator based on improved adaptive droop control is proposed. Then, considering the circulating current fluctuation as a disturbance, a voltage controller based on an equivalent input disturbance approach is proposed to reduce the disturbance. Finally, simulation in MATLAB/Simulink is carried out to verify the effectiveness of the parallel operation strategy. [ABSTRACT FROM AUTHOR]

The integration of communication infrastructures into traditional power systems, transforming them into cyber-physical power systems (CPPS), accentuates the significance of communication in influencing system performance and sustainability. This paper presents a versatile, innovative cyber-physical co-simulation framework that integrates the physical power system and communication networks, uniting OPAL-RT, a network simulator (ns3), and Docker containers into a sophisticated platform, facilitating intensive studies into CPPS dynamics. The proposed experimental study provides an innovative way to assess the frequency control response of a cyber-physical inverter-based microgrid (MG), addressing the MG sustainability challenges. We consider diverse real-world scenarios, focusing on communication delays and distributed denial of service (DDoS) attacks within the communication channels. We propose a precise ns3-based communication model that bridges the MG's primary and secondary control layers, an aspect often overlooked in previous studies; this is a noteworthy contribution to elucidating the adverse impacts of communication latency on MG frequency performance. The experimental results demonstrate the effectiveness of the centralized secondary controller in eliminating the frequency deviations. Furthermore, the findings offer insights into stable and unstable regions, revealing how the communication delay value affects the frequency stability under different operating conditions. In addition, the developed real-time DDoS attacks model within the proposed communication surface unveils crucial insights into the MG's resilience to cyber threats. This work's revelations offer a foundational awareness of MG vulnerabilities, paving the way for designing robust and resilient communication networks and control strategies within the cyber-physical inverter-based microgrids. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems are becoming essential to our energy landscape as renewable energy sources become more widely integrated into power networks. Preserving grid stability, especially during voltage sags, is one of the significant difficulties confronting the implementation of these technologies. This attribute is referred to as low-voltage ride-through (LVRT). To overcome this issue, adopting a Proportional-Integral (PI) controller, a control system standard, is proving to be an efficient solution. This paper provides a unique algorithm-based approach of the Marine Predator Algorithm (MPA) for optimized tuning of the used PI controller, mainly focusing on inverter control, to improve the LVRT of the grid, leading to improvements in the overshoot, undershoot, settling time, and steady-state response of the system. The fitness function is optimized using the MPA to determine the settings of the PI controller. This process helps to optimally design the controllers optimally, thus improving the inverter control and performance and enhancing the system's LVRT capability. The methodology is tested in case of a 3L-G fault. To test its validity, the proposed approach is compared with rival standard optimization-based PI controllers, namely Grey Wolf Optimization and Particle Swarm Optimization. The comparison shows that the used algorithm provides better results with a higher convergence rate with overshoot ranging from 14% to 40% less in the case of DC-Link Voltage and active power and also settling times in the case of MPA being less than PSO and GWO by 0.76 to 0.95 s. [ABSTRACT FROM AUTHOR]

Electric vehicles are the most innovative and promising area of the automotive industry. The efficiency of a traction battery is an important factor in the performance of an electric vehicle. This paper presents a mathematical model of an electric truck, including modules for the traction battery to determine the depth of battery discharge during the operation of the electric truck, a traction electric system for the electric truck and a system for calculating traction forces on the shaft in electric motors. As a result of the modelling, the charging and discharging currents of an accumulator battery in a real cycle of movement in peak and nominal modes of operation in electric motors and at different voltages of the accumulator battery are determined. A functional scheme of a generalized model of the electric vehicle traction electrical equipment system is developed. An experimental battery charge degree, torques of asynchronous electric motors, temperature of electric motors and inverters, battery voltage and the speed of electric motors have been measured and analysed. The developed complex mathematical model of an electric vehicle including a traction battery, two inverters and two asynchronous electric motors integrated into an electric portal bridge allowed us to obtain and study the load parameters of the battery in real driving cycles. Data were verified by comparing simulation results with the data obtained during driving. [ABSTRACT FROM AUTHOR]

