Search

The combination of different wood-modification technologies to obtain improved performance is increasingly receiving attention in research. In this study, Scots pine (Pinus sylvestris) sapwood was impregnated with furfuryl alcohol (FFA) in pure aqueous 20, 40, and 60% solution strength without adding any catalyst. In a second step, the FFA was polymerized while simultaneously performing thermal modification in a closed system at 130, 150, or 180 °C. After leaching and ageing tests, the nine different combinations were tested in use class 4 applications (in contact with or very close to the ground and frequently wet) according to CEN/TS 15083-2 (2005) decay laboratory test. It was noted that even the minimum-intensity combination of 20% FFA at 130 °C resulted in maximum durability class (DC) 1 performance. On the contrary, DC 4 was assigned to thermally modified control samples, even at the maximum intensity of thermal modification. Similarly, for FFA modifications, previous research has suggested that an uptake of 35% solution strength is required to obtain an adequate durability performance in use class 4 applications. High levels of resistance against termites were also noted by corresponding termite lab tests. Moisture studies showed the combined treatments resulted in improved stability and reduced moisture uptakes. Thus, the results obtained by this study revealed synergistic performance effects, which originate from the combined thermo-chemical modification approach, and which were higher than simple accumulation of the individual performance of purely thermally or chemically modified wood. Thus, the presented findings have provided positive implications for industrial applications of thermo-chemical modification techniques and offers an array of new research opportunities. [ABSTRACT FROM AUTHOR]

The application of tree of heaven (Ailanthus altissima (Mill.) Swingle) is constrained by its poor durability and dimensional stability. Despite exhibiting promising physical and mechanical properties comparable to ash wood (Fraxinus excelsior L.), it is regarded as an invasive species and receives limited attention in wood property enhancement research. This study subjected tree of heaven to heat treatment at 180 °C and 200 °C to investigate its sorption characteristics using dynamic vapor sorption tests. The results revealed a 13% reduction in equilibrium moisture content at 95% relative humidity and 25 °C after thermal modification at 180 °C and a 25% reduction after thermal modification at 200 °C. Increasing the treatment temperature lowered the moisture content ratio to 0.76 and shortened the conditioning time by up to 10%. The highest hysteresis, ranging from 3.39% to 3.88%, was observed at 70% relative humidity. [ABSTRACT FROM AUTHOR]

The durability against decay organisms is an essential material property for wood in outdoor use. A jack of all trades method for above-ground wood durability testing has been sought for decades, but until now no method has found its way into European standardization. The method of choice shall be applicable for untreated and treated wood—ideally also for wood composites. It shall further be reproducible, objective, fast, easy, and inexpensive. Finally, it shall provide high predictive power. This study was aimed at a review of results and practical experience with the Bundle test method which could serve as a standard procedure for above-ground field tests of wood-based materials. The method allows for water-trapping, creates a moderate moisture-induced decay risk typical for UC 3 situations, and was found applicable for a wide range of wood materials. The method allows for rapid infestation and failure of non-durable reference species within five years in Central Europe. Based on results from Bundle tests with different modifications and performed at different locations, a guideline has been developed. The method is recommended as a suitable tool for determining the durability of various wood-based materials including modified and preservative-treated wood and can provide data for durability classification. [ABSTRACT FROM AUTHOR]

Wood modifications are becoming popular as a way to enhance the performance of wood, either to make it more durable, improve the performance of wood, or give it new functionality as a multifunctional or smart material. While wood modifications have been examined since the early 1900s, the topic has become a dominant area of study in wood science over the past decade. This review summarizes recent advances and provides future perspective on a selection of wood modifications, i.e., the methods that are currently commercialized (acetylation, furfurylation, and thermal modification), a rediscovered ancient practice (charring), a family of polymerization modifications that have so far made it to the pilot scale, and examples of novel wood-based functional materials explored at laboratory scale. [ABSTRACT FROM AUTHOR]

