Search

It is difficult for the existing Burgers model to accurately depict the off-axis cyclic drawing process of woven coatings. In this paper, the mechanical deformation of woven PVC (polyvinyl chloride)-coated film at different temperatures is investigated. One-dimensional (1D) and two-dimensional (2D) constitutive models were established to characterize cyclic deformation processes. The 1D model is an improved Burgers model. The effects of the time dependence of the viscosity coefficient and the ratio of elastic to viscous deformation are considered simultaneously. The accuracy of the 1D model for predicting the cyclic nonlinear deformation at different temperatures and loading rates is improved. The 2D model is a nonlinear orthotropic model using polynomials. On the basis of the single-objective genetic algorithm, the inverse algorithm is used to obtain the shear polynomial coefficients in the tension phase and the shear modulus in the unloading phase, which circumvents performing the difficult shear test. UMAT subroutines of off-axis stretching and off-axis cyclic stretching are written separately. The intelligent inverse algorithm program consists of a single-objective genetic algorithm program, a finite element parametric modelling program, and a UMAT subroutine. The simulation results are compared with the off-axis cyclic tensile test data to validate the effectiveness and accuracy of the proposed 2D model for the analysis of the woven PVC-coated films in the tension–shear coupling state. [ABSTRACT FROM AUTHOR]

This study is conducted on glass fiber-reinforced composite honeycomb sandwich structures by introducing delamination damage through low-velocity impact tests, establishing a three-dimensional progressive damage analysis model, and evaluating the delamination damage characteristics and laws of honeycomb sandwich structures under different impact energies through experiments. Repair techniques and process parameters for delamination damage are explored. It is found that as the impact energy increases, the damage area of honeycomb sandwich panels also increases, and the delamination damage extends from the impact center to the surrounding areas, accompanied by damage such as fiber fracture and matrix cracking. The strength recovery rates of sandwich panels at impact energies of 5 J, 15 J, and 25 J after repair are 71.90%, 65.89%, and 67.10%, respectively, which has a considerable repair effect. In addition, a progressive damage model for low-velocity impact on the composite honeycomb sandwich structure is established, and its accuracy and reliability are verified. [ABSTRACT FROM AUTHOR]

In this paper, a new multi-part composite frangible cover (MCFC) was designed and fabricated. The frangible cover, manufactured with a traditional manual lay-up method, is designed to conduct a simulated missile launch test using a specially developed test device. A weak zone structure of the composite multi-part frangible cover was designed, and the separation process of the cover was studied by numerical simulation. Based on the strength envelope of the weak zone and the equal-strength design principle, a design method for the weak zone structure of the composite multi-part frangible cover was proposed. A finite element model of the composite multi-part frangible cover was established, and the separation process was numerically simulated and analyzed. Afterward, the verification experiments were carried out. Close agreements between the numerical and experimental results are observed. [ABSTRACT FROM AUTHOR]

In this paper, the effect of interlaminar properties and the type of delamination defects on the residual compression properties of carbon fiber laminates were experimentally investigated. A new method, which employed magnetic force to guide the arrangement direction of stainless steel particles between layers of laminates, was adopted to improve the interlayer toughness. The digital image correlation, C-scan, and micro-CT were used to measure and identify the compression failure damages. Test results showed that the compressive strength of the intact carbon fiber laminates was 299.37 MPa, and the one of specimens containing the deeply buried delamination, the through-width delamination, and the surface delamination decreased by 55.98 MPa, 58.69 MPa, and 60.23 MPa, respectively. The compressive strength of the specimens containing the deeply buried delamination only decreased by 14.01 MPa when the mode I toughness increased by 81.88%, and the specimen containing the surface delamination only decreased by 30.86 MPa when the mode II fracture toughness increased by 87.72%. However, improving the fracture toughness could not strengthen the specimens containing the through-width delamination. Moreover, a qualitative dynamic damage relationship, which described the relationship between delamination expansion and compression damage vividly, was proposed. The reason the increase of the toughness could improve the residual compression performance of the laminates containing delamination was that the higher fracture toughness hindered the secondary expansion of the delamination during the compression process so that the delamination area could almost remain unchanged. [ABSTRACT FROM AUTHOR]

This paper presents a thermal stress analysis of the adhesive structure to study the effect of temperature change on the performance of the resin layer. The adhesive structure's finite element model (FEM) is established, and the verified test is conducted in an environmental chamber. The simulated predictions are in good agreement with the experimental data. Subsequently, the effect of thickness of the resin layer, the elastic modulus of sheet materials, and vertex angle on the thermal behavior of the adhesive structure are discussed. The results show that the stiffness of sheet materials and vertex angle have a limited influence on the thermal stress of the resin layer. It is beneficial to reduce its thermal stress by increasing the height of the resin layer. In addition, the difference in thermal expansion coefficients between the upper and bottom sheets is the major cause of thermal stress in the resin layer. [ABSTRACT FROM AUTHOR]