Search

5-hydroxymethylfurfural (HMF) is oxidized to 2,5-furandicarboxylic acid (FDCA), which serves as a sustainable alternative to the petrochemical derivative terephthalic acid as a polyester monomer. Currently, noble metal catalysts that combine high HMF conversion rates with FDCA selectivity have become one of the mainstream catalytic systems for HMF oxidation. This paper summarizes and discusses the research progress on HMF oxidation to FDCA over different noble metal-based catalysts by combining DFT theoretical calculations, introducing various reaction pathways and mechanisms of HMF oxidation. It also analyzes the characteristics and electronic properties of metal active sites, geometric effects, metal–support interactions, and confinement effects, discussing and revealing the roles and activation mechanisms of different metal active sites, the structure of catalysts, active substances, metal valence states, activity, and the relationship between metal and the oxidation of C=O and OH groups. Finally, it presents views on the challenges and future development in the design of noble metal-based catalysts. [ABSTRACT FROM AUTHOR]

Upgrading the bio-derived platform chemical 5-hydroxymethylfurfural (HMF) into the high value-added bioplastic monomer 2,5-furandicarboxylic acid (FDCA) is a promising pathway for biomass conversion. In this work, the natural and abundant available mineral vermiculite was employed as a carrier for loading a Au-Pd bimetal catalyst. Due to the high dispersion of bimetallic nanoparticles, this synthesized vermiculite-supported Au-Pd bimetal catalyst revealed excellent catalytic performance for the aerobic oxidation of HMF to FDCA. By adjusting the ratio of Au and Pd metals, the catalytic performance of the catalyst can be optimized. Finally, 100% HMF conversion and 99.9% FDCA yield could be obtained under the conditions of Au/Pd = 2/1, 2 h, 2 MPa O2, and 100 °C. The catalyst revealed good stability, and the FDCA yield can be maintained at 90.1% after five recycle usages. The physicochemical properties of the synthesized catalysts were characterized by various characterization methods. It could be concluded that the high dispersion and alloying effect of bimetallic nanoparticles promoted the activation of reactants and intermediates, resulting in the effective production of FDCA. This study could provide ideas and references for the development and utilization of natural minerals and also offer a new way to realize the efficient conversion of HMF to FDCA under green conditions. [ABSTRACT FROM AUTHOR]

Furanoate polyesters are an extremely promising new class of materials for packaging applications, particularly furanoate-based nanocomposites, which have gained a high interest level in research and development in both academia and industries. The monomers utilised for the synthesis of furanoate-based polyesters were derived from lignocellulosic biomass, which is essential for both eco-friendliness and sustainability. Also, these polyesters have a lower carbon footprint compared to fossil-based plastics, contributing to greenhouse gas reduction. The furanoate-based nanocomposites exhibit enhanced performance characteristics, such as high thermal stability, excellent mechanical strength, superior barrier resistance, and good bacteriostatic rate, making them suitable for a wide range of industrial applications, especially for food-packaging applications. This paper reviews the recent trends in the synthesis routes of monomers, such as the various catalytic activities involved in the oxidation of 5(hydroxymethyl)furfural (HMF) into 2,5-furandicarboxylic acid (FDCA) and its ester, dimethyl furan-2,5-dicarboxylate (DMFD). In addition, this review explores the fabrication of different furanoate-based nanocomposites prepared by in situ polymerization, by melt mixing or solvent evaporation methods, and by using different types of nanoparticles to enhance the overall material properties of the resulting nanocomposites. Emphasis was given to presenting the effect of these nanoparticles on the furanoate polyester's properties. [ABSTRACT FROM AUTHOR]