Recent studies showed treatments with sorbitol and citric acid (SorCA) to significantly improve the dimensional stability and biological durability of wood. The industrialization of this process requires a quality control (QC) method to determine if the fixated chemicals are homogenously distributed within the piece of wood, which is essential for uniform material performance. Therefore, the objective of this work was to evaluate the use of common electromagnetic radiation-based methods to determine the degree of modification in SorCA-treated wood. Both Fourier transform infrared (FTIR) spectroscopy and near-infrared (NIR) spectroscopy have been used to create rough calibrations for the weight percent gain (WPG) prediction models. The FTIR measurements resulted in a high linear correlation between the band area ratio (BAR) and the WPG (R2 = 0.93). Additionally, a partial least square (PLS) regression of NIR spectroscopic data resulted in a model with a high prediction power (R2 = 0.83). Furthermore, X-ray density profiling emerged as a simple alternative for the QC by showing a gradient of modification chemicals inside the sample and differences in chemical uptake between earlywood and latewood. Overall, it can be concluded that the results from FTIR, NIR and X-ray densitometry can serve as indicators of impregnation chemical distribution in SorCA-modified wood. [ABSTRACT FROM AUTHOR]

Durability-based designs with timber require reliable information about the wood properties and how they affect its performance under variable exposure conditions. This study aimed at utilizing a material resistance model (Part 2 of this publication) based on a dose–response approach for predicting the relative decay rates in above-ground situations. Laboratory and field test data were, for the first time, surveyed globally and used to determine material-specific resistance dose values, which were correlated to decay rates. In addition, laboratory indicators were used to adapt the material resistance model to in-ground exposure. The relationship between decay rates in- and above-ground, the predictive power of laboratory indicators to predict such decay rates, and a method for implementing both in a service life prediction tool, were established based on 195 hardwoods, 29 softwoods, 19 modified timbers, and 41 preservative-treated timbers. [ABSTRACT FROM AUTHOR]

Service life planning with timber requires reliable models for quantifying the effects of exposure-related parameters and the material-inherent resistance of wood against biotic agents. The Meyer-Veltrup model was the first attempt to account for inherent protective properties and the wetting ability of wood to quantify resistance of wood in a quantitative manner. Based on test data on brown, white, and soft rot as well as moisture dynamics, the decay rates of different untreated wood species were predicted relative to the reference species of Norway spruce (Picea abies). The present study aimed to validate and optimize the resistance model for a wider range of wood species including very durable species, thermally and chemically modified wood, and preservative treated wood. The general model structure was shown to also be suitable for highly durable materials, but previously defined maximum thresholds had to be adjusted (i.e., maximum values of factors accounting for wetting ability and inherent protective properties) to 18 instead of 5 compared to Norway spruce. As expected, both the enlarged span in durability and the use of numerous and partly very divergent data sources (i.e., test methods, test locations, and types of data presentation) led to a decrease in the predictive power of the model compared to the original. In addition to the need to enlarge the database quantity and improve its quality, in particular for treated wood, it might be advantageous to use separate models for untreated and treated wood as long as the effect of additional impact variables (e.g., treatment quality) can be accounted for. Nevertheless, the adapted Meyer-Veltrup model will serve as an instrument to quantify material resistance for a wide range of wood-based materials as an input for comprehensive service life prediction software. [ABSTRACT FROM AUTHOR]

The service life of wood in outdoor use under humid conditions is mainly determined by its material resistance and the exposure situation. Different standards such as EN 350 (2016) point on the relevance of wood's resistance against moisture for its expected service life. Recently, different standardized but also numerous nonstandardized methods were suggested to test the water permeability of wooden materials. In the context of this study, different European-grown soft- and hardwoods, tropical hardwoods, modified wood and wood treated with water- and oil-borne preservatives were subjected to floating and submersion tests according to CEN/TS 16818 (2018) and different short-term water uptake and release tests. Moisture performance data from field tests with the same materials were analyzed and used to assess the predictive power of different laboratory moisture indicators. The moisture characteristics suggested by CEN/TS 16818 (2018)—rm168 (residual moisture content after water uptake and release processes) and res312 (residue as a percentage of the absorbed moisture)—showed the little potential to predict the outdoor moisture performance of the tested materials. In contrast, the mean moisture content during absorption and desorption (MCmean) predicted well the outdoor moisture performance of the materials under test. Short-term water uptake and release of small specimens also showed high predictive power. [ABSTRACT FROM AUTHOR]

