Search

The paper describes the type of changes in the structure and mechanical properties of 3D printed shapes under the influence of mineral oil. The effects of a room (23 °C) and elevated temperature (70 °C) on 3D prints manufactured by the FDM method and stored in oil for 15, 30, and 60 days on the change of properties and structure were investigated. The samples were produced from ABS (poly(acrylonitrile-co-butadiene-co-styrene)), ASA (poly(acrylonitrile-co-styrene-co-acrylate), PLA (poly(lactic acid)), and HIPS (high-impact polystyrene). Tests related to the strength of the materials, such as the static tensile test and Charpy impact test, were carried out. The structure was evaluated using a scanning electron microscope, and changes in chemical structure were determined by conducting FTIR (Fourier transform infrared spectroscopy) and TGA (thermogravimetric analysis) tests. The analysis of the results provided important information about the impact of mineral oil on specific materials. This is critical for designing and manufacturing components that can withstand mineral oil exposure in real-world environments. The materials underwent varying changes. Strength increased for PLA by about 28%, remained unchanged for ABS and HIPS during exposure for 30 days, and decreased for ASA with extended exposure up to 14%. [ABSTRACT FROM AUTHOR]

The purpose of this study is to determine the material properties of CFRP composites in the form of a fabric for the construction of racing car bodywork. This work focused on the determination of the strength and tribological properties as well as investigating the effects of the operating environment on the developed material. Three material variants, differing in the number of layers used to produce the reinforcement, were used in this study. The tests were carried out on two-/three-/four-layer sheets produced by infusion. Due to the later use of the tested composites for the sheathing of a racing car, the results obtained were analysed in terms of the most favourable strength properties while keeping the weight as low as possible. In this study, the hardness, impact strength, and tensile and bending stresses of the developed composites were examined. In addition to the strength properties, the density, the effects of immersion in water, and the composite's resistance to staining and friction in the presence of aggressive media were also checked. The structure and the breakthroughs resulting from the strength tests were observed using a stereoscopic microscope. The material's resistance to sunlight and UVB was also tested. [ABSTRACT FROM AUTHOR]

In recent years, the study of urban flood resistance has included the perspectives of spatial environment and multiple elements of urban space, which break through the limitation of only focusing on engineering measures in traditional disaster prevention. The article constructs a flood prevention and mitigation index system under the perspective of resistance based on the basic work of urban physical examination and ignoring the variability of population size affected by floods in different regions. It also takes 6 districts and 6 counties under the jurisdiction of Zhengzhou City as the research object, combines the relevant data of 12 cities, uses the entropy weight method and the coefficient of variation method to determine the index weights comprehensively and introduces the barrier degree diagnosis model. This article carries out urban flood control and disaster reduction special physical examination, considers resistance obstacle factors and promotes strategy analysis and research. The results show that from the perspective of spatial distribution, the flood control and flood mitigation resistance of Zhengzhou City is in a "differential" distribution state and the high resistance areas are Erqi District, Jinshui District and Gongyi City. In general, the resistance index in the southwest region was higher than that in the northeast region and there was a significant difference between urban areas and counties, showing a medium-high and medium-low resistance status. From the results of the study, to improve the level of resistance to flood mitigation in each city, it is necessary to focus on the main obstacle factors that hinder the development of the city and to fundamentally improve the level of resistance to create a more livable and healthier city according to local conditions. [ABSTRACT FROM AUTHOR]

The development of additive manufacturing methods known as "3D printing" started in the 1980s. In these methods, spatial models are created from a semi-finished product such as a powder, filament or liquid. The model is most often created in layers, which are created from the semi-finished product, which is most often subjected to thermal treatment or using light or ultraviolet rays. The technology of additive manufacturing has both advantages and disadvantages when compared to the traditionally used methods of processing thermoplastic materials, such as, for example, injection or extrusion. The most important advantages are low cost, flexibility and speed of manufacturing of elements with different spatial shapes. From the point of view of the user of the product, the most important disadvantages are the lower mechanical properties and lower resistance to environmental factors that occur during the use of the manufactured products. The purpose of this review is to present current information and a compilation of features in the field of research on the effects of the interactions of different types of environments on the mechanical properties of 3D-manufactured thermoplastic products. Changes in the structure and mechanical properties of the material under the influence of factors such as humidity, salt, temperature, UV rays, gasoline and the environment of the human body are presented. The presented article enables the effects of environmental conditions on common materials used in 3D printing technology to be collated in one place. [ABSTRACT FROM AUTHOR]

