Search

Alkaline–surfactant–polymer (ASP) flooding, a recognized method for oil recovery, encounters limited use due to its expense. In addition, ASP's best composition and injection sequence still remains uncertain today. This study explores conventional ASP flooding using PT SPR Langgak's special surfactants, simulating Langgak oilfield conditions in Sumatra, Indonesia. By comparing the outcomes of this flooding technique with that of starch-assisted ASP performed in another study, the benefits of adding starch nanoparticles to flooding are evident. Nano-starch ASP increased oil recovery by 18.37%, 10.76%, and 10.37% for the three configurations investigated in this study. Water flooding preceded ASP flooding, and flooding operations were carried out at 60 °C. This study employed sodium hydroxide (NaOH), sodium carbonate (Na2CO3), and specialized surfactants from PT SPR. The adopted polymer is solely hydrolyzed polyacrylamide (HPAM) at 2000 ppm. Starch nanoparticles underwent comprehensive characterization and focused more on charge stability. Purple yam nanoparticles (PYNPs) exhibited remarkable stability at −36.33 mV, unlike cassava starch nanoparticles (CSNPs') at −10.68 mV and HPAM's at −27.13 mV. Surface properties affect interactions with fluids and rocks. Crystallinity, a crucial characterization, was assessed using Origin software 2019b. CSNPs showed 24.15% crystallinity, surpassing PYNPs' 20.68%. Higher crystallinity benefits CSNPs' thermal stability. The amorphous behavior found in PYNPs makes them less suitable if applied in harsh reservoirs. This research correlated with prior findings, reinforcing starch nanoparticles' role in enhancing oil recovery. In summary, this study highlighted conventional ASP flooding using HPAM as the sole polymer and compared it with three formations that used two starch nanoparticles included with HPAM, assessing their impact on charge stability, crystallinity, and recovery rate to emphasize their importance in the oil recovery industry. Starch nanoparticles' benefits and limitations guided further investigation in this study. [ABSTRACT FROM AUTHOR]

This study aimed to address the challenges faced by mature oilfields in extracting substantial oil quantities. It focused on improving the efficiency of alkaline–surfactant–polymer (ASP) flooding technique, which is a proven tertiary recovery technology, to overcome scaling issues and other hindrances in its large-scale implementation. Appropriate materials and their suitable concentrations were selected to enhance the ASP flooding technique. Special surfactants from Indonesia were introduced to improve the interfacial tension reduction and wettability alteration. Reservoir rock model that resembling Langgak oilfield in Sumatra was utilized, and low-salinity water was employed to mimic the oilfield conditions. Starches derived from cassava nanoparticles (CSNPs) and purple yam nanoparticles (PYNPs) were combined separately with conventional hydrolyzed polyacrylamide (HPAM) polymer to enhance its performance. Sodium hydroxide and sodium carbonate were used as alkaline in final ASP formula. It was demonstrated from this research that only two combinations of ASP formulations have led to improved oil recovery. One combination utilizing PYNPs resulted in 39.17% progressive recovery, while the other combination incorporating CSNPs achieved 35% incremental oil recovery. The ASP combination that resulted in recovery rate of 39.17% was composed of sodium hydroxide (NaOH) at a concentration of 1.28 wt.%, PSC EOR 2.2 (0.98 wt.%), and a combined polymer consisting of HPAM (0.2 wt.%) and PYNPs nano-starch (0.6 wt.%). The second combination led to 35% recovery rate and involved NaOH also at concentration 1.28 wt.%, PSC HOMF (0.63 wt.%), and a combined polymer comprising from HPAM (0.2 wt.%) and CSNPs nano-starch (0.8 wt.%). These findings of this study highlighted the potential of this modified ASP flooding to enhance oil recovery in mature oilfields, thereby offering valuable insights for oil industry. [ABSTRACT FROM AUTHOR]

Significant amounts of oil remain in the reservoir after primary and secondary operations, and to recover the remaining oil, enhanced oil recovery (EOR) can be applied as one of the feasible options remaining nowadays. In this study, new nano-polymeric materials have been prepared from purple yam and cassava starches. The yield of purple yam nanoparticles (PYNPs) was 85%, and that of cassava nanoparticles (CSNPs) was 90.53%. Synthesized materials were characterized through particle size distribution (PSA), Zeta potential distribution, Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and transmission electron microscopy (TEM). The performance of PYNPs in recovering oil was better than CSNPs, as found from the recovery experiments. Zeta potential distribution results confirmed the stability of PYNPs over CSNPs (−36.3 mV for PYNPs and −10.7 mV for CSNPs). The optimum concentration for these nanoparticles has been found from interfacial tension measurements and rheological properties, and it was 0.60 wt.% for PYNPs and 0.80 wt.% for CSNPs. A more incremental recovery (33.46%) was achieved for the polymer that contained PYNPs in comparison to the other nano-polymer (31.3%). This paves the way for a new technology for polymer flooding that may replace the conventional method, which depends on partially hydrolyzed polyacrylamide (HPAM). [ABSTRACT FROM AUTHOR]

