Search

The unusual combination of the fundamentally contradictory properties of high tensile strength and high fracture toughness found in maraging steel makes it well suited for safety-critical applications that require high strength-to-weight materials. In certain instances, additive manufacturing (AM) has produced materials that may be desirable for safety-critical applications where impact toughness is a key property, such as structural parts for the aerospace industry or armor plates for military applications. Understanding the influence of process parameters and defect structure on the properties of maraging steel parts produced via laser powder bed fusion (LPBF) is a fundamental step towards the broader use of AM technologies for more demanding applications. In this research, the impact energy of V-notched specimens made of 1.2709 maraging steel produced by LPBF was determined via Charpy impact testing. Specimens were produced using different processing parameter sets. By combining the process parameters with the porosity values of the parts, we demonstrate that an almost full prediction of the impact properties can be achieved, paving the way for significantly reducing the expenses of destructive testing. [ABSTRACT FROM AUTHOR]

Payloads for light unmanned free balloons must meet several safety requirements such as being able to protect the inner electronics in order to extract scientific data and to reduce the chance of inflicting personal injury in case of an accidental fall. This article proposes a novel payload structure, which exhibits the form of a dodecahedron. The actual form was determined by carrying out theoretical drop tests on different polyhedrons using the finite element method (FEM). From the simulations, it could be deduced that the dodecahedron was the optimal choice, since the duration of the impact was longer, while the impact force was slightly lower. The payload was produced by additive technologies; therefore, after performing tensile tests on probable materials, PLA was selected as the optimal candidate. The theoretical results about the dodecahedron's ability were validated by laboratory and real-life drop tests, where the new payload was subjected to 56% less impact force under a 78% longer collision time compared to a classic, rectangular cuboid design. Based on these tests, it was demonstrated that the new structure is safer and it is applicable. [ABSTRACT FROM AUTHOR]

Nowadays, there are numerous new features available in CFD (computational fluid dynamics) that can simulate complex physical phenomena, which used to be challenging to address. However, in current CFD software, certain problems can be simulated using different approaches. In our article, we chose different rotating motion methods to analyze a counter-rotating dual-rotor wind turbine (CO-DRWT). Using the different rotating motion approaches we selected (mixing plane, frozen rotor, and sliding mesh), we examined the torque on the rotors and compared them. The following conclusion was reached. If transient fluid flow must be examined, then the sliding mesh method provided the most realistic results, while the frozen rotor method was adequate if we investigated the effect of wake and vortex near the rotating blades or on its environment. The mixing plane method should be used when the focus is on the kinetics and kinematics of the rotating blade or structure. [ABSTRACT FROM AUTHOR]

Running-related limb asymmetries suggest specific sports injuries and recovery circumstances. It is debatable if running speed affected asymmetry, and more research is required to determine how longitudinal bending stiffness (LBS) affected asymmetry. The purpose of this study was to investigate the influence of running velocity and LBS on kinematic characteristics of the hip, knee, ankle, metatarsophalangeal joint (MTP) and the corresponding asymmetry. Kinematic (200 Hz) running stance phase data were collected bilaterally for 16 healthy male recreational runners (age: 23.13 ± 1.17, height: 175.2 ± 1.6 cm, body mass: 75.7 ± 3.6 kg, BMI: 24.7 ± 1.3 kg/m2) running on a force plate at three different velocities (10, 12 and 14 km/h) and three increasing-LBS shoes in a randomized order. The symmetry angle (SA) was calculated to quantify gait asymmetry magnitude at each running velocity and LBS. Changes in running velocity and LBS led to differences in kinematic variables between the hip, knee, ankle and MTP (p < 0.05). Significant changes in SA caused by running velocity were found in the knee flexion angle (p = 0.001) and flexion angle peak velocity (p < 0.001), ankle plantarflexion angle (p = 0.001) and plantarflexion angle peak velocity (p = 0.043) and MTP dorsiflexion angle (p = 0.001) and dorsiflexion angle peak velocity (p = 0.019). A significant change in the SA caused by LBS was found in the MTP dorsiflexion peak angle velocity (p = 0.014). There were interaction effects between running velocity and LBS on the MTP plantarflexion angle (p = 0.033) and plantarflexion angle peak velocity (p = 0.038). These findings indicate the existence of bilateral lower limb asymmetry. Meanwhile, it was proved that running velocity and LBS can influence the asymmetry of lower limb joints. Additionally, there was an interaction between running velocity and LBS on the asymmetry of the lower limb. These findings can provide some information for sports injuries, such as metatarsal stress fractures and anterior cruciate ligament injuries. They can also provide some useful information for running velocities and running shoes. [ABSTRACT FROM AUTHOR]