Azole resistance is an emerging problem in patients with aspergillosis. The role of fungicides for resistance development and occurrence is not fully elucidated. EUCAST reference MICs of 17 fungicides (11 azoles and 6 others), five azole fungicide metabolites and four medical triazoles were examined against two reference and 28 clinical isolates of A. fumigatus, A. flavus and A. terreus with (n = 12) and without (n = 16) resistance mutations. Eight/11 azole fungicides were active against wild-type A. fumigatus, A. flavus and A. terreus, including four (metconazole, prothioconazole-desthio, prochloraz and imazalil) with low MIC50 (≤2 mg/L) against all three species and epoxiconazole, propiconazole, tebuconazole and difenoconazole also against wild-type A. terreus. Mefentrifluconazole, azole metabolites and non-azole fungicides MICs were >16 mg/L against A. fumigatus although partial growth inhibition was found with mefentrifluconazole. Moreover, mefentrifluconazole and axozystrobin were active against wild-type A. terreus. Increased MICs (≥3 dilutions) were found for TR34/L98H, TR34³/L98H, TR46/Y121F/T289A and G432S compared to wild-type A. fumigatus for epoxiconazole, propiconazole, tebuconazole, difenoconazole, prochloraz, imazalil and metconazole (except G432S), and for prothioconazole-desthio against TR46/Y121F/T289A, specifically. Increased MICs were found in A. fumigatus harbouring G54R, M220K and M220R alterations for five, one and one azole fungicides, respectively, compared to MICs against wild-type A. fumigatus. Similarly, increased MICs wer found for A. terreus with G51A, M217I and Y491H alterations for five, six and two azole fungicides, respectively. Azole fungicides showed activity against wild-type A. fumigatus, A. terreus and A. flavus, but not against all mutant isolates, suggesting the environmental route of azole resistance may have a role for all three species. [ABSTRACT FROM AUTHOR]

Environmental resistance is an important factor for understanding the epidemiology of leptospirosis. Recently, new Leptospira hosts were identified, including also marine mammals. Moreover, halotolerant Leptospira strain, isolated from the environment and animals, highlighted the capability of this microorganism to persist in the seawater. The aim of this research was to investigate the bacteriostatic and bactericidal effect of salt on Leptospira strains belonging to 16 different serovars. The minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) values were verified through the microdilutions method starting from a 20% sodium chloride concentration. MIC values obtained were between 0.3125% and 10% of salt, while MBC values between 0.625% and >20%. Icterohaemorrhagiae (MIC: 0.3125%; MBC: 0.625%) resulted the most inhibited serovar, while the most resistant was Tarassovi (MIC: 10%; MBC: >20%). Interestingly, trends were reported for Pomona (MIC: 1.25%; MBC: >20%) and Bratislava (MIC: 0.625%; MBC: 20%), highlighting low MIC values but high MBC values. This is the first investigation aimed at the in vitro effect of salt on the growth of Leptospira spp. reference strains. [ABSTRACT FROM AUTHOR]

The thermally conductive structural film adhesive not only carries large loads but also exhibits excellent heat-transfer performance, which has huge application prospects. Herein, a novel epoxy (Ep) thermally conductive structural film adhesive was prepared using polyphenoxy (PHO) as the toughening agent and film former, boron nitride (BN) nanosheets as the thermally conductive filler, and polyester fabric as the carrier. When the amount of PHO in the epoxy matrix was 30 phr and the content of nano-BN was 30 wt.% (Ep/PHO30/nBN30), the adhesive resin system showed good film-forming properties, thermal stability, and thermal conductivity. The glass transition temperature of Ep/PHO30/nBN30 was 215 °C, and the thermal conductivity was 209.5% higher than that of the pure epoxy resin. The Ep/PHO30/nBN30 film adhesive possessed excellent adhesion and peeling properties, and the double-lap shear strength at room temperature reached 36.69 MPa, which was 21.3% higher than that of pure epoxy resin. The double-lap shear strength reached 15.41 MPa at 150 °C, demonstrating excellent high temperature resistance. In addition, the Ep/PHO30/nBN30 film adhesive exhibited excellent heat-aging resistance, humidity, and medium resistance, and the shear strength retention rate after exposure to the complicated environment reached more than 90%. The structural film adhesive prepared showed excellent fatigue resistance in the dynamic load fatigue test, the double-lap shear strength still reached 35.55 MPa after 1,000,000 fatigue cycles, and the strength retention rate was 96.9%, showing excellent durability and fatigue resistance. [ABSTRACT FROM AUTHOR]