In general, severe load imbalances in small AC micro-grid systems can degrade their operational performance and their maintenance. This is because the unbalanced load in the micro-grid affects the energy flow and the voltage regulation functions of each phase. In order to solve the voltage imbalance problem, several algorithms for the 3-phase 4-leg CVCF inverter have been proposed, but the control algorithms are not enough to operate the 4-leg CVCF inverter in a stable manner. Therefore, this paper proposes a single-phase voltage and power control algorithm for the 3-phase 4-leg CVCF inverter based on a dq control in order to improve the voltage imbalance problem caused by a severely unbalanced load, where the single phase voltage control algorithm is composed of an αβ-dq and a dq-αβ transformer, a voltage and a current controller, and an off-set controller and a PWM, and the single-phase power control algorithm is also composed of an αβ-dq and a dq-αβ transformer, an active/reactive power and a current controller, and an off-set controller and a PWM. Additionally, this paper performs modeling of the single-phase voltage and the power controller for a 4-leg CVCF inverter using the Matlab/Simulink S/W. From the simulation results, it is confirmed that the transient stability of the proposed single voltage control algorithm can be improved compared to the conventional control algorithm, and voltage control can also be maintained in a stable manner under extremely unbalanced conditions. Further, it is confirmed that 3-phase currents of the proposed single-phase power control algorithm are controlled in a stable manner under extremely unbalanced conditions. [ABSTRACT FROM AUTHOR]

Energy crises and the growth of the energy demand have increased the interest in utilizing unconventional power sources. Thus, renewable energy sources have become a topic of interest to mitigate rising energy concerns and cope with increased electricity demand. With remarkable merits including cleanness and abundance, photovoltaic (PV) solar energy systems are a key to solving these issues. The employed inverters should effectively utilize the maximum available power from the PV solar system and transfer this power to the utility grid without posing any further limitations. However, the unequal power generation of different PV systems caused by partial shading (PS) and other PV panel degradation factors leads to a reduction in generation capacity. One of the relatively new solutions to mitigate the mismatch concerns between the PV modules and sub-modules is to extract the maximum power of each sub-module individually. The main objective of this paper is to present a comprehensive review of such PV grid-connected inverters topologies associated with sub-module connection and control. It will classify the PV grid-tied inverters in accordance with the level where the maximum power point tracking (MPPT) system is implemented. A special focus has been placed on sub-module microinverters (MI) in terms of circuit topologies, conversion efficiency, and controller design. This paper provides a comprehensive analysis of employing the distributed MPPT (DMPPT) approach to maximize the power generation of PV systems by mitigating the mismatch issues inside the PV module. The circuit topology, PV system configuration, and MPPT algorithms used for applying DMPPT solutions in PV SMs are discussed in detail in this study. [ABSTRACT FROM AUTHOR]

Under the current trend of power electronics in energy systems, a high percentage of renewable energy transports clean energy to the grid through grid-connected inverters. The pulse-width modulation (PWM) technique brings high-order harmonics near to the switching frequency, and LCL filters with low-pass characteristics become the common choice for grid-connected inverters. However, the low-order harmonics caused by nonideal switching characteristics are difficult to filter out, and the new resonance point introduced by the LCL filter causes a security problem for the energy systems. Firstly, the generation mechanism of the 6 k ± 1 order harmonic and high-frequency resonance from a PV grid-connected inverter is analyzed. Then, a virtual resistor is constructed by the active damping method to absorb the resonant component. Meanwhile, this paper also presents an adaptive modulation voltage compensation method to decrease the low-order harmonics. Finally, the actual measured data of user photovoltaic (PV) and multiple comparative simulations verify these theories. Simulation results show that the proposed coordinated control algorithm reduces the peak of the resonance point, and the rate of low-order harmonics mitigation is more than 50%. The proposed method is suitable for various operating conditions. [ABSTRACT FROM AUTHOR]

The paper deals with a grid-connected single-phase battery charger integrated with photovoltaic generators (PVGs). The circuit topology consists of a multilevel architecture based on a Cascaded H-Bridge (CHB) rectifier. Its main task is to charge the batteries, primarily from the PVGs, by also assuring to keep their state-of-charge (SOC) balanced. Nevertheless, when the battery SOC overcomes a predefined upper limit, beyond which the charging process could be interrupted, the available PV power can no longer be transferred to the batteries. Therefore, to avoid an undesired curtailment of PV power production, this latter can be supplied to the grid by inverting the system operation. The paper shows how to achieve this result by implementing a dedicated control action based on a multi-step procedure. Numerical investigations are carried out on a 19-level CHB converter implemented in the PLECS environment to validate the feasibility and effectiveness of the proposed control technique. [ABSTRACT FROM AUTHOR]