Cutin, one of the main structural components of tomato peels, is a waxy biopolymer rich in hydroxylated fatty acids. In this study, 10,16-dihydroxyhexadecanoic acid (10,16-diHHDA) was extracted and isolated from tomato peels and exploited to develop fully crosslinked polyesters as potential candidates for replacing fossil-based metal protective coatings. A preliminary screening was conducted to select the base formulation, and then a design of experiments (DoE) was used as a methodology to identify the optimal composition to develop a suitable coating material. Different formulations containing 10,16-diHHDA and other biorefinery monomers, including 2,5-furandicarboxylic acid, were considered. To this end, all polyesters were characterized through differential scanning calorimetry (DSC) and gel content measurements to determine their Tg value and crosslinking efficiency. Compositions exhibiting the best trade-off between Tg value, chemical resistance, and sufficiently high 10,16-diHHDA content between 39 and 48 wt.% were used to prepare model coatings that were characterized for assessing their wettability, scratch hardness, chemical resistance, and adhesion to metal substrates. These polyester coatings showed a Tg in the range of 45–55 °C, a hydrophobic behavior with a water contact angle of around 100°, a good solvent resistance (>100 MEK double rubs), and an adhesion strength to steel higher than 2 MPa. The results obtained confirmed the potential of cutin-based resins as coatings for metal protection, meeting the requirements for ensuring physicochemical properties of the final product, as well as for optimizing the valorization of such an abundant agri-food waste as tomato peels. [ABSTRACT FROM AUTHOR]

The electrocatalytic conversion of biomass into high-value-added chemicals is one of the effective methods of green chemistry. Conventional metal catalysts have disadvantages, such as low atomic utilization and small surface areas. Catalyst materials derived from metal–organic frameworks (MOFs) have received much attention due to their unique physicochemical properties. Here, an MOF-derived non-precious metal CoxNiyS electrocatalyst was applied to the oxidation of biomass-derivative 5-hydroxymethylfurfural (HMF). The HMF oxidation reaction activities were modulated by regulating the content of Co and Ni bimetals, showing a volcano curve with an increasing proportion of Co. When the Co:Ni ratio was 2:1, the HMF conversion rate reached 84.5%, and the yield of the main product, 2,5-furandicarboxylic acid (FDCA), was 54%. The XPS results showed that the presence of high-valent nickel species after electrolysis, which further proved the existence and reactivity of NiOOH, as well as the synergistic effect of Co and Ni promoted the conversion of HMF. Increasing the content of Ni could increase the activity of HMF electrochemical oxidation, and increasing the content of Co could reduce the increase in the anodic current. This study has important significance for designing better HMF electrochemical catalysts in the future. [ABSTRACT FROM AUTHOR]

High molecular weight, fully biobased random copolymers of 2,5-furandicarboxylic acid (2,5-FDCA) containing different amounts of (1R, 3S)-(+)-Camphoric Acid (CA) have been successfully synthesized by two-stage melt polycondensation and compression molding in the form of films. The synthesized copolyesters have been first subjected to molecular characterization by nuclear magnetic resonance spectroscopy and gel-permeation chromatography. Afterward, the samples have been characterized from a thermal and structural point of view by means of differential scanning calorimetry, thermogravimetric analysis, and wide-angle X-ray scattering, respectively. Mechanical and barrier properties to oxygen and carbon dioxide were also tested. The results obtained revealed that chemical modification permitted a modulation of the abovementioned properties depending on the amount of camphoric co-units present in the copolymers. The outstanding functional properties promoted by camphor moieties addition could be associated with improved interchain interactions (π-π ring stacking and hydrogen bonds). [ABSTRACT FROM AUTHOR]

