Search

Co-melting paracetamol with different cellulose derivatives leads to full or partial amorphization of active substance. The aim of this study was to determine whether the amorphization of paracetamol after co-melting with cellulose derivatives is stable and whether it depends on the type of cellulose derivative added and the ratio of components. Mixtures of paracetamol with cellulose derivatives containing different proportions of components were prepared. Using differential scanning calorimetry (DSC), the samples were melted and the amorphization of paracetamol was confirmed. After 2 and 4 months, the samples were reanalyzed to determine the amorphization stability during storage and the difference in the effect of different polymers on the amorphization stability. The physical mixtures were additionally tested using Fourier transform infrared (FTIR) and Raman spectroscopic methods to confirm that no solid-phase interactions were noticed. Samples were also analyzed using ultrahigh-performance liquid chromatography (UHPLC) to assess the effect of co-melting and storage on the chemical stability of paracetamol. The results show that paracetamol amorphizes after co-melting with cellulose derivatives. The crystallization of paracetamol after co-melting depends on the polymer used and the proportions of the components. No interactions between the components and the chemical stability of paracetamol in the tested samples were confirmed. [ABSTRACT FROM AUTHOR]

Choosing the right phase change material (PCM) for a thermal energy storage (TES) application is a crucial step in guaranteeing the effectiveness of the system. Among a variety of PCMs available, the choice for a given application is established by several key factors, e.g., latent heat, stability, and melting point. However, phenomena such as subcooling—for which PCM cools in a liquid state below its solidification point—can lead to a reduction in the amount of energy stored or released, reducing the TES overall effectiveness, and also in some inaccuracies when modeling the problem. Thus, understanding the effects of subcooling on PCM performance is crucial for modeling and optimizing the design and the performance of TES systems. To this end, this work analyzes the PCM discharging phase in a cold thermal energy storage coupled to a chiller system. A first conduction-based predictive model is developed based on enthalpy–porosity formulation. Subcooling phenomena are encompassed through a control variable formulation, which takes its cue from the operation of a thermostat. Then, thermal properties of the PCM, i.e., the phase change range and specific heat capacity curve with temperature, are evaluated by using differential scanning calorimetry (DSC), in order to derive a second predictive model based on these new data, without including subcooling, for the sake of comparison with the first one. Experimental results from the storage tank confirm both model reliability and the fact that the PCM suffers from subcooling. Between the two numerical models developed, the first one that considers subcooling proves it is able to predict with satisfactory accuracy (RMSE < 1 °C) the temperature evolution on different tank levels. [ABSTRACT FROM AUTHOR]

Ever since the introduction of 3D printing, industries have seen an exponential growth in production and efficiency. Three-dimensional printing is the process of additive manufacturing (AM) in which the conventional method of material removal is challenged. Layer-on-layer deposition is the basic principle of the AM. Additive manufacturing technologies are used to create 3D-printed objects. An object is built in an additive technique by laying down successive layers of material until the object is complete. Each of these layers can be viewed as a cross-section of the item that has been lightly cut. When compared to traditional production methods, 3D printing allows the creation of complicated shapes with less material. In conventional methods, the materials go through several damages due to the tool–workpiece contact creating friction between them and the dissipated heat that damages the material. Overcoming the conventional method of machining with the help of 3D printing is a new advancement in the industries. The process involves using non-conventional methods for the machining of the parts. This research was oriented towards the chemical vapor jet drilling of the acrylonitrile–butadiene–styrene (ABS) materials. ABS materials are highly machinable and can be recycled for further usage. This paper focused on the usage of acetone as the chemical for drilling. The surface roughness and circularity of the drilled hole was taken into account for this research paper. We set up a manual experiment to run tests and get results. A vapor jet machine was designed with acetone as the core for the vapor. Various analyses were also formulated and conducted during experimentations. Surface roughness analysis provided the insight of roughness after the machining with the help of acetone vapor jet spray. SEM and micro-image parameters were also considered for more clear and advanced reports. In this research paper, DSC and FTIR analysis were performed to understand changes in the internal structure and the material properties of the ABS. Moreover, the research aimed to investigate the effect of various inputs processing parameters such as pressure, flow rate, and stand-off distance on the surface roughness and circularity of ABS workpiece material. The Taguchi L9 orthogonal array design was utilized to conduct tests by chemical vapor jet drilling using acetone and to evaluate the performance of the set-up while reducing the influence of interfering factors in order to provide reliable surface finish and circularity results. The results and conclusion of the research paper aimed to determine the most suitable parameters for the non-conventional acetone vapor jet drilling of the ABS material. The theoretical calculations predicted 1.64432 and 0.3289080 values of surface roughness and circularity, respectively. On the other hand, the experimental values were recorded as 1.598 for surface roughness and 0.322 for circularity. Therefore, a negligible error of 0.046 for surface roughness and 0.0031 for circularity, respectively, was noted which validate the statistical equations and the consistency of the combined vapor jet drilling process. [ABSTRACT FROM AUTHOR]