The main aim of the research work presented in this paper consists of proposing an effective control scheme for a grid-connected single-phase photovoltaic (PV) system to enhance not only the power quality at the point of common coupling (PCC) but also to operate with a maximum power point tracking (MPPT) controller. Moreover, an orthogonal signal generator (OSG) module for effective grid synchronization, a current reference generation controller, and a PWM generating block have also been designed and included in this paper. The proposed control strategy allows the MPPT controller to switch to faulty mode and maintains the voltage according to network requirements using an adaptive neuro-fuzzy inference system (ANFIS)-based control whenever a fault occurs at the PCC. The performance of the analyzed control strategy, which is based on the static compensation of the DC-link voltage fluctuations in a grid-connected inverter powered by PV, is further explored through simulations in MATLAB, and the results are included in this paper. Moreover, the control scheme is implemented experimentally using a dSPACE DS 1104 control board and then assessed on a small laboratory-scale single-phase PV system that is subjected to some fault scenarios. The simulation and experimental results have shown improved power quality and robustness against grid fluctuations, resulting in better dynamic performance. [ABSTRACT FROM AUTHOR]

This paper introduces a mathematical design and analysis of three-phase inverters used in electric drive applications such as aerospace, electric vehicles, and pumping applications. Different wide bandgap (WBG) semiconductor technologies are considered in this analysis. Using SiC MOSFETs and Si IGBTs, two drive systems are developed in order to show the improvement in the efficiency of the inverter. The efficiency, total losses of the drive systems and the power losses of two inverters are computed and compared for both drive systems at the same operating condition. The drive system with SiC MOSFET shows much better performance compared to the drive system with Si IGBT. The SiC MOSFET system provides a 59.39%, 86.13%, and 29.76% lower conduction losses, switching losses and drive's total losses, respectively, compared to the Si IGBT system. The efficiency of the SiC MOSFET system is 2.46%pu higher than the efficiency of the Si IGBT drive system. Moreover, this paper introduces a detailed analysis for the dc-link voltage and current ripples in three-phase inverters. Furthermore, the minimal dc-link capacitor needed to deal with the ripple current and voltage is investigated. Finally, the performance of the drive with Si IGBT is experimentally tested under different operating speeds and loads. [ABSTRACT FROM AUTHOR]

In response to the problems of impedance variation and rich background harmonics in the weak grid environment of traditional LCL grid-connected inverters, which cause distortion of the grid-connected current and reduce the stability of the entire grid-connected system, this paper proposes a passive fuzzy-active disturbance rejection control strategy. Firstly, passivity-based control (PBC) is introduced into the grid-connected inverter system to ensure the global stability of the entire system. Secondly, in order to solve the problem of difficult selection of inverter-side current, active disturbance rejection control (ADRC) is used to directly track the grid-connected current, avoiding the tracking error of AC signal and suppressing the interference of background harmonics of grid voltage. The combination of fuzzy control and ADRC simplifies the system parameter tuning process, and the FUZZY-ADRC grid-connected current outer loop and PBC inductance current inner loop are combined to form a multi-loop control system. Finally, simulation comparison verifies that the proposed control strategy can effectively suppress the harmonics of grid-connected current, improve the quality of grid-connected current, and enhance the stability of the entire grid-connected system in a weak grid environment. [ABSTRACT FROM AUTHOR]

Repetitive control (RC), which can track any periodic signal with a known integer period with zero steady-state error, is widely used for current control of grid-tied inverters in microgrids. However, the inherent one fundamental period time delay, leads to poor dynamic performance. Furthermore, the performance of conventional RC (CRC) will degrade when operating at a high variation grid frequency. Therefore, this paper proposes a frequency adaptive improved RC (FA-IRC) for grid-tied inverters. The improved RC (IRC) consists of a repetitive controller with a modified internal model filter, plus a proportional controller. In comparison to the CRC, the IRC has a good dynamic response, because it provides a higher gain and a wider bandwidth at the resonant frequency. Moreover, to achieve the frequency adaptability of the IRC, a fractional delay, based on a finite impulse response (FIR) filter, is built into the IRC system, to ensure that the resonant frequency of the IRC is approximately equal to the actual grid frequency and harmonic frequency. Stability analysis and characteristic analysis of the FA-IRC system are reported in this paper. Simulations are conducted, to demonstrate the validity of the proposed method. [ABSTRACT FROM AUTHOR]