Aerobic oxidation of bio-sourced 2,5-bis(hydroxymethyl)furan (BHMF) to 2, 5-furandicarboxylic acid (FDCA), a renewable and green alternative to petroleum-derived terephthalic acid (TPA), is of great significance in green chemicals production. Herein, hierarchical porous bowl-like nitrogen-rich (nitrated) carbon-supported bimetallic Au-Pd nanocatalysts (AumPdn/ N-BNxC) with different nitrogen content and bimetal nanoparticle sizes were developed and employed for the highly efficient aerobic oxidation of BHMF to FDCA in sodium carbonate aqueous solution. The reaction pathway for catalytic oxidation of BHMF went through the steps of BHMF→HMF→HMFCA→FFCA→FDCA. Kinetics studies showed that the activation energies of BHMF, HMF, HMFCA, and FFCA were 58.1 kJ·moL−1, 39.1 kJ·moL−1, 129.2 kJ·moL−1, and 56.3 kJ·moL−1, respectively, indicating that the oxidation of intermediate HMFCA to FFCA was the rate-determining step. ESR tests proved that the active species was a superoxide radical. Owing to the synergy between the nitrogen-rich carbon support and bimetallic Au-Pd nanoparticles, the Au1Pd1/N-BN2C nanocatalysts exhibited BHMF conversion of 100% and FDCA yield of 95.8% under optimal reaction conditions. Furthermore, the nanocatalysts showed good stability and reusability. This work provides a versatile strategy for the design of heterogeneous catalysts for the highly efficient production of FDCA from BHMF. [ABSTRACT FROM AUTHOR]

The solubility of 2,5-furandicarboxylic acid (FDCA) and its synthetic intermediates (e.g., 5-formylfuran-2-carboxylic acid, FFCA) provides fundamental information for the preparation and purification of the value-added biocompound FDCA. We measured the solubility of FDCA and FFCA in binary water + 1,4-dioxane mixtures with different mixing ratios at 303.15 K–342.15 K. The obtained solubility values were correlated with the Jouyban-Acree-van't Hoff model, and the preferential solvation theory was used to study the microscopic dissolution mechanism. The solubility of FDCA/FFCA increases with increasing temperature, and pure 1,4-dioxane dissolves more solutes than pure water. FFCA shows higher solubility than FDCA. In the binary solvent mixtures, the phenomenon of co-solvency exists for both FDCA and FFCA, i.e., at a 1,4-dioxane mole fraction of about 0.60, FDCA and FFCA dissolve the most. Acceptable mean percentage deviations (MPD) (5.5% and 6.9%) are obtained for FDCA and FFCA (Jouyban-Acree-van't Hoff model). The calculated preferential solvation parameters show different dissolution mechanisms at different solvent compositions. When the 1,4-dioxane mole fraction is 0.17~0.62/0.63, FDCA/FFCA are preferentially solvated by 1,4-dioxane. Otherwise, they are preferentially solvated by water. A trend similar to the "co-solvency phenomenon" is observed in the differences in solubility of FFCA and FDCA. This study gives important guidance for the use of binary water and 1,4-dioxane solvents in practical FDCA purification. [ABSTRACT FROM AUTHOR]

This work explores for the first time the use of a fed-batch and continuous packed-bed millibioreactor for the chemoenzymatic oxidation of 2,5-furandicarboxaldehyde (DFF) to 2,5-furandicarboxylic acid (FDCA). Different operational variables were studied: temperature, substrate concentration, and flow rate using different reactors (batch, fed-batch, and a continuous packed-bed bioreactor). The best yield (100%) was achieved using the fed-batch reactor at an H2O2 flow rate of 3 µL/min with a substrate concentration (DFF) of 100 mM. Regarding the specific productivity, the highest values (>0.05 mg product/min g biocatalyst) were reached with the operation in the fed-batch bioreactor and the continuous packed-bed bioreactor. The yield of the biocatalyst decreased by 98% after the first reaction cycle during the operational stability tests, due to a substantial inactivation of the biocatalyst by H2O2 and peracid. In this study, it is possible to select the operational variables in fed-batch and continuous reactors for chemoenzymatic oxidation that can increase the yield and specific productivity; however, the stability of the biocatalyst should be improved in future research. [ABSTRACT FROM AUTHOR]