Based on our prior research, we synthesized iron-oxide nanoparticles (IONPs) in two shapes (spherical and cubic) and sized them for the current inquiry. This research examined the magnetic, rheological, and sedimentation properties of the suspensions containing PEG-coated IONPs, considering that both produced particles are intended to be employed for magnetic targeting applications. The saturation magnetization of both IONPs was lower than the magnetite domain magnetization of 92 emu/g due to the surfactant and the dead surface magnetic layer. Under each investigated magnetic field (0, 34 and 183 mT), the shear viscosity behaviour of the MNP suspensions of both kinds was comparable. Shear thinning behaviour was seen for both particle suspensions in the low shear rate area (0.1 s−1 to 1 s−1). The rheological curves from this paper show that the suspensions present a higher viscosity at lower shear rates for spherical and cubic PEG-coated nanoparticles when a magnetic field is applied. The aggregation behaviour demonstrates that cubic-shaped IONPs are more stable throughout time, with hydrodynamic diameter measurements showing a relatively slow variation of the DLS size distribution from 250 nm to 210 nm in the first 600 s; contrarily, the hydrodynamic diameter of spherical IONPs fluctuated significantly, from 855 nm to 460 nm. Another key finding relates to the sedimentation profile, specifically that PEG-coated IONPs with spherical shapes have a stronger tendency to sediment than those with cubic forms, which are more stable. [ABSTRACT FROM AUTHOR]

We report the synthesis and properties of temperature- and pH-responsive p([NIPAm-co-PEGMA] (core)/[NIPAm-co-AAc] (shell)) nanogels with narrow size distributions, tunable sizes and increased drug loading efficiencies. The core-shell nanogels were synthesized using an optimized two-stage seeded polymerization methodology. The core-shell nanogels show a narrow size distribution and controllable physico-chemical properties. The hydrodynamic sizes, charge distributions, temperature-induced volume phase transition behaviors, pH-responsive behaviors and drug loading capabilities of the core-shell nanogels were investigated using transmission electron microscopy, zeta potential measurements, dynamic light scattering and UV-Vis spectroscopy. The size of the core-shell nanogels was controlled by polymerizing NIPAm with crosslinker poly(ethylene glycol) dimethacrylate (PEGDMA) of different molecular weights (Mn-200, 400, 550 and 750 g/mol) during the core synthesis. It was found that the swelling/deswelling kinetics of the nanogels was sharp and reversible; with its volume phase transition temperature in the range of 40-42 °C. Furthermore, the nanogels loaded with l-3,4-dihydroxyphenylalanine (L-DOPA), using a modified breathing-in mechanism, showed high loading and encapsulation efficiencies, providing potential possibilities of such nanogels for biomedical applications. [ABSTRACT FROM AUTHOR]

In recent years, several studies have indicated the impact of nanoparticles (NPs) on various properties (such as viscosity and fluid loss) of conventional drilling fluids. Our previous study with commercial iron oxide NPs indicated the potential of using NPs to improve the properties of a laboratory bentonite-based drilling fluid without barite. In the present work, iron oxide NPs have been synthesized using the co-precipitation method. The effect of these hydrophilic NPs has been evaluated in bentonite and KCl-based drilling fluids. Rheological properties at different temperatures, viscoelastic properties, lubricity, and filtrate loss were measured to study the effect of NPs on the base fluid. Also, elemental analysis of the filtrate and microscale analysis of the filter cake was performed. Results for bentonite-based fluid showed that 0.019 wt% (0.1 g) of NPs reduced the coefficient of friction by 47%, and 0.0095 wt% (0.05 g) of NPs reduced the fluid loss by 20%. Moreover, for KCl-based fluids, 0.019 wt% (0.1 g) of additive reduced the coefficient of friction by 45%, while higher concentration of 0.038 wt% (0.2 g) of NPs shows 14% reduction in the filtrate loss. Microscale analysis shows that presence of NPs in the cake structure produces a more compact and less porous structure. This study indicates that very small concentration of NPs can provide better performance for the drilling fluids. Additionally, results from this work indicate the ability of NPs to fine-tune the properties of drilling fluids. [ABSTRACT FROM AUTHOR]