Although various sports footwear demonstrated marked changes in running biomechanical variables, few studies have yielded definitive findings on the underlying mechanisms of shoe constructions affecting running-related performance and injuries. Therefore, this study focused on examining the effect of basic shoe constructions on running biomechanics and assessing the current state of sports shoe production in terms of injury and efficiency. Relevant literature was searched on five databases using Boolean logic operation and then screened by eligibility criteria. A total of 1260 related articles were retrieved in this review, and 41 articles that met the requirements were finally included, mainly covering the influence of midsole, longitudinal bending stiffness, heel-toe drop, shoe mass, heel flare, and heel stabilizer on running-related performance and injuries. The results of this review study were: (1) The functional positioning of running shoe design and the target groups tend to influence running performance and injury risk; (2) Thickness of 15–20 mm, hardness of Asker C50-C55 of the midsole, the design of the medial or lateral heel flares of 15°, the curved carbon plate, and the 3D printed heel cup may be beneficial to optimize performance and reduce running-related injuries; (3) The update of research and development concepts in sports biomechanics may further contribute to the development of running shoes; (4) Footwear design and optimization should also consider the influences of runners' strike patterns. [ABSTRACT FROM AUTHOR]

The aim of this study is to review the valuable lower limb biomechanical contribution to table tennis topspin forehand. Databases included Scopus, PubMed, and Web of science. In this case, 19 articles were selected for the systematic review. The mechanics of the plantar, lower limb joints kinematics and kinetics, muscle activity, and racket-joint relationship are described through gender, performance level, and footwork. The study found that the hip movement characteristics and the hip muscle group activity following a proximal-to-distal sequence strategy significantly contributed to the maximum acceleration of the racket. Optimizing the motion strategy of the ankle and plantar as well as the ankle muscle group activity is beneficial for the transmission of energy in the kinetic chain. Muscle groups around the ankle and subtalar joints are heavily activated during landing to maintain foot stability during the landing phase. Lower limb muscle development plays an important role in movement control and stability as well as sports injury prevention in table tennis footwork during the performance of the topspin forehand. Furthermore, physical development levels and anatomical differences (such as hip and lower trunk muscle strength differences), maybe the main reasons for gender differences observed during the topspin forehand. Systematically summarizing this valuable information can contribute to athletes' and coaches' knowledge to enhance topspin forehand performance and training regimes. We suggest that future research could consider the joint contact forces, ball movement, and ball-racket impact during a performance of topspin forehand. [ABSTRACT FROM AUTHOR]

In this paper, to investigate the independent effect of the construction of the forefoot carbon-fiber plate inserted to the midsole on running biomechanics and finite element simulation, fifteen male marathon runners were arranged to run across a runway with embedded force plates at two specific running speeds (fast-speed: 4.81 ± 0.32 m/s, slow-speed: 3.97 ± 0.19 m/s) with two different experimental shoes (a segmented forefoot plate construction (SFC), and a full forefoot plate construction (FFC)), simulating the different pressure distributions, energy return, and stiffness during bending in the forefoot region between the SFC and FFC inserted to midsole. Kinetics and joint mechanics were analyzed. The results showed that the footwear with SFC significantly increased the peak metatarsophalangeal joint (MTPJ) plantarflexion velocity and positive work at the knee joint compared to the footwear with FFC. The results about finite element simulation showed a reduced maximum pressure on the midsole; meanwhile, not significantly affected was the longitudinal bending stiffness and energy return with the SFC compared to the FFC. The results can be used for the design of marathon running shoes, because changing the full carbon fiber plate to segment carbon fiber plate induced some biomechanical transformation but did not significantly affect the running performance, what is more, reducing the peak pressure of the carbon plate to the midsole by cutting the forefoot area of the carbon fiber plate could be beneficial from a long-distance running perspective for manufacturers. [ABSTRACT FROM AUTHOR]