The importance of thermal modification is increasing worldwide. Increased use of thermally modified timber (TMT) has resulted in a need for reliable quality control, comprising control of variation of the production within defined limits, allowing third-party control in the case of certification and the regulation of customer complaints and claims. Techniques are thus needed to characterise the modification of quality in terms of improved target properties of TMT during industrial production, and of TMT products that have been in service for an arbitrary time. In this study, we aimed to utilise dynamic vapor sorption (DVS) for this purpose. Norway spruce (Picea abies) and European beech (Fagus sylvatica) samples were thermally modified at different temperatures according to different heat treatment techniques: (1) the Silvapro process based on an initial vacuum; (2) an air heat treatment, whereby samples were wrapped in aluminium foil; (3) thermal modification of wood samples in the ambient atmosphere in a laboratory oven. Wood samples from closed processes were analysed for validation. TMT was characterised with respect to mass loss, colour and density. Mass loss of wood due to modification (MLTM) was correlated with factors derived from DVS analysis. The present DVS measurements suggest that the equilibrium wood moisture content (EMC95% RH), the time to reach 10% wood moisture content (t10% MC), and the elongation factor, c, derived from a logarithmic function, can serve as alternative parameters to characterise the quality of several thermal modification processes. Further studies are recommended using other wood species, different modification processes and further parameters gained from DVS measurements to understand the robustness and the predictive power of the applied technique. [ABSTRACT FROM AUTHOR]

Sapling-wood products from different wood species such as willow (Salix spp. L.) and Common hazel (Corylus avellana L.) are frequently used for gardening and outdoor decoration purposes. Remaining bark is suggested to provide additional biological durability. Even for temporary outdoor use it seemed questionable that durability of juvenile sapwood can provide acceptably long service lives of horticultural products. Therefore, sapling-wood from seven European-grown wood species was submitted to laboratory and field durability tests. In field tests, specimens with and without bark were tested in comparison and submitted to differently severe exposure situations, i.e., in-ground contact, and above-ground situations with and without water trapping. All materials under test were classified 'not durable' independently from any potential protective effect of remaining bark, which contradicted their suitability for outdoor applications if multi-annual use is desired. [ABSTRACT FROM AUTHOR]

Background and Objectives: In the near future, in Europe a raised availability of hardwoods is expected. One possible sales market is the building sector, where medium dense European hardwoods could be used as load bearing elements. For the hardwood species beech, oak, and sweet chestnut technical building approvals already allow the production of hardwood glulam. For the species maple and ash this is not possible yet. This paper aims to evaluate the economic feasibility of glulam production from low dimension ash and maple timber from thinnings. Therefore, round wood qualities and the resulting lumber qualities are assessed and final as well as intermediate yields are calculated. Materials and Methods: 81 maple logs and 79 ash logs cut from trees from thinning operations in mixed (beech) forest stands were visually graded, cant sawn, and turned into strength-graded glulam lamellas. The volume yield of each production step was calculated. Results: The highest volume yield losses occur during milling of round wood (around 50%) and "presorting and planning" the dried lumber (56%–60%). Strength grading is another key process in the production process. When grading according to DIN 4074-5 (2008), another 40%–50% volume loss is reported, while combined visual and machine grading only produces 7%–15% rejects. Conclusions: Yield raise potentials were identified especially in the production steps milling, presorting and planning and strength grading. [ABSTRACT FROM AUTHOR]

The structural integrity of wood is closely related to its brittleness and thus to its suitability for numerous applications where dynamic loads, wear and abrasion occur. The structural integrity of wood is only vaguely correlated with its density, but affected by different chemical, physico-structural and anatomical characteristics, which are difficult to encompass as a whole. This study aimed to analyze the results from High-Energy Multiple Impact (HEMI) tests of a wide range of softwood and hardwood species with an average oven-dry wood density in a range between 0.25 and 0.99 g/cm³ and multifaceted anatomical features. Therefore, small clear specimens from a total of 40 different soft- and hardwood species were crushed in a heavy vibratory ball mill. The obtained particles were fractionated and used to calculate the 'Resistance to Impact Milling (RIM)' as a measure of the wood structural integrity. The differences in structural integrity and thus in brittleness were predominantly affected by anatomical characteristics. The size, density and distribution of vessels as well as the ray density of wood were found to have a significant impact on the structural integrity of hardwoods. The structural integrity of softwood was rather affected by the number of growth ring borders and the occurrence of resin canals. The density affected the Resistance to Impact Milling (RIM) of neither the softwoods nor the hardwoods. [ABSTRACT FROM AUTHOR]