Search

Frontal plane ankle motion is important for balance in walking but is seldom controlled in robotic prostheses. This article describes the design, control and performance of a semi-active two-degree-of-freedom robotic prosthetic ankle. The mechanism uses a non-backdrivable wedge cam system based on rotating inclined planes, allowing actuation only during swing phases for low power, light weight and compactness. We present details of the mechanism and its kinematic and mechatronic control, and a benchtop investigation of the system's speed and accuracy in ankle angle control. The two-axis ankle achieves angular reorientation movements spanning ±10 deg in any direction in less than 0.9 s. It achieves a plantarflexion/dorsiflexion error of 0.35 ± 0.27 deg and an inversion/eversion error of 0.29 ± 0.25 deg. Backdriven motion during walking tests is negligible. Strengths of the design include self-locking behavior for low power and simple kinematic control. Two-axis ankle angle control could enable applications such as balance augmentation, turning assistance, and wearable perturbation training. [ABSTRACT FROM AUTHOR]

Motion reconstruction using wearable sensors enables broad opportunities for gait analysis outside laboratory environments. Inertial Measurement Unit (IMU)-based foot trajectory reconstruction is an essential component of estimating the foot motion and user position required for any related biomechanics metrics. However, limitations remain in the reconstruction quality due to well-known sensor noise and drift issues, and in some cases, limited sensor bandwidth and range. In this work, to reduce drift in the height direction and handle the impulsive velocity error at heel strike, we enhanced the integration reconstruction with a novel kinematic model that partitions integration velocity errors into estimates of acceleration bias and heel strike vertical velocity error. Using this model, we achieve reduced height drift in reconstruction and simultaneously accomplish reliable terrain determination among level ground, ramps, and stairs. The reconstruction performance of the proposed method is compared against the widely used Error State Kalman Filter-based Pedestrian Dead Reckoning and integration-based foot-IMU motion reconstruction method with 15 trials from six subjects, including one prosthesis user. The mean height errors per stride are 0.03 ± 0.08   c m on level ground, 0.95 ± 0.37   c m on ramps, and 1.27 ± 1.22   c m on stairs. The proposed method can determine the terrain types accurately by thresholding on the model output and demonstrates great reconstruction improvement in level-ground walking and moderate improvement on ramps and stairs. [ABSTRACT FROM AUTHOR]

The labor-intensive nature of the construction industry requires workers to frequently perform physically demanding manual work, thereby exposing them to the risk of musculoskeletal injury (approximately 31.2 cases per 10,000 full-time equivalent workers). Exoskeletons and exosuits (collectively called EXOs here) are designed to protect workers from these injuries by reducing exertion and muscle fatigue during work. However, the usability of EXOs in construction is still not clear. This is because extant EXO assessments in construction were mainly conducted in laboratory environments with test participants who are not construction professionals. In this research, we conducted a pilot study to investigate the usability of EXOs in a real construction workplace. Four experienced workers were recruited to push/empty construction gondolas with and without a Back-Support EXO, HeroWear Apex. Three workers were recruited to install/remove wooden blocks between steel studs with and without two Arm-Support EXOs, i.e., Ekso EVO and Hilti EXO-001. Their motions, postures, heart rates, and task completion times were recorded and compared. The workers were also surveyed to gather their attitudes toward the EXO's usefulness and ease of use. The study results demonstrated that the workers responded to the use of EXOs differently and consequently were not unanimously in favor of EXO adoption in practice. The preliminary results and findings from this pilot study help in building a foundation of understanding to improve EXO products to fit the needs of construction workers and foster EXO-enabled construction tasks in the future. [ABSTRACT FROM AUTHOR]

Exoskeletons and exosuits (collectively termed EXOs) have the potential to reduce the risk of work-related musculoskeletal disorders (WMSDs) by protecting workers from exertion and muscle fatigue due to physically demanding, repetitive, and prolonged work in construction workplaces. However, the use of EXOs in construction is in its infancy, and much of the knowledge required to drive the acceptance, adoption, and application of this technology is still lacking. The objective of this research is to identify the facilitators, barriers, and corresponding solutions to foster the adoption of EXOs in construction workplaces through a sequential, multistage Delphi approach. Eighteen experts from academia, industry, and government gathered in a workshop to provide insights and exchange opinions regarding facilitators, barriers, and potential solutions from a holistic perspective with respect to business, technology, organization, policy/regulation, ergonomics/safety, and end users (construction-trade professionals). Consensus was reached regarding all these perspectives, including top barriers and potential solution strategies. The outcomes of this study will help the community gain a comprehensive understanding of the potential for EXO use in the construction industry, which may enable the development of a viable roadmap for the evolution of EXO technology and the future of EXO-enabled workers and work in construction workplaces. [ABSTRACT FROM AUTHOR]