Poly(2,5-furandicarboxylate)s incorporating aliphatic moieties represent a promising family of polyesters, typically entirely based on renewable resources and with tailored properties, notably degradability. This study aims to go beyond by developing poly(isosorbide 2,5-furandicarboxylate-co-dodecanedioate) copolyesters derived from isosorbide (Is), 2,5-furandicarboxylic acid (FDCA), and 1,12-dodecanedioic acid (DDA), and studying their degradation under environmental conditions, often overlooked, namely seawater conditions. These novel polyesters have been characterized in-depth using ATR-FTIR, 1H, and 13C NMR and XRD spectroscopies and thermal analysis (TGA and DSC). They showed enhanced thermal stability (up to 330 °C), and the glass transition temperature increased with the content of FDCA from ca. 9 to 60 °C. Regarding their (bio)degradation, the enzymatic conditions lead to the highest weight loss compared to simulated seawater conditions, with values matching 27% vs. 3% weight loss after 63 days of incubation, respectively. Copolymerization of biobased FDCA, Is, and DDA represents an optimal approach for shaping the thermal/(bio)degradation behaviors of these novel polyesters. [ABSTRACT FROM AUTHOR]

The classic acrylonitrile (AN) electrohydrodimerization (EHD) to adiponitrile (ADN) process produces oxygen on the anode side. The oxygen evolution reaction (OER) is energy consuming, and O2 is of low value and has security issues while directly contacting with organic molecules. Herein, by replacing OER with 5-hydroxymethylfurfural oxidation reaction (HMFOR), we report paired electrolysis of AN and HMF for simultaneous generation of ADN and 2,5-furandicarboxylic acid (FDCA). On the anode side, the electrodeposited amorphous NiMoP film-covered nickel foam efficiently boosted HMFOR activity by enlarging the electrochemically active surface area (ECSA) via in situ selective removal of Mo and P on the surface. On the cathode side, addition of dimethylformamide (DMF) as a cosolvent enhanced the reaction efficiency of ANEHD by forming a single-phase electrolyte that offers better interaction between AN and the electrode. The ANEHD–HMFOR paired system shows excellent generation rates of FDCA (0.018 gFDCA·h−1·cm−2) and ADN (0.017 gADN·h−1·cm−2) at a high cell current (160 mA). An amount of 1 kWh of electricity can produce 2.91 mol of ADN and 0.53 mol of FDCA with 107.1% Faraday efficiency. [ABSTRACT FROM AUTHOR]

A series of poly(ester amide)s based on dimethyl furan 2,5-dicarboxylate (DMFDC), 1,3-propanediol (PDO), 1,6-hexylene glycol (HDO), and 1,3-diaminopropane (DAP) were synthesized via two-step melt polycondensation. The phase transition temperatures and structure of the polymers were studied by differential scanning calorimetry (DSC). The positron annihilation lifetime spectroscopy (PALS) measurement was carried out to investigate the free volume. In addition, the mechanical properties of two series of poly(ester amide)s were analyzed. The increase in the number of methylene groups in the polymer backbone resulted in a decrease in the values of the transition temperatures. Depending on the number of methylene groups and the content of the poly(propylene furanamide) (PPAF), both semi-crystalline and amorphous copolymers were obtained. The free volume value increased with a greater number of methylene groups in the polymer backbone. Moreover, with a lower number of methylene groups, the value of the Young modulus and stress at break increased. [ABSTRACT FROM AUTHOR]

In the last decade, there has been an increased interest from the food packaging industry toward the development and application of bioplastics, to contribute to the sustainable economy and to reduce the huge environmental problem afflicting the planet. In the present work, we focus on a new furan-based polyester, poly(neopentyl glycol 2,5-furanoate) (PNF) to be used for sustainable food packaging applications. The aromatic polyester was successfully synthesized with high molecular weight, through a solvent-free process, starting directly from 2,5-furandicarboxylic acid. PNF was revealed to be a material with good thermal stability, characterized by a higher Tg and Tm and a lower RAF fraction compared to poly(propylene 2,5-furanoate) (PPF), ascribable to the two methyl side groups present in PNF glycol-sub-unit. PNF's mechanical characteristics, i.e., very high elastic modulus and brittle fracture, were found to be similar to those of PPF and PEF. Barrier properties to different gases, temperatures and relative humidity were evaluated. From the results obtained, PNF was showed to be a material with very smart barrier performances, significantly superior with respect to PEF's ones. Lastly, PNF's permeability behavior did not appreciably change after contact with food simulants, whereas it got worse with increasing RH, due to the polar nature of furan ring. [ABSTRACT FROM AUTHOR]