Polylactic acid (PLA)-made machine elements exhibit easy machining, biodegradability, and excellent mechanical properties. However, enhancing their wear resistance is still a crucial engineering point, which may be achieved by altering (lowering) their coefficient of friction (CoF). Therefore, the first aim of this paper is to analyze how wear is affected by the alteration of CoF. The second aim is connected to the fact that PLA is sensitive to heat, which also limits its applicability. Accordingly, the next goal is to explore the effect of temperature on wear propagation. This study answers these questions by means of multibody dynamics simulations of a PLA-made spur gear pair. Simulations were carried out under constant torque, while the CoF and the temperature were varied in a normal operation domain (CoF: 0.1–0.05, T = 20–30 °C). The results showed that the wear volume gradually began to decline at approximately 0.085 CoF, whilst convergence to steady-state wear could be observed at 0.05 CoF. In conclusion, alteration of the CoF can lower wear by 35%, in this specific domain, while even a 5 °C rise in temperature causes 40% wear progression. The feasibility of the numerical procedure was validated by comparing numerically and experimentally obtained wear–torque results. [ABSTRACT FROM AUTHOR]

AlCrCoNiFeCTax (x = 0, 0.5 and 1.0) high-entropy alloys coatings were synthesized on 45# steel by laser cladding. The microstructural evolution of the coatings with the change in x was analyzed in detail. The effect of Ta content on the wear behaviors of the coatings at different circumstances (in air and 3.5 wt.% NaCl solution) was especially highlighted. The microstructure presented the following change: equiaxed BCC (Body Centered Cubic) grains + fine MC (carbide, M = Al, Cr, Co and Ni) particles (x = 0) → equiaxed BCC grains + coarse TaC blocks + fine TaC particles (x = 0.5) → flower-like BCC grains + coarse TaC blocks + eutecticum (BCC + TaC) (x = 1.0). The average microhardness of the coatings demonstrated an upward tendency with increasing x due to the combination of the stronger solid solution and dispersion strengthening from the significant difference in atomic radius between Ta and Fe and the formation of TaC with an extremely high hardness. The wear rates of the coatings were gradually reduced both in air and in NaCl solution along with the increase in Ta content, which were lower than those of the substrate. The wear rates of the coatings with x = 0.5 and 1.0 in NaCl solution were slightly reduced by about 17% and 12% when compared with those in air. However, the values of the substrate and the coating without Ta in NaCl solution were sharply enhanced by 191% and 123% when compared with those in air. This indicated that the introduction of Ta contributed to the improvement in wear resistance both in air and in NaCl solution. [ABSTRACT FROM AUTHOR]

The aim of this study was to examine whether there are kinematic and kinetic differences in the lower limb and whether the symmetry of the lower extremities is different after prolonged-running. Fifteen healthy male amateur runners (age: 22 ± 1 years, height: 173 ± 8 cm, mass: 65 ± 7 kg, BMI: 21.62 ± 2 kg/m2) were recruited as participants for this study. A Vicon eight-camera motion capture system and Kistler force plate were used to collect kinematic and kinetic parameters. A motorized treadmill, 15-point Borg scale and heart rate bands were used to monitor fatigue during a running-induced fatigue protocol. Paired sample T tests were used to check statistical difference (p = 0.05) between the lower limbs and the symmetry changes in pre-fatigue and post-fatigue running sessions. The symmetry angle (SA) of the knee flexion angle, hip flexion angle and hip extension angle in post-fatigue was significantly greater than in pre-fatigue, increasing by 4.32%, 10.71%, and 23.12%, respectively. Moreover, the SA of hip flexion moment increased by 2.61%. However, the knee extension velocity and hip flexion velocity became more symmetrical than in pre-fatigue (p < 0.05), the SA decreased by 5.91% and 5.45%, respectively. Differences in limb function during post-fatigue may lead to changes of symmetry in the lower limbs. The variables of asymmetry may be used as a compensation mechanism to maintain gait stability. Physical therapy assessment of fatigue injuries and long-distance running training programs may want to consider the changes in symmetry due to limb dominance. [ABSTRACT FROM AUTHOR]