Muscle–tendon power output is commonly assessed in the laboratory through the work loop, a paired analysis of muscle force and length during a cyclic task. Work-loop analysis of muscle–tendon function in out-of-lab conditions has been elusive due to methodological limitations. In this work, we combined kinetic and kinematic measures from shear wave tensiometry and inertial measurement units, respectively, to establish a wearable system for estimating work and power output from the soleus and gastrocnemius muscles during outdoor locomotion. Across 11 healthy young adults, we amassed 4777 strides of walking on slopes from −10° to +10°. Results showed that soleus work scales with incline, while gastrocnemius work is relatively insensitive to incline. These findings agree with previous results from laboratory-based studies while expanding technological capabilities by enabling wearable analysis of muscle–tendon kinetics. Applying this system in additional settings and activities could improve biomechanical knowledge and evaluation of protocols in scenarios such as rehabilitation, device design, athletics, and military training. [ABSTRACT FROM AUTHOR]

(1) Background: Semi-active prosthetic feet can provide adaptation in different circumstances, enabling greater function with less weight and complexity than fully powered prostheses. However, determining how to control semi-active devices is still a challenge. The dynamic mean ankle moment arm (DMAMA) provides a suitable biomechanical metric, as its simplicity matches that of a semi-active device. However, it is unknown how stiffness and locomotion modes affect DMAMA, which is necessary to create closed-loop controllers for semi-active devices. In this work, we develop a method to use only a prosthesis-embedded load sensor to measure DMAMA and classify locomotion modes, with the goal of achieving mode-dependent, closed-loop control of DMAMA using a variable-stiffness prosthesis. We study how stiffness and ground incline affect the DMAMA, and we establish the feasibility of classifying locomotion modes based exclusively on the load sensor. (2) Methods: Human subjects walked on level ground, ramps, and stairs while wearing a variable-stiffness prosthesis in low-, medium-, and high-stiffness settings. We computed DMAMA from sagittal load sensor data and prosthesis geometric measurements. We used linear mixed-effects models to determine subject-independent and subject-dependent sensitivity of DMAMA to incline and stiffness. We also used a machine learning model to classify locomotion modes using only the load sensor. (3) Results: We found a positive linear sensitivity of DMAMA to stiffness on ramps and level ground. Additionally, we found a positive linear sensitivity of DMAMA to ground slope in the low- and medium-stiffness conditions and a negative interaction effect between slope and stiffness. Considerable variability suggests that applications of DMAMA as a control input should look at the running average over several strides. To examine the efficacy of real-time DMAMA-based control systems, we used a machine learning model to classify locomotion modes using only the load sensor. The classifier achieved over 95% accuracy. (4) Conclusions: Based on these findings, DMAMA has potential for use as a closed-loop control input to adapt semi-active prostheses to different locomotion modes. [ABSTRACT FROM AUTHOR]

(1) Ultimate frisbee involves frequent cutting motions, which have a high risk of anterior cruciate ligament (ACL) injury, especially for female players. This study investigated the in-game cutting maneuvers performed by female ultimate frisbee athletes to understand the movements that could put them at risk of ACL injury. (2) Lower-body kinematics and movement around the field were reconstructed from wearable lower-body inertial sensors worn by 12 female players during 16 league-sanctioned ultimate frisbee games. (3) 422 cuts were identified from speed and direction change criteria. The mean cut had approach speed of 3.4 m/s, approach acceleration of 3.1 m/s2, cut angle of 94 degrees, and ground-contact knee flexion of 34 degrees. Shallow cuts from 30 to 90 degrees were most common. Speed and acceleration did not change based on cut angle. Players on more competitive teams had higher speed and acceleration and reduced knee flexion during cutting. (4) This study demonstrates that a lower-body set of wearable inertial sensors can successfully track an athlete's motion during real games, producing detailed biomechanical metrics of behavior and performance. These in-game measurements can be used to specify controlled cutting movements in future laboratory studies. These studies should prioritize higher-level players since they may exhibit higher-risk cutting behavior. [ABSTRACT FROM AUTHOR]

This study introduces a noninvasive wearable system for investigating tendon loading patterns during outdoor locomotion on variable terrain. The system leverages shear wave tensiometry, which is a new approach for assessing tendon load by tracking wave speed within the tissue. Our wearable tensiometry system uses a battery-operated piezoelectric actuator to induce micron-scale shear waves in a tendon. A data logger monitors wave propagation by recording from two miniature accelerometers mounted on the skin above the tendon. Wave speed is determined from the wave travel time between accelerometers. The wearable system was used to record Achilles tendon wave speed at 100 Hz during 1-km outdoor walking trials in nine young adults. Inertial measurement units (IMUs) simultaneously monitored participant position, walking speed, and ground incline. An analysis of 5108 walking strides revealed the coupled biomechanical effects of terrain slope and walking speed on tendon loading. Uphill slopes increased the tendon wave speed during push-off, whereas downhill slopes increased tendon wave speeds during early stance braking. Walking speed significantly modulated peak tendon wave speed on uphill slopes but had less influence on downhill slopes. Walking speed consistently induced greater early stance wave speeds for all slopes. These observations demonstrate that wearable shear wave tensiometry holds promise for evaluating tendon tissue kinetics in natural environments and uncontrolled movements. There are numerous practical applications of wearable tensiometry spanning orthopedics, athletics, rehabilitation, and ergonomics. [ABSTRACT FROM AUTHOR]