Converting biomass into high value-added compounds has attracted great attention for solving fossil fuel consumption and global warming. 5-Hydroxymethylfurfural (HMF) has been considered as a versatile biomass-derived building block that can be used to synthesize a variety of sustainable fuels and chemicals. Among these derivatives, 2,5-furandicarboxylic acid (FDCA) is a desirable alternative to petroleum-derived terephthalic acid for the synthesis of biodegradable polyesters. Herein, to fully understand the current development of the catalytic conversion of biomass to FDCA, a comprehensive review of the catalytic conversion of cellulose biomass to HMF and the oxidation of HMF to FDCA is presented. Moreover, future research directions and general trends of using biomass for FDCA production are also proposed. [ABSTRACT FROM AUTHOR]

This study demonstrates the use of a photoelectrochemical device comprising earth-abundant hematite photoanode for the oxidation of 5-hydroxymethylfurfural (5-HMF), a versatile bio-based platform chemical, under ambient conditions in the presence of an electron mediator. The results obtained in this study showed that the hematite photoanode, upon doping with fluorine, can oxidize water even at lower pH (4.5 and 9.0). For 5-HMF oxidation, three different pH conditions were investigated, and complete oxidation to 2,5-furandicarboxylic acid (FDCA) via 5-hydroxymethyl-2-furancarboxylic acid (HMFCA) was achieved at pH above 12. At lower pH, the oxidation followed another route via 2,5-diformylfuran (DFF), yielding 5-formyl-2-furancarboxylic acid (FFCA) as the main product. Using the oxidized intermediates as substrates showed DFF to be most efficiently oxidized to FDCA. We also show that, at pH 4.5, the addition of the laccase enzyme promoted the oxidation of 5-HMF to FFCA. [ABSTRACT FROM AUTHOR]

Oxidation of 5-hydroxymethylfurfural (HMF), a major feedstock derived from waste/fresh biomass, into 2,5-furandicarboxylic acid (FDCA) is an important transformation for the production of biodegradable plastics. Herein, we investigated the effect of the support (unmodified and modified titania, commercial alumina, and untreated and treated Sibunit carbon) of mono- and bimetallic catalysts based on noble metals (Ag, Au, Pd) on selective HMF oxidation with molecular oxygen to FDCA under mild and basic reaction conditions. The higher selectivity to FDCA was obtained when metals were supported on Sibunit carbon (Cp). The order of noble metal in terms of catalyst selectivity was: Ag < Au < Pd < PdAu. Finally, FDCA production on the most efficient PdAu NPs catalysts supported on Sibunit depended on the treatment applied to this carbon support in the order: PdAu/Cp < PdAu/Cp-HNO3 < PdAu/Cp-NH4OH. These bimetallic catalysts were characterized by nitrogen adsorption-desorption, inductively coupled plasma atomic emission spectroscopy, high resolution transmission electron microscopy, energy dispersive spectroscopy, X-ray diffraction, Hammet indicator method and X-ray photoelectron spectroscopy. The functionalization of Sibunit surface by HNO3 and NH4OH led to a change in the contribution of the active states of Pd and Au due to promotion effect of N-doping and, as a consequence, to higher FDCA production. HMF oxidation catalyzed by bimetallic catalysts is a structure sensitive reaction. [ABSTRACT FROM AUTHOR]