In this study, we investigated the impact of reaction temperature on the physicochemical, structural, morphological, and thermal properties of sodium alginate/poly (vinyl alcohol)-based hydrogels, both in the pure form and with the addition of 20% (v/v) Aloe vera solution. The materials were prepared by chemical crosslinking at temperatures in the range of 65–75 °C. Poly (ethylene glycol) diacrylate was used as a crosslinking agent. The extent to which the crosslinking reaction proceeded was studied as a function of the reaction temperature, along with the thermal properties and morphology of the final materials. A measurement of gel fraction, in agreement with differential scanning calorimetry and Fourier transform infrared spectroscopy, showed that a higher temperature of reaction promoted the crosslinking reaction. On the basis of the aforementioned techniques, as well as by energy dispersive X-ray analysis under an electron microscope, it was also shown that the bioadditive Aloe vera promoted the crosslinking reaction. [ABSTRACT FROM AUTHOR]

Effect of high molybdenum content ~10% as an alloying element on the strength and microstructural properties of 11% nickel—1.25% titanium maraging steel was evaluated. To increase the homogeneity and cleanliness of produced ingot, the investigated steel sample was produced by melting the raw material in an open-air induction melting furnace followed by refining utilizing a direct current electro-slag refining machine. The produced steel samples were both forged and heat-treated in optimum condition to acquire the full capacity of mechanical properties especially the tensile properties. After Forging and heat treatment at optimum condition, steel samples were evaluated by optical microscopy (OM), X-ray diffraction (XRD), differential scanning calorimetry (DSC) analysis, electron backscattering diffraction (EBSD), and transmission electron microscopy (TEM). The experimental data showed that this steel sample has ultimate strength ~2100 MPa and elongation around 14%. High tensile properties obtained may be attributed on one hand due to the presence of high alloying lamellar martensite phase and lamellar austenite phase which has high dislocation intensity, and on the other hand, due to the high homogeneity and cleanliness of investigated samples from large nonmetallic inclusions. The results also show that a high amount of intermetallic compounds (NiMo3 and NiTi3) which are completely round and have a very low size not more than hundred nanometers. [ABSTRACT FROM AUTHOR]

This study aimed to assess the developed nonwoven inserts with aerogel/PCM (phase change material) microcapsules for use in protective clothing against cold in terms of properties related to thermophysiological comfort. These inserts were obtained by the thermal bonding of a multilayer system consisting of needled-punched nonwovens and silica aerogel particles and/or PCM microcapsules evenly distributed between them. The influence of aerogel and PCM microcapsules on the basic physical properties of inserts, their microstructure, air permeability, and water vapor resistance was investigated and analyzed. The thermal insulation properties of inserts were assessed based on thermal conductivity results. The inserts with PCMs were also tested for their ability to regulate the temperature in the undergarment microclimate using the differential scanning calorimeter (DSC) and the "skin model" device. The research showed that the use of aerogel allowed for reducing the thermal conductivity of the insert by approximately 13% compared to the insert without additives. The high values obtained of the melting and crystallization enthalpy of inserts with PCMs confirmed their high efficiency in the heat absorption and release. Thus, the use of aerogel and PCMs in protective clothing against cold seems to be an effective solution for improving its protective properties and actively adapting its thermal insulation to the changing temperature conditions and the activity level of employees.

The polylactic acid (PLA) resin Ingeo 4032D was selected as the research object. Epoxy soybean oil (ESO) and zeolite (3A molecular sieve) were used as plasticizer and reinforcing filler, respectively, for PLA blend modification. The mixture was granulated in an extruder and then blown to obtain films under different conditions to determine the optimum processing temperatures and screw rotation. Then, the thermal behaviour, crystallinity, optical transparency, micro phase structure and physical properties of the film were investigated. The results showed that with increasing zeolite content, the crystallization behaviour of PLA changed, and the haze of the film increased from 5% to 40% compared to the pure PLA film. Zeolite and ESO dispersed in the PLA matrix played a role in toughening and strengthening. The PLA/8 wt% zeolite/3 wt% ESO film had the highest longitudinal tensile strength at 77 MPa. The PLA/2 wt% zeolite/3 wt% ESO film had the highest longitudinal elongation at 13%. The physical properties depended heavily on the dispersion of zeolite and ESO in the matrix. [ABSTRACT FROM AUTHOR]

The paper presents a comparative analysis of the circular and flat cross-section belts using measurements of a set of thermomechanical parameters, contributing to research about hot plate welding of drive belts. On the basis of thermogravimetric and spectrophotometric tests, information about the same chemical composition of the two belts was obtained. Dynamic thermomechanical analysis and scanning differential calorimetry provided information about a small difference between belts, which disappeared when the material was placed in a state of increased temperature and mechanical stress. On the basis of the analysis of the specific heat, thermal diffusion, density, and hardness, the values of the selected thermal properties of the belt were obtained, and a large similarity between the belts was identified. On the basis of the novel performed test cycle, it has been hypothesized that circular and flat belts made from thermoplastic polyurethane elastomer could be used interchangeably for butt-welding testing. It has also been proven that cyclic thermomechanical loads unify the properties of both materials so that multiple mechanical and thermal loads do not result in any change in the material properties of the two belts. As a consequence, changes in the weld properties after welding, compared to a solid belt, are not expected. [ABSTRACT FROM AUTHOR]