In response to the rapid changes in the international energy environment, developing renewable energy (RE)-based distributed generation (DG) and various smart micro-grid systems is crucial for creating a robust electric power grid and new energy industries. In this aspect, there is an urgent need to develop hybrid power systems suitable for coexistent AC and DC power grids, integrated by high-performance wide ban gap (WBG) semiconductor-based power conversion interfaces and advanced operating and control strategies. Due to the intrinsic feature of variation in RE-based power generation, the design and integration of energy storage devices, real-time regulation of power flow, and intelligent energy control schemes are key technologies for further promoting DG systems and micro-grids. This paper investigates an integrated control scheme for multiple GaN-based power converters in a small- to medium-capacity, grid-connected, and RE-based power system. This is the first time that a complete design case demonstrating three GaN-based power converters with different control functions integrated with a single digital signal processor (DSP) chip to achieve a reliable, flexible, cost effective, and multifunctional power interface for renewable power generation systems is presented. The system studied includes a photovoltaic (PV) generation unit, a battery energy storage unit, a grid-connected single-phase inverter, and a power grid. Based on system operation condition and the state of charge (SOC) of the energy storage unit, two typical operating modes and advanced power control functions are developed with a fully digital and coordinated control scheme. Hardware of the GaN-based power converters and digital controllers are designed and implemented. The feasibility and effectiveness of the designed controllers and overall performance of the proposed control scheme are verified with results from simulation and experimental tests on a 1-kVA small-scale hardware system. [ABSTRACT FROM AUTHOR]

This paper presents a live field experience of creating an isolated microgrid for the Expoelectric fair during 2018 and 2019. The islanded microgrid comprises a Master Inverter with grid-forming capabilities and fault management. The Master Inverter and stationary batteries, and EVs with V2G capabilities provide storage. A PV generation system supplies the microgrid. The loads are the fair booths, mainly lighting and chargers for personal mobility vehicles. All the equipment used in the experimental microgrid is from different manufacturers. The operation and control of the islanded microgrid are based on the VDE-AR-N-4105 standard. The paper also presents the operation of the Master Inverter during faults. The live field experience shows that the proposed operation method is valid for operating different converters from different manufacturers without needing any communication layer between them. The experimental results also show that faults can be handled correctly by the Master Inverter to operate the entire microgrid safely. In conclusion, islanded microgrids based on power electronics are feasible to replace diesel generators in faires, conventions or temporary events. [ABSTRACT FROM AUTHOR]

Grid-connected inverters in renewable energy systems must provide high-quality power to the grid according to regulatory standards such as the IEEE 1547. To provide high-quality current control when the inverter is connected to a distorted grid, the frequency and phase information of the fundamental harmonic of the grid should be accurately obtained. This paper examines controller design for a single-phase inverter when there is distortion in the grid voltage. The control structure is designed to enhance the quality of the injected current into the grid. To this end, a frequency-locked loop (FLL) sinusoidal tracking controller which is able to reject the grid harmonics is proposed. Thus, the contribution of this paper is a new frequency-locked loop structure with adaptive notch filters that can provide accurate estimation of grid phase and frequency and improve the performance of single-phase inverters working under harmonic distortion. We also present an explanation of how the proposed adaptive nonlinear scheme can be discretized for digital implementation on a microcontroller. Experimental and simulation results are presented to demonstrate the performance of the proposed controller in eliminating distortion and enhancing the quality of the produced power. [ABSTRACT FROM AUTHOR]