Poly(2,5-alkylene furanoate)s are bio-based, smart, and innovative polymers that are considered the most promising materials to replace oil-based plastics. These polymers can be synthesized using ecofriendly approaches, starting from renewable sources, and result into final products with properties comparable and even better than those presented by their terephthalic counterparts. In this work, we present the molecular dynamics of four 100% bio-based poly(alkylene 2,5-furanoate)s, using broadband dielectric spectroscopy measurements that covered a wide temperature and frequency range. We unveiled complex local relaxations, characterized by the simultaneous presence of two components, which were dependent on thermal treatment. The segmental relaxation showed relaxation times and strengths depending on the glycolic subunit length, which were furthermore confirmed by high-frequency experiments in the molten region of the polymers. Our results allowed determining structure–property relations that are able to provide further understanding about the excellent barrier properties of poly(alkylene 2,5-furanoate)s. In addition, we provide results of high industrial interest during polymer processing for possible industrial applications of poly(alkylene furanoate)s. [ABSTRACT FROM AUTHOR]

For the production of chemicals from biomass, new selective processes are required. The selective oxidation of 5-(Hydroxymethyl)furfural (HMF), a promising platform molecule in fine chemistry, to 2,5-furandicarboxylic acid (FDCA) is considered a promising approach and requires the oxidation of two functional groups. In this study, Au/ZrO2 catalysts with different mean particle sizes were prepared by a chemical reduction method using tetrakis(hydroxymethyl)phosphonium chloride (THPC) and tested in HMF oxidation. The catalyst with the smallest mean particle size (2.1 nm) and the narrowest particle size distribution was highly active in the oxidation of the aldehyde moiety of HMF, but less active in alcohol oxidation. On the other hand, increased activity in FDCA synthesis up to 92% yield was observed over catalysts with a larger mean particle size (2.7 nm), which had a large fraction of small and some larger particles. A decreasing FDCA yield over the catalyst with the largest mean particle size (2.9 nm) indicates that the oxidation of both functional groups require different particle sizes and hint at the presence of an optimal particle size for both oxidation steps. The activity of Au particles seems to be influenced by surface steps and H bonding strength, the latter particularly in aldehyde oxidation. Therefore, the presence of both small and some larger Au particles seem to give catalysts with the highest catalytic activity. [ABSTRACT FROM AUTHOR]

Intending to expand the thermo-physical properties of bio-based polymers, furan-based thermoplastic polyesters were synthesized following the melt polycondensation method. The resulting polymers, namely, poly(ethylene 2,5-furandicarboxylate) (PEF), poly(propylene 2,5-furandicarboxylate) (PPF), poly(butylene 2,5-furandicarboxylate) (PBF) and poly(1,4-cyclohexanedimethylene 2,5-furandicarboxylate) (PCHDMF) are used in blends together with various polymers of industrial importance, including poly(ethylene terephthalate) (PET), poly(ethylene 2,6-naphthalate) (PEN), poly(L-lactic acid) (PLA) and polycarbonate (PC). The blends are studied concerning their miscibility, crystallization and solid-state characteristics by using wide-angle X-ray diffractometry (WAXD), differential scanning calorimetry (DSC) and polarized light microscopy (PLM). PEF blends show in general dual glass transitions in the DSC heating traces for the melt quenched samples. Only PPF–PEF blends show a single glass transition and a single melt phase in PLM. PPF forms immiscible blends except with PEF and PBF. PBF forms miscible blends with PCHDMF and PPF, whereas all other blends show dual glass transitions in DSC and phase separation in PLM. PCHDMF–PEF and PEN–PEF blends show two glass transition temperatures, but they shift to intermediate temperature values depending on the composition, indicating some partial miscibility of the polymer pairs. [ABSTRACT FROM AUTHOR]

