Search

Despite numerous attempts to correct forward head posture (FHP), definitive evidence-based screening and diagnostic methods remain elusive. This study proposes a preliminary diagnostic methodology for FHP, utilizing a noninvasive body angle measurement system as a screening test for FHP and incorporating radiological parameters for sagittal alignment. We enrolled 145 adolescents for FHP screening. The forward neck tilt angle (FNTA), defined as the angle between the vertical line and the line connecting the participant's acromion and tragus, was measured using the POM-Checker (a noninvasive depth sensor-based body angle measurement system). A whole-spine standing lateral radiograph was obtained, and eight sagittal alignment parameters were measured. Statistical analyses of the association between the FNTA and eight sagittal alignment parameters were conducted. We used 70% of the participant data to establish a preliminary diagnostic model for FHP based on FNTA and each sagittal alignment parameter. The accuracy of the model was evaluated using the remaining 30% of the participant data. All radiological parameters of sagittal alignment showed weak statistical significance with respect to FNTA (best case: r = 0.16, p = 0.0500; cranial tilt). The proposed preliminary diagnostic model for FHP demonstrated 95.35% agreement. Notably, the model using FNTA without radiological parameters accurately identified (100%) participants who required radiographic scanning for FHP diagnosis. Owing to the weak statistical significance of the association between radiological parameters and external body angle, both factors must be considered for accurate FHP diagnosis. When a clear and severe angle variation is observed in an external body angle check, medical professionals should perform radiographic scanning for an accurate FHP diagnosis. In conclusion, FNTA assessment of FNTA through the proposed preliminary diagnostic model is a significant screening factor for selecting participants who must undergo radiographic scanning so that a diagnosis of FHP can be obtained. [ABSTRACT FROM AUTHOR]

Considerable research is being conducted on the use of FeF3 as a cathode replacement for FeS2 in thermal batteries. However, FeF3 alone is inefficient as a cathode active material because of its low electrical conductivity due to its wide bandgap (5.96 eV). Herein, acetylene black and multi-walled carbon nanotubes (MWCNTs) were combined with FeF3, and the ratio was optimized. When acetylene black and MWCNTs were added separately to FeF3, the electrical conductivity increased, but the mechanical strength decreased. When acetylene black and MWCNTs were both added to FeF3, the FeF3/M1AB4 sample (with 1 wt.% MWCNTs and 4% AB) afforded a discharge capacity of approximately 74% of the theoretical capacity (712 mAh/g) of FeF3. Considering the electrical conductivity and mechanical strength, this composition was confirmed to be the most suitable. [ABSTRACT FROM AUTHOR]

In this paper, a QR flyback converter using a self-driven active snubber (SDAS) was proposed to solve the problem of voltage surge in the switch of QR flyback converters. In the proposed converter, the SDAS consisting of a clamping capacitor and an active switch can be configured in parallel with the main switch or transformer to reduce the voltage surge in the switch. To confirm the steady-state characteristics of the QR flyback converter to which the proposed SDAS is applied, equivalent circuits for each state were constructed, and the equations and characteristics for each state were determined. A 60 W class small AC–DC adapter was constructed to confirm the effectiveness of the proposed converter and the control circuit method, and the experimental results were analyzed. The size of the experimental AC–DC adapter was 74 × 29 × 23   mm , and it had a high power density of 20   W / in 3 or more. The experimental circuit was limited to the high power conversion efficiency of up to 91.56%, and the maximum voltage surge in the switch was approximately 450 V. One of the reasons for such high efficiency is the SDAS circuit, which sufficiently reduces the voltage surge of the QR flyback switch, compared with the RCD clamp circuit, and does not consume power in principle. [ABSTRACT FROM AUTHOR]

In this study, we propose the use of a short-distance and fixed-type wireless power transmission transformer via a half-bridge LLC resonant converter. A ceramic insulating layer was used instead of an air gap, meaning that the heat generated from the transformer core and the PCB winding was quickly transferred to the external metal case, with the ceramic insulating layer acting as a heat pipe. In order to stabilize the output voltage, we proposed the use of IR photo tunnel technology, and it was applied to two ceramic insulating layers so that the voltage error signal of the secondary output voltage could be transmitted as light to the primary side. As a result, it was possible to physically separate the primary and secondary sides of the power circuit centering on the ceramic insulating layer. The experiment was carried out with the input voltage of 400 V, the output voltage of 54 V, the maximum output power of 1 kW, and the switching frequency of 1.3 MHz or higher. As a result, the maximum operating frequency was 1.83 MHz, and the output voltage stability to the load was 0.49% or lower. The power density of the experimental circuit was 380 W / in 3 or higher, and the maximum power conversion efficiency was approximately 93% or higher. [ABSTRACT FROM AUTHOR]

In this paper, a steady-state model of an LLC resonant half-bridge converter with internal loss resistance is proposed, in order to maximize power conversion efficiency, and steady-state characteristic equations of DC voltage gain and input impedance are derived for the optimal design of the converter. First, to confirm the validity of the steady-state characteristic equation and the optimal design process, a prototype converter with a maximum output of 2 kW was designed. Through comparison of simulation, calculation, and experimental results obtained from the prototype test, it is shown that the calculation results proposed in this paper were closer to the experimental results than the calculation results obtained under the lossless condition. In addition, the relationship between the switching frequency and the load current of the prototype was compared, in order to determine the operating range of the switching frequency, which is important in the converter design stage. In this case, it was confirmed that the calculated value reflecting the internal loss showed a close result. In conclusion, we confirm the usefulness of the analysis results reflecting the internal loss resistance proposed in this paper and the optimal design process. [ABSTRACT FROM AUTHOR]

Ammonium sulfide ((NH4)2S) was used for the passivation of an InP (100) substrate and its conditions were optimized. The capacitance–voltage (C–V) characteristics of InP metal-oxide-semiconductor (MOS) capacitors were analyzed by changing the concentration of and treatment time with (NH4)2S. It was found that a 10% (NH4)2S treatment for 10 min exhibits the best electrical properties in terms of hysteresis and frequency dispersions in the depletion or accumulation mode. After the InP substrate was passivated by the optimized (NH4)2S, the results of x-ray photoelectron spectroscopy (XPS) and the extracted interface trap density (Dit) proved that the growth of native oxide was suppressed. [ABSTRACT FROM AUTHOR]

With advances in internet of things technology and fossil fuel depletion, energy harvesting has emerged rapidly as a means of supplying small electronics with electricity. As a method of enhancing the electrical output of the triboelectric nanogenerator, specialized for harvesting mechanical energy, structural modification to amplify the input force is receiving attention due to the limited input energy level. In this research, a lever structure was employed for delivering the amplified input force to a triboelectric nanogenerator. With structural optimization of a 2.5 cm : 5 cm distance ratio of the first and second parts using two lever structures, the highest electrical outputs were achieved: a V OC of 51.03 V, current density of 3.34 mA m -2 , and power density of 73.5 mW m -2 at 12 MΩ in the second part. As applications of this triboelectric generator, a vertical vibration sensor and a wearable reloading trigger in a gun shooting game were demonstrated. The possibility for a wearable finger bending sensor with low-level input was checked using a minimized device. Enhanced low-detection limit with amplified input force from the structural advantage of this lever-based triboelectric nanogenerator device can expand its applicability to the mechanical trigger for wearable electronics.