Green energy from Solar PV is getting increased attention in the industries due to the falling price of solar panels in the world market. A grid-tied inverter is one of the major components in such a system, where the DC energy from PV is converted to AC and synchronized with the grid to obtain power sharing between the PV and the grid for the industrial drives. In this paper, a DC link has been proposed instead of an AC link for interconnection between the solar PV system and the grid to run those industrial drives. In most modern industrial applications, induction motors are driven by VVVF (Variable Voltage and Variable Frequency) inverters to achieve efficient speed control. The inverters commonly have a rectifier section at the front end that rectifies the input AC to DC and the DC is then used in PWM mode to generate the required voltage and frequency for the induction motor operating under variable speed and load conditions. Such an inverter can use both AC or DC as the input so long the supply voltage has the right value for the inverter to operate. In our proposition, we eliminate the grid-tied inverter and use a DC link, created from the rectified AC and the regular Solar PV, to obtain the power-sharing between the PV output and the grid. Using the DC link output directly to energize the VVVF inverter has an impact on the performance of the inverter. In the proposed system, the solar PV array is designed in such a way that the grid remains as the supplementary power source only to supplement any shortfall in the PV output due to variable sunshine conditions. The control circuit used in this novel technique is inexpensive, efficient, and simple in design when compared to the grid-tied inverters. The proposed system has been implemented at Niagara Textiles in Gazipur, Bangladesh. The experimental/practical results are presented to validate the basic concept. Around a 20% reduction in the cost of energy has been reported in this paper, with a more than 90% efficient system. This will definitely make solar PV energy more competitive with regular energy and attractive to industries for its simplicity. [ABSTRACT FROM AUTHOR]

Distributed power generation plays a critical role in the stability and reliability of modern power systems. Due to the rapid growth of renewable energy generation, the requirements of the transmission and distribution system operators are becoming more stringent. Among these requirements, one of the most important is the Low-Voltage Ride-Through (LVRT) capability, which demands that the inverters remain connected to the grid and provide support during voltage sags. For this purpose, flexible current control algorithms stand out because they can manage unbalanced voltages and simultaneously achieve other control objectives. With the aim of presenting a concrete document focused on describing fundamental principles and discussing common design guidelines, this paper presents an overview of flexible current control strategies applied to LVRT capability. The operation features and design aspects of experiences reported in the literature are reviewed. Moreover, the paper proposes a general methodology to design LVRT flexible current control algorithms. Finally, current and future trends are discussed. [ABSTRACT FROM AUTHOR]

The combination of permanent magnet synchronous motor (PMSM) and inverter is the key electric drive system (EDS) of electric vehicles (EVs), and its overall efficiency seriously affects the energy consumption of EVs. In order to further improve the efficiency of PMSM-inverter, the influence of a special control object current angle β on EDS was studied and the general rule between β and EDS efficiency was obtained in this paper. Then, the golden section search (GSS) method was used to obtain optimal β and its corresponding stator current is, which can realize EDS working in optimal efficiency in the whole EDS working area. On this basis, an overall efficiency optimization control strategy for EDS based on the current angle β look-up table was proposed in this paper. To verify the effectiveness of the proposed control strategy, simulation considering iron loss and copper loss of motor and inverter loss was completed, which showed that compared with traditional control, the control strategy proposed in this paper can effectively improve the working efficiency of EDS under steady state and transient state. [ABSTRACT FROM AUTHOR]

Grid-forming inverters, which are represented by droop control and virtual synchronous generator control, have been widely studied and applied because of their excellent grid-supporting ability and smooth off-grid switching. When a grid-forming inverter is connected to a microgrid or utility grid, the control loops of active power and reactive power will be coupled because of the voltage phase difference, which will affect the power control performance. This paper first derives the small-signal linearized model of the system, based on which a frequency feedforward control and an amplitude feedforward control are proposed to decouple the active power and reactive power control loops, respectively. The proposed decoupling strategy directly modifies the reference values through feedforward with an easily implementable principle that is applicable to various control coordinate systems, control coordinate systems, and control structures. By comparing system models with and without the proposed decoupling strategy, its effectiveness can be theoretically proven. Time-domain simulations and hardware experiments are presented to further validate its effectiveness. [ABSTRACT FROM AUTHOR]

Three-level NPC inverters have been widely used in grid-connected systems due to their superior performance compared with two-level inverters, but more switches lead to high fault probability. Meanwhile, the neutral point potential (NPP) fluctuation of the DC link is an inherent problem of three-level NPC inverters. To keep the three-level NPC inverter running stably after single-arm failure, a fault-tolerant control strategy based on an optimised space vector pulse width modulation (SVPWM) is proposed in this paper. Firstly, the common-mode voltage (CMV) of the postfault three-level NPC inverter is analysed and then the preliminary synthesis principles of the reference voltage vector are determined. Then, in order to ensure the NPP balance and the quality of the grid-connected currents, the reference voltage vector synthesis rules are optimised, a low-pass filter (LPF) and a hysteresis comparator are designed, respectively, to ensure the quality of grid-connected currents and effectively decrease the DC link NPP deviation. Finally, the simulation results show that the proposed fault-tolerant control strategy can realize the stable and reliable operation of the grid-connected three-level NPC inverter after single-arm failure, and the CMV can be reduced significantly, the quality of grid-connected currents is also improved. The proposed fault-tolerant strategy also shows good performance when the grid-connected currents change. [ABSTRACT FROM AUTHOR]