Using 2,5-furandicarboxylic acid, ethylene glycol, and poly(ethylene glycol) as raw materials and ethylene glycol antimony as a catalyst, poly(ethylene furandicarboxylate) (PEF) and polyethylene glycol (PEG) copolymers (PEGFs) were synthesized by transesterification by changing the molecular weight of PEG (from 600 to 10,000 g/mol) and the PEG content (from 10 to 60 wt %). The thermal, hydrophilic, degradation, and spinnility characteristics of these copolymers were then investigated. Thermogravimetric analysis shows that PEGF is thermally stable at 62 °C, much lower than the temperature for PEF. The intrinsic viscosity of the obtained copolyester was between 0.67 and 0.99 dL/g, which is higher than the viscosity value of PEF. The contact angle experiment shows that the hydrophilicity of PEGFs is improved (the surface contact angle is reduced from 91.9 to 63.3°), which gives PEGFs a certain degradability, and the maximum mass loss can reach approximately 15%. Melt spinning experiments show that the PEGF polymer has poor spinnability, but the mechanical properties of the polymer monofilament are better. [ABSTRACT FROM AUTHOR]

The worldwide regulatory demand for the elimination of non-phthalate compounds for poly(vinyl chloride) (PVC) plasticization has intensified the search for alternatives. Concomitantly, sustainability concerns have highlighted sugar-based 2,5-furandicarboxylic acid as one key renewable-chemical for the development of several products, namely di(2-ethylhexyl) 2,5-furandicarboxylate (DEHF) plasticizer. This study addresses the use of DEHF under a realistic scenario of the co-existence of both DEHF and entirely fossil-based plasticizers. More precisely, original PVC blends using mixtures of non-toxic DEHF and di(2-ethylhexyl) terephthalate ester (DEHT) were designed. The detailed structural, thermal, and mechanical characterization of these materials showed that they all have a set of interesting properties that are compatible with those of commercial DEHT, namely a low glass transition (19.2–23.8 °C) and enhanced elongation at break (up to 330%). Importantly, migration tests under different daily situations, such as for example exudation from food/beverages packages and medical blood bags, reveal very low weight loss percentages. For example, in both distilled water and phosphate buffered saline (PBS) solution, weight loss does not exceed ca. 0.3% and 0.2%, respectively. Viability tests show, for the first time, that up to 500 μM of DEHF, a promising cytotoxic profile is observed, as well as for DEHT. Overall, this study demonstrates that the combination of DEHF and DEHT plasticizers result in a noticeable plasticized PVC with an increased green content with promising cytotoxic results. [ABSTRACT FROM AUTHOR]

Recently, we have developed an eco-friendly method for the preparation of a renewable dicarboxylic acid 2,5-furandicarboxylic acid (FDCA) from biomass-based 5-hydroxymethylfrufural (HMF). In the present work, we optimized our reported method, which used phosphate buffer and Fe(OH)3 as the stabilizer to improve the stability of potassium ferrate, then got a purified FDCA (up to 99%) in high yield (91.7 wt %) under mild conditions (25 °C, 15 min, air atmosphere). Subsequently, the obtained FDCA, along with 1,6-hexanediol (HDO), which was also made from HMF, were used as monomers for the synthesis of poly(hexylene 2,5-furandicarboxylate) (PHF) via direct esterification, and triphenyl phosphite was used as the antioxidant to alleviate the discoloration problem during the esterification. The intrinsic viscosity, mechanical properties, molecular structure, thermal properties, and degradability of the PHFs were measured or characterized by Koehler viscometer, universal tensile tester, Nuclear Magnetic Resonance (NMR), Fourier-transform Infrared (FTIR), X-ray diffraction (XRD), Differential Scanning Calorimeter (DSC), Derivative Thermogravimetry (DTG), Scanning Electron Microscope (SEM), and weight loss method. The experimental evidence clearly showed that the furan-aromatic polyesters prepared from biomass-based HMF are viable alternatives to the petrochemical benzene-aromatic polyesters, they can serve as low-melting heat bondable fiber, high gas-barrier packaging material, as well as specialty material for engineering applications. [ABSTRACT FROM AUTHOR]

Poly(ether ester)s (PEEs) represent a promising class of segmented co-polymers, nevertheless the synthesis of PEEs based on renewable 2,5-furandicarboxylic acid (FDCA) is still scarce. In this context, a series of poly(1,4-butylene 2,5-furandicarboxylate)-co-poly(poly(propylene oxide) 2,5-furandicarboxylate) co-polyesters with different composition of stiff poly(1,4-butylene 2,5-furandicarboxylate) (PBF) and soft poly(poly(propylene oxide) 2,5-furandicarboxylate) (PPOF) moieties were synthesized, via a two-step bulk polytransesterification reaction. The molar ratio of PBF/PPOF incorporated was varied (10 to 50 mol%) in order to prepare several novel materials with tuned properties. The materials were characterised in detail through several techniques, namely ATR FTIR, 1H and 13C NMR, TGA, DSC, DMTA and XRD. Their hydrolytic and enzymatic degradation evaluation was also assessed. These new co-polymers showed either a semi-crystalline nature when higher PBF/PPOF ratios were used, and for approximately equal amounts of PBF and PPOF an amorphous co-polyester was obtained instead. [ABSTRACT FROM AUTHOR]

Polyesters made from 2,5-furandicarboxylic acid (FDCA) have been in the spotlight due to their renewable origins, together with the promising thermal, mechanical, and/or barrier properties. Following the same trend, (nano)composite materials based on FDCA could also generate similar interest, especially because novel materials with enhanced or refined properties could be obtained. This paper presents a case study on the use of furanoate-based polyesters and bacterial cellulose to prepare nanocomposites, namely acetylated bacterial cellulose/poly(butylene 2,5-furandicarboxylate) and acetylated bacterial cellulose/poly(butylene 2,5-furandicarboxylate)-co-(butylene diglycolate)s. The balance between flexibility, prompted by the furanoate-diglycolate polymeric matrix; and the high strength prompted by the bacterial cellulose fibres, enabled the preparation of a wide range of new nanocomposite materials. The new nanocomposites had a glass transition between −25–46 °C and a melting temperature of 61–174 °C; and they were thermally stable up to 239–324 °C. Furthermore, these materials were highly reinforced materials with an enhanced Young's modulus (up to 1239 MPa) compared to their neat copolyester counterparts. This was associated with both the reinforcing action of the cellulose fibres and the degree of crystallinity of the nanocomposites. In terms of elongation at break, the nanocomposites prepared from copolyesters with higher amounts of diglycolate moieties displayed higher elongations due to the soft nature of these segments. [ABSTRACT FROM AUTHOR]

Two series of aliphatic-aromatic copolyesters derived from succinic and 2,5-furandicarboxylic acids, and di- O -2-(hydroxyethyl) resorcinol as diol substituent of either 1,4-butanediol or ethylene glycol, respectively, were obtained by ring opening polymerization(ROP) performed in bulk and catalyzed by Sn(Oct)₂. Cyclic oligomers of furandicarboxylate of di- O -2-(hydroxyethyl) resorcinol were successfully synthesized by high-dilution condensation, and then copolymerized with cyclic oligomers of either butylene or ethylene succinate. The synthesized resorcinol-containing succinate-furanoatecopolyesters had M w oscillating between 50,000 and 30,000 g·mol -1 depending on composition, and they all displayed a nearly random microstructure. They showed an excellent thermal stability with onset decomposition temperatures near 300 °C. They are amorphous with T g increasing monotonically with the content in resorcinol in both series with values ranging from -30 or -13 °C for butylene and ethylene-based copolyesters, respectively, up to around 45 °C. The resorcinol-containing succinate-furanoate copolyesters showed appreciable hydrolytic degradation when incubated for a few weeks in water under physiological conditions, a behavior that was notably enhanced in the presence of lipases., Competing Interests: The authors declare no conflict of interest.