The classical problem of islanding detection in distributed generation falls into the commonly used categories known as passive, active, and hybrid techniques. These approaches vary in terms of their accuracy, security, and dependability. Detecting islanding in modern inverter-based distribution systems is of the utmost importance to ensuring the protection of equipment, ensuring the safety of workers, and preventing operational and cascaded faults when the system is specially subjected to renewable integration. This research paper presents a technical comparison of the aforementioned techniques, discussing their detection rate, Non-Detection Zone (NDZ), distinct topologies, and their effectiveness in integration for low-frequency grids. The review offers a thorough analysis comparing the key attributes found in the current literature while also highlighting the forthcoming needs for advanced management, optimization, and control technologies. These technologies are crucial to effectively tackling the difficulties that arise from integrating renewable energy sources into established grid systems. [ABSTRACT FROM AUTHOR]

Changes are being implemented in the electrical power grid to accommodate the increased penetration of renewable energy sources interfaced with grid-connected inverters. The grid-forming (GFM) control paradigm of inverters in active power grids has emerged as a technique through which to tackle the effects of the diminishing dominance of synchronous generators (SGs) and is preferred to the grid-following (GFL) control for providing system control and stability in converter-dominated grids. Therefore, the development of the GFM control is important as the grid advances towards 100% inverter-based grids. In this paper, therefore, we aim to review the changing grid scenario; the behaviour of grid-connected inverter control paradigms and major GFM inverter controls, including their modifications to tackle low inertia, reduced power quality, fault-ride through capability, and reduced stability; and the state-of-the-art GFM models that are pushing the universality of GFM inverter control. [ABSTRACT FROM AUTHOR]

The inverter module serves as a critical component in the conversion of electrical energy within arc plasma power sources, exerting a profound influence on the overall performance and stability of the power supply. Consequently, the meticulous design and precise control of the inverter module are of paramount importance in ensuring the effective operation and application of arc plasma power sources. This paper introduces a dual-closed-loop control system, integrating a voltage outer loop with a current inner loop, as the cornerstone of its inverter module design. It also undertook a comprehensive comparative analysis of various voltage-control strategies, encompassing four control methods (PI, PID, PR, QPR) and two modulation techniques (bipolar modulation and unipolar, carrier-based modulation) under diverse operating conditions. Additionally, simulation experiments were conducted on a prototype 10 kW inverter module using the Matlab/Simulink simulation platform, with evaluation criteria including waveform tracking performance, voltage waveform distortion rate, and steady-state error. The results indicate that in low-frequency operating conditions, the voltage-control strategy employing QPR control plus unipolar, carrier-based modulation, and in high-frequency operating conditions, the voltage-control strategy utilizing PI control plus unipolar, carrier-based modulation exhibited superior waveform tracking performance. The waveform distortion rates were measured at below 0.47% and 4.2%, respectively, aligning perfectly with the stringent standards of IEEE 519. This research provides valuable theoretical support and practical guidance for future engineering endeavors in the field of inverters. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) energy systems have found diverse applications in fulfilling the increasing energy demand worldwide. Transformer-less PV inverters convert the DC energy from PV systems to AC energy and deliver it to the grid through a non-isolated connection. This paper proposes a new transformer-less grid-connected PV inverter. A closed-loop control scheme is presented for the proposed transformer-less inverter to connect it with the power grid. The proposed transformer-less inverter reduces extra leakage current and holds the common-mode voltage at a constant point. To eliminate extra leakage current, as well as achieve constant common-mode voltage, a midpoint clamping method is utilized to operate the inverter. The proposed transformer-less inverter is formed of seven insulated gate bipolar transistors (IGBTs) employing a unipolar sinusoidal pulse width modulation (SPWM) technique for switching purposes. An LCL filter is employed to reshape the two-level inverter output voltage and current to obtain closer sinusoidal waveforms. The output voltage and current total harmonic distortion (THD) of the proposed transformer-less inverter were found to be 1.25% and 0.94%, respectively, in the grid-connected mode. The leakage current elimination mechanism with the proposed transformer-less inverter is deeply analyzed in this paper. The performances of the proposed transformer-less inverter were evaluated with MATLAB/Simulink simulation and validated in a laboratory scale experiment. [ABSTRACT FROM AUTHOR]

In this paper, a bidirectional converter with multi-mode control strategies is proposed for a battery energy storage system (BESS). This proposed converter, which is composed of a half-bridge-type dual-active-bridge (HBDAB) converter and an H-bridge inverter, is able to operate the BESS with different power conditions and achieve the DC–AC function for lower input DC voltage applications. For the HBDAB converter, the variable-frequency control (VFC) and phase-shift control (PSC) are both adopted to achieve zero-voltage switching over a wider power range and the battery module balance control capability for BESS, respectively. In addition, the interleaved configuration is used to reduce the current ripple and increase the overall current rating. For the H-bridge inverter, the unipolar control mode (UCM) and totem-pole control mode (TPCM) are adopted to manage the real and reactive current control under different AC grid conditions. The UCM offers a reduction in current ripple for real and reactive power control. The TPCM is able to eliminate switching losses and achieve higher conversion efficiency for pure real power control. Considering applications for battery energy storage systems, the principle of operation and voltage gain analysis are described. Finally, computer simulations and hardware experimental results from a prototype system are presented to verify the performance of the proposed converter with the different control strategies. [ABSTRACT FROM AUTHOR]

In this paper, the method and a control algorithm for detecting resonant destruction of a resonant auxiliary power supply for railway vehicle are proposed. It is essential to reduce the weight of the electric equipment attached to the lower part of the railway vehicle because it greatly affects the life of the railway vehicle, such as wheel and bearing. In order to reduce the weight and volume of the auxiliary power supply, in the case of windings, high-speed switching should be performed by lowering the input voltage. Therefore, in this paper, the auxiliary power supply control algorithm using an LLC resonant converter to reduce the weight of auxiliary power supply for railway vehicle is proposed, and the method of detecting resonant destruction due to device failure of a resonant converter is proposed. The proposed algorithm steps down the wire voltage using an input buck converter for high-speed switching, and the inverter input voltage is controlled through the LLC resonant converter. In addition, ZVS (Zero Voltage Switching) is operated to minimize the loss of the resonant converter, and the optimal design of the resonant tank is also proposed. In order to detect resonant destruction, a detection method formulated by analyzing the resonant current peak value for the load capacity is proposed. The algorithm proposed in this paper is verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

In distributed generation systems, the inverter is the main power interface and its stability directly determines the reliable operation of the grid-connected system. As a typical topology for a three-phase four-wire inverter, the LCL-type three-phase four-wire split capacitor inverter (LCL-TFSCI) is taken as the research subject of this paper. Compared with the three-phase three-wire inverter, there is an additional zero-sequence path in the LCL-TFSCI. Therefore, it is not only necessary to consider the stability of the positive and negative sequence system, but there is also the need to consider the stability of the zero-sequence system when performing stability analysis for the LCL-TFSCI. In this paper, a small-signal impedance model considering the zero-sequence loop of LCL-TFSCI is firstly established. Subsequently, the instability risk is revealed when LCL-TFSCI is connected to the grid with parallel compensation capacitors. Through instability analysis, an impedance-reshaping method based on the complex filter and combined differential elements is proposed, which can reshape the impedance characteristic of LCL-TFSCI within the wide frequency range and expand the stability domain of the grid-connected system. Finally, the proposed method is verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

The discontinuous conduction mode (DCM) of the inductor current is an effective way to achieve high efficiency and high power density of inverters because it has the advantages of zero-current switching and small inductance of the filter inductor. Although the DCM can operate at a fixed switching frequency, there has been no linear model for realizing high-performance digital control. This paper provides a solution for this problem. Firstly, a linear first-order charge quantity model (CQM) for a DCM inverter with a fixed switching frequency is established, which uses charge quantities output by the inverter bridge as a control variable. Secondly, a direct charge control (DCC) method is proposed, and the design process is significantly simplified. Finally, the performance of the proposed control method is verified by the experiments using a 1 kW prototype, and a high-quality output voltage waveform with a peak efficiency of above 98% was achieved. The proposed method outperforms existing works because the CQM is a first-order linear model that realizes the high-performance digital control and significantly simplifies the design of controller. [ABSTRACT FROM AUTHOR]